Gree Electric Appliances of Zhuhai CS532Y WiFi Module User Manual 66162390

Gree Electric Appliances, Inc. of Zhuhai WiFi Module 66162390

User Manual

Special note: matching instructionsMatching of remote controllerPlease done the following operation within 2m from the unit. Matching is not needed anymore once it is done. During matching, please keep the remote controller and air conditioner under standby status.When the signal of remote controller can’t be received, please match the remote controller with the unit again.This model adopts RF remote control. The remote controller shall be matched with the air conditioner before operation, otherwise the remote control willbe invalid.Before operation, please read the instructions in this page carefully and then do the corresponding match-ing operation.NoteWhen the unit is under standby status, please get close to the air conditioner within 2m and then hold on pressing button for 3s. The remote controller and air conditioner will enter matching automatically. If matching is done, the unit will give out three sounds; if matching is failed, please get closer to the unit and arrange matching again. 66162390/
Wifi SmartThank you for choosing our product.If you have lost the Owner’s Manual, please contact the local agent or visit www.gree.com or sent email to global@gree.com.cn for electronic version.For proper operation, please read and keep this manual carefully.
ContentDownload and install App.........................................................................Configuration..................................................................................................User registration.................................................................................................... 3311Personal setting.................................................................................................... 4Control functions................................................................................................... 615Menu functions........................................The software is subject to be updated without prior notice. ............................................................Functions introduction...............................................................................
Operation of Smart Control (Smart Phone, Tablet PC)Scan the following QR code (also indicated on package box) with your smart phone and download Wifi Smart.Download and install AppConfigurationphone homepage will show this icon Before operation, please finish the following configuration in order to realize Wifi control and the connection between air conditioner and intelligent device.1.Short-distance control setting for air conditioner using wifi hotspotStep 1: Air conditioner wifi is set to AP mode in factory. You can search the air conditioner wifi hotspot through your smart phone. The name of wifi hotspot is the last 8 numbers of the air conditioner mac address. Password is 12345678.Install the App according to its guidance. When successfully installed, your smart Operation Instructions1
Operation of Smart Control (Smart Phone, Tablet PC)2Step 2: Open App and the screen will show the air conditioner that you just connected. Click this air conditioner to enter and realize short-distance control, as shown below. Please refer to "Functions introduction" for specific control methods. 2.Short-distance and long-distance control setting for air conditioner connecting routerStep 1: Under short-distance control, return to the homepage "Device". Tap at the top right corner of the homepage "Device". Select "Add device" and enter the page of "Add device". Tap "Manual configuration" and enter the page "Manual configuration"."wpa2" and select the server,then tap the button "Add device" for configuration. If Step 2: Enter the correct network name and password, select the encrypt mode
Operation of Smart Control (Smart Phone, Tablet PC)31.User registration Purpose: To realize long-distance controlOperation instruction: For the first time login, you have to register a new username. If you already have a username, skip the registration step and enter email address and password on the "Login Page" to log in. If password is forgotton, you can reset the password.Operation steps:(1) Account login: Slide the page "Device". and enter the page "Menu" on the left. Tap "Login" to enter the page "Register username". New user must first register a username. Tap "Register”.Functions introductionNOTICE:Please select the encrypt mode "empty" if your wifi has been set without password. configuration succeeds, App will notify user that configuration is successful and return to homepage.
Operation of Smart Control (Smart Phone, Tablet PC)4(3) If password is forgotten, you can reset the password with your email address.(2) Enter your email address and tap "Get verification code". Wait until you receive the verification code. Enter the code and then tap "OK" to log in. Username will appear. As shown here, the username is "test".Tap "Forgot password" and enter the page "Forgot password". Tap "Verification code"to get a email verification code. Enter a new password and tap "OK" to log in.2.Personal settingsPurpose: Set name (device name, preset name, etc.) and images (device image) in order to identify a user easily. (1) Set device nameAfter quick configuration, a list of controllable smart devices will be generated. Default name for air conditioner is "AC".
Operation of Smart Control (Smart Phone, Tablet PC)5Step 2: Tap "Name" to change device name,enable button ''Lock device'' to lock the Step 1: Tap and hold "babyroom" to enter the page "Edit device". Tap "Image" to select the source of image. Select from "Default images" or "Take photo" or "Choose from photos" and save an image. device. Save it and the new device name will be shown.
Operation of Smart Control (Smart Phone, Tablet PC)6Step 2: Choose the time. Tap "Name". As shown in the picture, its name is "baby (2) Set preset nameStep 1: Tap at the top right corner of the homepage "Device". Select "Add preset" and enter the page "Preset edit".room". For timer type, select "On". Then select the repeating days. Save the setting of preset name.(3) Set device imagePlease refer to step 1 in 2(1)3.Control functions (1) Common control functions: General control on the operation of smart devices (On/Off, temperature, fan speed, mode, etc.) and the setting of advanced functions (air exchange, dry, health, light, sleep, energy saving upper limit).Step 1: General control Enter the homepage "Device" first. Take "baby home" as an example.
