GuangZhou Walkera Technology DEVO-6 2.4G Transmitter User Manual S29DEVO 6

Download:
Mirror Download [FCC.gov]
Document ID	1560828
Application ID	wUxC5aaNsOtVleqlMsvbDQ==
Document Description	Users Manual 3of4
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	405.58kB (5069771 bits)
Date Submitted	2011-10-14 00:00:00
Date Available	2011-10-14 00:00:00
Creation Date	2011-10-14 10:41:25
Producing Software	ScanSoft PDF Create! 5
Document Lastmod	2011-10-14 10:47:54
Document Title	S29DEVO-6_user manual.pdf
Document Creator	S29DEVO-6_user manual.pdf
Document Author:	Frank

o'eUertJtion
DEVO 5 Welcome to use the DEVO-G transmitter
Take countdown manner as an example to explatn
(1) Selling fur Timer 1
(1.1) Timer 1 selling
Tuuch the navigattort mark of Ttmerfl and expand a dropdown of Stupwalch and Countdown. Select the
desired ttming method. The timing range of stopwatch ts from 010 59'59 (59 mtnutes 59 seconds).
(1.2) Switch selection
Touch the navtgattoh mark MSwttch and gel a selectable dropdown.
(1.3) Sel time
The sellable countdown time range ts from 00:05 tn 59:55.
(2) Selttng for Ttmer 2 IS same as that (or ttmer 1.
Touch the icon B IO extl afterfirttshed.
DEVD 5—38
All the funcmnal setlings, whwch are relative
Part three Evo-e use”.
AeUenLon Welcome to use the DEVO-S transmitter
DEVCI a
1 0 System menu
The boot screen of airplane is shown as below:
Elevator trlm Throttle trim
Transmisslon power display
Battery volume
display
Flight mode Model name
Timer1
11mm ' Function menu
- ' loan & Model type
display
Throttle percentage
value
System menu
lcon
Rudder trim
Throttle Dual late and Model Aileron trim
curve icon exponential menu icon
loan
1.1 Language setting
Touch the shortcut icon . to enter System Menu and then touch. to enter Language. Touch the language
that you want to select. A ‘N/ " will be shown on the screen after selected.Then touch H to save and exit.
1.1 Language setting 1.2 Display
1.2 Display
Touch the shortcut icon to enter System Menu and then touch the icons to enter “Display".
Three items are available to be set as below:
(1) Backlight brightness: the backlight brightness can be adjustable by touching the navigation marks. The
power consumption will be increased if the backlight lightness is too bright and the battery cmise duration
will be shortened.
(2) Backlight time out: it is possible to set the duration which LCD stays at highlight in the form of Always on
and duration from 5 to 60 seconds with an interval of 5 seconds.
DEVO e —4CI
oleUeniion
Welcome to use the DEVO-S transmitter DEVD a
(3) Power save time: it can adjust the backlighting duration by turning off the backlight in order to prolong
the battery cruise time. The setting status contenm Always On and duration in 30 grades with an interval
of 1 minute.
Touch H to exit.
1.3 Buzzer warning
Touch the icon to enter System Menu and then touch-to enter Buzzer interface.
(1) Buzzer switch: touch the navigation mark at Buzzer Switch
and pop up an alternative item: Off and On. It touch On.
a drop-dovm menu will be shown below.
(2) Throttle stick: under Buzzer Switch is at the status at On.
if Throttle Stick is set as “Active', a relative musical scale
will make response when moving the throttle stick. You
can judge the position of the throttle stick according to
the different musical scales. Also. it can be set as Inhibit.
(4) Buzzer tone: the tone is composed of 10 grades. You can choose the favorite tone according to your
interests. Touch Test to make a listening test.
Touch H to exit after finished.
1.4 Touch screen calibration
Touch the icon “to enter System Menu and then touch .to enter Touch Screen Calibration.
Click anywhere on the screen to start calibration with
the touch pen, and then follow the indication to calibrate.
It will automatically return to System Menu after the
calibration is finished.
1.5 Stick mode
Touch the icon
to enter System Menu, and then touch the icon. to enter Stick Mode.
There are four stick modes from MODE 1 to MODE 4. Select the stick mode you desire and then touch the
icon“ to exit.
