Greenheck Fan Grease Grabber H2O Auto Cleaning Hood Ggh20 Users Manual

Grease Grabber H2O Auto-Cleaning Hood GGH20 473380GGH2O_iom

GGH20 to the manual 8b132d06-652c-4c26-999c-13c8794c5944

2015-02-09

: Greenheck-Fan Greenheck-Fan-Grease-Grabber-H2O-Auto-Cleaning-Hood-Ggh20-Users-Manual-562563 greenheck-fan-grease-grabber-h2o-auto-cleaning-hood-ggh20-users-manual-562563 greenheck-fan pdf

Open the PDF directly: View PDF .
Page Count: 28

Download
Open PDF In Browser	View PDF

Part #473380
Grease Grabber™ H2O
Auto-Cleaning Hood

Installation,
Installation,
Operation
Operation and
and Maintenance
Maintenance
ManualManual
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the
product described. Protect yourself and others by observing all safety information. Failure to comply with instructions
could result in personal injury and/or property damage! Retain instructions for future reference.

Model GGH2O

General Safety Information
Only qualified personnel should install this unit.
Personnel should have a clear understanding of these
instructions and should be aware of general safety
precautions. Improper installation can result in electric
shock, possible injury due to coming in contact with
moving parts, as well as other potential hazards. Other
considerations may be required if seismic activity
is present. If more information is needed, contact a
licensed professional engineer before moving forward.
1. Follow all local electrical and safety codes, as well
as the National Electrical Code (NEC), the National
Fire Protection Agency (NFPA), where applicable.
Follow the Canadian Electric Code (CEC) in
Canada.
DANGER
Always disconnect power before working on or
near a unit. Lock and tag the disconnect switch or
breaker to prevent accidental power up.
CAUTION
When servicing the unit, motor may be hot enough
to cause pain or injury. Allow motor to cool before
servicing.

Model GGH20 Grease Grabber Auto-Cleaning Hood

Receiving
Upon receiving the product check to make sure all
items are accounted for by referencing the bill of
lading to ensure all items were received. Inspect
each crate for shipping damage before accepting
delivery. Notify the carrier if any damage is noticed.
The carrier will make notification on the delivery
receipt acknowledging any damage to the product.
All damage should be noted on all the copies of the
bill of lading which is countersigned by the delivering
carrier. A Carrier Inspection Report should be filled out
by the carrier upon arrival and the Traffic Department.
If damaged upon arrival, file claim with carrier. Any
physical damage to the unit after acceptance is not
the responsibility of Greenheck Fan Corporation.

Unpacking
Verify that all required parts and the correct quantity
of each item have been received. If any items are
missing, report shortages to your local representative
to arrange for obtaining missing parts. Sometimes it
is not possible that all items for the unit be shipped
together due to availability of transportation and truck
space. Confirmation of shipment(s) must be limited to
only items on the bill of lading.

The unit should be stored at least 3½ in. (89 mm) off
the floor on wooden blocks covered with moisture
proof paper or polyethylene sheathing. Aisles between
parts and along all walls should be provided to permit
air circulation and space for inspection.

Inspection and Maintenance during Storage
While in storage, inspect once per month. Keep a
record of inspection and maintenance performed.
If moisture or dirt accumulations are found on parts,
the source should be located and eliminated.

REMOVING FROM STORAGE — As units are removed
from storage to be installed in their final location,
they should be protected and maintained in a similar
fashion, until the equipment goes into operation.
Prior to installing the unit and system components,
inspect the unit assembly to make sure it is in working
order.

Handling
Units are to be rigged and moved by the lifting
brackets provided or by the skid when a forklift is
used. Location of brackets varies by model and size.
Handle in such a manner as to keep from scratching
or chipping the coating. Damaged finish may reduce
ability of unit to resist corrosion.

Storage
Units are protected against damage during shipment.
If the unit cannot be installed and operated
immediately, precautions need to be taken to prevent
deterioration of the unit during storage. The user
assumes responsibility of the unit and accessories
while in storage. The manufacturer will not be
responsible for damage during storage. These
suggestions are provided solely as a convenience to
the user.
The ideal environment for the storage of units and
accessories is indoors, above grade, in a low humidity
atmosphere which is sealed to prevent the entry of
blowing dust, rain, or snow. Temperatures should
be evenly maintained between 30°F (-1°C) and
110°F (43°C) (wide temperature swings may cause
condensation and “sweating” of metal parts). All
accessories must be stored indoors in a clean, dry
atmosphere.
Remove any accumulations of dirt, water, ice, or snow
and wipe dry before moving to indoor storage. To
avoid “sweating” of metal parts allow cold parts to
reach room temperature. To dry parts and packages
use a portable electric heater to get rid of any
moisture build up. Leave coverings loose to permit air
circulation and to allow for periodic inspection.
2

Model GGH2O

Table of Contents
Grease Grabber™ H2O System Function..................... 3
Cleaning Cycle
Manual and Automatic Engagement......................... 4
Fire Mode....................................................................... 4
System Components
Hood........................................................................... 5
Grease Grabber H2O Control Cabinet....................... 5
Graphic Keypad......................................................... 5
Unpacking...................................................................... 6
Hood Widths and Base Weights................................... 6
Installation Overview
Filler Panels................................................................ 7
Back Supply Plenum.................................................. 7
Hood Hanging Height................................................ 8
Double Island Style.................................................... 8
Installing U-Channel Strip....................................... 8
Continuous Capture Plenum.................................. 8
Ductwork.................................................................... 9
External Supply Plenums...................................... 9-10
Supply Plenum Clip................................................ 9
Uni-Strut................................................................ 10
Threaded Rod....................................................... 10
Supply Duct Collar................................................... 10
UL Listed Fastener................................................... 11
Back Supply Plenum........................................... 11-12
Supply Duct Collar................................................ 11
Hanging the Back Supply Plenum.................. 11-12
Hanging the Hood................................................. 12
Air Diffusers.............................................................. 12
Enclosure Panels...................................................... 13
End Skirts................................................................. 13
Backsplash Panels................................................... 14
Duct Collar................................................................ 15
Plumbing
Pump Installation..................................................... 16
Connections............................................................. 16
Detergent Tank......................................................... 17
Electrical
Wiring........................................................................ 17
Timer Programming – 24 Hour / 7 Day
Programming / Operation........................................ 18
Initial System Start-Up................................................ 19
Sequence of Operation............................................... 20
Airflow Testing Procedure........................................... 21
Wiring Schematic
Amerex®................................................................... 22
Ansul®...................................................................... 23
Wiring Diagram......................................................... 24
Maintenance
Filters........................................................................ 25
Floats........................................................................ 25
Troubleshooting........................................................... 26
Replacement Parts...................................................... 26
Grease Grabber H2O Start-Up Checklist.................... 27
Maintenance Log............................................Backcover
Warranty..........................................................Backcover

Grease Grabber™ H2O System
Function
Greenheck GGH2O hoods are designed for three
primary functions:
• Capture and contain the effluent produced by the
cooking process.
• Remove grease and other contaminants from the
airstream with two stages of mechanical filters
(Primary Grease X-Tractor filters and secondary
Grease Grabber filters).
• Wash the filters and other surfaces within the
exhaust plenum to remove contaminants.
NOTE
The wash sequence of the hood is not designed for
fire suppression and will not engage in the event of
a fire.
NOTE
The functions listed above require the control center
to be wired to the exhaust fan(s) and the hood
plumbed.
NOTE
For a complete list of functions, please refer to the
sequence of operations.

Normal Exhaust Operation and
Contaminant Collection
The system’s exhaust fan is manually controlled by
a press-button switch (FAN ON/OFF) on the graphic
keypad (included with hood). The exhaust system
operates until the FAN ON/OFF button is pressed. The
wash cycle can be manually engaged to run on a preprogrammed control sequence by pressing the CLEAN
HOOD button or automatically engaged to run at the
same time each day through a programmable timer.

Model GGH2O

Cleaning Cycle

Fire Mode

Manual Engagement

In the event of a fire, the hood exhaust fan(s) will turn
on at full power and the supply fan will turn off (default
setting controlled by others) regardless of current fan
operation. If the hood is in a wash cycle, the hood will
drain and the fans will turn on.

The wash function is triggered by pressing the Clean
Hood button after the exhaust fans are shut down at
the end of each day’s cooking operations (pressing
the Fans On/Off button).
Hot water and detergent will fill the hood reservoir.
The soapy water will then be cycled through the hood
by the attached recirculation pump, cleaning both the
filter banks and the exhaust plenum area on a timed
cycle.

NOTE
The wash sequence of the hood is not designed for
fire suppression and will not engage in the event of
a fire.

When the cleaning cycle is complete, the water
is purged from the reservoir by the pump and the
reservoir will again fill with clean hot water.
A rinse cycle will then run on a timed cycle and the
water will again be purged by the pump.
When the cycle is complete, the controller runs the
exhaust fans briefly to remove steam and excess
moisture from the exhaust system.

Automatic Engagement
The hood is equipped with an automatic timer. The
timer will automatically initiate the wash sequence
at the programmed time each day. All other washing
functionality will be the same as the manual
engagement sequencing.

Model GGH2O

System Components
Hood
The hood is shipped from the factory pre-piped and
ready to install. All wash components within the hood
are complete and ready for connection to hot water,
sanitary sewer drain and the electrical sources. Wiring
from the control panel to the hood (for lights) is by
Greenheck. All plumbing and wiring must conform to
plumbing and electrical codes. Duct collars are factory
mounted unless specified otherwise.

Graphic Keypad
The graphic keypad is the interface between the
control functions of the GGH2O hood and the user.
This keypad is typically mounted on the Grease
Grabber H2O control cabinet, but can also be shipped
loose for remote mounting. The keypad consists
of three main buttons: hood lights, fan on/off and
clean hood. The keypad also has system fault and fill
detergent indicator lights to alert of any fault in the
system or when the detergent tank is low.

NOTE
Filters are shipped loose with the hood and installed
in the field. See page 25 for installation details.

Grease Grabber H2O Control Cabinet
The control cabinet contains all of the water and
electrical components, and connections including
the Programmable Logic Controller (PLC), that
controls the wash sequencing and operations. The
control cabinet also includes the detergent reservoir,
detergent pump, recirculation pump, solenoid valves
and other water piping.
NOTE
he recirculation pump is shipped loose with the
T
hood. See pages 16 for installation details.

HOOD
LIGHTS

FAN
ON/OFF

HOOD
LIGHTS

FAN
ON/OFF
FAN
100%

CLEAN
HOOD

CLEAN
HOOD
SYSTEM
FAULT

FILL
DETERGENT

After pressing “CLEAN HOOD”, Fans will automatically stop.

SYSTEM
FAULT

FILL
DETERGENT

472619

After pressing “CLEAN HOOD”, Fans will automatically stop.

In case of emergency, the wash cycle can be stopped by pressing “CLEAN HOOD”.

472620

In case of emergency, the wash cycle can be stopped by pressing “CLEAN HOOD”.

GGH2O Keypad

GGH2O and Vari-Flow Keypad

NOTE
If the GGH2O is being used with the Vari-Flow Air
Management system, there will be an additional
FAN 100% button for sending fan speeds to 100%.
For detailed information on the Vari-Flow Air
Management system, please refer to the Greenheck
website, www.greenheck.com

LIGHTS

FANS

LUCES

VENTILADORES

100%
RESET

CLEAN
HOOD
FILL
DETERGENT

CLEAN
SYSTEM
FAULT

SETUP

FAULT
HOOD

%
After pressing “CLEAN HOOD”, Fans will automatically stop.
In case of emergency, the wash cycle can be stopped by pressing “CLEAN HOOD”.

Melink Customer Service USA: 877-477-4190

Listed 33 x 7

GGH2O and Melink® Intelli-Hood® Keypad

NOTE
If the GGH2O is being used with the Melink IntelliHood system, there will be two keypads. The Melink
Keypad will control the fans and lights. The GGH2O
Keypad will control the wash system.
NOTE
For information on PLC programming, please
consult the factory.

Model GGH2O

Skid

Front Lifting

Unpacking
Skid

Hood Width and Base Weights

Front Lifting
Skid

Profile of Hood
Profile of Hood

Remove side, back
and top lumber.
Remove 3-inch
lag screws while
holding the front
lifting skid in place.

Profile of Hood

Hood Width

Base Weight
without Water

Base Weight
with Water

inches
(cm)
48
(121.92)

lbs.
(kg)
440
(199.58)

lbs.
(kg)
488
(221.35)

51
(129.54)

449
(203.66)

497
(225.44)

54
(137.16)

457
(207.29)

505
(229.06)

57
(144.78)

465
(210.92)

513
(232.69)

60
(152.40)

474

522

1
1
63

When front lifting
skid is detached,
position it in front
of bottom skid.

Remove side, back and top lumber.
(215.00) and top lumber.
(236.78)
Remove
Remove side,
3-inchback
lag screws.
Remove
3-inch
lag
screws.
531
Holding the 483
front lifting skid in
Holding
the
front lifting
skid in
in (240.86)
(160.02)
(219.09)
place and
position
the skid
place
and
position
the skid in
front of
bottom
skid.
66
491
539
front of side,
bottom
skid.
Remove
back
and top lumber.
(167.64) Remove 3-inch
(222.71)
(244.49)
lag screws.
69
499 lifting skid in
547
Holding the front
(175.26) place and position
(226.34) the skid in (248.12)
side,
back and top lumber.
frontRemove
of bottom
skid.
72
Remove 508
3-inch lag screws. 556
(182.88)
(230.43)
Holding
the front lifting skid (252.20)
in
place and position the skid in
Base weight is based on 48 inches (121.92 cm) hood
front of bottom skid.

Profile of Hood
Profile of Hood

Profile of Hood

Carefully rotate
the hood as
shown.
Profile of Hood
Profile of Hood

length. For each additional foot of hood in length, add
55 lb/ft (24.95 kg/m) in weight of hood and 67 lb/ft
(30.39 kg/m) in weight of hood filled with water.
Example of a 10 foot hood:
Dry:

48 inch width x 120 inch length
= 440 lbs. + (6 ft. x 55 lb/ft)
Carefully
rotate
hood
=Carefully
440 lbs.
+ 330
lbs.
as shown.rotate hood
=as770
lbs.
shown.

With Water: 48 inch width x 120 inch length
= 488 lbs.
+ hood
(6 ft. x 67 lb/ft)
Carefully
rotate
=
488
lbs.
+
402
lbs.
as shown.
= 890 lbs.

Profile of Hood

Carefully slide the

The maximum weight (weight with water) should be
used for the maximum weight of the hood to ensure
the ceiling structure can support the weight of the
hood when filled with water.
CAUTION

Profile of Hood
hood onto the lifting

Profile of Hood
Profile of Hood

skid. The lifting skid
should be used to lift
the hood into its final
position. If the lifting
skid is not used,
the hood will be
damaged during the
installation process.

To ensure proper structural support, all hanger
brackets must be used for hanging the hood.

Carefully slide the hood
Carefully
slide the
hood
onto the lifting
skid.
onto the lifting skid.

3
3

Profile of Hood

Model GGH2O

Carefully rotate hood
DANGER
as shown.

The lifting skid should be used to
The
lifting
skid
should
be used
to
life the
hood
into
it’s final
position.
life
thelifting
hood
into
it’s
final
position.
Carefully
slide
theishood
If the
skid
not
used,
the
If
thethe
lifting
is not used,
onto
lifting
skid.
hood
will
beskid
damaged
duringthe
the
hood
will beprocess.
damaged during the
installation
installation
process.
The
lifting skid
should be used to
Carefully
slideit’s
the
hood
life the
hood into
final
position.
theskid
lifting
skid.
If theonto
lifting
is not
used, the
hood will be damaged during the
The lifting
skid should be used to
installation
process.
life the hood into it’s final position.
If the lifting skid is not used, the

Installation Overview

NOTE

Filler Panels
1. Unpack the hood and lay it on the lifting skid.
2. Bolt the filler panels together with 5/16 in. bolts
provided in the hardware package.
3. Position the filler panels to the hood back, and
tack-weld them into place.
4. To allow for ease of cleaning, caulk the external
seams with NSF Approved silicone caulk
(GE SCS1000, or its equivalent). The caulk is not
provided.
Hood

Hood

If you have a Back Supply Plenum (BSP), this must
be installed before the hood. Refer to page 11 for
instructions on installing the BSP.
NOTE
All hanger brackets must be used and the hood
must be properly supported while lifting to prevent
damage or distortion to the hood. The hood must be
hung level to operate properly.
After the hood is secured, make the exhaust duct
connections. The fire system distributor must be
contacted at this time. After the fire system has been
installed, mount the enclosures, then the supply
plenums. If an Horizontal Supply Plenum is provided,
it should be installed before the enclosures. The hood
and accessories are now installed.
Finally, make the electrical connections from the
controls to the fans and complete the fire system
circuits as required by the job specification (job
specific wiring diagram located inside the cabinet
cover).

Hood

Right Filler Panel
Tack-welded to
hood back

Bottom Filler Panel

5/16 inch x 3/4 inch bolts
with washers and nuts

Model GGH2O

Hood Hanging Height
The hood hanging height is critical. Hanging the hood
at the incorrect height may significantly reduce the
ability for the hood to function properly and may be in
violation of codes. The hood hanging height (typically,
78 in. (198.12 cm) above the finished floor) is given on
the UL label located on the inside of the hood on the
end panel. The hood must be hung level to operate
properly.
NOTE
Before hanging the hoods, please verify the hood
marks to make sure the correct hood is hung on the
correct side.

NOTE
The installation of the canopy hoods shall be
in accordance with NFPA 96 (latest edition),
Standard for Ventilation Control & Fire Protection of
Commercial Cooking Operations.
NOTE
Greenheck does not recommend walking or
standing on the hood top as damage can result. If
you must walk on the hood top, protect the hood
with additional support or planks for flooring.

Continuous Capture Plenum Hoods
1. Remove support angle on open end panel.
2. Raise all hoods into appropriate location and support per construction plans.
3. Fasten top angles together using 1/4 in. bolts and nuts (by others).
4. Fasten hoods together using u-clips, 1/4 inch bolts and cap nuts as indicated.
5. Caulk all seams as necessary.