Operation of Smart Control (Smart Phone, Tablet PC)7Tap "babyroom" and enter the page of air conditioner control. Tap to turn on the control switch.Tap or to increase or decrease temperature. Tap to changeworking mode. Tap to enter the page of fan speed adjustment.
Operation of Smart Control (Smart Phone, Tablet PC)8Tap and go around the circle to adjust fan speed. Step 2: Advanced settings Tap to enter advanced settings. You may select "Air", "Dry", "Health", "Light", "Sleep" or "Energy saving".(2) Advanced control functions: Set scene; Preset; Link: Infrared control (only applicable to smart phone with infrared emitter)Set scene: Preset the operation of several smart devices by one tap. On the page "Device", tap the image of "Device" to enter the page "Edit scene".Tap "Add scene" and edit the scene name, for example, "Back home". Add execution devices.Tap to add commands. On the page "Select execution device", select the air conditioner named "babyroom". Then select "ON" or "OFF".
Operation of Smart Control (Smart Phone, Tablet PC)9Continue to select the next execution device as instructed above. Tapto set the interval.Tap "Save". Then the scene "Back home" will be in execution. You may view the execution condition of the scene.(3) Preset includes single-device preset and multi-device presetSingle-device preset: This can preset a certain device to be On/Off at a specific time.
Operation of Smart Control (Smart Phone, Tablet PC)10On the homepage "Device", take air conditioner "babyroom" as an example. Tap at the bottom of the page "babyroom". Then you will enter the page Slide up and down to set the time. If you want to synchronize the time, tap " synchronize". "Preset edit".Tap "Name" to customize the preset name.Preset device can’t be selected and it will default to "babyroom". Select "On" for the timer type. Select repeating days to complete the preset.
Operation of Smart Control (Smart Phone, Tablet PC)11Multi-device preset: This can preset multiple devices to execute a command at a specific time.Please refer to the instructions as how to set preset time, name, timer type and repeating days for a single device.Tap "Preset device" to select one or more devices. Then return to the page "Device".(4) Link(This function is applicable to partial of models)set in the master device, slave devices will execute commands to realize devices Select a master device. When the environment has satisfied the parameters as linkage.Step 1: Set the parameters of master device (Select master device, select environment parameters, select master device status).Tap at the top right corner of the homepage "Device". Select "Link" and enter the page "Add linkage". Tap "Device parameter" to enter the page "Select device". Take "baby room" as an example. Tap "babyroom".Enter the page "Select environment parameters".
Operation of Smart Control (Smart Phone, Tablet PC)12Tap "Temperature" to enter the page "Select temperature parameter". Slide up or down to adjust temperature. Tap "Upper limit" or "Lower limit".Tap "Mode" and "On/Off" to select the status of master device. Then tap "Save".Step 2: Set time parameter for linkage. Tap "Time parameter" to enter the page "Set time". Slide rightwards to turn on the setting time.Tap "Execution time"; Then tap "Start" and "Stop" to set start time and stop time respectively. Tap "OK" at the top right corner to save the setting.
Operation of Smart Control (Smart Phone, Tablet PC)13Tap the days below "Repeat" to select the repeating days. Then tap "Save".Step 3: Select "Execute command"Tap "Execute command" and enter the page "Select device".Tap the name of device that you want to control. Tap "ON" or "OFF" and then tap "Save" to complete the linkage.
Operation of Smart Control (Smart Phone, Tablet PC)14Tap "Save" and then repeat the above steps to set linkage of several scenes.(5) Infrared control (only applicable to smart phone with infrared emitter).Function: Smart phone can be used as a remote controller.Tap at the top right corner of the homepage "Device". Select "Infrared" and enter the page "Remote controller". Tap and slide up to enter the page of advanced functions.
Operation of Smart Control (Smart Phone, Tablet PC)15Tap to turn on the device. Tap to select mode. Tap to adjust fan speed . Tap "Health", "Energy saving", "Sleep" etc. to set advanced functions. Tap "Sleep" to enter the page "Sleep". You can select "Traditional sleep", "Expert sleep" or "DIY sleep". Tap "DIY sleep" and then tap the left and right arrows to set sleep time. Tap up and down arrows to adjust temperature at a specific sleep time.Menu functions (Share, Set, History, Feedback)(1) Share: To share quick configuration information and unit’s information, including local export and local import. For local import, you just need to tap "Local import" and wait for the data download.Local export Step 1: Export local data to another smart phone. Enter "Menu" on the left side and tap "Share" to enter the page "Share". Then tap "Local export".4.Menu functions
Operation of Smart Control (Smart Phone, Tablet PC)16Step 2: Another smart phone to be imported.Tap the model name and wait for the download.(2) Backup: To keep backup of the quick configuration information and unit’s information, including backup to cloud and backup list on the cloud.Backup to cloudEnter the "Menu" on the left and tap "Backup".Tap "Backup to cloud" and then tap "Yes". Then wait for the data download.