DEVD 5 —41
o'eUenlion
Welcome to use the DEVO-S transmitter
DEvD B
1.6 Stick Calibration
Touch the icon. to enter System Menu and then touch the icon . to enter Stick Calibration. There are
two items in the interface: Stick Direction and Stick Calibration.
(1) Stick direction: there are four options: Elevator, Aileron,
Throttle, and Rudder. Click the item. which you want to
reverse. to change the output direction of the stick. The
default setting is Normal.
(2) Stick calibration: if variance happened in sticks , it would
be calibrated via this option.
Method for calibration:
Click the display item of Start to enter the status of calibration.
and Start will be turned into Stop.
(2.1) Stick calibration: Clockwise or counter clockwise mechanically move the right stick and left sticks from
their minimum levels to their maximum levels several times, and then return the sticks to the neutral positions.
respectively.
(2.2) Click the display item of Stop. If the calibration is finished, “Calibration success!" will be shown on the
lower of the screen. If the calibration is failed. “Calibration error! Please try again!" will be shown instead. It
needs to be calibrated again.
(2.3) Re-calibration: directly repeat the said steps 2.1 and 2.2 in the failure interface.
Touch the icon ii to exit.
DEvci e; 742
cJeUention
Welcome to use the DEVO-S transmitter
DEVD 5
1.7 About
Touch the icon - to enter System Menu and then
touch“ to get access to the about interface. You
can check the versions of hardware and software.
Click the icon n to exit.
2 0 Model m
Model Menu manages all the model data saved in DEVO-B. It includes Model Select, Model Name. Modei
Copy, Model Transmit. Model Receive. Model Reset, Type Select, Trim System, Device Select. Device Output.
Wing Type,Power Amplifier and Fixed ID.
2.1 Model select
Touch the icon - to enter Model Menu and then click the icon 6 to enter Model Select.
Touch the model you desire. The selected model is changed in orange color. Then click the icon “to exit.
2.1 Model name
In the menu of Model Name, you can make a desired name tor your model for long term storage. Its data
can be directly withdrawn in the next flightsRepeat the step “2.1 Model Select" to choose the model you want
to name or save. And then touch the icon n to exit.
Click the icon . to enter System Menu and then click the icon “to get the model name interface. The
following is the interface:
DEVD S —43
o'eUenlion
DEVCI a Welcome to use the DEVO-S transmitter
Click the right blank frame of Name and a gray stripe will be shown in the frame. Touch the return key
u‘ to clear up the old name.Touch the soft keyboard to input a new name. It is possible to switch
between lowercase and uppercase by clicking the key E .Then touchnto exit.
2.3 Model copy
Touch the icon .to enter Model Menu and click .to enter Model Copy.
Choose the model you want to be copied as source
model. The serial No. and model name of Source Model
will be shown in the left side of the interface.
Then touch the model in the right list where you want to
locate the source model. The serial No. and name of the
model you chose are shown under Dest Model in the
lower left of interface as well as an enquire “Are you
sure?” is popped up.
Click OK to copy. Otherwise click Cancel. Then the interface will be automatically returned to Model Menu.
Click n to save and exit.
2.4 Model wireless copy
The model data between two DEVO-S equipments can be wirelessly copied via Model Transmit and Model
Receive in Model Menu.
(1) Model transmission
Touch the icon . to enter Model Menu and then
continue to click the icon . to enter Model Transmit.
Choose the source model which will be transmitted. The serial No. and name of the source model will be
shown under Select Model in left side of the interface as well as enquiry information “Are you sure?" in the
right side.
Click OK for transmission or Cancel for rejection. Enquiry information “Transmitting ...... " appears afler
clicking OK. Touch the icon n to exit.
DEVC] 5 —44
cJeUeniion
Welcome to use the DEVO-S transmitter
DEVD 5
(2) Model receiving
Touch the shortcut icon-to enter Model Menu and then touch the icon. to enter the model receive interface.
Enquiry information “Are you sure?" is shown in the center of the interface.
Click OK for receiving or Cancel for rejection. “Connecting . . . . . ." and “Receiving .. . . . ." will be shown in
series in the interface. The information of “Received" with the model name will be shown in left side after
receiving is finished.