Remove the support angles on the open end panels.
Use the installation procedure described for single
Double Island Style Hoods
island hoods; install and level both hoods. After
A double island hood is created by installing two
leveling,
the hoods together by tack-welding
1. Remove support
angle on secure
open end panel.
wall style hoods back to back. Use the installation 2. Raise all hoods into appropriate location and support per construction plans.
and/or
bolting
the
top
Fasten the hoods
Fasten top angles together using 1/4 in. bolts
andangles.
nuts (by others).
procedure for single island hoods; install and level 3.
4. Fasten hoods
together using
u-clips,u-clips
1/4 inch bolts
and cap
nuts asCaulk
indicated.this joint with
together
using
and
bolts.
5. Caulk all seams as necessary.
both hoods. After leveling, secure the hoods together
NSF Approved silicone caulk (GE SCS1000 or its
by tack-welding and/or bolting the rear mounting
equivalent). The caulk is not provided.
brackets. Caulk this joint with NSF Approved silicone
caulk (GE SCS1000 or its equivalent). The caulk is not
t
provided.
ron
1. After the hood is hung in position and leveled,
apply caulk to the inside edge of the double island
clip.

2. Position and install the clip by tapping into
veled…
ble island clip. position along clip (friction fit).
nto position along clip (friction fit).
3. ofCaulk
edges to seal out grease and allow for
allow for ease
cleaning.

ease
of cleaning. Caulk with NSF Approved silicone
caulk, GE SCS1000, or its equivalent. The caulk is
Installation Instructions.
not provided.

o
Ho

n
Fro
d
o
Ho

t
ron
dF

Hood

n
Fro
d
o
Ho

Caulk
1. After hood is hung in position and leveled…
Bolt
2. Apply silicone caulk to inside of double island clip.
3. Position and install clip by tapping into position along clip (friction fit).
4. Caulk edges to seal out grease and allow for ease of cleaning.
1B
do
o
H

Caulk

od
Ho

-1 A
od
Ho

nt
Fro

Hood-1A

Hood-1B

Double Island Clip

od
Ho

Installing U-Channel Strip

Silicone Caulk

Bolt

Hood

Acorn Nut

U-Clip

Acorn Nut

NOTE

U-Clip

• For multiple hood systems that have more than
14 lights total (incandescent
or fluorescent), the
-1B
od
hood lights must be
Howired to multiple circuits.
Each circuit must have less than 14 lights total.
-1 A

d
oStandard
• Light bulbs are not provided.
light bulbs
Ho
nt
up to 100 watts may be used.
o
r
F

od
Ho

Double Island Clip

DETAIL A

Model GGH2O

Ductwork

Installing External Supply Plenums

Exhaust

Option #3
Threaded Rod
supplied by others

Option #2
Uni-Strut supplied by others

As specified in NFPA 96, Ch. 7.5 (latest edition),
Threaded Rod
exhaust duct systems must be constructed in the
following manner:

Materials: Ducts shall be constructed of and
supported by carbon steel not less than 1.37 mm
(0.054 in.) (No. 16 MSG) in thickness or stainless steel
not
less
Option
#2 than 1.09 mm (0.043 in.) (No. 18 MSG)
uni-strut (U channel) that holds the hood up,
inThe
thickness.
cantilevers over the end of the hood and is
mounted to the Air Curtain Supply Plenum (ASP)
hanger brackets

Installation: All seams, joints, penetrations, and duct
to hood collar connections shall have a liquid‑tight
external weld. If you have an Automatic Fire Damper
please refer
that manual for installation instructions
ENDto
VIEW
now.

TOP VIEW
HOOD
Option #1
For plenums < than or = 96 inches
Two (2) clips are needed.
For plenums > than 96 inches
Three (3) clips are needed.

Hanging
methods for supply plenums
UTILITY
ASP: Air Curtain Supply Plenum
FSP: CABINET
Face Supply Plenum
VSP: Variable Supply Plenum

The third clip is located in the
center of the plenum length.

Option #1: Hanging Clip
Option #2: Uni-Strut
Option #3: Threaded Rod

Option #1
Attach hanging clip to hood
standing seam with the
supplied ‘C’ clamps.
Optional: Drill and bolt a
1/4-20 SS bolt through the
clip and hood standing seam

Supply
Supply ductwork
(where applicable) should be
Hood
connected to the hood in a manner approved by the
local code authorities.

11.5

For proper installation of duct collars when they are
Option #1 : Hanging
Clip
shipped
unattached see Installing Duct Collars on
Hood Standing Seam
‘C’ Clamp page 10.

TOP VIEW
SUPPLY PLENUM

23.5

Hanger Bracket

Option #3
Threaded Rod
supplied by others

Hanging Clip bolted to plenum shell

NOTE

For hoods with fire dampers in the exhaust and
supply duct collars, an access panel for cleaning
and inspection shall be provided in the duct. This
panel shall SUPPLY
be as close
to the SHELL
hood as possible but
HOOD FRONT
PLENUM
should not exceed 18 in. (45.72 cm).

Threaded Rod
Option #1
Hanging clip could be 23.5 inches from end if there is a utility cabinet on the
end of the hood.

Using the Supply Plenum Clip - Option #1
1. Bolt the hanging clip to the supply plenum. Two
clips are needed
Option #2 for plenums less than 96 in.
The long
uni-strutand
(U channel)
that holds
hood up, greater
(243.84 cm)
three
for the
plenums
cantilevers over the end of the hood and is
to the cm).
Air Curtain
Supply Plenum (ASP)
than 96 in.mounted
(243.84
The
hanger brackets
third clip is
located in the
center of the plenum length.
If there is a utility cabinet,
VIEW
the hanging clip END
should
be
23.5 in. (59.69 cm) from the
Supply Plenum Clip
end to the hood.
2. Using the c-clampsHood
provided, clamp the supply
plenum hanging clip to the hood standing seam.
Option: Drill and bolt a 1/4-20 SS bolt through the
clip and hood standing seam.
1.000

2.125

Form Up 57°

3.000

te: Supply plenums are standardly supplied with hanging clips (Option #1).
If Option #1 is not applicable, use Options #2 or #3

1.375

0.750

0.625

.500 x .375
SLOT (3 PLACES)

0.563

Form Down 147°

Hanging Clip

1.000

1.500

1.000

0.625

0.563

0.750

4.500

HANGING CLIP

2.120

1.000

147.0°

57.4°

SUPPLY PLENUM SHELL

HOOD FRONT

Option #1 : Hanging Clip
‘C’ Clamp

Hood Standing Seam
Hanging Clip bolted to plenum shell
Hanging Clip

HOOD FRONT

SUPPLY PLENUM SHELL
NOTE

Note: Supply plenums are standardly supplied with hanging clips (Option #1).
The
supply
is provided
with
If Option
#1 isplenum
not applicable,
use Options #2
or #3plenum clips

that assist in hanging the plenum. The plenum
should not be hung only with the plenum clips;
threaded rod or uni-strut must also be used.

Model GGH2O

BACKSUPPLY CANOPY STYLE HOOD

BACKSUPPLY BACKSHELF HOOD

Using the Uni-Strut - Option #2

Using the Threaded Rod - Option #3

1. The uni-strut (supplied by others) that holds the
hood up cantilevers over the end of the hood and
is mounted to the supply plenum hanger brackets.

1. Insert 1/2 in. (12.7 mm) diameter threaded rod (by
others) into hanger brackets on the supply plenum
top. Raise and hang the external supply plenum
Option #2
from adequate roof or ceiling
supports.

Option #3
Threaded Rod
supplied by others

Threaded Rod

UPPLY CANOPY STYLE HOOD

Uni-Strut supplied by others

2. The external supply plenum
should be resting
TOP VIEW
lightly against the hood. TheHOOD
hood is used to
position the plenum only, it is not intended to
Option #1
supportBACKSHELF
the plenum.
hanger brackets must be
BACKSUPPLY
HOODAll
For plenums < than or = 96 inches
Two (2) clips are needed.
used and the plenum must
be properly supported
For plenums > than 96 inches
while
lifting
to
prevent
damage
distortion. The
Three
(3) clips are or
needed.
UTILITY
Thehung
third clip islevel
located into
the operate
supply
plenum
must
be
CABINET
center of the plenum length.
properly.

BACKSUPPLY CANOPY STYLE HOOD

Option #2
The uni-strut (U channel) that holds the hood up,
cantilevers over the end of the hood and is
mounted to the Air Curtain Supply Plenum (ASP)
hanger brackets

Hanger Bracket

END VIEW

Hood

Duct cut out area
Hood Standing Seam

‘C’ Clamp

Option #1 plenum to hood. See
(Optional fastening of supply
Attach hanging clip to hood
directions).
standing seam with the
supplied ‘C’ clamps.

Exhaust Plenum
VARIABLE SUPPLY PLENUM CANOPY STYLE HOOD

Option #1 : Hanging Clip

3.0

Exhaust Duct
Optional: Drill
bolt a
3. It is recommended that caulk
beandapplied
at the
Connection
1/4-20 SS bolt through the
clip and of
hoodthe
standing
seam
mating seams and surfaces
plenum,
the
14.0
ATTACHED AIR CURTAIN CANOPY STYLE HOOD
ATTACHED AIR CURTAIN CANOPY STYLE HOOD
hood, and the
wall. If the supply plenum is next
to a wall,11.5you will also need to caulk
around
the is to be
Exhaust
duct connection
liquid-tight weld to hood.
surface next to the wall. Caulk
thea continuous
joints with
Hood
TOP VIEW
23.5
Width
NSF Approved
siliconeSUPPLY
caulk (GE
SCS1000, or its
PLENUM
equivalent). The caulk is not provided.
Hanger Bracket

Installing the Supply Duct Collar to the
Plenum
Option #1

Hanging Clip bolted to plenum shell

3.0

Hanging Clip

clip could be 23.5 inches from end if there is a utility cabinet on the
1. Hanging
Place
the duct collar(s) over the opening, fastening
end
of the hood.
with
tack-welds
at 1 to
2 in.
(2.54 to 5.08 cm)
ATTACHED AIR CURTAIN CANOPY
STYLE
HOOD
intervals, or sheet metal screws at 3 to 6 in.
(7.62 to 15.24 cm) intervals.

Front ofATTACHED
Hood
UPPLY PLENUM CANOPY STYLE HOOD
AIR CURTAIN CANOPY STYLE HOOD
8.0
Variable
Supply
Plenum
SUPPLY
PLENUM
SHELL
HOOD
FRONT
Hood Length

(HSP or VSP)

Note: Supply plenums are standardly supplied with hanging clips (Option #1).
If Option #1 is not applicable, use Options #2 or #3

Supply Duct
Connection

8.0

Top of Hood

Supply duct connection to be
tack-welded with 1 to 2 inch
tacks or sheet metal screws
at 3 to 6 inch spacing to hood.

Exhaust Plenum

Duct cut out area

Air Curtain Supply Plenum
(ASP)

External Supply Plenum Weights, Dimensions and Supply Rates

in inches.

Weight
Width
External Supply
Plenum Type
o be located within 48 inches from center of hood length
to center of(kg/ft)
duct connection.
(lbs/ft)
(in)
(mm)

Height
(in)

o be used only with Greenheck Fan Corp. labelled subassembly for exhaust hood without exhaust damper part no. DC

(mm)

Back Supply

35.0

15.878

152.4

Air Curtain Supply
• 14 inch

9.5

4.31

355.6

254

Air Curtain Supply
• 24 inch

12.5

5.67

609.6

254

Variable Supply

Horizontal Supply

10 Model GGH2O

16.0

14.0

7.26

6.35

304.8

Length per
section
(ft)

457.20

(m)
.91 to
4.88

145 cfm/ft
(246.36 m3/hr)

3 to 16

.91 to
4.88

110 cfm/ft
(186.89 m3/hr)

3 to 16

.91 to
4.88

145 cfm/ft
(246.36 m3/hr)

3 to 16

.91 to
4.88

Variable Variable 3 to 16

Recommended
Supply Rate

3 to 16

.91 to
4.88

curtain

0-80 cfm/ft
(0-135.92 m3/hr)

face

80-160 cfm/ft
(135.92 -271.84 m3/hr)
150 cfm/ft
(254.85 m3/hr)

Using the UL Listed Fastener Provided
1. Drill a 9/32 in. hole for the 1/4 in. bolt from the
inside of the supply plenum to inside the hood.
Fasteners are to be located max.
6 in.1(15.24 cm)
STEP
from the end of the hood with
max.
(IF MODULEspacing
< 6 ft.)
between bolts 36 in. (91.44 cm)

DO NOT include utility cabinets or fillers when
figuring bolt placement.

DO NOT bolt the supply plenum to a fire/utility
cabinet.

3. If the back supply plenum is greater than 9 ft.
10 in. (299.72 cm) long, divide the length of the
back supply by four. This will give you the center
of each half. Cut STEP
openings1at the suggested
location, centering the duct collar over the center
(IF MODULE > 6 ft.)
measurement of each half.

L (MODULE LENGTH)
L/4

L (MODULE LENGTH)

L/2 and nut.
Hole size 9/32-inch
2. Push bolt through hole, attachL/2the washer

L/2

3. Hand tighten; then use a wrench until fully
tightened. Caulk around bolts from inside of hood
as necessary.

L/4

Hood

1/4 - 20 UNC - 2A
SS Bolt

1/4 inch SS Nut

PLAC
FASTE
4 in. T

SS Flat Washer

STEPCENTERED
1
ON WIDTH OF THE SUPPLY,

ON WIDTH over
OF THE
SUPPLY,
4. Place CENTERED
the duct collar(s)
the
opening, fastening
CUT (2) 4 in. X 24 in. OPENINGS AT
with screws
or
tack-welds
every
4 to 6 in. (10.16 to
THE SUGGESTED LOCATIONS ABOVE
15.24STEP
cm).
2

(1) 4 in. X 24 in. OPENING AT
(IF MODULE >CUT
6 ft.)
THE SUGGESTED LOCATION ABOVE
Installation instructions for the AC3 fastener:
Installing
the Back Supply Plenum
1) Create athe
9/32 Supply
in. hole for Duct
ºî bolt. Collar
Installing
2) Install bolt through hole.

L (MODULE LENGTH)

L/4 appropriate
Install
washer
(1/4 in.)
1. 3)Find
the center
of the
back supply plenum.
4) Install nut

use a wrench
untilis
tightened.
2. 7)IfHand
thetighten,
backthen
supply
plenum
less than 9 ft. 10 in.
L/2 STEP 1
(299.72 cm) long, cut
opening at the suggested
(IF MODULE
< 6 ft.) over the center of
location, centering
the opening
L/4
the back supply plenum.

STEP 1
(IF MODULE > 6 ft.)

L (MODULE LENGTH)
L/4
L/2

L/2

L (MODULE LENGTH)

The 4 in. (10.16 cm)
high duct collar is to
be attached to the
back supply.

L/2
PLACE THE DUCT COLLAR OVER THE OPENING,
the Back
Supply
Plenum
FASTENHanging
WITH SCREWS,
OR TACK
WELDS
EVERY
L/4
4 in. TO 6 in.

5. Hang the back supply plenum from the ceiling.

CENTERED ON WIDTH OF THE SUPPLY,
CUT (2) 4 in. X 24 in. OPENINGS AT
THE SUGGESTED LOCATIONS ABOVE

CENTERED ON WIDTH OF THE SUPPLY,
CUT (1) 4 in. X 24 in. OPENING AT
THE SUGGESTED LOCATION ABOVE

The back supply plenum needs to be mounted
31.25 in. (79.375 cm) above the floor (based
upon a canopy hood that will be hung at 78 in.
(198.12 cm) above the finished floor. This is
measured from the lowest rear edge of the back
supply plenum to the finished floor. Leave 6 to
PLACE THE DU
10 inches (15.24 to 25.4 cm) of space below theFASTEN WITH S
4 in. TO 6 in.
plenum for access to the air diffusers.

CENTERED ON WIDTH OF THE SUPPLY,
CUT (2) 4 in. X 24 in. OPENINGS AT
THE SUGGESTED LOCATIONS ABOVE

Model GGH2O 11

6. Fasten the back supply to the wall, going through
the lower back supply wall.

• These
fasteners
Canopy
Style
Hoodare to help maintain the location
of the Back Supply, and are not intended to hold
the weight of the back supply unit.

• The fasteners should not interfere with the
removable air diffusers.
• The 31.25 in. (79.375 cm) height is based upon
the canopy hood hanging height of 78 in.
(198.12 cm)
STEP 3

5. Connect the remaining ductwork for the back
supply and the hood. It is recommended that
caulk be applied at the mating seams and
surfaces of the back supply, the hood, and the
wall.

Air Diffusers
The air diffusers, located at the bottom of the back
supply, will need to be cleaned as often as the
application dictates. Inspect periodically to determine
the cleaning schedule.
Step 5 / Air Diffusers
1. To clean the air diffusers, unfasten the screws.
Furnished
by Others at an angle from the bottom.
a.Remove
Insert the
airair
diffusers
the
diffusers from the back supply
b.unit,
Rotate
diffusers
tehor
forms
are downward.
andthe
wash
in theso
sink
dishwasher.
0.500
in. Threaded
& internal angles.
c.
Rest
the
diffuser
on
the
2. Insert the0.500
air in.
diffusers
at an angle from the bottom,
Threaded Nuts
(Furnished by Others)
and rotate
so the forms are downward. Rest the
diffuser on the internal angles.

Hanger Bracket Detail

Removable Air Diffusers

1) Hang Backsupply Modules from the
ceiling (the example shows the module
being supported with threaded rod)
The backsupply is to be 31.25 in. from the
floor. This is measured from the lowest
rear edge of the backsupply module to the
finished floor.

Proximity Style Hood

3. Refasten
with
the stainless steel screws.
Canopy
Style
Hood
2) Fasten
backsupply to wall through the

Fasteners holding the
back supply to the wall

31.25 in.
Critical
Dimension

lower backsupply wall. These fasteners
are to help maintain location of the
backsupply, and are NOT intended to hold
any weight of the unit. Fasteners should
not interfere with the removable air diffuser.

Hanging the Hood

Step 5 / Ai
a. Insert th
b. Rotate t
c. Rest the

Before hanging the hood according to the hood
installation instructions, please check the following:
1. Make sure the back supply plenum is properly
secured, as described in steps 5 and 6.
2. If the ductwork for the back supply plenum will not
interfere with the hood installation, it should be
connected now.
3. Any filler panels should be attached to the hood
before the hood installation.
4. Lift the hood, and position it so the filler panels
are resting lightly on the top outside edges of the
back supply. The back supply is used to position
the hood only. It is not intended to hold any hood
CANOPY STYLE HOOD
weight.

Removable Air Diffusers

Proximity Style Hood

STEP 4
HANG THE HOOD
1. THE HOOD IS TO BE HUNG AS PER THE HOODS INSTALLATION
INSTRUCTIONS AND THE FOLLOWING.
2. BEFORE THE HOOD IS HUNG THE BACKSUPPLY MUST BE SECURED
PROPERLY, AS DESCRIBED IN "STEP 3 in.
3. DUCTWORK FOR THE BACKSUPPLY; IF IT WILL NOT INTERFERE,
SHOULD BE CONNECTED BEFORE THE HOOD IS HUNG.
4. LIFT THE HOOD; POSITION IT SO THE TOP OF THE
HOOD IS LEVEL WITH THE TOP OF THE BACKSUPPLY; AFTER
THE HOOD IS HUNG FROM THE CEILING AS PER IT'S INSTALLATION
INSTRUCTIONS, THE HOOD MAY BE FASTENED TO THE BACKSUPPLY.

