Greenheck Fan Combination Fire Smoke Dampers Fsd M211 Users Manual
FSD-M211 to the manual 74d69a7b-5312-4e35-b469-aeb72681996b
2015-02-09
: Greenheck-Fan Greenheck-Fan-Combination-Fire-Smoke-Dampers-Fsd-M211-Users-Manual-562482 greenheck-fan-combination-fire-smoke-dampers-fsd-m211-users-manual-562482 greenheck-fan pdf
Open the PDF directly: View PDF 
.
Page Count: 6
| Download | |
| Open PDF In Browser | View PDF |
Combination FIRE SMOKE DAMPERS Model FSD-M211 Application Model FSD-M211 is a combination fire smoke damper with 3V style blades. The FSD-M211 has been qualified to 10.2 m/s and 1 kPa for operation and dynamic closure in emergency fire smoke situations. Model FSD-M211 may be installed vertically (with blades running horizontal) or horizontally and is rated for airflow and leakage in either direction. Model FSD-M211 has also been tested in accordance with BS476 to 4 hours at Warrington Fire, UK, and is approved for fire partitions of 4 hours or less where British Standards are required. Ratings UL 555 Fire Resistance Rating Fire Rating: 11⁄2 Hours Dynamic Closure Rating: Actual ratings are size dependant Maximum Velocity: 10.2 m/s Maximum Pressure: 1 kPa UL 555S Leakage Rating Leakage Class: I Operational Rating: Actual ratings are actuator dependant Maximum Velocity: 10.2 m/s Maximum Pressure: 1 kPa Max. Temperature: 177°C —Depending on actuator Steel 3V Blades UL 555S Leakage Class I UL555 11⁄2 Hour Fire Resistance Rating 4 Hour Fire Resistance Rating (BS476) Model FSD-M211 meets the requirements for fire dampers, smoke dampers and combination fire smoke dampers established by: National Fire Protection Association NFPA Standards 80, 90A, 92A, 92B, 101, & 105 IBC International Building Codes ICBO Uniform Building Codes SBCCI Standard Building Codes British Standard BS476 Tested to 4 hours at Warrington Fire, UK “UL CLASSIFIED (see complete marking on product)” “UL CLASSIFIED to Canadian safety standards (see complete marking on product)” Standard 555 & 555S (Listing #R13317) BS476 Fire Resistance Rating Fire Rating: 4 hours AIR Standard Construction Frame: Blades: Seals: Closure Device: Linkage: Axles: Bearings: Size Limitations Minimum Size: Maximum Size: Single Section: Multiple Section: PERFORMANCE 127mm x 25mm galv. steel hat channel with reinforced corners . A low profile head and sill are used on sizes less than 432mm high to maximize free area and performance. 1.5mm galvanized steel, reinforced with 3 longitudinal structurally designed vee’s. Extruded silicone rubber blade seals. Flexible stainless steel jamb seals. 74°C RRL Concealed in jamb. 13mm diameter plated steel Bronze sleeve type. AIR MOVEMENT AND CONTROL ASSOCIATION INTERNATIONAL, INC. ® Greenheck Kunshan Co. Ltd. and Greenheck Fan Corporation certifies that the model FSD-M211 shown herein is licensed to bear the AMCA Seal. The ratings shown are based on tests and procedures performed in accordance with AMCA Publication 511 and comply with the requirements of the AMCA Certified Ratings Programs. The AMCA Certified Ratings Seal applies to air performance ratings only. W 101mm W x 101mm H 813mm W x 1270mm H or 914mm W x 914mm H 3251mm W x 2540mm H Vertical or 3658mm W x 2438mm H Horizontal RH H Optional Features • Stainless steel bearings • 100°C, and 177°C RRL available (UL only) • 69°C fusible link (BS476) • Electric or pneumatic actuators to accomplish smoke management and system functions. • Sleeve with Integral flange on both sides available • RRL/OCI (open close indication) • TOR (remote override of 74°C or 100°C closure allows