Choose the save position in the right name list by touching.
Enquiry information “Are you sure?“ is shown alter clicking
the save position. Click OK for save and the current interface
will automatically return to Mode Menu. Click Cancel for
rejection.
Touch the icon to exit.
2.5 Model reset
All the model data can be restored to factory settings via Model Reset.
Touch the icon .to enter Model Menu and then click . to enter Model Reset.
It is possible to store up to 12 models data in the model list of DEVO-S equipment. There are two methods
to reset the model data: batch reset and single reset.
DEVD e —45
oleUethion
DEVD E
Welcome to use the DEVO-6 transmitter
Rsssl all the models Scroll b
Reset single model
(1) Method for batch reset
Touch "All Models" in Model Reset interface. Then "All Models" and enquiry “Are you sure?" appear in the
left side. Click OK for reset, or Cancel for rejection.
(2) Method for single reset:
Touch the upper or lower navigation mark to move the scroll bar, and then choose the model you want to
restore in the model name list. The selected model‘s name and serial No, and an enquiry “It is in use! Are you
sure?“ appear in the left side. Click OK for reset, or Cancel for rejection.
Click the icon n to exit.
2.6 Type select
This device offers two model types menu. They are
helicopter and airplane.
Touch the icon -to enter Model Menu and then
click . to enter Type Select.Choose the model type
and then touch the icon B to exit.
2.7 Trim system
Trim System is able to finely tune the following four items, respectively: elevator, aileron. rudder, and throttle.
The trim range is covered from 1 to 20 grades (factory default is set at 4). It is convenient to subtly modify
the pitch by adjusting the trim range.
Touch the icon . to enter Model Menu and then click . to enter Trim System .
DEVC] 5 —46
Welcome to use the DEVO-B transmitter
oleUethion
2.8 Device select
DEVD 5
Touch the corresponding navigation mark to change the
trim value. The bigger the trim value is, the bigger the trim
range will be.
For elevator, aileron, and rudder, there are two more options:
Normal and Limited. “Normal" means the trim is always
working although the corresponding stick stays anywhere.
“Limited“ means the trim is out of working when the
corresponding stick is at maximum position.
Click the icon “to exit.
This setting can help you configure various functional switches, or adjust levers according to your flight habits.
It includes Flight Mode Switch, Flight Mode Trim ,
Setting method:
Touch the iconnlo enter Model Menu. and then
(3) Throttle Hold Switch
Throttle Hold Switch. and Flap Switch Select.
click the icon - to enter Device Select.
(1) Flight Mode Switch
Touch the navigation mark of Flight Mode Switch to expand
into a dropdown menu. Choose the mode switch you desire.
The factory default setting is Inhibit.
(2) Flight Mode Trim Select
There are two modes: Common and Flight Mode. In Common
mode all the trim values, to which various sticks are relative,
put equally ettects on all the flight modes.
In Flight Mode, the trim values to which each stick is relative
put, respectively, effect on the corresponding stick. The
factory default is Common.
Touch the navigation mark of Throttle Hold Switch to expand into a dropdown menu. Choose the mode switch
you desire. The factory default setting is DIR.
(4) Flap Select Switch
Touch the navigation mark of Flap Select Switch to expand into a dmpdown menu. Choose the mode switch
you desire. The factory default setting is MIX SW.
touch the icon n to exit.
2.9 Dcvice Output
Device output is composed of two items. It can set up output switches. It can also activate, inhibit or use
other functions.
Setting method:
Touch theqicon to enter Model Menu and then
clickcto en or Device Output.
There are two items to be adjustable .They are
GEAR,FLAP, The setting methods for them are
shown below:
DEVD 5 — 47
oleUention
DEVD a
(1) Gear
Touch the left column navigation mark of Gear and pop up an expansion including FMOD SW. MIX SW, D/R
SW, and GERA SW. Touch the desired item. The default setting is GEAR SW.
Welcome to use the DEVO-6 transmitter
Touch the right column navigation mark of Gear. Pop up an expansion including Inhibit, Active, Gyro. Touch
the desired item. The default setting is Active.
(2) Flap
There will show the switch option only after the right column at Flap is selected. Touch the right column of
Flap and expand a drepdown menu including Inhibit, Active. and System.