12 Model GGH2O
EYEBROW STYLE HOOD

5. CONNECT REMAINING DUCTWORK FOR THE BACKSUPPLY AND THE
HOOD. CAULK IS RECOMMENDED TO BE APPLIED AT THE MATING
SEAMS/SURFACES OF THE BACKSUPPLY, THE HOOD, AND THE WALL.

Installing Enclosure Panels

Installing End Skirts

Before installing the enclosure panels, make sure
the hood is hung in position with all the ductwork
attached, electrical connections and fire system
connections completed.

1. After the hood is hung in position, slide the
hemmed form on top of the end skirt onto the end
panels of the hood.

1. Position the end enclosure panels on the hood,
and clamp into place with clamps provided or
tack-weld the panels into place.

2. Drill a hole in the hood end panel to line up with
the hole in the end skirt. Attach the end skirt with
a 1/4 in. bolt and cap nut to the inside of the hood,
or tack-weld the end skirt to the hood.

2. Fasten the end enclosure panels to the wall,
method depends on wall construction. (Fasteners
are not provided).

3. Position the end skirt against the wall and attach.
The method depends on the wall construction.
(Fasteners for this are not provided).

4. Caulk the internal joint formed by the end skirt and
the hood end panel with NSF Approved silicone
caulk (GE SCS1000 or its equivalent). The caulk is
not provided.

If the hood is a double island, bolt the end
enclosure panels together. (Fasteners are not
provided).

3. Position the front enclosure panel(s) on the hood,
and bolt to the end enclosure panels with the
5/16 in. bolts provided in the hardware package.

5. To allow for ease in cleaning, also caulk all the
external seams.

4. Tack-weld or clamp the front enclosure panel(s)
to the hood. If clamps are used, they must be
positioned 4 in. (100 mm) from the ends, and in the
center of the front enclosure panel.

HO
O

5. To allow for ease of cleaning, caulk the external
seams with NSF Approved silicone caulk
(GE SCS1000, or its equivalent). The caulk is not
provided.

ON
T

PA
N

Note: Installation instructions may not be applicable
for concrete ceilings.
Exploded
view
below

Bolt panels together with 5/16-inch bolts.
Supplied by mfg.

Full End Skirt

Hemmed Edge
Clamp panels to hood standing seam with hardware.

Supplied by mfg.

Attach to wall
Fasteners by others

End Enclosure
Panel
Front Enclosure Panel

Exploded View
Holes drilled by installer

HO
OD

End Enclosure
Panel

1/4-inch bolt and cap nut

Supplied by mfg.

Attach to wall.
Fasteners by others

Model GGH2O 13

Installing
Backsplash Panels
AT BACKSPLASH
PANEL

1. After the hood is hung in position, slide the flat
flange of the backsplash panel behind the back of
the hood.

RIAL GAUGE — STAINLESS

Flat backsplash panel
Material gauge – Stainless
LAT BACKSPLASH PANEL

Wall

ERIAL GAUGE — STAINLESS

Heigth

Wall

2. After the backsplash panel has been positioned,
drill holes in the panel and fasten to the wall.
(Fasteners provided by others).

Heigth

Note: If the backsplash panel length is greater
than 45 in. (114.3 cm), it will be shipped in multiple
pieces.

Note: The holes should be spaced to adequately
secure the panel to the wall.

3. Caulk the joints between the hood and the
backsplash panel with NSF Approved silicone
caulk (GE SCS1000, or its equivalent). The caulk is
not provided.

Length

4. Caulk the joint between the backsplash panels
when multiple panels are required, with NSF
Approved silicone caulk (GE SCS1000, or its
equivalent). The caulk is not provided.

Length

NOTE

ANELS UP TO 48 IN. (1219.2 MM) WIDE SHIP IN ONE PIECE; OVER 48 IN. (1219.2 MM) IN MULTIPLE PIECES.

Panels up to 47 inches (119.4 cm) wide ship in one
piece. Over 47 inches (119.4 cm) in multiple pieces.

Hood End Panel

Hood Front Panel

PANELS UP TO 48 IN. (1219.2 MM) WIDE SHIP IN ONE PIECE; OVER 48 IN. (1219.2 MM) IN MULTIPLE PIECES.

SULATED BACKSPLASH PANEL

RIAL GAUGE — STAINLESS
LATION — 1 IN. (25.4 MM)

Insulated backsplash panel 1 inch (25.4 mm)
Material
gauge – Stainless
NSULATED
BACKSPLASH
PANEL
Insulation – 1 inch (25.4 mm)
TERIAL GAUGE — STAINLESS

ULATION — 1 IN. (25.4 MM)

Wall
1 inch (25.4 mm)
Height
Wall
Slide flange
behind back
of the hood.

Height

Backsplash Panel
Section view of
backsplash panel
overlap

Length

ANELS UP TO 46 IN. (1168.4 MM) WIDE SHIP IN ONE PIECE; OVER 46 IN. (1168.4 MM) IN MULTIPLE PIECES.

Holes should be spaced
to adequately secure the
panel to the wall studs.
(Hole spacing and fasteners
provided by others).

PANELS UP TO 46 IN. (1168.4 MM) WIDE SHIP IN ONE PIECE; OVER 46 IN. (1168.4 MM) IN MULTIPLE PIECES.

NOTE

Panels up to 45 inches (114.3 cm) wide ship in one
piece. Over 45 inches (114.3 cm) in multiple pieces.

14 Model GGH2O

Installing Duct Collar
Overview of exhaust and supply plenum locations
TOP VIEW

Hanger Bracket

3.0
Exhaust Duct
Connection

Exhaust Plenum

14.0
Exhaust duct connection is to be
a continuous liquid-tight weld to hood.

Hood
Width

Duct cut out area

3.0

Front of Hood

8.0

Hood Length

8.0

BACK VIEW
8.0
1.0

12.0

Supply Duct
Connection

Top of Hood

8.0

Exhaust Plenum

Supply duct connection to be
tack-welded with 1 to 2 inch
tacks or sheet metal screws
at 3 to 6 inch spacing to hood.

Duct cut out area

Dimensions are shown in inches.

1. The exhaust duct connection needs to be located
within 48 in. (121.92 cm) from the center of the
hood length to the center of the duct connection.

NOTE: 1. Exhaust duct connection to be located within 48 inches from center of hood length to center of duct connection.
2. UL Listed hood assembly to be used only with Greenheck Fan Corp. labelled subassembly for exhaust hood without exhaust damper part no. DC

2. The exhaust duct connection is to be a continuous
liquid-tight weld. Weld with a non-ferrous filler
wire, such as silicon bronze or stainless steel filler
wire. Protect all stainless steel areas from weld
splatter.

Model GGH2O 15

Plumbing

Plumbing Connections

Once the hood is hung, the recirculation pump and
detergent tank (both shipped loose) must be installed
in the controls cabinet.

Pump Installation

• Remove bolts from pump mounting plate in cabinet.
• Place the pump on the isolators located on the
mounting plate with the bolts removed.
• Secure the pump to the mounting plate with the four
previously removed bolts.
• Wire pump motor to the control cabinet per wiring
diagram on the cabinet.
• The wires to power the motor are already connected
to the pump motor. It only needs to be wired to the
control cabinet.

Position pump on
(4) isolators and attach
using provided nuts.

A.
B.
C.
D.
E.

One-inch unions
Detergent tank
Mounting plate
Isolators (qty of four)
Detergent pump

1. Connect the inlet and outlet piping on the
recirculation pump to the respective piping in the
cabinet via the threaded 1 in. unions.

Connect to control
cabinet per
Wiring Diagram
in panel

1-inch female NPT
Connect to drain

Field
connect
1-inch
unions

2. Bring the inlet water piping to the connection
located on the top of the hood and connect to the
threaded connection on the 3/4 in. solenoid valve.
A ball valve needs to be placed in the connection
line before the 3/4 in. solenoid valve. Depending
on water pressure, the inlet valve might need to
be closed slightly to reduce water pressure. Water
temperature should be 140°F.
Inlet Solenoid
Connection

3. Bring the drain piping connection to the 1 in.
solenoid valve in the control cabinet and connect
to the threaded connection. This is a pressurized
drain system and needs a properly sized drain to
accommodate the pressurized drain water.
NOTE
As the suggested detergent is non-caustic and
biodegradable, waste water from the hood can be
drained in any typical grease trap.

16 Model GGH2O

Detergent Tank Installation
The detergent tank is located as shown in the photo.
When installing the detergent tank, the low detergent
indicator float and the detergent pump inlet tubing will
need to be lifted. Once the tank is in position, the low
detergent indicator float and detergent inlet tube must
be lowered into place inside the tank.

A. One-inch unions

B. Detergent tank

C. Mounting plate

D. Isolators (qty of four)

E. Detergent pump

Detergent Requirements
The detergent brand Formula G-510 (by 2010
Products, Inc.) is recommended by Greenheck for use
in the wash system. Use Formula G-510 full strength.
This product is biodegradable, non-caustic, and safe
for kitchen staff to use. If G-510 detergent is not
used, the cleanliness of the exhaust plenum and filters
cannot be guaranteed.

Preventative Maintenance
The following practices will prolong the life of the
detergent pump:

Electrical
Electrical Wiring
All wiring must be done according to NEC (National
Electrical Code NFPA #70) and local building codes.
Two sources of power need to be brought into
the electrical control cabinet. A 120 volt, 30 amp
service with 12 gauge wire needs to be connected
to terminals L1 on the disconnect switch and N. A
120 volt, 15 amp service with 14 gauge wire needs to
be brought into the electrical cabinet and connected
to terminal L2 on the disconnect switch and N1.
NOTE
The wash control station will provide a dry contact
for a fan starter so the fans can be controlled by the
PLC. The fan starter is not provided with the wash
control station.
The main recirculating pump needs to be wired after it
is installed in the hood. There are three 12 gauge wires
in flexible conduit wired to the pump. Wiring to the
pump is complete from the factory. The whip from the
pump needs to be wired into the control cabinet.

• Keep detergent tank filled.
• Avoid spilling detergent on the exterior of the
pump.
• Clean the detergent tank at least every six
months.
• Clean the detergent line strainer at least every six
months.
• Check tightness of all fittings periodically.
The detergent pump motor has sealed bearings which
do not require lubrication.
NOTE
G-510 is manufactured by 2010 Products, Inc., Food
Service Division, Salem, Oregon 97303. For details
and ordering information, call 800-286-2010.

Model GGH2O 17

Timer Programming –
24 Hour / 7 Day
Setting the Clock
1. Press and hold the CLOCK button.
2. Press and hold the DAY button until the display
shows the current day.
3. Press the HOUR button until the display shows the
current hour.
4. Press the MIN (minute) button until the display
shows the current minute.

Setting the Programs
1. Press the PROG (program) button once. You will
now set the time in which you want the wash to
start. The number 1 in the lower left hand corner
indicates that you are now programming Event 1.
2. Press the DAY button repeatedly until the display
shows the day(s) when you want the timer to turn
on. The options are:
- Days of the week
MO, TU, WE, TH, FR, SA, SU
- Individual days of the week
MO etc.
- Weekdays only
MO, TU, WE, TH, FR
- Weekends only
SA, SU
3. Press the HOUR and MIN (minute) buttons to set
the time when you want the timer to turn on.
4. Press the PROG (program) button again.
5. Repeat steps 2-4 to set the OFF time for Event 1.
This should be set one minute after the ON time.
6. When programming is complete, press the CLOCK
button to display the current time.
Things you should know about programming events:
• You can repeat the ON and OFF programming
procedures outlined above for up to seven (7)
events as needed.
NOTE
While setting events, the timer may prematurely turn
on the load, if you press the MODE button.
• Three kinds of settings can cause the timer to
work in an unexpected way:

a. Set up events in progressive order of time, for
example:

Reviewing Events Programmed
In your current time display, press the PROG (program)
button repeatedly to check your settings.
When finished, press the CLOCK button to return the
display to the time of day.

Clearing (Deleting an Event)
1. Press the PROG (program) button as many times
as necessary to locate the setting you want to
clear.
2. Press and hold the MODE button.
3. Press the PROG button to clear the setting.
4. When finished, press the CLOCK button to return
the display to the time of day.

Operating the Time Switch
Press the MODE button repeatedly to set the timer to
Automatic, Random or Manual mode.
NOTE
For the time switch to run programmed events, it
must be set to AUTO mode.
• AUTO runs all events automatically according to the
schedule you have set. The word AUTO appears in
the display.
• RND (random) runs all events in a RANDOM mode.
This is a security feature in which ON and OFF
times randomly differ +/- 15 minutes from the
programmed times, creating a more “lived-in” look.
The word RND appears on the display.
NOTE
Do NOT set this timer to RND mode. It will not wash
at the exact time you programmed.
• MANUAL turns ON and OFF only when the user
presses the ON or OFF button. The display is blank,
showing neither RND or AUTO.

Overriding Timer Settings
The ON or OFF buttons override the current
programmed events. To override the current program
(either ON or OFF), press the ON or OFF button.

8:00 pm ON, 9:00 pm ON, 10:00 pm ON
Not 8:00 pm ON, 10:00 pm ON, 9:00 pm ON

b. Do not overlap event times, for example:

8:00 pm ON / 12:00 pm OFF and
9:00 pm ON / 11:00 pm OFF

c. Set the OFF time for one minute after the ON
time.

18 Model GGH2O

Initial System Start-Up

Daily Operation of the GGH2O Hood

1. Check electrical power (see wiring diagram)
• Correct supply voltage
• Proper connections to fire
suppression system
2. Check to make sure the
disconnect switch on the
electrical control cabinet is
switched to the “ON” position.
3. Prime the recirculation pump. Remove the plug on
top of pump and use a funnel to add water to the
pump. This only needs to be done one time prior to
initial start-up.
4. Add detergent to the detergent tank in the cabinet.
5. Clean the control cabinet of any debris that may
have entered the cabinet during installation.
6. Close the cabinet doors and press the Fan On/Off
button.
7. Check the exhaust and supply air volumes.
8. Press the Fan On/Off button to turn the fans off.
9. Press the Clean Hood button.
When the hood is filling, check to ensure water is not
leaking through the edges of the access doors. If so,
the inlet water pressure is too high. Slowly close ball
valve located before the inlet solenoid on the hood top
until no water leaks pasT the access doors.

Pressing the FAN ON/OFF button will start/stop the
exhaust and supply fans if interlocked.
Pressing the HOOD LIGHTS button will turn on/off the
hood lights.

Initiating the wash cycle:
The Grease Grabber H2O has an automatic timer
that can be set to control the wash schedule and
automatically start the cycle. See Timer Programming
on page 18.
To initiate the wash cycle manually, press the CLEAN
HOOD button on the keypad. If you press this button
while the fans are running, the system will stop the
fans and then start the wash cycle. When the wash is
completed, the system will automatically reset itself.
If the fans are controlled by a building management
system (BMS), the steps above still apply unless a
special program is requested to bypass having to
initiate the wash cycle by pushing the FAN ON/OFF
and CLEAN HOOD buttons.
Refer to the Grease Grabber™ H2O Hood checklist
on page 27 for detailed instructions on start-up
operations.

After the hood fills with water and starts washing the
primary filters, open water valve slowly until water
mist is felt above equipment. Then slowly close valve
until water mist is no longer felt above equipment.
Once the valve is set it will not need to be moved
again.
Verify the Grease Grabber H2O sequence of operation
(see the diagram of wash sequence on page 20)
during the detergent pump cycle.
C
E
D

Interior of Cabinet
A.
B.
C.
D.
E.
®

Recirculating pump
Detergent tank
Water valve to adjust front primary filter nozzles
Pump plug for priming
Detergent pump
Model GGH2O 19

Shut OFF exhaust fan(s)

20 minute dry time

Stage 8:
Rinse primary filters
Detergent pump OFF

SEQUENCE OF OPERATION - GREASE GRABBER H2O
Turn OFF exhaust fan(s)

Stage 1:
Fill hood tank (hot water)

Sequence of Operation - Grease Grabber™ H2O
Spray for 5 minutes

Stage 2:
WASH filters
Wash primary
Detergent pump ON

RINSE
Stage 9:
Rinse secondary filters
Detergent pump OFF
Stage 7:
Fill hood tank (hot water)

Hot Water Recovery:
(0
min.)for
Adjustable
Spray
5 minutes

Wash, rinse & dry complete
DRY

Turn ON exhaust fan(s)

Spray for 5 minutes
Shut OFF exhaust fan(s)
Stage 3:
Wash secondary filters
Detergent pump ON
Stage 1:
Fill hood tank (hot water)

20 minute dry time

Stage 8:
Rinse primary filters
Stage
10: OFF
Detergent
pump
Drain rinse water

Turn OFF exhaust fan(s)

Spray for 5 minutes

Wash, rinse & dry complete

Stage 2:
Wash primary filters
2
minute
delay ON
for
Detergent pump
water settling

Stage 9:
Rinse secondary filters
Detergent pump OFF

Spray for 5 minutes
Stage 4:
Wash primary filters
Detergent pump OFF
Stage 3:
Wash secondary filters
Detergent pump ON
Spray for 5 minutes

Spray for 5 minutes

Stage 10:
Drain rinse water

Spray for 5 minutes
Stage 5:
Wash secondary filters
Detergent
2 minutepump
delayOFF
for
water settling

Spray for 5 minutes
Stage 4:
Wash primary filters
Detergent
pump
Stage
6: OFF
Drain soapy/dirty water
Spray for 5 minutes

Stage 5:
Wash secondary filters
Detergent pump OFF

Spray for 5 minutes

Stage 6:
Drain soapy/dirty water

NORMAL FAN OPERATION

Normal Fan Operation
Exhaust Mode in Fire -- RUN

Exhaust Mode in Fire -- STOP

START FAN

Fan(s) will run

Fan(s) will run
No

FIRE

Temperature Interlock
Fan(s) OFF

No
NORMAL FAN OPERATION

Temperature
> 95°F.
(Adjustable)

FIRE

Yes

Exhaust Mode in Fire -- RUN

Exhaust Mode in Fire -- STOP

Exhaust
Fan(s)
STARTremain
FAN
ON

Exhaust
Fan(s) FAN
will
START
turn OFF

Fan(s) will run

20 Model GGH2O

Exhaust Fan(s)

Temperature
Interlock
will turn ON
Fan(s) OFF

Temperature
> 95°F.