damper to perform smoke management functions during a fire emergency) LH * W & H dimensions furnished approximately 6mm undersize. (Add sleeve thickness for overall sleeved damper dimension) Right hand drive is shown. Left hand drive is available upon request. Installation instructions available at www.greenheck.com Pressure Drop Data FSD-M211 This pressure drop testing was conducted in accordance with AMCA Standard 500-D using the three configurations shown. All data has been corrected to represent standard air at a density of 1.201 kg/m3. Actual pressure drop found in any HVAC system is a combination of many factors. This pressure drop information along with an analysis of other system influences should be used to estimate actual pressure losses for a damper installed in a given HVAC system. AMCA Test Figures Figure 5.3 Illustrates a fully ducted damper. This configuration has the lowest pressure drop of the three test configurations because entrance and exit losses are minimized by straight duct runs upstream and downstream of the damper. Figure 5.2 Illustrates a ducted damper exhausting air into an open area. This configuration has a lower pressure drop than Figure 5.5 because entrance losses are minimized by a straight duct run upstream of the damper. Figure 5.5 Illustrates a plenum mounted damper. This configuration has the highest pressure drop because of extremely high entrance and exit losses due to the sudden changes of area in the system. 5D 6D 5D D 4 (W) (H) 3.14 Figure 5.3 AMCA 5.2 Pressure Drop FSD-M211 5D 4 (W) (H) 3.14 D= Figure 5.2 7&-0$*5:7413&4463&%301 13&4463&%3011"4$"-4 Y NNYNN NNYNN NNYNN NNYNN NNYNN Y Y Y Figure 5. 5 Y '"$&7&-0$*5:.&5&344&$0/% ".$" 305mm x 305mm 610mm x 610mm Velocity (m/s) Pressure Drop (Pa) Velocity (m/s) 2.5 10 5.1 35 7.7 914mm x 914mm 305mm x 1219mm Pressure Drop (Pa) Velocity (m/s) 2.6 3 5.1 10 42 7.6 Pressure Drop (Pa) Velocity (m/s) 2.5 5 5.2 17 80 7.8 1219mm x 305mm Pressure Drop (Pa) Velocity (m/s) Pressure Drop (Pa) 2.5 3 2.5 8 5.1 15 5.1 27 22 7.6 32 7.7 57 10 135 10.3 72 10.2 42 10.3 57 10.3 105 12.6 207 12.9 115 12.7 65 12.9 90 12.9 164 15.5 311 15.4 162 15.3 95 15.3 125 15.6 242 17.8 411 18.1 224 17.7 127 18 174 17.9 316 20.8 561 20.8 296 20.3 167 20.5 227 20.7 424 R Greenheck Kunshan Co. Ltd. and Greenheck Fan Corporation certifies that the model FSD-M211 shown herein is licensed to bear the AMCA Seal. The ratings shown are based on tests and procedures performed in accordance with AMCA Publication 511 and comply with the requirements of the AMCA Certified Ratings Programs. The AMCA Certified Ratings Seal applies to air performance ratings only. AMCA 5.3 Pressure Drop FSD-M211 5D 6D Figure 5.3 7&-0$*5:7413&4463&%301 5D D= 4 (W) (H) 3.14 Y Y Y 13&4463&%3011"4$"-4 Figure 5.2 NNYNN NNYNN NNYNN NNYNN NNYNN Y Y Figure 5. 5 '"$&7&-0$*5:.&5&344&$0/% ".$" 305mm x 305mm Velocity (m/s) 610mm x 610mm Pressure Drop (Pa) Velocity (m/s) 2.4 5 5.1 22 7.8 914mm x 914mm 305mm x 1219mm Pressure Drop (Pa) Velocity (m/s) Pressure Drop (Pa) Velocity (m/s) 2.5 3 2.5 3 5 10 5.1 8 52 7.7 22 7.6 10.3 92 10.3 40 12.9 145 12.8 62 15.4 209 15.5 17.7 274 17.9 20.8 379 20.8 167 R 1219mm x 305mm Pressure Drop (Pa) Velocity (m/s) 2.5 3 2.5 5 5.1 10 5.1 20 15 7.7 25 7.6 40 10.1 27 10.3 42 10.1 72 12.8 42 12.9 67 12.7 112 92 15.3 62 15.7 100 15.3 164 122 17.7 82 18.7 140 18 227 20.3 107 20.9 174 20.6 299 Greenheck Kunshan Co. Ltd. and Greenheck Fan Corporation certifies that the model FSD-M211 shown herein is licensed to bear the AMCA Seal. The ratings shown are based on tests and procedures