(2.1) If choose Inhibit or Active. the expansion menu will include these items: FMOD SW. MIX SW.D/R SW
and GEAR SW. The deiault setting is MIX SW. Select the desired item as the flap switch.
(2.2) If System is chosen, it means default setting MIX SW be choosed.
touch the icon H to exit.
2.10 Wing type
Wing Type is grouped into Flaperon, DLETA and V Tail.
Wing type selection:
Touch the ice to enter Model Menu. and then
touch a to en erthe wing type interiace.
(1) Flaperon
Touch the navigation mark of Wing Type and expand a dropdown menu with Normal. Flaperon and DELTA.
Choose the desired wing type.
DEVD rs —4El
cJeUenlion
Welcome to use the DEVO-S transmitter DEVD E
(1.1) Flaperon
Below is the graphics forthe servos location oflhe Flap and Aileron Type.
Right aileron
Connect to the outpul AILE in Receiver
Left aileron
Connect to the output Auxi in Receiver
(1.2) DELTA
Below is the graphics of the servos location of the Della Type.
Le“ Aileron Right Aileron
Connect to the outpul AILE in Receiver Connect to the output ELEV in Receiver
(2) V-TAIL
Touch the navigation mark of V-TAIL and expand a dropdown menu With Inhibit and Active. Choose Active.
Below is the graphics for the servos location of the v-tail Type.
Left empennage ighl empennage
Connect to the output ELEV in Receiver Connect to the output RUDD in Receiver
(3) Dual channels setting
Dual Channels can be set as Elevator. Aileron. Rudder. or Flaperon. It is of dual channel output function.
The channel. which Will be set as dual channel at AUX in Device Output (Refer to “2.9 Device Output"). should
be previously set as Inhibit when the AUX channel is being set.
Setting method:
(3.1) Channel setting
Touch the navigation mark of Channel in the interlace of Wing Type. and expand into Elevator. Aileron. Rudder.
and Flap. We take Elevator as an example. DEVD E_49
o'eUenlion
DEVCI a
Welcome to use the DEVO-S transmitter
(3.1) Channel setting (3.2) Mate setting
(3.2) Mate setting
Click the navigation mark of Mate and expand a dropdown menu with Inhibit. and the inhabited channel in
2.9 output device. Select the desired channel and The channel. whose characters are shown in gray, has
being applied.
(4) Twin Engine
This function can be set as twin engine output to meet
the requirement for the models, which are powered by
twin engines.
(4.1) Mate setting
Click the navigation mark of Mate and expand a dropdown
menu with Inhibit and the inhibited channels previously
set in “2.9 Device Output". Choose the desired channel
in black. These channels in gray are not available.
Click the icon “to exit after finished. (4'1) Mate setting
2.11 Power amplifier
The transmission output power of DEVO-E is adjustable. It's valid to set different wattage for different modem
is divided into six grades from small to big. The lower the transmission output power transmits, the shorter
the radio range is, and the longer the stand-by time will be.
The higher the transmission output power, the farer the
radio range. and the shorter the stand-by time. Choose the
appropriate transmission output power according to the
actual situation.
Setting method:
Touch the icon -to enter System Menu and then click
. to enter the power amplifier interface.Chgose
theappropriate output power level and then touch “ to
exit.
2.12 Fixed ID
This setting will bind DEVO-6 and its receiver in a unique corresponding relationship. It will greatly speed up
the time of automatic binding when DEVO-e powered on.
(1) Setting for fixed ID
The setting for fixed ID should be under the status that automatic ID binding is successfully finished. Below
is the setting method.
DEVC] 5 —SE|
cleUention
Welcome to use the DEVO-G transmitter DEVD 5
Touch the icon-to enter Model Menu in the main interface. and then enter Fixed ID by touching the icon
-in Model Menu.
Navigational mark
M in i Soft
keyboard
Touch the navigation mark of the item ID Code Setting. It will expand into two statuses: Off and On. A series
of random digits will be shown below after touching On.A mini soft keyboard is shown in the lower part after
touching the random digits of ID Code
The new ID digits can be modified by touching the mini sofl keyboard. Then touch Match atter the new ID is almady
set. An inquiry interface of “Are you sure?" pops up. “ID Code Match . . . . ." will be shown after touching 0K.