Airflow Testing Procedure
After the appropriate number of readings have been
taken from the inlet slot of the hood, an average
reading can be calculated by summing the velocity
readings and dividing the total value by the number of
readings taken.
Average Velocity

Sum of Velocity Readings
Number of Readings

Next calculate the total hood airflow volume (CFM) by
using the following equation:
Hood CFM = [(Length of Hood in inches x 4.846) x
(Average inlet slot velocity x 2.47)]  144
NOTE
The constants 4.846 and 2.47 are factory derived for
use with the Grease Grabber™ H2O.

Calculation Example:
Five (5) inlet slot velocity readings (minimum)
Short Ridge Meter Components

For measuring exhaust airflow rates (cubic feet per
minute = CFM), use a short ridge meter to measure
velocities along the inlet slot of the hood. To ensure
accurate data, all appliances should be on. Multiple
locations need to be tested as outlined below to
ensure an accurate reading.
Hood Length

48 to 72
inches

Minimum Number
of Test Locations

72 to 120 120 to 192
inches
inches
5

Hood Length

96 inches

Test Location
(off left; in inches)

Velocity Reading (fpm) 175

210

250

190

160

Average Velocity (FPM) =

(175 + 210 + 250 + 190 + 160)  5 = 197 FPM
Hood Exhaust Rate (CFM) =

[(96 x 4.846) x (197 x 2.47)]  144 = 1572 CFM

To take velocity readings along the length of the hood,
the edge of the short ridge meter must start/stop six
(6) inches from the end of the hood. Vertical placement
of the short ridge meter along the inlet is shown.

Model GGH2O 21

Amerex® Wiring Plan View
POWER SOURCE

MANUAL RESET RELAY

PRM
ELECTRIC GAS VALVE

MICROSWITCH

INSTALLER PROVIDED JUNCTION BOXES

BASIC WIRING DIAGRAM
POWER SOURCE
MANUAL RESET RELAY
RED (COMMON)

YELLOW (N.O)
BLACK (N.C.)
GAS VALVE
NOTE: DO NOT USE YELLOW WIRE ON MICROSWITCH IN NORMAL
INSTALLATION. THE YELLOW WIRE IS TO BE USED ONLY FOR
EXTINGUISHER ALARM, LIGHTS, CIRCUITS, ETC.

MICROSWITCH

BASIC WIRING DIAGRAM
MANUAL RESET RELAY
RED (COMMON)

120V/60HZ

L1
L2
K1
Ka

YELLOW (N.O)

PUSHBUTTON SWITCH

K1b

BLACK (N.C.)

MICROSWITCH
CURRENT DRAW MAX:
8A RESISTIVE
8A INDUCTIVE
120VAC

NOTES:
1.
DENOTES FIELD INSTALLATION
2.
DENOTES FACTORY INSTALLATION
3. GAS VALVE: UL LISTED ELECTRICALLY-OPERATED SAFETY VALVE FOR NATURAL OR LP GAS AS NEEDED OF
APPROPRIATE PRESSURE AND TEMPERATURE RATING, 110V/60HZ OR AMEREX GAS VALVES, PN 12870, 12871,
12872, 12873, 12874, 12875 and 12876.
4. K1a and K1b ARE N.0. WHEN K1 IS DE-ENERGIZED.

22 Model GGH2O

GAS VALVE
SEE NOTE 3

TYPICAL WIRING SCHEMATIC ELECTRIC EQUIPMENT SHUTDOWN
ANSUL file name: Typicalwiringschematicelectricgasshut-offvalveshutdowndetail.ai / File received on August 4, 2010

TYPICAL
WIRING SWITCH
SCHEMATIC
ELECTRIC EQUIPMENT SHUTDOWN
Ansul®
Wiring
Plan View
BLACK
ANSUL SNAP-ACTION
(SWITCH CONTACTS SHOWN WITH ANSUL
AUTOMAN IN THE COCKED POSITION)

RED
BROWN
BLACK

ANSUL SNAP-ACTION SWITCH
(SWITCH CONTACTS SHOWN WITH ANSUL
AUTOMAN IN THE COCKED POSITION)

RESET POWER
INDICATOR

RED

RELAY COILRESET POWER
INDICATOR
A
RELAY

6
9
3B

RED

SCREW

BROWN

SCREW

4
7
COIL
1

L 2 NEUTRAL
110V/60HZ

GND

L 1 HOT

3
5
2

L 2 NEUTRAL
110V/60HZ

4
1

MANUAL 6RESET RELAY
PART NO.9426151

4
ELECTRICAL
RATING
1/3 HP,7110 AMP, 120 VAC
1/2 HP, 10 AMP, 240 VAC
13 AMP,
28 VDC
MANUAL
RESET
RELAY
PART NO. 426151

NOTE:

RED

GND

L 1 HOT

ELECTRICAL RATING

1/3 HP, 10 AMP, 120 VAC
DENOTES FIELD INSTALLATION

DENOTES FACTORY INSTALLATION
13 AMP, 28 VDC

1/2 HP, 10 AMP, 240 VAC

3. GAS VALVES: "UL LISTED ELECTRICALLY-OPERATED SAFETY VALVE FOR NATURAL, OR LP GAS AS NEEDED OF APPROPRIATE PRESSURE AND
TEMPERATURE RATING, 110V/60HZ OR ANSUL GAS VALVES, PART NUMBERS 13707, 13708, 13709, 13710. AND 17643.
NOTE:
4. DO NOT USE BLACK WIRE ON SNAP-ACTION SWITCH IN NORMAL INSTALLATION. (USED ONLY FOR EXTRANEOUS ALARM, LIGHT CIRCUITS, ETC.
DENOTES FIELD INSTALLATION
1.
2.

DENOTES FACTORY INSTALLATION

3. GAS VALVES: "UL LISTED ELECTRICALLY-OPERATED SAFETY VALVE FOR NATURAL, OR LP GAS AS NEEDED OF APPROPRIATE PRESSURE AND
TEMPERATURE RATING, 110V/60HZ OR ANSUL GAS VALVES, PART NUMBERS 13707, 13708, 13709, 13710. AND 17643.
BLACK
WIRE ON SNAP-ACTION SWITCH IN NORMAL INSTALLATION. (USED
ONLY
FOR EXTRANEOUS
ALARM,
4. DO NOT
ANSUL
fileUSE
name:
Typicalwiringschematicelectricequipmentshutdowndetail.ai
/ File
received
on August 4,
2010 LIGHT CIRCUITS, ETC.

TYPICAL WIRING SCHEMATIC ELECTRICAL EQUIPMENT SHUTDOWN

ANSUL file name: Typicalwiringschematicelectricequipmentshutdowndetail.ai /BLACK
File received on August 4, 2010

ANSUL SNAP-ACTION
TYPICAL
WIRING SWITCH
SCHEMATIC ELECTRICAL EQUIPMENT SHUTDOWN
(SWITCH CONTACTS SHOWN WITH ANSUL
AUTOMAN IN THE COCKED POSITION)

BROWN
BLACK

ANSUL SNAP-ACTION SWITCH
(SWITCH CONTACTS SHOWN WITH ANSUL
AUTOMAN IN THE COCKED POSITION)
A

RED

RESET POWER
INDICATOR
B

RED

RELAY COILRESET POWER
INDICATOR
A
RELAY

6
9
3B

RED

4
7
COIL
1

MANUAL 6RESET RELAY
PART NO.9426151
3

4
ELECTRICAL
RATING
1/3 HP,7110 AMP, 120 VAC
1/2 HP, 10 AMP, 240 VAC
13 AMP,
28 VDC
MANUAL
RESET
RELAY
PART NO. 426151

ELECTRICAL RATING
1/3 HP, 10 AMP, 120 VAC
1/2 HP, 10 AMP, 240 VAC
13 AMP, 28 VDC

RED

GND
SCREW

BROWN

GND
SCREW

L 2 NEUTRAL
110V/60HZ

L 1 HOT

3
5
2

L 2 NEUTRAL
110V/60HZ

4
1

L 1 HOT

SWITCH OR

2THERMOSTAT
(CUSTOMER
SUPPLIED)

SWITCH OR
THERMOSTAT
(CUSTOMER
SUPPLIED)

CONTACTOR
(CUSTOMER SUPPLIED)

CONTACTOR
(CUSTOMER SUPPLIED)
TO POWER SUPPLY
220V/440V

TO HEATING
ELEMENT LOAD

NOTE:
1.

DENOTES FIELD INSTALLATION

DENOTES FACTORY INSTALLATION

TO POWER SUPPLY
220V/440V

3. GAS VALVES: "UL LISTED ELECTRICALLY-OPERATED SAFETY VALVE FOR NATURAL, OR LP GAS AS NEEDED OF APPROPRIATE PRESSURE
TO HEATING
AND TEMPERATURE RATING, 110V/60HZ OR ANSUL GAS VALVES, PART NUMBERS
13707,LOAD
13708, 13709, 13710. AND 17643.
ELEMENT
NOTE:
4. DO NOT USE BLACK WIRE ON SNAP-ACTION SWITCH IN NORMAL INSTALLATION. (USED ONLY FOR EXTRANEOUS ALARM, LIGHT CIRCUITS, ETC.
DENOTES FIELD INSTALLATION
1.
2.
®

DENOTES FACTORY INSTALLATION

Model GGH2O
3. GAS VALVES: "UL LISTED ELECTRICALLY-OPERATED SAFETY VALVE FOR NATURAL, OR LP GAS AS NEEDED OF APPROPRIATE PRESSURE
AND TEMPERATURE RATING, 110V/60HZ OR ANSUL GAS VALVES, PART NUMBERS 13707, 13708, 13709, 13710. AND 17643.
4. DO NOT USE BLACK WIRE ON SNAP-ACTION SWITCH IN NORMAL INSTALLATION. (USED ONLY FOR EXTRANEOUS ALARM, LIGHT CIRCUITS, ETC.

LADDER DIAGRAM,
Wiring Diagram
GGH2O

CAD DRAWING NO.

REV.

PART NO.

ECO

P.O.BOX 410 SCHOFIELD, WISCONSIN 54476-0410

IAN31295

473596
Wiring diagram is located on the inside cover of the control
cabinet located on the end of the hood.
3POLE 32 AMPS
DISC

120VAC 1PH. 30 AMPS
SUPPLY POWER
WATER WASH
120VAC 1PH. 15AMPS
SUPPLY POWER
HOOD LIGHTS
FAN INTERLOCK
CONTACT

(H)

Hood Lights

BK H1
14 GA

N1 WHT

H1
RD

L2
E1

E1
18 GA

12 GA

WHT

R5 120 VAC

Fan
Interlock

Hood Lights

A1
A2
Hood Lights
LED Relay

14 GA

12 GA

FU2

(H)

18 GA

5 AMP

TR1

(N)

120VAC

24VAC

18 GA
BL

18 GA

U1 (FX-14)
83

83 - 24V (H)

N
S2 120 VAC
N
Nozzle 1
S3 120 VAC

RD S3
48

48 - DO3

WHT

Fill

RD
S2
45

45 - DO2

47 - DO3 COM

82
S1 120 VAC

RD
S1
42

42 - DO1

44 - DO2
COM

82 - 24V (C)

41 - DO1 COM

N
Nozzle 2

Melink Fan
Stop Common

PR
51

Tank Full

FL3

Tank Low
RD

Safety
BK

R1
11

68 - DO9

28 - DI6

COM

BR
73

OR
2

21
PB3

Clean Hood

24 - DI3

Start-Stop Fan
PR
11
24

PB2
R6

14
11
Wash Timer
R4

24
21
Fire Mode
R3
24
21

32 - DI9

Det Low
7 - AI3

OR
7

6 - AI COM

BR
6

5 - AI2
6 - AI COM

Temp Sensor
(IMC Interlock)
(If used)

81 - Earth
1

Clean Hood
Indicator

PR
PR

26 - DI4

A1
L3

23 - DI2

4 - AI COM

BR
6

73 - AO COM
2 - AI1

BR
4
OR
5

72 - AO1

22 - DI1

36 - DI12

RD
68

Overload

R2 24 VAC
Detergent Pump

C1
96 WHT

A1
A2
R1 24 VAC
Fan

21 - DI
COM

27 - DI5

1 - AI COM

3 - Ext V
25 - DI
COM

+VDC

67 - DO9 COM

C1 120 VAC
Recirc Pump

WHT

62 - DO7

65 - DO8

S4 120 VAC
Drain

58 - DO6

64 - DO8 COM

27
PR

OR
72

Temp Sensor
(Freeze
Protection)
(If used)
Temp Sensor
(IMC Interlock)
(If used)

RD
S4
55

WHT

GGH20/VAV Fan Mode
Interlock Connection
0VDC - Fan Auto
5VDC - Fan OFF
10VDC - Fan On for Dry

55 - DO5

61 - DO7
COM

FL2

54 - DO5 COM

FL1

PR
M1 Melink Fan Stop
52

57 - DO6 COM

WHT

52 - DO4

51 - DO4 COM

6
Fan Indicator

L1
20

2
Lights Indicator

L4
OR

3
Low Det Indicator

FL4

R3 24 VAC

A1
A2
Det Low
BL

A2
A1
Fire Mode
BL

Fire System

R4 24 VAC

Det Low

AR 24 VAC

2
PB1

3
6

Lights On/Off

BK 12 GA

FU3

Timer
Contact

BK 18 GA

R6 120 VAC

A2
A1
Wash Timer
Relay
14

LF3

3 AMP

FU1

25 AMP
LF1

12 GA

24 Model GGH2O

C1 120VAC
T2 T2
L2

Recirculating
Pump
Contactor

FLA
17
22

WHT

Detergent
Pump
Motor

BK
WHT

WHT

Recirculating
Pump
Motor

MOLEX PLUG FOR KEYPAD
(IF KEYPAD IS REMOTE MOUNTED, PLUG IS FIELD CONNECTED)

Blue

Yellow

FIELD INSTALLED WIRING

White

Orange

P2
BK
DP

T3
RP

Brown

Recirculating Pump
Motor Wiring
Recirculating Pump Size
1.0 HP
1.5 HP

WIRED FROM MOTOR
ON RECIRCULATING
PUMP

BK 12 GA

WHT

RP
N

Maintenance
Capture Tank

Floats

The interior surfaces of the hood capture tank should
be wiped down weekly.

The floats need to be
inspected two weeks after
start-up and then once a
month thereafter.

Filters
The Grease Grabber filters (bead filters) require
visually inspection (not removed from hood) two
weeks after start-up, then once a month thereafter to
make certain the filters are positioned correctly in the
plenum. Positioned correctly means there are no gaps
between the filters.
To inspect the bead filters, remove the fasteners
holding the access doors; each door has five (5)
fasteners. Remove every other door to inspect the
filters.

The float can be inspected
by first turning the
disconnect switch on the
control cabinet to the ‘OFF’
position. Then remove the
large access panel door.
Once the access panel
is removed, you will have
access to the floats.

After inspecting the filters, put the access doors
back on and put the fasteners back in. Be careful not
to over-tighten or cross thread the fasteners when
putting them back in.
The Grease Grabber filters
(bead filters) need to be
removed from the hood
once every three months to
visually inspect and ensure
the filters are structurally
sound.
Remove all the doors
and remove the filters for
inspection. Depending on
the equipment under the
hood, it will probably be
easier to remove the filters
from the right side of each
hood. Slide the other filters
down to the end access
door for removal.
After inspecting the filters,
place them back in the
hood. Be careful to install
the filters with the handles
up and make sure not to
hit the fire detection line
when removing or installing
the filters. Ensure no gaps
are between filters after
installation.

Access Panel Door

Float Installed

Slide each float (Low Float,
High Float and Safety Float)
up the stem to its stop with
your finger and let go. If float
slides freely down the stem
with minimal resistance, the
float is operating as it should.
Put the access panel back
on and turn the disconnect
switch to the ‘ON’ position.

Safety Float

High Float

Low Float

If the float does not slide
freely down the stem, the
stem and floats are dirty
and need to be wiped off with a clean cloth. Cleaning
the stem involves removing all the clips (stops). Slide
floats up and down on the shaft as required to access
and clean the entire length of the shaft. Return floats
to their location and reinstall stops.
Make sure all float stops are securely located in their
grooves and floats are located in their designated
spots.
If for some reason the floats
get taken off the stem, the
stamped circle on the top
side of the float needs to
face up.

If any filter appears damaged, consult factory for
replacement.
NOTE
Be careful when handling the float stops. These are
small clips and can easily be dropped. If you loose
one of these clips, consult factory for a replacement.

Model GGH2O 25

Troubleshooting

Replacement Parts

Hood is not cleaning

When ordering parts, please be prepared to provide
us with your cabinet and hood system model
number, and serial number from labels on the hood
and cabinet. See the chart below to identify the
replacement parts needed.

If the hood does not seem to be adequately cleaned,
look for the following:
Detergent tank — is it empty or filled with wrong
detergent?
Detergent pump — is the detergent pump running?
Is there power to the pump? Is the detergent level
low? If the hood plenum area is not sufficiently
cleaning, consult factory for information on
increasing duration of wash cycle and detergent
pump.
Nozzles — are any of them clogged? If so, they can
be removed and cleared using a small wire.
Water temperature — is it at least 140°F.
Hardness of water — test water for hardness level.
It is recommended that soft water be used.

Greenheck
Part
Number
Wash Nozzles
Above GG Filters
Below GG Filters
Before First Stage Filters
Repair Kits
Solenoid Model 1A579
Solenoid Model 1A578

Grainger®
Part
Number

472806
472795
472805
K-1180
K-1172

Hood not draining properly — plugged drain.
Ensure all floats have stamped circles facing up.

Water leaks — water leaking through the access
panels when filling. Ensure access panels are securely
in place. If leak persists, partially close inlet water ball
valve (by others) upstream of fill solenoid to reduce
water pressure.
Condensation in the hood — large amounts of
condensation while hood is washing. Hood should
be washed after the hood and equipment is warm,
not hot. The warm equipment helps reduce the
condensation that forms in the hood.
Approved wash detergent

Formula G-510 from 2010 Products, Inc.
Phone: 800-286-2010
(Not provided by Greenheck).

26 Model GGH2O

Grease Grabber™ H2O Start-Up
Checklist
Check boxes when item has been verified and gone
over with customer.

o Wash Mode
• See sequence of operations on page 20.