performed in accordance with AMCA Publication 511 and comply with the requirements of the AMCA Certified Ratings Programs. The AMCA Certified Ratings Seal applies to air performance ratings only. Pressure Drop (Pa) 4 (W) (H) 3.14 D AMCA 5.5 Pressure Drop FSD-M211 VELOCITY VS. PRESSURE DROP 1000 305mm x 305mm 610mm x 610mm 914mm x 914mm 5 0 91 30 4 5 x x 91 12 4 19 30 1219mm x 305mm 61 61 0 x 5 x 30 x 19 12 5 100 30 PRESSURE DROP- PASCALS 305mm x 1219mm 10 2 5 10 30 FACE VELOCITY- METERS/SECOND AMCA 5.5 305mm x 305mm 610mm x 610mm Velocity (m/s) Pressure Drop (Pa) Velocity (m/s) 2.5 13 5 55 914mm x 914mm Pressure Drop (Pa) Velocity (m/s) 2.5 8 5 35 305mm x 1219mm Pressure Drop (Pa) Velocity (m/s) 2.5 8 5.1 30 1219mm x 305mm Pressure Drop (Pa) Velocity (m/s) Pressure Drop (Pa) 2.6 8 2.5 1 5.1 32 5 42 7.5 122 7.6 75 7.7 67 7.7 75 7.7 95 10.2 222 10.3 140 10.2 115 10.2 130 10.3 172 12.7 349 12.8 217 12.9 184 12.7 202 12.7 264 15.4 508 15.3 309 15.5 269 15.5 301 15.3 381 17.9 688 17.7 409 18.1 354 18.1 416 17.9 521 20.6 907 20.8 568 20.6 471 20.6 536 20.8 707 R Greenheck Kunshan Co. Ltd. and Greenheck Fan Corporation certifies that the model FSDM211 shown herein is licensed to bear the AMCA Seal. The ratings shown are based on tests and procedures performed in accordance with AMCA Publication 511 and comply with the requirements of the AMCA Certified Ratings Programs. The AMCA Certified Ratings Seal applies to air performance ratings only. Damper Sizing Information The following figures show maximum damper section size. 38mm ma Single Section W 95mm 152mm . H Varies 127mm . A 137mm A * 305mm 127mm Sleeve Length Damper Sleeve Dimensional Data The drawings below and corresponding table show the position of the FSD-M211 damper when mounted in a factory sleeve. The standard mounting locations provide enough space for the mounting of actuators, controls and allow space for installation of retaining angles and duct connections. 38mm max. The "A" dimension is the location of the damper mounted in a factory sleeve. The table below shows the Standard, Minimum, and Maximum “A” dimensions. 95mm "A" Dimension in. (mm) 152mm LH All Dampers* Varies 137mm When H is 11 in. (279mm) or less with OCI, RRL, or TOR RH Right hand drive is shown Left hand drive available upon request A 127mm Standard Maximum 7 3/16 (183) 12 (305) 12 (305) 12 (305) *With the exception of dampers 10 in. high (254mm) or less. NOTE: Entire damper frame is not required to be installed within the wall. The damper blades, when closed should be contained within the wall. Sleeve Length Specifications Combination Fire Smoke Dampers meeting the following specifications shall be furnished and installed where shown on plans and/or as described in schedules. Dampers shall meet the requirements of the latest edition of NFPA 80, 90A, 92A, 92B, 101, and 105. T* Dampers shall be tested , rated and labeled in accordance with the latest S edition of UL Standards 555 and 555S. Dampers shall have a UL 555 fire rating of 11⁄2 hours. Each damper shall be equipped with a heat responsive device which has been tested and approved for use with the damper assembly in accordance with UL 555. The heat responsive device shall have a temperature rating of (specifier select one of the following) 74°C, 100°C, or 177°C. Dampers shall be UL labeled for use in dynamic systems. The damper shall have a dynamic closure airflow rating equal to or greater than the airflow at the damper’s installed location and a dynamic closure pressure rating of 1 kPa. Dampers shall have a UL 555S Leakage rating of