Guangzhou Chiyuan Electronic N-8C Radio Control System User Manual N 8C Introduction Manual
Guangzhou Chiyuan Electronic Co., Ltd. Radio Control System N 8C Introduction Manual
Users Manual
Thank you for purchasing our‘ ’R/C system.
Before using, read this manual carefully.
T P C A R EOT P C A R EO
8 Channel PPM/FM Radio Control System
Introduction Manual
N-8C R/C
RADIO CONTROL SYSTEM
CCPM
T P C A R EOT P C A R EO
Guangzhou Chiyuan Electronic Co., Ltd
Add: 2/F., No. 1 Bldg., Boyi Industrial Garden, 4th Gongye Rd.
Zhicun, Dashi Street, Panyu Dis., Guangzhou, China
P.C.: 511430
Tel: +86-20-34796226;34797226
Fax: +86-20-34796116
Website: www.chiyuan.net
E-mail: gzchiyuan@126.com
R/C Introduction Manual R/C Introduction Manual
Caution ....................................................................................................
1.1 N-8C Transmitter Chart .....................................................................
2.3 D/R & EXP ........................................................................................
2.4 Rev. SW .............................................................................................
2.5 Sub Trim ............................................................................................
2.6 Trvl ADJ. ...........................................................................................
2.7 Swash TYP..........................................................................................
2.8 Swash Mix .........................................................................................
2.9 Stick Mode ........................................................................................
2.10 Thro Curv ........................................................................................
2.11 Pit Curv ............................................................................................
2.12 Planes ...............................................................................................
2.13 Clear .................................................................................................
2.14 Gyro Sens ........................................................................................
2.15 Idel Thro ..........................................................................................
2.16 Idel Pith ...........................................................................................
2.17 Plane Type .......................................................................................
3.1 Upright Operation of Left Stick and Movement of Elevator ..........
3.2 Level Operation of Left Stick and Movement of Rudder ...............
3.3 Upright Operation of Right Stick and Movement of Throttle .........
3.4 Level Operation of Right Stick and Movement of Aileron .............
4.1 Back of Transmitter .........................................................................
4. 2 Trainer Function ..............................................................................
5.1 Control Stick Length&Tension Adjustment ....................................
5.2 Loading Batteries ............................................................................
2.1 Menu ..................................................................................................
2.2 Function List ......................................................................................
6.1 Three-servo Connection Diagram ...................................................
6.2 Two-servo Connection Diagram ......................................................
6.3 Four-servo Connection Diagram .....................................................
6.4 ACRO Connection Diagram ............................................................
6.5 V-tail Mixing Connection ................................................................
6.1 Three-servo Connection Diagram ...................................................
6.2 Two-servo Connection Diagram ......................................................
6.3 Four-servo Connection Diagram .....................................................
6.4 ACRO Connection Diagram ............................................................
6.5 V-tail Mixing Connection ................................................................
1
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
12
13
13
14
15
15
16
17
18
19
20
21
22
Table of Contents
R/C Introduction Manual
1
! To work your R/C with your models correctly and safely, read this manual
carefully and keep it in a safe way as a reference introduction in the future.
! Warning:
1. This product is only equipped for radio controlled models;
2. The usage of this product should be approved by local relevant law or
regulations;
3. We will be not responsible for the damages caused by unauthorized
modification,adjustment or replacement of parts of this product;
4. The manual may be altered without prior notice. Please contact us if you have
any corrections or clarifications that should be made in the manual.
! Please pay more attention on the parts in this manual, which marked with
“warning”.
! Because of disturbance, do not work your radio control system simultaneously
with others at the same frequency.
! Before starting the transmitter, make sure the transmitter batteries are well loaded
.The voltage of transmitter batteries never be lower than 8.6V. And please check
and confirm that the servos are all well and properly connected.
! Please take off batteries from transmitter after flying and during the
transportation.
! Please check and have a test on control surfaces to confirm the transmitter
handling of each part prior to each takeoff. The frequencies of the module and
the receiver should be the same.
! The instructor and the student transmitters must accord with each other when
using trainer function.
! Keep the radio system away from moist, high temperature and strong shake. Do
not clean the product with solvent.
! Do not fly your models near airfield, schools, hospitals, residences, power
transmission network, communication facilities and other places that are
forbidden for starting the transmitter. Please stop flying your models with the
radio on rainy or windy days, or at night.
! Do not fly the models when you are tired, sick , intoxicated,or not in good spirit.
! The antenna do not touch anything else when power switch is turned on. Do not
leave this product and its accessories within the reach of small children.
! Please use this product according to your local relevant law or regulation,we are
not responsible for any incidents or damages.