Hook-Up

• If using 24 hour / 7 day timer, wash cycle will start
at scheduled time after “Fan On/Off” push button
has been pressed. (Refer to page 18 for details on
programming 24 hour / 7 day timer). If 24 hour / 7
day timer is not being used, press “Clean Hood”
push button after pressing “Fan On/Off” push
button.

o Electrical Connected
• 120V/1 30A to terminals L1 and N for wash
controls
• 120V/1 15A to terminals L2 and N1 for hood lights
• Fans to terminals E1 and E2 (dry contact)
If using variable volume controls, Melink will also
require connection to terminals M1 and M2, VariFlow will only require connection to terminals V1
and VC.
• Fire system microswitch to terminals FS and FC.
• Recirculating pump wired to cabinet terminals
RP and N.
• If keypad is shipped loose, connection completed
between keypad and cabinet with supplied cable.
If additional cable is required, consult factory for
ordering.
o Plumbing Connected
• Two 1-inch unions to recirculating pump
connected.
• Hot water supply line, 3/4-inch connection.
• Pressurized drain connection, 1-inch connection.
• Hot water supply ball valve open. Located up
stream of the inlet water solenoid valve.
o Detergent
• Suction tubing and strainer to bottom of detergent
tank.
• Low detergent sensor in bottom of detergent tank.
• Detergent tank filled with proper detergent.
o Timer, 24 hours / 7 day
• Programmed - see instructions on page 18.

Start-Up
o Cooking Mode
• See sequence of operations on page 20.
• Hood lights on. Activate “Hood Lights” push
button.
• Hood light LED indicator should be lit.
• Fans on. Hold “Fan On/Off” push button for onehalf second.
• Fan LED indicator should be lit.

• Clean hood LED indicator should be lit.
_________ Record water pressure
(Should be between 30-50 psi)
_________ Record water temperature
(Should be between 140-160°F.)
o Stop Mode
• At end of wash cycle, system returns to Fan On
for 20 minutes dry cycle.
• System resets to stop mode.
• Hood lights off. Deactivate “Hood Lights” push
button.
• All lights on face of keypad(s) should be off.
o Fire Mode
• Trip fire system microswitch or remove wire
from terminal FS or FC. (Water will not spray in
fire mode, fans will run. If wash cycle is running
during fire system trip, hood will drain and fan(s)
will run).
• System fault LED indicator should be on.
• Fan LED indicator should be lit.
o Low Detergent Mode
• Fill detergent tank with appropriate detergent.
• Low detergent LED indicator should go off.

Miscellaneous
o Hood Access
• Panels should fit tightly to prevent water spraying
out.
• When front nozzles are washing, adjust ball valve
in cabinet to reduce water pressure and minimize
overspray.
o Cleaning
• Is the hood cleaning properly?
• If not, refer to troubleshooting guide on page 26.

• Appliances on (gas and/or electric).
o Stop Mode
• See sequence of operations on page 20.
• Fans off. Hold “Fan On/Off” push button for onehalf second.
• LED indicator turns off.
®

Model GGH2O 27

Maintenance Log
Date___________________ Time______________ AM/PM
Notes:___________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________

Date___________________ Time______________ AM/PM
Notes:___________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________

Warranty
Greenheck warrants this equipment to be free from defects in material and workmanship for a period of one year from
the shipment date. Any units or parts which prove defective during the warranty period will be replaced at our option
when returned to our factory, transportation prepaid. Motors are warranted by the motor manufacturer for a period of
one year. Should motors furnished by Greenheck prove defective during this period, they should be returned to the
nearest authorized motor service station. Greenheck will not be responsible for any removal or installation costs.
As a result of our commitment to continuous improvement, Greenheck reserves the right to change specifications
without notice.

Greenheck catalog GGH2O provides additional information
describing the equipment, fan performance, available
accessories, and specification data.

AMCA Publication 410-96, Safety Practices for Users and
Installers of Industrial and Commercial Fans, provides
additional safety information. This publication can be
obtained from AMCA International, Inc. at www.amca.org.

Phone: (715) 359-6171 • Fax: (715) 355-2399 • E-mail: gfcinfo@greenheck.com • Website: www.greenheck.com