Operation of Smart Control (Smart Phone, Tablet PC)17Select "Backup list on the cloud". Then backup records will appear. Tap "Record" to download data and recover data to local unit.(3) SettingsUser can set vibration, message alerts, gesture password (usable only after registration), etc.User can feedback suggestions to back-stage management for maintenance and development.Tap "Feedback". Enter your suggestions and then submit it.(4) Feedback
Explanation of SymbolsIndicates a hazardous situation that, if not avoided, willresult in death or serious injury.Indicates a hazardous situation that, if not avoided, could result in death or serious injury. Indicates a hazardous situation that, if not avoided, mayresult in minor or moderate injury.Indicates important but not hazard-related information, used to indicate risk of property damage. Indicates a hazard that would be assigned a signal word WARNING or CAUTION.
The indoor unit should be installed close to the wall.reachable after finishing installation.far away from animals or plants.If it is unavoidable, please add the fence for safety purpose.PrecautionsWARNINGFCC WARNINGplace, only the qualified person can perform the work. Otherwise, it may cause personal injury or damage.If you need to relocate the air conditioner to another must be installed in the line.For the air conditioner without plug, an circuit break Select a location which is out of reach for children and For the air conditioner with plug, the plug should be5Instructions for installation and use of this product are provided by the manufacturer.expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.WARNING: Changes or modifications to this unit not FCC STATEMENTOperation is subject to the following two conditions : This device complies with Part 15 of the FCC Rules.
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against equipment generates, uses and can radiate radio Ɣ Reorient or relocate the receiving antenna.Ɣ Increase the separation between the equipment and receiver.Ɣ Connect the equipment into an outlet on a circuit Ɣ Consult the dealer or an experienced radio/TV different from that to which the receiver is connected. technician for help.interference to radio communications. comply with the limits for a Class B digital device, PrecautionsFCC STATEMENTaccordance with the instructions,may cause harmful harmful interference in a residential installation. This undesired operation.frequency energy and, if not installed and used in However, there is no guarantee that interference will does cause harmful interference to radio or television correct the interference by one or more of the following measures:equipment off and on, the user is encouraged to try to not occur in a particular installation. If this equipment reception, which can be determined by turning the NOTE: This equipment has been tested and found to (1) this device may not cause harmful interference, and (2) this device must accept any interference received,including interference that may cause 6
PrecautionsLe présent appareil est conforme aux CNR d'Industrie licence. L'exploitation est autorisée aux deux conditions tout brouillage radioélectrique subi, même si le undesired operation of the device.IC STATEMENTbrouillage, et (2) l'utilisateur de l'appareil doit accepter Canada applicables aux appareils radio exempts de interference, and (2) this device must accept any suivantes : (1) l'appareil ne doit pas produire de brouillage est susceptible d'en compromettre le fonctionnement.interference, including interference that may cause This device complies with Industry Canada licence-This equipment complies with FCC’s and IC’s RF radiation exposure limits set forth for an uncontrolled environment. The antenna(s) used for this transmitter must be installed and operated to provide a separation distance of at least 20 cm from all persons and must exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause not be collocated or operating in conjunction with any other antenna or transmitter. Installers must ensure that 20cm separation distance will be maintained between the device (excluding its handset) and users.Cet appareil est conforme aux limites d’exposition au rayonnement RF stipulées par la FCC et l’IC pour une utilisation dans un environnement non contrôlé. Les 7
PrecautionsWorking temperature rangeIndoor side DB/WB(ć) Outdoor side DB/WB(ć)Maximum cooling 26.7/19.4 46.1/23.9Maximum heating 26.7/- 23.9/18.3ƔThe operating temperature range (outdoor temperature) for cooling only unit is -18 ć~54ć; for heat pump unit is -30 ć~ 54ć.NOTICE:IC STATEMENTprès d’autres antennes ou émetteurs ou fonctionner antennes utilisées pour cet émetteur doivent être installées et doivent fonctionner à au moins 20 cm de distance des utilisateurs et ne doivent pas être placées distance de 20 cm sépare l’appareil (à l’exception du combiné) des utilisateurs.avec ceux-ci. Les installateurs doivent s’assurer qu’une 8
Add: West Jinji Rd, Qianshan, Zhuhai, Guangdong, China, 519070Tel: (+86-756) 8522218 Fax: (+86-756) 8669426E-mail: gree@gree.com.cn www.gree.comGREE ELECTRIC APPLIANCES, INC. OF ZHUHAI66160000321

Navigation menu