(2) Fixed ID cancellation
Press key"CLEAN" before the receiver is powered on, and then plug 5V DC power into one of the other output
terminals. The red light of receiver will flash slowly. This means the fixed ID code has been cancelled. Pull
out BIND PLUG.DEVO-8 also needs to make relative cancellation and revision afler the fixed ID in receiver
is cleared out.
(3) Transmitter setting
In the main interface touch the icon-to enter Model Menu
and then touch -to enter Fixed ID. ouch ID Code Setting
to expand the navigation mark into two status On and Off.
Touch Off. Then touchnto exit.
3 0 Functio M nu
Function Menu is used to make personalizedly fine adjustment to the selected models. It includes Reverse
Switch, Travel Adjust, Sub Trim, Dual Rate and Exponential, Throttle Hold, Throttle Curve, Differential setting,
Balance setting, Gyro Sensor, Aileron to Rudder Mix, Elevator to Flap Mix, Rudder to Aileronl Elevator Mix,
Flap System, Aileron to Flaperon Mix, Program Mix, Monitor, Fail Safe, Trainer, and Timer.
DEVO a —51
oleUention
DEVD e
Welcome to use the DEVO-E transmitter
3.1 Reverse switch
Touch the shortcut icon H to enter Function Menu, and then click the icona to enter the reverse switch
interface.
There show all the reverse switches‘ statuses of 6 channels.
Touch the desired item to reverse its current status. The
status includes two types: Normal and Reverse. The default
setting is Normal.
Touch the icon 5! to exit after finished.
3.2 Servo travel adjust
Touch the icon-to enter Function Menu and then click the icon.to enter the servo travel adjust interface.
The interface contents two pages to show the current travel
status of all the six channels. Touch the navigation mark
of each item to increase or decrease corresponding travel
adjustment amount. The adjustable range is 0.0% ~150.D%.
The detault setting is 100.0%.
Click the icon as to exit after finished.
3.3 Sub trim
Sub Trim is used to make parallel movement of servos. It is recommended to adjust the servo bell crank it
the servo is far away from its neutral point. The excessive usage of sub trim may damage the servo.
Setting method:
Touch the icon. to enter Function Menu and
then click the icon - to enter the sub trim
interface.
Touch the navigation mark of the desired item to
adjust the amount for rectifying the servo's neutral
point. The default neutral point is set at 0.0%.
The adjustment range of each channel is shown
as below:
Channel name Adiustment range Channel name Adjustment range
Elevator D62A5%—U62.5% R62.5%7L62.5%
R62. 5"/rL62. 5% Gear 762‘ 5"/r +62. 5%
L62 . S%7H62. 5% Flap D62. S%7U62t5%
Aileron
Throttle
Note: the model names shown will be different with the selected channels different.
Click the iconmto exit after finished.
DEvD 5—52
oleUention
Welcome to use the DEVO-G transmitter DEVD a
3.4 Dual rate and exponential
It is possible to use D/R switch to control over the dual rate of elevator, aileron, and rudder after the function
at Dual Rate and Exponential is set up. The setting range is D-125%. Under the help with exponential cunre
adjustment, it is not only manually but also automatically able to set up various parameters which are suitable
for yourself.
Setting method:
Touch the icon. to enter Function Menu and then click the icon-to enter the dual rate and exponential
interface.
(1) Channel selection
Touch the navigation mark 01 Channel and expand a
selectable list including Elevator, Aileron, and Rudder etc.
Click the desired channel which will be shown in Channel.
(2) Position selection
Touch the navigation mark of Position and expand a
selectable list including Pos 0, Pos 1. and Pos 2. Click
the desired item which will be shown in Position.
(3) Dual Rate adjustment
It is possible to modify the value by touching the navigation
mark of Dual Rate.
If touching the navigation mark forjust one item to amend
the dual rate value, the dual rate of the corresponding
servo will be changed in one direction. while the curve
will being changed in one direction at the right graph. ‘ '
(4) Exponential adjustment
It is possible to adjust the exponential output value of the servo at that point. which is set up in step “(2) Position
selection", by touching the navigation mark oi Exponential.