28 473380 • Grease Grabber™ H2O Auto Cleaning Hood, Rev. 1, August 2010

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.2.2-c063 53.352624, 2008/07/30-18:12:18
Instance ID                     : uuid:9719df52-857f-425c-ac3a-177327ca5a19
Document ID                     : xmp.did:BCEF497E2FB4DF118E42A5494D4648E1
Original Document ID            : adobe:docid:indd:10500fb6-648b-11dd-bfff-f10d95deb459
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:BBEF497E2FB4DF118E42A5494D4648E1
Derived From Document ID        : xmp.did:FEBAC32E14B2DF11A95ED6A123401F25
Derived From Original Document ID: adobe:docid:indd:10500fb6-648b-11dd-bfff-f10d95deb459
Derived From Rendition Class    : default
History Action                  : saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved
History Instance ID             : xmp.iid:8F551BD13F0FDF11BB25B0196F2ADBD6, xmp.iid:90551BD13F0FDF11BB25B0196F2ADBD6, xmp.iid:91551BD13F0FDF11BB25B0196F2ADBD6, xmp.iid:92551BD13F0FDF11BB25B0196F2ADBD6, xmp.iid:93551BD13F0FDF11BB25B0196F2ADBD6, xmp.iid:94551BD13F0FDF11BB25B0196F2ADBD6, xmp.iid:BA380EB4690FDF11A61ECBC5661477A5, xmp.iid:BB380EB4690FDF11A61ECBC5661477A5, xmp.iid:BD380EB4690FDF11A61ECBC5661477A5, xmp.iid:BE380EB4690FDF11A61ECBC5661477A5, xmp.iid:BF380EB4690FDF11A61ECBC5661477A5, xmp.iid:C0380EB4690FDF11A61ECBC5661477A5, xmp.iid:F98B1D052010DF11AF4FFEB90DE976C5, xmp.iid:FA8B1D052010DF11AF4FFEB90DE976C5, xmp.iid:FB8B1D052010DF11AF4FFEB90DE976C5, xmp.iid:FC8B1D052010DF11AF4FFEB90DE976C5, xmp.iid:FD8B1D052010DF11AF4FFEB90DE976C5, xmp.iid:FE8B1D052010DF11AF4FFEB90DE976C5, xmp.iid:FF8B1D052010DF11AF4FFEB90DE976C5, xmp.iid:008C1D052010DF11AF4FFEB90DE976C5, xmp.iid:018C1D052010DF11AF4FFEB90DE976C5, xmp.iid:028C1D052010DF11AF4FFEB90DE976C5, xmp.iid:06C3C5C74210DF11AF4FFEB90DE976C5, xmp.iid:07C3C5C74210DF11AF4FFEB90DE976C5, xmp.iid:08C3C5C74210DF11AF4FFEB90DE976C5, xmp.iid:09C3C5C74210DF11AF4FFEB90DE976C5, xmp.iid:405B55901326DF11A78598FDA7642E44, xmp.iid:415B55901326DF11A78598FDA7642E44, xmp.iid:425B55901326DF11A78598FDA7642E44, xmp.iid:435B55901326DF11A78598FDA7642E44, xmp.iid:445B55901326DF11A78598FDA7642E44, xmp.iid:455B55901326DF11A78598FDA7642E44, xmp.iid:465B55901326DF11A78598FDA7642E44, xmp.iid:475B55901326DF11A78598FDA7642E44, xmp.iid:144799DAE326DF11A3DE9F3B9D8F98C3, xmp.iid:154799DAE326DF11A3DE9F3B9D8F98C3, xmp.iid:164799DAE326DF11A3DE9F3B9D8F98C3, xmp.iid:174799DAE326DF11A3DE9F3B9D8F98C3, xmp.iid:184799DAE326DF11A3DE9F3B9D8F98C3, xmp.iid:194799DAE326DF11A3DE9F3B9D8F98C3, xmp.iid:1A4799DAE326DF11A3DE9F3B9D8F98C3, xmp.iid:1B4799DAE326DF11A3DE9F3B9D8F98C3, xmp.iid:1C4799DAE326DF11A3DE9F3B9D8F98C3, xmp.iid:1D4799DAE326DF11A3DE9F3B9D8F98C3, xmp.iid:B89A91250E27DF11A3DE9F3B9D8F98C3, xmp.iid:2C91649E5C28DF1185B2D9F9D34214E9, xmp.iid:2D91649E5C28DF1185B2D9F9D34214E9, xmp.iid:2E91649E5C28DF1185B2D9F9D34214E9, xmp.iid:2F91649E5C28DF1185B2D9F9D34214E9, xmp.iid:3091649E5C28DF1185B2D9F9D34214E9, xmp.iid:3191649E5C28DF1185B2D9F9D34214E9, xmp.iid:38224EE17A2CDF119C74E1248D0AC699, xmp.iid:39224EE17A2CDF119C74E1248D0AC699, xmp.iid:3C224EE17A2CDF119C74E1248D0AC699, xmp.iid:3D224EE17A2CDF119C74E1248D0AC699, xmp.iid:C79E17788D2CDF119C74E1248D0AC699, xmp.iid:C89E17788D2CDF119C74E1248D0AC699, xmp.iid:C99E17788D2CDF119C74E1248D0AC699, xmp.iid:CA9E17788D2CDF119C74E1248D0AC699, xmp.iid:675447450F2DDF11B5628BA083E1D316, xmp.iid:685447450F2DDF11B5628BA083E1D316, xmp.iid:695447450F2DDF11B5628BA083E1D316, xmp.iid:6A5447450F2DDF11B5628BA083E1D316, xmp.iid:A5E8ADF6F235DF119032873838A65159, xmp.iid:A6E8ADF6F235DF119032873838A65159, xmp.iid:A1A3EDC5BD36DF11A9BFD4E33DE4BF02, xmp.iid:A2A3EDC5BD36DF11A9BFD4E33DE4BF02, xmp.iid:A3A3EDC5BD36DF11A9BFD4E33DE4BF02, xmp.iid:80C568960C48DF11BBFFF2C48E6A9B81, xmp.iid:37ADFB2E7F4DDF11AC6BEA02527FAEEB, xmp.iid:38ADFB2E7F4DDF11AC6BEA02527FAEEB, xmp.iid:43F8351E2B4EDF11A680A4EA8239F59A, xmp.iid:44F8351E2B4EDF11A680A4EA8239F59A, xmp.iid:45F8351E2B4EDF11A680A4EA8239F59A, xmp.iid:46F8351E2B4EDF11A680A4EA8239F59A, xmp.iid:0AE1F914424EDF11BCF0CD811FD411DB, xmp.iid:9372B0752459DF11A7C6A6CBC84ABE52, xmp.iid:9472B0752459DF11A7C6A6CBC84ABE52, xmp.iid:9572B0752459DF11A7C6A6CBC84ABE52, xmp.iid:9672B0752459DF11A7C6A6CBC84ABE52, xmp.iid:9772B0752459DF11A7C6A6CBC84ABE52, xmp.iid:9872B0752459DF11A7C6A6CBC84ABE52, xmp.iid:9B72B0752459DF11A7C6A6CBC84ABE52, xmp.iid:9C72B0752459DF11A7C6A6CBC84ABE52, xmp.iid:F73F1B2CED59DF119D0B964DF6EC61CD, xmp.iid:F83F1B2CED59DF119D0B964DF6EC61CD, xmp.iid:F93F1B2CED59DF119D0B964DF6EC61CD, xmp.iid:FA3F1B2CED59DF119D0B964DF6EC61CD, xmp.iid:FB3F1B2CED59DF119D0B964DF6EC61CD, xmp.iid:FC3F1B2CED59DF119D0B964DF6EC61CD, xmp.iid:3368547B6767DF11A09C92250794E234, xmp.iid:3468547B6767DF11A09C92250794E234, xmp.iid:3568547B6767DF11A09C92250794E234, xmp.iid:3668547B6767DF11A09C92250794E234, xmp.iid:3768547B6767DF11A09C92250794E234, xmp.iid:3868547B6767DF11A09C92250794E234, xmp.iid:78BA8569DA68DF11986897D1F94B200E, xmp.iid:79BA8569DA68DF11986897D1F94B200E, xmp.iid:7ABA8569DA68DF11986897D1F94B200E, xmp.iid:7BBA8569DA68DF11986897D1F94B200E, xmp.iid:F0F86A6E906ADF119FEAB4386706A818, xmp.iid:F1F86A6E906ADF119FEAB4386706A818, xmp.iid:F2F86A6E906ADF119FEAB4386706A818, xmp.iid:F3F86A6E906ADF119FEAB4386706A818, xmp.iid:BB33AC098F6DDF11B85EF62A19A9CFAB, xmp.iid:BC33AC098F6DDF11B85EF62A19A9CFAB, xmp.iid:BD33AC098F6DDF11B85EF62A19A9CFAB, xmp.iid:BE33AC098F6DDF11B85EF62A19A9CFAB, xmp.iid:7FCA36F6BA6DDF11B85EF62A19A9CFAB, xmp.iid:80CA36F6BA6DDF11B85EF62A19A9CFAB, xmp.iid:35FCC181846EDF11AA8E9AF3D7AAAA86, xmp.iid:36FCC181846EDF11AA8E9AF3D7AAAA86, xmp.iid:37FCC181846EDF11AA8E9AF3D7AAAA86, xmp.iid:38FCC181846EDF11AA8E9AF3D7AAAA86, xmp.iid:39FCC181846EDF11AA8E9AF3D7AAAA86, xmp.iid:F6FFFCE2397DDF1187AAF9EB14D5022B, xmp.iid:F7FFFCE2397DDF1187AAF9EB14D5022B, xmp.iid:F8FFFCE2397DDF1187AAF9EB14D5022B, xmp.iid:F9FFFCE2397DDF1187AAF9EB14D5022B, xmp.iid:FAFFFCE2397DDF1187AAF9EB14D5022B, xmp.iid:FBFFFCE2397DDF1187AAF9EB14D5022B, xmp.iid:FCFFFCE2397DDF1187AAF9EB14D5022B, xmp.iid:C25BFFDA4E7DDF1187AAF9EB14D5022B, xmp.iid:863FD4C29A84DF11B7FF96A25B6011E2, xmp.iid:873FD4C29A84DF11B7FF96A25B6011E2, xmp.iid:8AABD5945885DF118DF6BE3DEC66F0A8, xmp.iid:8BABD5945885DF118DF6BE3DEC66F0A8, xmp.iid:8CABD5945885DF118DF6BE3DEC66F0A8, xmp.iid:8DABD5945885DF118DF6BE3DEC66F0A8, xmp.iid:ABBEB0E4608FDF11AE0AE6FF79FC03BC, xmp.iid:ACBEB0E4608FDF11AE0AE6FF79FC03BC, xmp.iid:ADBEB0E4608FDF11AE0AE6FF79FC03BC, xmp.iid:AEBEB0E4608FDF11AE0AE6FF79FC03BC, xmp.iid:AFBEB0E4608FDF11AE0AE6FF79FC03BC, xmp.iid:B0BEB0E4608FDF11AE0AE6FF79FC03BC, xmp.iid:D4525E9B5390DF11ADF0E4AB5291C2AE, xmp.iid:D5525E9B5390DF11ADF0E4AB5291C2AE, xmp.iid:25F62ECDEE90DF11A9F7E8C77C614645, xmp.iid:26F62ECDEE90DF11A9F7E8C77C614645, xmp.iid:27F62ECDEE90DF11A9F7E8C77C614645, xmp.iid:28F62ECDEE90DF11A9F7E8C77C614645, xmp.iid:29F62ECDEE90DF11A9F7E8C77C614645, xmp.iid:2AF62ECDEE90DF11A9F7E8C77C614645, xmp.iid:B9436E964194DF119A978189BA7D3A9A, xmp.iid:BA436E964194DF119A978189BA7D3A9A, xmp.iid:BB436E964194DF119A978189BA7D3A9A, xmp.iid:BC436E964194DF119A978189BA7D3A9A, xmp.iid:E500F34F249BDF119355EC626F33D235, xmp.iid:E600F34F249BDF119355EC626F33D235, xmp.iid:E700F34F249BDF119355EC626F33D235, xmp.iid:E800F34F249BDF119355EC626F33D235, xmp.iid:59439BF8F89BDF11B064E3C68DAFA757, xmp.iid:5A439BF8F89BDF11B064E3C68DAFA757, xmp.iid:5D439BF8F89BDF11B064E3C68DAFA757, xmp.iid:5E439BF8F89BDF11B064E3C68DAFA757, xmp.iid:5F439BF8F89BDF11B064E3C68DAFA757, xmp.iid:62439BF8F89BDF11B064E3C68DAFA757, xmp.iid:2CDECC550F9CDF11B064E3C68DAFA757, xmp.iid:2DDECC550F9CDF11B064E3C68DAFA757, xmp.iid:2EDECC550F9CDF11B064E3C68DAFA757, xmp.iid:2FDECC550F9CDF11B064E3C68DAFA757, xmp.iid:30DECC550F9CDF11B064E3C68DAFA757, xmp.iid:31DECC550F9CDF11B064E3C68DAFA757, xmp.iid:32DECC550F9CDF11B064E3C68DAFA757, xmp.iid:33DECC550F9CDF11B064E3C68DAFA757, xmp.iid:34DECC550F9CDF11B064E3C68DAFA757, xmp.iid:35DECC550F9CDF11B064E3C68DAFA757, xmp.iid:36DECC550F9CDF11B064E3C68DAFA757, xmp.iid:B4A31372489EDF119DC5DDAD3C2A70E1, xmp.iid:B5A31372489EDF119DC5DDAD3C2A70E1, xmp.iid:B6A31372489EDF119DC5DDAD3C2A70E1, xmp.iid:B7A31372489EDF119DC5DDAD3C2A70E1, xmp.iid:B8A31372489EDF119DC5DDAD3C2A70E1, xmp.iid:B9A31372489EDF119DC5DDAD3C2A70E1, xmp.iid:BAA31372489EDF119DC5DDAD3C2A70E1, xmp.iid:BBA31372489EDF119DC5DDAD3C2A70E1, xmp.iid:BCA31372489EDF119DC5DDAD3C2A70E1, xmp.iid:CFECC5E96C9EDF119DC5DDAD3C2A70E1, xmp.iid:D0ECC5E96C9EDF119DC5DDAD3C2A70E1, xmp.iid:D1ECC5E96C9EDF119DC5DDAD3C2A70E1, xmp.iid:D2ECC5E96C9EDF119DC5DDAD3C2A70E1, xmp.iid:D3ECC5E96C9EDF119DC5DDAD3C2A70E1, xmp.iid:D4ECC5E96C9EDF119DC5DDAD3C2A70E1, xmp.iid:D5ECC5E96C9EDF119DC5DDAD3C2A70E1, xmp.iid:D6ECC5E96C9EDF119DC5DDAD3C2A70E1, xmp.iid:D7ECC5E96C9EDF119DC5DDAD3C2A70E1, xmp.iid:D8ECC5E96C9EDF119DC5DDAD3C2A70E1, xmp.iid:D9ECC5E96C9EDF119DC5DDAD3C2A70E1, xmp.iid:D46E6589709EDF119DC5DDAD3C2A70E1, xmp.iid:D56E6589709EDF119DC5DDAD3C2A70E1, xmp.iid:D66E6589709EDF119DC5DDAD3C2A70E1, xmp.iid:D76E6589709EDF119DC5DDAD3C2A70E1, xmp.iid:D86E6589709EDF119DC5DDAD3C2A70E1, xmp.iid:D96E6589709EDF119DC5DDAD3C2A70E1, xmp.iid:DA6E6589709EDF119DC5DDAD3C2A70E1, xmp.iid:DB6E6589709EDF119DC5DDAD3C2A70E1, xmp.iid:DC6E6589709EDF119DC5DDAD3C2A70E1, xmp.iid:DD6E6589709EDF119DC5DDAD3C2A70E1, xmp.iid:DE6E6589709EDF119DC5DDAD3C2A70E1, xmp.iid:0D95CDFA759EDF119DC5DDAD3C2A70E1, xmp.iid:0E95CDFA759EDF119DC5DDAD3C2A70E1, xmp.iid:0F95CDFA759EDF119DC5DDAD3C2A70E1, xmp.iid:1095CDFA759EDF119DC5DDAD3C2A70E1, xmp.iid:1195CDFA759EDF119DC5DDAD3C2A70E1, xmp.iid:1295CDFA759EDF119DC5DDAD3C2A70E1, xmp.iid:1395CDFA759EDF119DC5DDAD3C2A70E1, xmp.iid:1495CDFA759EDF119DC5DDAD3C2A70E1, xmp.iid:1595CDFA759EDF119DC5DDAD3C2A70E1, xmp.iid:C6957405059FDF11A01FF71446D585AB, xmp.iid:C7957405059FDF11A01FF71446D585AB, xmp.iid:C8957405059FDF11A01FF71446D585AB, xmp.iid:C9957405059FDF11A01FF71446D585AB, xmp.iid:CA957405059FDF11A01FF71446D585AB, xmp.iid:CB957405059FDF11A01FF71446D585AB, xmp.iid:CC957405059FDF11A01FF71446D585AB, xmp.iid:CD957405059FDF11A01FF71446D585AB, xmp.iid:CE957405059FDF11A01FF71446D585AB, xmp.iid:CF957405059FDF11A01FF71446D585AB, xmp.iid:F557BA1B119FDF11A01FF71446D585AB, xmp.iid:F657BA1B119FDF11A01FF71446D585AB, xmp.iid:F757BA1B119FDF11A01FF71446D585AB, xmp.iid:F857BA1B119FDF11A01FF71446D585AB, xmp.iid:F957BA1B119FDF11A01FF71446D585AB, xmp.iid:FA57BA1B119FDF11A01FF71446D585AB, xmp.iid:FB57BA1B119FDF11A01FF71446D585AB, xmp.iid:FC57BA1B119FDF11A01FF71446D585AB, xmp.iid:FD57BA1B119FDF11A01FF71446D585AB, xmp.iid:FE57BA1B119FDF11A01FF71446D585AB, xmp.iid:FF57BA1B119FDF11A01FF71446D585AB, xmp.iid:CFFF9E85199FDF11A01FF71446D585AB, xmp.iid:D0FF9E85199FDF11A01FF71446D585AB, xmp.iid:D1FF9E85199FDF11A01FF71446D585AB, xmp.iid:D2FF9E85199FDF11A01FF71446D585AB, xmp.iid:D3FF9E85199FDF11A01FF71446D585AB, xmp.iid:D4FF9E85199FDF11A01FF71446D585AB, xmp.iid:D5FF9E85199FDF11A01FF71446D585AB, xmp.iid:D6FF9E85199FDF11A01FF71446D585AB, xmp.iid:D7FF9E85199FDF11A01FF71446D585AB, xmp.iid:D8FF9E85199FDF11A01FF71446D585AB, xmp.iid:D9FF9E85199FDF11A01FF71446D585AB, xmp.iid:A88B06F01E9FDF11A01FF71446D585AB, xmp.iid:A98B06F01E9FDF11A01FF71446D585AB, xmp.iid:AA8B06F01E9FDF11A01FF71446D585AB, xmp.iid:AB8B06F01E9FDF11A01FF71446D585AB, xmp.iid:AC8B06F01E9FDF11A01FF71446D585AB, xmp.iid:AD8B06F01E9FDF11A01FF71446D585AB, xmp.iid:AE8B06F01E9FDF11A01FF71446D585AB, xmp.iid:AF8B06F01E9FDF11A01FF71446D585AB, xmp.iid:B08B06F01E9FDF11A01FF71446D585AB, xmp.iid:B18B06F01E9FDF11A01FF71446D585AB, xmp.iid:B28B06F01E9FDF11A01FF71446D585AB, xmp.iid:C83361592F9FDF11A01FF71446D585AB, xmp.iid:C93361592F9FDF11A01FF71446D585AB, xmp.iid:CA3361592F9FDF11A01FF71446D585AB, xmp.iid:CB3361592F9FDF11A01FF71446D585AB, xmp.iid:CC3361592F9FDF11A01FF71446D585AB, xmp.iid:CD3361592F9FDF11A01FF71446D585AB, xmp.iid:CE3361592F9FDF11A01FF71446D585AB, xmp.iid:CF3361592F9FDF11A01FF71446D585AB, xmp.iid:D03361592F9FDF11A01FF71446D585AB, xmp.iid:D13361592F9FDF11A01FF71446D585AB, xmp.iid:AC2252EA3E9FDF119CA9B324AA2E7BE9, xmp.iid:AD2252EA3E9FDF119CA9B324AA2E7BE9, xmp.iid:AE2252EA3E9FDF119CA9B324AA2E7BE9, xmp.iid:AF2252EA3E9FDF119CA9B324AA2E7BE9, xmp.iid:B02252EA3E9FDF119CA9B324AA2E7BE9, xmp.iid:B12252EA3E9FDF119CA9B324AA2E7BE9, xmp.iid:EFC6E75CC99FDF118ED189DBDF68B4F5, xmp.iid:F0C6E75CC99FDF118ED189DBDF68B4F5, xmp.iid:F1C6E75CC99FDF118ED189DBDF68B4F5, xmp.iid:F2C6E75CC99FDF118ED189DBDF68B4F5, xmp.iid:F3C6E75CC99FDF118ED189DBDF68B4F5, xmp.iid:F4C6E75CC99FDF118ED189DBDF68B4F5, xmp.iid:F5C6E75CC99FDF118ED189DBDF68B4F5, xmp.iid:F6C6E75CC99FDF118ED189DBDF68B4F5, xmp.iid:F7C6E75CC99FDF118ED189DBDF68B4F5, xmp.iid:F8C6E75CC99FDF118ED189DBDF68B4F5, xmp.iid:02B837E6D69FDF118ED189DBDF68B4F5, xmp.iid:03B837E6D69FDF118ED189DBDF68B4F5, xmp.iid:04B837E6D69FDF118ED189DBDF68B4F5, xmp.iid:05B837E6D69FDF118ED189DBDF68B4F5, xmp.iid:06B837E6D69FDF118ED189DBDF68B4F5, xmp.iid:07B837E6D69FDF118ED189DBDF68B4F5, xmp.iid:08B837E6D69FDF118ED189DBDF68B4F5, xmp.iid:09B837E6D69FDF118ED189DBDF68B4F5, xmp.iid:0AB837E6D69FDF118ED189DBDF68B4F5, xmp.iid:0BB837E6D69FDF118ED189DBDF68B4F5, xmp.iid:0CB837E6D69FDF118ED189DBDF68B4F5, xmp.iid:FAA89595E09FDF118ED189DBDF68B4F5, xmp.iid:FBA89595E09FDF118ED189DBDF68B4F5, xmp.iid:FCA89595E09FDF118ED189DBDF68B4F5, xmp.iid:FDA89595E09FDF118ED189DBDF68B4F5, xmp.iid:FEA89595E09FDF118ED189DBDF68B4F5, xmp.iid:FFA89595E09FDF118ED189DBDF68B4F5, xmp.iid:00A99595E09FDF118ED189DBDF68B4F5, xmp.iid:01A99595E09FDF118ED189DBDF68B4F5, xmp.iid:02A99595E09FDF118ED189DBDF68B4F5, xmp.iid:03A99595E09FDF118ED189DBDF68B4F5, xmp.iid:04A99595E09FDF118ED189DBDF68B4F5, xmp.iid:CE0D1BA4E69FDF118ED189DBDF68B4F5, xmp.iid:CF0D1BA4E69FDF118ED189DBDF68B4F5, xmp.iid:D00D1BA4E69FDF118ED189DBDF68B4F5, xmp.iid:D10D1BA4E69FDF118ED189DBDF68B4F5, xmp.iid:D20D1BA4E69FDF118ED189DBDF68B4F5, xmp.iid:D30D1BA4E69FDF118ED189DBDF68B4F5, xmp.iid:D40D1BA4E69FDF118ED189DBDF68B4F5, xmp.iid:D50D1BA4E69FDF118ED189DBDF68B4F5, xmp.iid:D60D1BA4E69FDF118ED189DBDF68B4F5, xmp.iid:D70D1BA4E69FDF118ED189DBDF68B4F5, xmp.iid:D80D1BA4E69FDF118ED189DBDF68B4F5, xmp.iid:E38F66F2F89FDF118ED189DBDF68B4F5, xmp.iid:E48F66F2F89FDF118ED189DBDF68B4F5, xmp.iid:E58F66F2F89FDF118ED189DBDF68B4F5, xmp.iid:E68F66F2F89FDF118ED189DBDF68B4F5, xmp.iid:E78F66F2F89FDF118ED189DBDF68B4F5, xmp.iid:E88F66F2F89FDF118ED189DBDF68B4F5, xmp