Class I and a Temperature rating of 177°C. Dampers shall have a UL 555S operational airflow rating equal to or greater than the airflow at its installed location and an operational pressure rating of 996 Pa. Damper actuators shall be factory mounted and qualified for use with the damper in accordance with UL 555S. Damper actuators shall be (specifier select one of the following) electric type for 120 (24 or 230) volt operation or pneumatic type for 25 psi minimum (30 psi maximum) operation. Manufacturers submittal data shall indicate B* actuator space requirements around the damper. All UL 555 and 555S Dynamic Closure Ratings, Operational Ratings and Leakage Ratings shall be qualified for airflow and pressure in either direction through the damper. UL ratings shall allow for mounting damper vertically (with blades running horizontal) or horizontally. The Damper Manufacturers submittal data shall certify all air performance pressure drop data is licensed in accordance with the AMCA Certified Ratings Program for Test Figures 5.2, 5.3 and 5.5. Damper air performance data shall be developed in accordance with the latest edition of AMCA Standard 500-D. Dampers shall be labeled with the AMCA Air Performance Seal. Damper blades shall be 1.5mm galvanized steel 3V type with three longitudinal grooves for reinforcement. Blades shall be completely symmetrical relative to their axle pivot point, presenting identical resistance to airflow and operation in either direction through the damper (blades that are non-symmetrical relative to their axle pivot point or utilize blade stops larger than 13mm are unacceptable). Damper frames shall be galvanized steel formed into a structural hat channel shape with reinforced corners. Bearings shall be sintered bronze sleeve type rotating in extruded holes in the damper frame. Jamb seals shall be stainless steel compression type. Basis of design is Greenheck Model FSD-M211. GREENHECK Greenheck Kunshan Co Ltd. 17 Qunyi Minying District • Kunshan Economic & Technical Development Zone Kunshan, Jiangsu, China 215300 Tel: 0512-573-66666 • Fax: 0512-573-78633 www.greenheck.com Copyright © 2008 Greenheck Fan Corporation FSD-M211 Rev. 6 January 2008
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : 3.1-702 Create Date : 2008:10:22 15:08:26-05:00 Metadata Date : 2008:10:23 07:36:41-05:00 Modify Date : 2008:10:23 07:36:41-05:00 Creator Tool : Adobe InDesign CS3 (5.0.2) Thumbnail Format : JPEG Thumbnail Width : 256 Thumbnail Height : 256 Thumbnail Image : (Binary data 12632 bytes, use -b option to extract) Instance ID : uuid:916f3aa1-cbcc-4841-99a3-239694f18125 Document ID : adobe:docid:indd:ceb1e7dd-c9d7-11dc-bbb6-de73c397c805 Rendition Class : proof:pdf Derived From Instance ID : 93fa508e-a1de-11dc-bc5d-c1600478f0c8 Derived From Document ID : adobe:docid:indd:8b155768-d84b-11d9-b474-c1fd45b03ec2 Manifest Link Form : ReferenceStream, ReferenceStream, ReferenceStream Manifest Placed X Resolution : 72.00, 72.00, 72.00 Manifest Placed Y Resolution : 72.00, 72.00, 72.00 Manifest Placed Resolution Unit : Inches, Inches, Inches Manifest Reference Instance ID : uuid:4a7b0a5a-381c-423d-b6d1-bc1e04be6e57, uuid:c72b7063-bf92-4a99-af8d-d900194c4c40, uuid:42ff821a-900d-457d-a42a-2da4dcc82216 Manifest Reference Document ID : uuid:f2c0832d-66bf-406f-a711-bdbc67f9a7e2, uuid:ded0ca52-5f88-45f9-bff9-6ad59c0a6837, uuid:ab3b2803-5ffb-497e-8855-7bd5cf9adefb Format : application/pdf Producer : Adobe PDF Library 8.0 Trapped : False Page Count : 6 Creator : Adobe InDesign CS3 (5.0.2)EXIF Metadata provided by EXIF.tools