If touching the navigation mark forjust one item to amend the dual rate value, the dual rate of the corresponding
servo will be changed in one direction, while the curve will being changed in one direction at the right graph
(5) Automatic setting
Under working with Flight Mode. it is possible to switch between the dual rate and exponentiaI.The settings
for Flight Mode 0, Flight Mode 1, and Flight Mode 2 are available.
Note: Before using the function of automatic setting, the Flight Mode Switch should be previously set as relative
switches. Reierto “2.8 Device Select".
—1r
Touch the flight mode that you want to set as automatic
operation, and an expansion list will be shown. Click the
desired position. If Switch is selected, it is only controlled
by the corresponding dual role lever.
Click the icon H to exit.
DEVD s —53
oleUention
DEVD 6 Welcome to use the DEVO-G transmitter
3.5 Throttle hold
If this function is set. the switch will be executed by hold switch. The setting value of throttle hold is ranged
from -20.0% to 50.0%.Factory default setting is inhibit.
Setting method:
Touch the shortcut icon'to enter Function Menu, and then click-to enter the throttle hold interface.
Touch the navigation mark of Hold Status, and an expansion list will be shown as Inhibit and Active. Click
Active, there appear Switch, and Hold Position in the above interface.
(1) Setting for Switch
This item can be set under the THROTTLE HOLD SW of MODEL MENU / Device select. Refer to (2.8 Device
Select). The default setting is HOLD SW.
(2) Setting for Hold Position
Touch the left navigation mark of the item Hold Position to decrease the position amount, whose minimum
is -20.0%: touch the right to increase the position amount whose maximum is *50.0%.
When toggle the HOLD DIR switch forward, it means on via backward means off. Throttle hold status will be
unlocked.
Click the icon fito exit after all the settings are finished.
3.6 Throttle curve
Throttle curves are adjusted through seven points, which of all the flight modes can be respectively set.
Setting method:
Touch the icon - to enter Function Menu and then click the icon to enter the throttle curve interface. A
dropdown menu with “All Servos Hold?" pops up.CIick OK for all the servos locked at the current statuses.
Click Cancel for all the servos unlocked.
cleUeniion
Welcome to use the DEVO-6 transmitter
DEVD £5
(1) Channel setting
Afler previously set up Twin Engine, touch the navigation
mark of Channel and expand a list including Left Throttle
and Right Throttle. Select the desired throttle which will be
shown in Channel. Channel will be shown in grey il Twin
Engine is not previously selected.
(2) Position selection
Touch the navigation mark of Position and expand a list with
Pos 0 and Pos 1. select the item you want to set.
(3) Exponential setting (1) Channel setting
Touch the navigation mark of Exponential and expand a list with of! and On. The throttle curve will being
changed smoothly if clicking On.
(4) Point setting
Touch the navigation mark oi Point and expand a list
including seven points. Select the point you want to adjust.
(5) Status setting
Touch the navigation mark of Status and expand a list with
Inhibit and Active. Click Inhibit tor keeping the current value
(the detault setting is Inhibit); click Active for changing the
above point's value. Another item Output will be shown
below after choosing Active.
(4) Point setting
(5) Output setting
Touch the left or right navigation mark of Output to decrease or increase, respectively, the output value. The
adjustable range is trom 0.0% to 100.0%.
(7) Throttle setting
Touch the Iett or right navigation mark of Throttle Stick to decrease or increase, respectively. the amount
with a lower limit of 0.0% and an upper limit of 100.0%. The default setting is Inhibit.
The switch between Pos 1 and Pos 0 can be freely realized through throttle stick otter the above amount
has been set up.The above set amount is the position of throttle stick as well as the switch point.
(8) Switch selection
When the item Throttle Stick is set in Inhibit. it is possible to switch between Pos 0 and Pos 1 by Switch.
Touch the navigation mark of Switch and expand a
dropdown menu including the selectable items in black.
Select the desired item whose left side will be changed
into “1"trom “0". If two items are selected, the item And
should be chosen. Then touch the navigation mark of
Switch to retum back.
Click the iconfito exit after linished.
3.7 Differential
ll want to use this function, Flaperon, DELTA should be previously selected in Wing Type of Model Menu.
Refer to “2.12 Wing Type".