.iid:E98F66F2F89FDF118ED189DBDF68B4F5, xmp.iid:EA8F66F2F89FDF118ED189DBDF68B4F5, xmp.iid:EB8F66F2F89FDF118ED189DBDF68B4F5, xmp.iid:0BC678FE89A0DF11A0EBDF2010A5A5C5, xmp.iid:0CC678FE89A0DF11A0EBDF2010A5A5C5, xmp.iid:1AE1D5FC92A0DF11A0EBDF2010A5A5C5, xmp.iid:1BE1D5FC92A0DF11A0EBDF2010A5A5C5, xmp.iid:1CE1D5FC92A0DF11A0EBDF2010A5A5C5, xmp.iid:8ED102D698A0DF11A0EBDF2010A5A5C5, xmp.iid:8FD102D698A0DF11A0EBDF2010A5A5C5, xmp.iid:90D102D698A0DF11A0EBDF2010A5A5C5, xmp.iid:91D102D698A0DF11A0EBDF2010A5A5C5, xmp.iid:92D102D698A0DF11A0EBDF2010A5A5C5, xmp.iid:94D102D698A0DF11A0EBDF2010A5A5C5, xmp.iid:95D102D698A0DF11A0EBDF2010A5A5C5, xmp.iid:96D102D698A0DF11A0EBDF2010A5A5C5, xmp.iid:97D102D698A0DF11A0EBDF2010A5A5C5, xmp.iid:98D102D698A0DF11A0EBDF2010A5A5C5, xmp.iid:746572D2A3A0DF11A0EBDF2010A5A5C5, xmp.iid:756572D2A3A0DF11A0EBDF2010A5A5C5, xmp.iid:766572D2A3A0DF11A0EBDF2010A5A5C5, xmp.iid:776572D2A3A0DF11A0EBDF2010A5A5C5, xmp.iid:786572D2A3A0DF11A0EBDF2010A5A5C5, xmp.iid:796572D2A3A0DF11A0EBDF2010A5A5C5, xmp.iid:7A6572D2A3A0DF11A0EBDF2010A5A5C5, xmp.iid:7B6572D2A3A0DF11A0EBDF2010A5A5C5, xmp.iid:7C6572D2A3A0DF11A0EBDF2010A5A5C5, xmp.iid:7E6572D2A3A0DF11A0EBDF2010A5A5C5, xmp.iid:2AB4E82EA9A0DF11A0EBDF2010A5A5C5, xmp.iid:2BB4E82EA9A0DF11A0EBDF2010A5A5C5, xmp.iid:2CB4E82EA9A0DF11A0EBDF2010A5A5C5, xmp.iid:2DB4E82EA9A0DF11A0EBDF2010A5A5C5, xmp.iid:2FB4E82EA9A0DF11A0EBDF2010A5A5C5, xmp.iid:30B4E82EA9A0DF11A0EBDF2010A5A5C5, xmp.iid:31B4E82EA9A0DF11A0EBDF2010A5A5C5, xmp.iid:0DCD9243D4A0DF11B9F6F770A2CB4A9A, xmp.iid:352726741FA6DF1190A1AF341E9B9729, xmp.iid:362726741FA6DF1190A1AF341E9B9729, xmp.iid:372726741FA6DF1190A1AF341E9B9729, xmp.iid:382726741FA6DF1190A1AF341E9B9729, xmp.iid:392726741FA6DF1190A1AF341E9B9729, xmp.iid:3A2726741FA6DF1190A1AF341E9B9729, xmp.iid:3B2726741FA6DF1190A1AF341E9B9729, xmp.iid:3C2726741FA6DF1190A1AF341E9B9729, xmp.iid:3D2726741FA6DF1190A1AF341E9B9729, xmp.iid:3E2726741FA6DF1190A1AF341E9B9729, xmp.iid:1E59168E27A6DF1190A1AF341E9B9729, xmp.iid:1F59168E27A6DF1190A1AF341E9B9729, xmp.iid:2059168E27A6DF1190A1AF341E9B9729, xmp.iid:2159168E27A6DF1190A1AF341E9B9729, xmp.iid:2259168E27A6DF1190A1AF341E9B9729, xmp.iid:2359168E27A6DF1190A1AF341E9B9729, xmp.iid:2459168E27A6DF1190A1AF341E9B9729, xmp.iid:2559168E27A6DF1190A1AF341E9B9729, xmp.iid:2759168E27A6DF1190A1AF341E9B9729, xmp.iid:2859168E27A6DF1190A1AF341E9B9729, xmp.iid:D302F7EA32A6DF1190A1AF341E9B9729, xmp.iid:D402F7EA32A6DF1190A1AF341E9B9729, xmp.iid:D502F7EA32A6DF1190A1AF341E9B9729, xmp.iid:D602F7EA32A6DF1190A1AF341E9B9729, xmp.iid:D702F7EA32A6DF1190A1AF341E9B9729, xmp.iid:D802F7EA32A6DF1190A1AF341E9B9729, xmp.iid:5B78E95C42A6DF11B3A2D7E3C66C960A, xmp.iid:5C78E95C42A6DF11B3A2D7E3C66C960A, xmp.iid:5D78E95C42A6DF11B3A2D7E3C66C960A, xmp.iid:5E78E95C42A6DF11B3A2D7E3C66C960A, xmp.iid:5F78E95C42A6DF11B3A2D7E3C66C960A, xmp.iid:6078E95C42A6DF11B3A2D7E3C66C960A, xmp.iid:6178E95C42A6DF11B3A2D7E3C66C960A, xmp.iid:6278E95C42A6DF11B3A2D7E3C66C960A, xmp.iid:6478E95C42A6DF11B3A2D7E3C66C960A, xmp.iid:97F6F0EC47A6DF11B3A2D7E3C66C960A, xmp.iid:98F6F0EC47A6DF11B3A2D7E3C66C960A, xmp.iid:99F6F0EC47A6DF11B3A2D7E3C66C960A, xmp.iid:99EE00428CABDF11ABCF943AD0A92A0A, xmp.iid:9AEE00428CABDF11ABCF943AD0A92A0A, xmp.iid:B0BDCB5BA7ABDF118E69E00135F16C63, xmp.iid:264012F6B2AFDF119E2FA05A29743841, xmp.iid:274012F6B2AFDF119E2FA05A29743841, xmp.iid:284012F6B2AFDF119E2FA05A29743841, xmp.iid:294012F6B2AFDF119E2FA05A29743841, xmp.iid:2A4012F6B2AFDF119E2FA05A29743841, xmp.iid:2B4012F6B2AFDF119E2FA05A29743841, xmp.iid:2C4012F6B2AFDF119E2FA05A29743841, xmp.iid:2D4012F6B2AFDF119E2FA05A29743841, xmp.iid:E0424CF9C3AFDF119E2FA05A29743841, xmp.iid:E1424CF9C3AFDF119E2FA05A29743841, xmp.iid:E2424CF9C3AFDF119E2FA05A29743841, xmp.iid:E3424CF9C3AFDF119E2FA05A29743841, xmp.iid:E4424CF9C3AFDF119E2FA05A29743841, xmp.iid:E5424CF9C3AFDF119E2FA05A29743841, xmp.iid:E6424CF9C3AFDF119E2FA05A29743841, xmp.iid:E7424CF9C3AFDF119E2FA05A29743841, xmp.iid:E8424CF9C3AFDF119E2FA05A29743841, xmp.iid:E9424CF9C3AFDF119E2FA05A29743841, xmp.iid:EA424CF9C3AFDF119E2FA05A29743841, xmp.iid:E5C0ACECCAAFDF119E2FA05A29743841, xmp.iid:E6C0ACECCAAFDF119E2FA05A29743841, xmp.iid:E7C0ACECCAAFDF119E2FA05A29743841, xmp.iid:FAD9844B48B0DF11BB15905F2D6E8D28, xmp.iid:FBD9844B48B0DF11BB15905F2D6E8D28, xmp.iid:FCD9844B48B0DF11BB15905F2D6E8D28, xmp.iid:FDD9844B48B0DF11BB15905F2D6E8D28, xmp.iid:FED9844B48B0DF11BB15905F2D6E8D28, xmp.iid:FFD9844B48B0DF11BB15905F2D6E8D28, xmp.iid:00DA844B48B0DF11BB15905F2D6E8D28, xmp.iid:01DA844B48B0DF11BB15905F2D6E8D28, xmp.iid:02DA844B48B0DF11BB15905F2D6E8D28, xmp.iid:03DA844B48B0DF11BB15905F2D6E8D28, xmp.iid:01E70B924CB0DF11BB15905F2D6E8D28, xmp.iid:02E70B924CB0DF11BB15905F2D6E8D28, xmp.iid:03E70B924CB0DF11BB15905F2D6E8D28, xmp.iid:04E70B924CB0DF11BB15905F2D6E8D28, xmp.iid:05E70B924CB0DF11BB15905F2D6E8D28, xmp.iid:06E70B924CB0DF11BB15905F2D6E8D28, xmp.iid:07E70B924CB0DF11BB15905F2D6E8D28, xmp.iid:08E70B924CB0DF11BB15905F2D6E8D28, xmp.iid:09E70B924CB0DF11BB15905F2D6E8D28, xmp.iid:0AE70B924CB0DF11BB15905F2D6E8D28, xmp.iid:0BE70B924CB0DF11BB15905F2D6E8D28, xmp.iid:16BF5009DBB1DF11A95ED6A123401F25, xmp.iid:17BF5009DBB1DF11A95ED6A123401F25, xmp.iid:E1C938ADE3B1DF11A95ED6A123401F25, xmp.iid:E2C938ADE3B1DF11A95ED6A123401F25, xmp.iid:E3C938ADE3B1DF11A95ED6A123401F25, xmp.iid:E4C938ADE3B1DF11A95ED6A123401F25, xmp.iid:E5C938ADE3B1DF11A95ED6A123401F25, xmp.iid:E6C938ADE3B1DF11A95ED6A123401F25, xmp.iid:E7C938ADE3B1DF11A95ED6A123401F25, xmp.iid:E8C938ADE3B1DF11A95ED6A123401F25, xmp.iid:E9C938ADE3B1DF11A95ED6A123401F25, xmp.iid:EAC938ADE3B1DF11A95ED6A123401F25, xmp.iid:42238FCF0FB2DF11A95ED6A123401F25, xmp.iid:43238FCF0FB2DF11A95ED6A123401F25, xmp.iid:44238FCF0FB2DF11A95ED6A123401F25, xmp.iid:45238FCF0FB2DF11A95ED6A123401F25, xmp.iid:46238FCF0FB2DF11A95ED6A123401F25, xmp.iid:47238FCF0FB2DF11A95ED6A123401F25, xmp.iid:FCBAC32E14B2DF11A95ED6A123401F25, xmp.iid:FDBAC32E14B2DF11A95ED6A123401F25, xmp.iid:FEBAC32E14B2DF11A95ED6A123401F25, xmp.iid:01C8AD3018B2DF1192EDFC74ECE4DD5A, xmp.iid:02C8AD3018B2DF1192EDFC74ECE4DD5A, xmp.iid:03C8AD3018B2DF1192EDFC74ECE4DD5A, xmp.iid:04C8AD3018B2DF1192EDFC74ECE4DD5A, xmp.iid:05C8AD3018B2DF1192EDFC74ECE4DD5A, xmp.iid:B5EF497E2FB4DF118E42A5494D4648E1, xmp.iid:B6EF497E2FB4DF118E42A5494D4648E1, xmp.iid:B7EF497E2FB4DF118E42A5494D4648E1, xmp.iid:B8EF497E2FB4DF118E42A5494D4648E1, xmp.iid:B9EF497E2FB4DF118E42A5494D4648E1, xmp.iid:BAEF497E2FB4DF118E42A5494D4648E1, xmp.iid:BBEF497E2FB4DF118E42A5494D4648E1, xmp.iid:BCEF497E2FB4DF118E42A5494D4648E1, xmp.iid:F3C06B6A9CB7DF11A6D98ADE52708029, xmp.iid:F4C06B6A9CB7DF11A6D98ADE52708029, xmp.iid:F5C06B6A9CB7DF11A6D98ADE52708029, xmp.iid:F6C06B6A9CB7DF11A6D98ADE52708029
History When                    : 2010:02:01 13:24:07-06:00, 2010:02:01 13:24:07-06:00, 2010:02:01 13:29:57-06:00, 2010:02:01 13:31:30-06:00, 2010:02:01 13:32:18-06:00, 2010:02:01 13:32:18-06:00, 2010:02:01 13:40:51-06:00, 2010:02:01 13:40:51-06:00, 2010:02:01 14:44:37-06:00, 2010:02:01 14:44:37-06:00, 2010:02:02 09:03:30-06:00, 2010:02:02 09:03:30-06:00, 2010:02:02 11:25:55-06:00, 2010:02:02 11:25:55-06:00, 2010:02:02 13:34:57-06:00, 2010:02:02 13:34:57-06:00, 2010:02:02 14:54:25-06:00, 2010:02:02 14:54:25-06:00, 2010:02:02 15:21:41-06:00, 2010:02:02 15:21:41-06:00, 2010:02:02 15:26:39-06:00, 2010:02:02 15:26:39-06:00, 2010:02:02 15:34:44-06:00, 2010:02:02 15:34:44-06:00, 2010:02:02 15:46:31-06:00, 2010:02:02 15:46:31-06:00, 2010:03:02 10:04:07-06:00, 2010:03:02 10:04:07-06:00, 2010:03:02 10:06:42-06:00, 2010:03:02 10:06:42-06:00, 2010:03:02 10:07:43-06:00, 2010:03:02 10:07:43-06:00, 2010:03:02 10:13:39-06:00, 2010:03:02 10:13:39-06:00, 2010:03:03 10:43:11-06:00, 2010:03:03 10:43:11-06:00, 2010:03:03 10:53:35-06:00, 2010:03:03 10:53:35-06:00, 2010:03:03 10:54:28-06:00, 2010:03:03 10:54:28-06:00, 2010:03:03 13:50:36-06:00, 2010:03:03 14:58:15-06:00, 2010:03:03 14:58:15-06:00, 2010:03:03 15:45:55-06:00, 2010:03:03 15:45:55-06:00, 2010:03:05 10:28:55-06:00, 2010:03:05 10:28:55-06:00, 2010:03:05 10:41:06-06:00, 2010:03:05 10:41:06-06:00, 2010:03:05 11:01:07-06:00, 2010:03:05 11:01:07-06:00, 2010:03:10 14:28:52-06:00, 2010:03:10 14:28:53-06:00, 2010:03:10 15:38:44-06:00, 2010:03:10 15:38:45-06:00, 2010:03:10 15:39:56-06:00, 2010:03:10 15:39:56-06:00, 2010:03:10 15:43:20-06:00, 2010:03:10 15:43:20-06:00, 2010:03:11 07:57:07-06:00, 2010:03:11 08:04:28-06:00, 2010:03:11 08:05:28-06:00, 2010:03:11 08:06:28-06:00, 2010:03:22 15:39:08-05:00, 2010:03:22 15:39:08-05:00, 2010:03:23 15:50:54-05:00, 2010:03:23 15:50:54-05:00, 2010:03:23 15:51:33-05:00, 2010:04:14 16:27:59-05:00, 2010:04:21 14:54:04-05:00, 2010:04:21 14:54:04-05:00, 2010:04:22 11:21:34-05:00, 2010:04:22 11:21:34-05:00, 2010:04:22 13:30:57-05:00, 2010:04:22 13:30:57-05:00, 2010:04:22 14:05:57-05:00, 2010:05:06 10:31:37-05:00, 2010:05:06 10:31:37-05:00, 2010:05:06 11:27:42-05:00, 2010:05:06 11:27:42-05:00, 2010:05:06 13:41:29-05:00, 2010:05:06 13:41:29-05:00, 2010:05:06 14:18:02-05:00, 2010:05:06 14:18:02-05:00, 2010:05:07 10:28:22-05:00, 2010:05:07 10:28:22-05:00, 2010:05:07 11:05:27-05:00, 2010:05:07 11:05:27-05:00, 2010:05:07 11:10:03-05:00, 2010:05:07 11:10:03-05:00, 2010:05:24 14:15:02-05:00, 2010:05:24 14:15:02-05:00, 2010:05:24 14:24:04-05:00, 2010:05:24 14:24:04-05:00, 2010:05:24 15:06:39-05:00, 2010:05:24 15:06:39-05:00, 2010:05:26 10:21:52-05:00, 2010:05:26 10:21:52-05:00, 2010:05:26 16:04:47-05:00, 2010:05:26 16:04:47-05:00, 2010:05:28 14:37:20-05:00, 2010:05:28 14:37:20-05:00, 2010:05:28 14:40:10-05:00, 2010:05:28 14:40:10-05:00, 2010:06:01 13:50:40-05:00, 2010:06:01 13:50:40-05:00, 2010:06:01 14:23:43-05:00, 2010:06:01 14:23:43-05:00, 2010:06:01 15:19:20-05:00, 2010:06:01 15:19:20-05:00, 2010:06:02 15:52:01-05:00, 2010:06:02 15:52:53-05:00, 2010:06:02 15:52:53-05:00, 2010:06:02 15:53:52-05:00, 2010:06:02 15:53:52-05:00, 2010:06:21 09:37:29-05:00, 2010:06:21 09:37:29-05:00, 2010:06:21 10:46:32-05:00, 2010:06:21 10:46:32-05:00, 2010:06:21 10:56:29-05:00, 2010:06:21 10:56:29-05:00, 2010:06:21 11:05:47-05:00, 2010:06:21 11:05:47-05:00, 2010:06:30 17:56:47-05:00, 2010:06:30 17:56:47-05:00, 2010:07:01 17:01:07-05:00, 2010:07:01 17:01:07-05:00, 2010:07:01 17:04:09-05:00, 2010:07:01 17:04:09-05:00, 2010:07:14 12:40:09-05:00, 2010:07:14 12:40:09-05:00, 2010:07:14 13:29:59-05:00, 2010:07:14 13:29:59-05:00, 2010:07:14 13:39:47-05:00, 2010:07:14 13:39:47-05:00, 2010:07:15 15:57:40-05:00, 2010:07:15 15:57:41-05:00, 2010:07:16 10:28:36-05:00, 2010:07:16 10:28:36-05:00, 2010:07:16 11:14:40-05:00, 2010:07:16 11:14:40-05:00, 2010:07:16 15:42:37-05:00, 2010:07:16 15:42:37-05:00, 2010:07:20 15:58:46-05:00, 2010:07:20 15:58:46-05:00, 2010:07:20 15:59:32-05:00, 2010:07:20 15:59:32-05:00, 2010:07:29 10:16:50-05:00, 2010:07:29 10:18:39-05:00, 2010:07:29 10:20:17-05:00, 2010:07:29 10:20:17-05:00, 2010:07:30 13:35:38-05:00, 2010:07:30 13:50:29-05:00, 2010:07:30 13:55:56-05:00, 2010:07:30 13:58:06-05:00, 2010:07:30 13:59:25-05:00, 2010:07:30 14:14:57-05:00, 2010:07:30 14:19:12-05:00, 2010:07:30 14:22:26-05:00, 2010:07:30 14:32-05:00, 2010:07:30 14:35:09-05:00, 2010:07:30 14:38:27-05:00, 2010:07:30 14:51:13-05:00, 2010:07:30 14:53:31-05:00, 2010:07:30 15:44:02-05:00, 2010:07:30 15:44:11-05:00, 2010:07:30 15:44:26-05:00, 2010:07:30 16:12:15-05:00, 2010:08:02 10:53:34-05:00, 2010:08:02 11:23:40-05:00, 2010:08:02 11:30:21-05:00, 2010:08:02 11:34:11-05:00, 2010:08:02 11:51:20-05:00, 2010:08:02 13:10:14-05:00, 2010:08:02 13:10:34-05:00, 2010:08:02 13:11:25-05:00, 2010:08:02 13:25:01-05:00, 2010:08:02 14:34:06-05:00, 2010:08:02 14:38:24-05:00, 2010:08:02 14:38:44-05:00, 2010:08:02 14:40:23-05:00, 2010:08:02 14:44:11-05:00, 2010:08:02 14:49:30-05:00, 2010:08:02 14:51:31-05:00, 2010:08:02 14:54:28-05:00, 2010:08:02 14:55:56-05:00, 2010:08:02 14:56:17-05:00, 2010:08:02 14:57:23-05:00, 2010:08:02 15:00:02-05:00, 2010:08:02 15:01:03-05:00, 2010:08:02 15:08:48-05:00, 2010:08:02 15:15:56-05:00, 2010:08:02 15:19:01-05:00, 2010:08:02 15:23:27-05:00, 2010:08:02 15:23:40-05:00, 2010:08:02 15:29:59-05:00, 2010:08:02 15:31:49-05:00, 2010:08:02 15:32:14-05:00, 2010:08:02 15:38:38-05:00, 2010:08:02 15:39-05:00, 2010:08:02 15:41:51-05:00, 2010:08:02 15:56:53-05:00, 2010:08:02 15:57:58-05:00, 2010:08:02 16:24:45-05:00, 2010:08:02 16:33:26-05:00, 2010:08:02 16:34:32-05:00, 2010:08:02 16:41:05-05:00, 2010:08:02 16:41:39-05:00, 2010:08:03 08:42:55-05:00, 2010:08:03 08:43:19-05:00, 2010:08:03 08:57:40-05:00, 2010:08:03 09:02:46-05:00, 2010:08:03 09:07:57-05:00, 2010:08:03 09:12:39-05:00, 2010:08:03 09:18:38-05:00, 2010:08:03 09:37:55-05:00, 2010:08:03 09:40:01-05:00, 2010:08:03 10:08:44-05:00, 2010:08:03 10:09:27-05:00, 2010:08:03 10:14:58-05:00, 2010:08:03 10:15:36-05:00, 2010:08:03 10:17-05:00, 2010:08:03 10:17:26-05:00, 2010:08:03 10:22:42-05:00, 2010:08:03 10:38:55-05:00, 2010:08:03 10:43:43-05:00, 2010:08:03 10:49:38-05:00, 2010:08:03 10:58:51-05:00, 2010:08:03 11:02:42-05:00, 2010:08:03 11:09:40-05:00, 2010:08:03 11:11:52-05:00, 2010:08:03 11:13:20-05:00, 2010:08:03 11:13:42-05:00, 2010:08:03 11:20:18-05:00, 2010:08:03 11:21:48-05:00, 2010:08:03 11:28:39-05:00, 2010:08:03 11:30:54-05:00, 2010:08:03 11:32:39-05:00, 2010:08:03 11:43:29-05:00, 2010:08:03 11:45:43-05:00, 2010:08:03 11:48:26-05:00, 2010:08:03 11:50-05:00, 2010:08:03 12:55:21-05:00, 2010:08:03 12:59:03-05:00, 2010:08:03 13:03:14-05:00, 2010:08:03 13:05:11-05:00, 2010:08:03 13:13:13-05:00, 2010:08:03 13:15:50-05:00, 2010:08:03 13:30:09-05:00, 2010:08:03 13:30:38-05:00, 2010:08:03 13:38:08-05:00, 2010:08:03 13:45:55-05:00, 2010:08:03 13:54:23-05:00, 2010:08:03 13:55:48-05:00, 2010:08:03 13:58:36-05:00, 2010:08:03 14:02:14-05:00, 2010:08:03 14:03:07-05:00, 2010:08:03 14:04:29-05:00, 2010:08:03 14:06:22-05:00, 2010:08:03 14:25:53-05:00, 2010:08:03 14:32:56-05:00, 2010:08:03 15:53:24-05:00, 2010:08:03 15:59:19-05:00, 2010:08:03 16:00:58-05:00, 2010:08:03 16:05:14-05:00, 2010:08:03 16:08:59-05:00, 2010:08:03 16:09:34-05:00, 2010:08:04 08:08:24-05:00, 2010:08:04 08:18:01-05:00, 2010:08:04 08:23:29-05:00, 2010:08:04 08:24:39-05:00, 2010:08:04 08:26:20-05:00, 2010:08:04 08:27:55-05:00, 2010:08:04 08:34:28-05:00, 2010:08:04 09:30:26-05:00, 2010:08:04 09:43:48-05:00, 