DEVD 5— 55
AeUenLon Welcome to use the DEVO-6 transmitter
DEVD a
(1) Aileron differential setting:
Touch the shortcut icor'to enter Function Menu. and then click the icon - to enterthe interface of Differential.
Mounting servos in left and right ailerons are a must if using this function. The following interface will be shown
after Flaperon, DELTA selected in Wing Type. Refer to “2.10 Wing Type”.
(1.1) Setting for Pos 0
Touch the left or right navigation mark of Pos 0 to
decrease or increase, respectively, differential value.
The bigger the value is, the bigger the differential is.
The adjustable range is t 100%.
(1.2) Setting for Pos 1
The setting is same as above.
(1.3) Switch selection
It is possible to switch by setting switch when differential
is in use.
Touch the navigation mark of Switch and expand a
selectable list. Click the switch item, which you desire, to
change “D“ into “1“. Iftwo or more switch items are selected,
the item And should be chosen. Then click the navigation
mark to return.CIick the iconnto exit after finished.
(2) Rudder differential setting
V-Tail should be previously set in Wing Type of Model Menu if the rudder differential function is activated.
Refer to ‘2.10 Wing Type". And then the following interface will be shown:
(2.1) Setting for Pos 0
Touch the left or right navigation mark of Pos 0 to decrease
or increase. respectively, differential value. The bigger the
value is. the bigger the differential is. The adjustable range
is 1 100%.
(2.2) Setting for Pos 1
The setting is same as above.
(2.3) Switch selection
It is possible to switch by setting switch when differential
is in use.
Touch the navigation mark of Switch and expand a
selectable list. Click the switch item, which you desire, to
change “0“ into “1“. If two or more switch items are selected.
And should be chosen. Then click the navigation mark to
reiurn.Click the icon “to exit after finished.
(3) Flap differential setting
It should be previously set the flap dual channel function in Device Output at Model Menu (refer to "2.10 Wing
Type") in order to activate the menu of Flap Differential.
DEVC] 5 —56
deUenlion
Welcome to use the DEVO-s transmitter DEVD a
(3.1) Setting tor Pos 0
Touch the left or right navigation mark of Pos 0 to decrease
or increase, respectively, differential value. The bigger
the value is. the bigger the differential is. The adjustable
range is 1 100%.
(3.2) Setting for Pos 1
The setting is same as above.
(3.3) Switch selection
It is possible to switch by setting switch when differential
is in use.
Touch the navigation mark of Switch and expand a
selectable list. Click the switch item, which you desire.
to change “0" into “1". If two or more switch items are
selected, And should be chosen. Then click the navigation
mark to return.CIick the icon n to exit after finished.
3.6 Balance
This function can adjust the parameters of the two servos which are used in the dual channels. It should be
previously chosen one of the these wing types of Flaperon, DELTA, and V Tail in Wing Type at Model Menu.
Refer to “2.10 Wing Type".
Setting method:
Touch the icon ”to enter Function Menu, and then click the icon fito enter the balance interface.
(1) Channel selection
Touch the navigation mark of Channel and expand a selectable list. Choose the desired channel.
(2) Point parameter adjustment
Touch the navigation mark of Point that you want to select,
and pops up a dropdown menu including Inhibit and Active.
Click Active for adjusting the value by touching the left or
right navigation mark. 0% means no adjusting. A minus value
means the amending direction is downward, and a plus value
means the amending direction is upwardAdjusting range is
$1007:
Click the icon “to exit after finished.
DEVD rs — 57

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Mode                       : UseNone
XMP Toolkit                     : 3.1-702
Create Date                     : 2011:10:14 10:41:25+08:00
Creator Tool                    : S29DEVO-6_user manual.pdf
Modify Date                     : 2011:10:14 10:47:54+08:00
Metadata Date                   : 2011:10:14 10:47:54+08:00
Format                          : application/pdf
Creator                         : Frank
Title                           : S29DEVO-6_user manual.pdf
Producer                        : ScanSoft PDF Create! 5
Document ID                     : uuid:9a7668e9-3402-4dd7-a06c-f09759c51a51
Instance ID                     : uuid:0e0edee6-3bd7-425d-9ce1-3feb546ed518
Page Count                      : 20
Author                          : Frank

EXIF Metadata provided by EXIF.tools