2010:08:04 09:44:32-05:00, 2010:08:04 09:45:17-05:00, 2010:08:04 09:56:55-05:00, 2010:08:04 09:59:31-05:00, 2010:08:04 10:10:50-05:00, 2010:08:04 10:15-05:00, 2010:08:04 10:16:06-05:00, 2010:08:04 10:18:22-05:00, 2010:08:04 10:20:05-05:00, 2010:08:04 10:28:28-05:00, 2010:08:04 10:29:31-05:00, 2010:08:04 10:38:14-05:00, 2010:08:04 10:54:37-05:00, 2010:08:04 10:55:10-05:00, 2010:08:04 11:00:38-05:00, 2010:08:04 11:24:47-05:00, 2010:08:04 11:26:48-05:00, 2010:08:04 11:28:04-05:00, 2010:08:04 11:30:13-05:00, 2010:08:04 11:32:23-05:00, 2010:08:04 11:33:39-05:00, 2010:08:04 11:35:26-05:00, 2010:08:04 11:36:29-05:00, 2010:08:04 11:37:58-05:00, 2010:08:04 11:39:43-05:00, 2010:08:04 11:42:40-05:00, 2010:08:04 11:43:44-05:00, 2010:08:04 11:44:21-05:00, 2010:08:04 11:45:04-05:00, 2010:08:04 11:45:25-05:00, 2010:08:04 11:45:56-05:00, 2010:08:04 13:04:19-05:00, 2010:08:04 13:07-05:00, 2010:08:04 13:07:10-05:00, 2010:08:04 13:49:01-05:00, 2010:08:04 14:48:24-05:00, 2010:08:04 14:57:11-05:00, 2010:08:04 15:12:07-05:00, 2010:08:04 15:47-05:00, 2010:08:04 15:51:04-05:00, 2010:08:04 15:55:34-05:00, 2010:08:04 16:00:04-05:00, 2010:08:04 16:01:29-05:00, 2010:08:05 07:07:18-05:00, 2010:08:05 07:20:31-05:00, 2010:08:05 08:44:29-05:00, 2010:08:05 08:45:05-05:00, 2010:08:05 08:52:43-05:00, 2010:08:05 08:53:33-05:00, 2010:08:05 08:54:23-05:00, 2010:08:05 08:56:12-05:00, 2010:08:05 09:08:13-05:00, 2010:08:05 09:15:01-05:00, 2010:08:05 09:29:46-05:00, 2010:08:05 09:36:42-05:00, 2010:08:05 09:51:07-05:00, 2010:08:05 09:57:04-05:00, 2010:08:05 10:10:44-05:00, 2010:08:05 10:12:11-05:00, 2010:08:05 10:18:46-05:00, 2010:08:05 10:19:06-05:00, 2010:08:05 10:19:55-05:00, 2010:08:05 10:30:08-05:00, 2010:08:05 10:30:59-05:00, 2010:08:05 10:32:02-05:00, 2010:08:05 10:35:45-05:00, 2010:08:05 10:37:20-05:00, 2010:08:05 10:47:41-05:00, 2010:08:05 10:50:34-05:00, 2010:08:05 10:56:48-05:00, 2010:08:05 10:58:45-05:00, 2010:08:05 11:13:37-05:00, 2010:08:05 11:17:01-05:00, 2010:08:05 11:18:09-05:00, 2010:08:05 11:24:37-05:00, 2010:08:05 15:58:57-05:00, 2010:08:12 09:39:46-05:00, 2010:08:12 09:45:44-05:00, 2010:08:12 09:47-05:00, 2010:08:12 09:55:38-05:00, 2010:08:12 09:57:07-05:00, 2010:08:12 09:58:36-05:00, 2010:08:12 10:10:46-05:00, 2010:08:12 10:17:08-05:00, 2010:08:12 10:18:57-05:00, 2010:08:12 10:29:41-05:00, 2010:08:12 10:37:46-05:00, 2010:08:12 10:38:26-05:00, 2010:08:12 11:20:07-05:00, 2010:08:12 11:32:31-05:00, 2010:08:12 11:41-05:00, 2010:08:12 11:44:51-05:00, 2010:08:12 11:45:48-05:00, 2010:08:12 11:48:04-05:00, 2010:08:12 11:51:11-05:00, 2010:08:12 11:58:22-05:00, 2010:08:12 11:59:06-05:00, 2010:08:12 12:01:04-05:00, 2010:08:12 13:11:18-05:00, 2010:08:12 13:12:20-05:00, 2010:08:12 13:12:57-05:00, 2010:08:12 13:12:58-05:00, 2010:08:12 13:49:40-05:00, 2010:08:12 14:06:58-05:00, 2010:08:12 14:07:54-05:00, 2010:08:12 14:13:09-05:00, 2010:08:12 14:15:30-05:00, 2010:08:12 14:19:28-05:00, 2010:08:12 14:23:08-05:00, 2010:08:12 14:25:58-05:00, 2010:08:12 14:28:57-05:00, 2010:08:12 14:29:29-05:00, 2010:08:12 14:29:50-05:00, 2010:08:12 14:30:45-05:00, 2010:08:19 09:38:58-05:00, 2010:08:19 09:40:34-05:00, 2010:08:19 10:35:13-05:00, 2010:08:24 14:42:49-05:00, 2010:08:24 14:55:10-05:00, 2010:08:24 14:59:34-05:00, 2010:08:24 15:05:33-05:00, 2010:08:24 15:27:39-05:00, 2010:08:24 15:28:44-05:00, 2010:08:24 15:50:36-05:00, 2010:08:24 16:07:02-05:00, 2010:08:24 16:10:08-05:00, 2010:08:24 16:11:58-05:00, 2010:08:24 16:25:27-05:00, 2010:08:24 16:25:50-05:00, 2010:08:24 16:26:28-05:00, 2010:08:24 16:34:06-05:00, 2010:08:24 16:37:51-05:00, 2010:08:24 16:51-05:00, 2010:08:24 16:52:09-05:00, 2010:08:24 16:53:23-05:00, 2010:08:24 16:53:44-05:00, 2010:08:24 16:59:53-05:00, 2010:08:24 17:04:31-05:00, 2010:08:24 17:04:47-05:00, 2010:08:25 07:57:19-05:00, 2010:08:25 07:58:41-05:00, 2010:08:25 07:59-05:00, 2010:08:25 08:03:47-05:00, 2010:08:25 08:06-05:00, 2010:08:25 08:07:19-05:00, 2010:08:25 08:08:07-05:00, 2010:08:25 08:14:21-05:00, 2010:08:25 08:16:06-05:00, 2010:08:25 08:17:14-05:00, 2010:08:25 08:27:55-05:00, 2010:08:25 08:31:51-05:00, 2010:08:25 08:54:02-05:00, 2010:08:25 08:56:24-05:00, 2010:08:25 09:11:36-05:00, 2010:08:25 09:13:11-05:00, 2010:08:25 09:16:09-05:00, 2010:08:25 09:56:18-05:00, 2010:08:25 10:05:05-05:00, 2010:08:25 10:10:03-05:00, 2010:08:25 10:55-05:00, 2010:08:27 08:55:02-05:00, 2010:08:27 09:01-05:00, 2010:08:27 09:02:06-05:00, 2010:08:27 09:03:04-05:00, 2010:08:27 09:09:30-05:00, 2010:08:27 09:22:12-05:00, 2010:08:27 09:22:44-05:00, 2010:08:27 09:26:04-05:00, 2010:08:27 09:33:18-05:00, 2010:08:27 09:40:12-05:00, 2010:08:27 09:41:41-05:00, 2010:08:27 09:45:09-05:00, 2010:08:27 14:41:35-05:00, 2010:08:27 14:43:09-05:00, 2010:08:27 14:44:39-05:00, 2010:08:27 14:45:04-05:00, 2010:08:27 14:45:18-05:00, 2010:08:27 14:47:22-05:00, 2010:08:27 14:49:19-05:00, 2010:08:27 14:50:01-05:00, 2010:08:27 14:50:01-05:00, 2010:08:27 15:18:01-05:00, 2010:08:27 15:18:13-05:00, 2010:08:27 15:19:55-05:00, 2010:08:27 15:27:48-05:00, 2010:08:27 15:45:30-05:00, 2010:08:30 07:09:51-05:00, 2010:08:30 07:10:51-05:00, 2010:08:30 07:13:43-05:00, 2010:08:30 07:15:38-05:00, 2010:08:30 07:18:07-05:00, 2010:08:30 07:24:23-05:00, 2010:08:30 07:25:24-05:00, 2010:08:30 07:25:25-05:00, 2010:09:03 15:47:07-05:00, 2010:09:03 15:48:32-05:00, 2010:09:03 15:53:05-05:00, 2010:09:03 15:53:31-05:00
History Software Agent          : Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0
History Changed                 : /, /metadata, /, /, /metadata, /, /, /metadata, /metadata, /, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /, /, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /, /, /, /, /metadata, /;/metadata, /metadata, /;/metadata, /, /, /metadata, /, /metadata, /;/metadata, /metadata, /;/metadata, /, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /, /, /, /metadata, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /metadata, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /metadata, /, /, /, /, /, /, /, /, /, /, /, /, /metadata, /, /, /, /, /
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 96.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 300.00, 72.00, 300.00, 72.00, 72.00, 300.00, 300.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 72.00, 72.00
Manifest Placed Y Resolution    : 96.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 300.00, 72.00, 300.00, 72.00, 72.00, 300.00, 300.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 72.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches
Manifest Reference Instance ID  : xmp.iid:279B21C20A9CDF118A76CEAEDE48B9CC, uuid:E6AEABE5B3CEDC11994ED086F49484E2, uuid:E6AEABE5B3CEDC11994ED086F49484E2, uuid:E6AEABE5B3CEDC11994ED086F49484E2, uuid:E6AEABE5B3CEDC11994ED086F49484E2, uuid:E6AEABE5B3CEDC11994ED086F49484E2, uuid:596fb0bd-8ce4-4325-a391-48314e83b2a8, uuid:aebc1017-83f5-4758-9bb5-f9c538f46c79, uuid:d7b5ba3b-47ec-4bc1-86d5-020d23271c82, uuid:ad45af7d-3aac-4428-bc90-ee92aae91d07, uuid:E6AEABE5B3CEDC11994ED086F49484E2, uuid:f6f7f9a6-dd8b-4a73-84a2-296fac7a8eb2, uuid:f6f7f9a6-dd8b-4a73-84a2-296fac7a8eb2, uuid:f6f7f9a6-dd8b-4a73-84a2-296fac7a8eb2, uuid:f6f7f9a6-dd8b-4a73-84a2-296fac7a8eb2, uuid:E6AEABE5B3CEDC11994ED086F49484E2, uuid:595e6946-94d4-44d8-b3b4-50545d88e819, uuid:E6AEABE5B3CEDC11994ED086F49484E2, uuid:de6b9941-709e-45f3-b10d-5d3822f6763f, uuid:de6b9941-709e-45f3-b10d-5d3822f6763f, uuid:2b081e8c-c511-4069-818e-a1199e4106dc, uuid:2b081e8c-c511-4069-818e-a1199e4106dc, uuid:E6AEABE5B3CEDC11994ED086F49484E2, uuid:0e2809ad-84d3-4591-916b-c58e8a86a07f, uuid:0e2809ad-84d3-4591-916b-c58e8a86a07f, uuid:E6AEABE5B3CEDC11994ED086F49484E2, xmp.iid:15FB75A5F29FDF119C2EAA0C7F11EE62, xmp.iid:15FB75A5F29FDF119C2EAA0C7F11EE62, uuid:0e2809ad-84d3-4591-916b-c58e8a86a07f, uuid:43F04F414CE9DC119772FDB356A4D3A2, uuid:E6AEABE5B3CEDC11994ED086F49484E2, xmp.iid:EFE11A12539EDF11BFB3A7D84F9C0840, uuid:46519F0E60E9DC119772FDB356A4D3A2, uuid:46519F0E60E9DC119772FDB356A4D3A2, uuid:46519F0E60E9DC119772FDB356A4D3A2, uuid:E6AEABE5B3CEDC11994ED086F49484E2, uuid:5ABF9BD99AE0DC11A3CED95470FA3DBF, uuid:e86aad68-0975-4a3e-b93e-2769f8dc8e10, uuid:e86aad68-0975-4a3e-b93e-2769f8dc8e10, uuid:E6AEABE5B3CEDC11994ED086F49484E2, uuid:aeda5c87-0471-425b-8ffd-13056d6dd2f3, uuid:6a563ffd-e274-4438-a0b7-afa3d99b2649, uuid:E6AEABE5B3CEDC11994ED086F49484E2, uuid:fc427b1b-6932-4d0b-933a-3cb1bdd053fe, uuid:fc427b1b-6932-4d0b-933a-3cb1bdd053fe, uuid:7cdfa82e-99f9-414b-908d-7312c2bb2eea, uuid:E6AEABE5B3CEDC11994ED086F49484E2, uuid:43F04F414CE9DC119772FDB356A4D3A2, uuid:E6AEABE5B3CEDC11994ED086F49484E2, uuid:cd1e9e37-ea85-4198-802f-d1509014e832, xmp.iid:6A19B186189FDF118AB6FCD41D4AE218, xmp.iid:0E811B6F0D9FDF118AB6FCD41D4AE218, uuid:E6AEABE5B3CEDC11994ED086F49484E2, xmp.iid:2467622D279BDF118151E0356925F5E7, uuid:E6AEABE5B3CEDC11994ED086F49484E2, uuid:E6AEABE5B3CEDC11994ED086F49484E2, xmp.iid:0E1E56BC99A0DF11A6E49B16B99F8EB5, xmp.iid:2A67622D279BDF118151E0356925F5E7, uuid:E6AEABE5B3CEDC11994ED086F49484E2, uuid:37f41f31-6f9b-4486-a77e-b971ee5c1f45, uuid:37f41f31-6f9b-4486-a77e-b971ee5c1f45, uuid:E6AEABE5B3CEDC11994ED086F49484E2, xmp.iid:6D19B186189FDF118AB6FCD41D4AE218, uuid:31a028e0-5d13-47fd-9e58-f758f6d6a6d7, uuid:E6AEABE5B3CEDC11994ED086F49484E2, uuid:1923D535B9E3DC11B31C841FD8A3A821, uuid:E6AEABE5B3CEDC11994ED086F49484E2, uuid:c666ee14-8f55-4c6a-8c59-b50cdc30b282, uuid:c666ee14-8f55-4c6a-8c59-b50cdc30b282, uuid:E6AEABE5B3CEDC11994ED086F49484E2, uuid:ea7c8e89-08e3-4b11-8007-e9d09917070a, uuid:E6AEABE5B3CEDC11994ED086F49484E2, xmp.iid:068C2B8A269BDF118151E0356925F5E7, xmp.iid:0B8C2B8A269BDF118151E0356925F5E7, xmp.iid:088C2B8A269BDF118151E0356925F5E7, xmp.iid:2C67622D279BDF118151E0356925F5E7, xmp.iid:E7A00430269BDF118151E0356925F5E7, xmp.iid:5B17DD94279BDF118151E0356925F5E7, xmp.iid:EBA00430269BDF118151E0356925F5E7, uuid:E6AEABE5B3CEDC11994ED086F49484E2, uuid:E6AEABE5B3CEDC11994ED086F49484E2
Manifest Reference Document ID  : uuid:C09F4DE64FE3DD11A517C9625CDDA337, uuid:E5AEABE5B3CEDC11994ED086F49484E2, uuid:E5AEABE5B3CEDC11994ED086F49484E2, uuid:E5AEABE5B3CEDC11994ED086F49484E2, uuid:E5AEABE5B3CEDC11994ED086F49484E2, uuid:E5AEABE5B3CEDC11994ED086F49484E2, xmp.did:A12F21423681DE11B520DFDECF0D185F, xmp.did:A22F21423681DE11B520DFDECF0D185F, xmp.did:12D64D9D42A6DF11B1239E258562A039, xmp.did:14E6A7E3129CDF119582F8B8FBF03DBE, uuid:E5AEABE5B3CEDC11994ED086F49484E2, uuid:8b2f2ded-0fd1-4f63-a242-cf7d66138fa6, uuid:8b2f2ded-0fd1-4f63-a242-cf7d66138fa6, uuid:8b2f2ded-0fd1-4f63-a242-cf7d66138fa6, uuid:8b2f2ded-0fd1-4f63-a242-cf7d66138fa6, uuid:E5AEABE5B3CEDC11994ED086F49484E2, xmp.did:ECE11A12539EDF11BFB3A7D84F9C0840, uuid:E5AEABE5B3CEDC11994ED086F49484E2, uuid:69a43179-b513-4056-8650-1a34d14683f8, uuid:69a43179-b513-4056-8650-1a34d14683f8, xmp.did:EDE11A12539EDF11BFB3A7D84F9C0840, xmp.did:EDE11A12539EDF11BFB3A7D84F9C0840, uuid:E5AEABE5B3CEDC11994ED086F49484E2, xmp.did:EEE11A12539EDF11BFB3A7D84F9C0840, xmp.did:EEE11A12539EDF11BFB3A7D84F9C0840, uuid:E5AEABE5B3CEDC11994ED086F49484E2, xmp.did:15FB75A5F29FDF119C2EAA0C7F11EE62, xmp.did:15FB75A5F29FDF119C2EAA0C7F11EE62, xmp.did:EEE11A12539EDF11BFB3A7D84F9C0840, uuid:40F04F414CE9DC119772FDB356A4D3A2, uuid:E5AEABE5B3CEDC11994ED086F49484E2, xmp.did:EFE11A12539EDF11BFB3A7D84F9C0840, uuid:48F04F414CE9DC119772FDB356A4D3A2, uuid:48F04F414CE9DC119772FDB356A4D3A2, uuid:48F04F414CE9DC119772FDB356A4D3A2, uuid:E5AEABE5B3CEDC11994ED086F49484E2, uuid:59BF9BD99AE0DC11A3CED95470FA3DBF, uuid:f5755d5a-23f0-47ee-92d9-0a94da902fbf, uuid:f5755d5a-23f0-47ee-92d9-0a94da902fbf, uuid:E5AEABE5B3CEDC11994ED086F49484E2, xmp.did:F0E11A12539EDF11BFB3A7D84F9C0840, xmp.did:F1E11A12539EDF11BFB3A7D84F9C0840, uuid:E5AEABE5B3CEDC11994ED086F49484E2, xmp.did:F2E11A12539EDF11BFB3A7D84F9C0840, xmp.did:F2E11A12539EDF11BFB3A7D84F9C0840, uuid:0de7f672-f8ef-427c-abc1-ffac1cd9fa7d, uuid:E5AEABE5B3CEDC11994ED086F49484E2, uuid:40F04F414CE9DC119772FDB356A4D3A2, uuid:E5AEABE5B3CEDC11994ED086F49484E2, uuid:0afd5d6c-0e35-4940-b19c-2639df56ce3e, xmp.did:0F811B6F0D9FDF118AB6FCD41D4AE218, xmp.did:07811B6F0D9FDF118AB6FCD41D4AE218, uuid:E5AEABE5B3CEDC11994ED086F49484E2, xmp.did:0C8C2B8A269BDF118151E0356925F5E7, uuid:E5AEABE5B3CEDC11994ED086F49484E2, uuid:E5AEABE5B3CEDC11994ED086F49484E2, xmp.did:0D1E56BC99A0DF11A6E49B16B99F8EB5, xmp.did:2967622D279BDF118151E0356925F5E7, uuid:E5AEABE5B3CEDC11994ED086F49484E2, xmp.did:42101FF21F9FDF11A99285F4D1BACD61, xmp.did:42101FF21F9FDF11A99285F4D1BACD61, uuid:E5AEABE5B3CEDC11994ED086F49484E2, xmp.did:6B19B186189FDF118AB6FCD41D4AE218, xmp.did:43101FF21F9FDF11A99285F4D1BACD61, uuid:E5AEABE5B3CEDC11994ED086F49484E2, uuid:1823D535B9E3DC11B31C841FD8A3A821, uuid:E5AEABE5B3CEDC11994ED086F49484E2, xmp.did:F084528E8EA0DF11A4ACFCD51F9560E3, xmp.did:F084528E8EA0DF11A4ACFCD51F9560E3, uuid:E5AEABE5B3CEDC11994ED086F49484E2, uuid:a0acb214-4e08-49d9-bc45-a9bc0f5e80bd, uuid:E5AEABE5B3CEDC11994ED086F49484E2, xmp.did:058C2B8A269BDF118151E0356925F5E7, xmp.did:098C2B8A269BDF118151E0356925F5E7, xmp.did:078C2B8A269BDF118151E0356925F5E7, xmp.did:2B67622D279BDF118151E0356925F5E7, xmp.did:E6A00430269BDF118151E0356925F5E7, xmp.did:5A17DD94279BDF118151E0356925F5E7, xmp.did:EAA00430269BDF118151E0356925F5E7, uuid:E5AEABE5B3CEDC11994ED086F49484E2, uuid:E5AEABE5B3CEDC11994ED086F49484E2
Create Date                     : 2010:09:03 15:53:50-05:00
Modify Date                     : 2010:09:03 15:54:12-05:00
Metadata Date                   : 2010:09:03 15:54:12-05:00
Creator Tool                    : Adobe InDesign CS4 (6.0.5)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 9611 bytes, use -b option to extract)
Doc Change Count                : 42726
Format                          : application/pdf
Producer                        : Adobe PDF Library 9.0
Trapped                         : False
Page Count                      : 28
Creator                         : Adobe InDesign CS4 (6.0.5)

EXIF Metadata provided by EXIF.tools

Greenheck Fan Grease Grabber H2O Auto Cleaning Hood Ggh20 Users Manual

Grease Grabber H2O Auto-Cleaning Hood GGH20 473380GGH2O_iom

GGH20 to the manual 8b132d06-652c-4c26-999c-13c8794c5944

Navigation menu

Versions of this User Manual:

Views

Navigation