! Important Comments: All USB ports in this transmitter are just used for our
special cord with its USB structure and without USB agreement. DO NOT USE
your USB cables with transmitter.
Caution
R/C Introduction Manual 2
1.1 N-8c功能示意图
1.1 N-8C Transmitter Chart
!Press “OK/Return” to entry the main menu. (“OK/Return” here in after refered to as“ ”)
!Press “Up ” and “Down ” for selecting functions in the list; press“ ” to enter the
selected function; press “ ”to return to the previous menu.(“Up ” here in after refered to
as“ ”;“Down ” here in after refered to as“ ”)
!Press “Increase ”and “Decrease ”to change input data.(“Increase ” here in after refered to
as“ ”;“Decrease” here in after refered to as“ ”)
Goyr. Sens.
Adj. SW
Antenna
Trainer SW
Power SW
Eyelet
Handle
Idel. SW
Elev. D/R SW
Pit Adj. SW
Left Stick
LCD
Aile. D/R SW
Thro.Hold SW
Right Stick
Input Keys
Charging Jack
Up
Down
Decrease
Increase
Ok/Return
R/C Introduction Manual R/C Introduction Manual 43
2.3 D/R & EXP
!Function
Dual rates are available for elevator and rudder channels of RC helicopters.
!Operation
1. Press “ ” to entry the menu – Roll“ ” or “ ”select the function (D/R & Exp) in
the list Press “ ” to set the function and return to the previous menu.
2. Roll “ ” or “ ” to select ELEV and AILE to set the data.
3. ELEV setting ---- ‘ELEV’ is displayed
Once the Elevator D/R switch is on/up, the data displayed is ‘Pos 0’. Use “ ” or “ ”
to increase or decrease the data.(2.3.1)
Once the Elevator D/R switch is off/down, the data displayed is ‘Pos 1’. Use “ ” or “ ”
to increase or decrease the data.(2.3.2)
4. AILE setting ---- ‘AILE” is displayed
Once the Aileron D/R switch is on/up, the data displayed is ‘Pos 0’. Use “ ” or “ ” to
increase or decrease the data. (2.3.3)
Once the Aileron D/R switch is off/down, the data displayed is ‘Pos 1’. Use “ ” or “ ”
to increase or decrease the data. (2.3.4)
5.Press “ ” to save and return to the previous menu.
[D/R&EXP][D/R&EXP]
AILEAILE
Pos0Pos0
79%79%
D/R
LIN
D/R
LIN
[D/R&EXP][D/R&EXP]
AILEAILE
Pos1Pos1
42%42%
D/R
LIN
D/R
LIN
[D/R&EXP][D/R&EXP]
ELEVELEV
Pos0Pos0
79%79%
D/R
LIN
D/R
LIN
[D/R&EXP][D/R&EXP]
ELEVELEV
Pos1Pos1
42%42%
D/R
LIN
D/R
LIN
(2.3.1)(2.3.1) (2.3.2)(2.3.2) (2.3.3)(2.3.3) (2.3.4)(2.3.4)
2.4 Rev. SW
CH 1 2 3 4 5 6 7 8CH 1 2 3 4 5 6 7 8
RR
NN
[REV.SW][REV.SW]
THRO THRO
CH 1 2 3 4 5 6 7 8CH 1 2 3 4 5 6 7 8
RR
NN
[REV.SW][REV.SW]
AUX3 AUX3
CH 1 2 3 4 5 6 7 8CH 1 2 3 4 5 6 7 8
RR
NN
[REV.SW][REV.SW]
ELEV ELEV
! Function
The Reverse switch is to change the servo for channel direction.
! Operation
1.Select ‘REV. SW’ and entry the interface.
2.Use “ ” or “ ” to select the channel arrow position. Press “ ” to reverse the
channel; press “ ” to the normal status.
3.Press“ ” to save and return to the previous menu.
2.2 Function List
"[FUNC.LIST]"
" D/R & EXP" Dual Rate
" Rev. SW"
" Sub Trim" Sub Trim
" Trvl ADJ." Travel Adjustment
" Swash Mix" Swash Mixing
" Swash TYP" Swash Type
" Stick Mode" Stick Mode
" Thro Curv" Throttle Curve
" Pit Curv" PIT. Curve
" Planes" Planes
" Clear" Clear
" Gyro Sens" Gyro Sensitivity
" Idel Thro" Idle Throttle
" Idel Pith" Idle Pitch
"PLANE TYPE" PLANE TYPE
" Exit"
2.1 Menu
!It is a default setting of helicopter in Model Type initially.
!When the voltage displayed is 8.6V below, the number will be flashed and simultaneously
with warning.
U:U:
11.5v11.5v
8 Channel R/C8 Channel R/C
PPM/FMPPM/FM
Channel TypeChannel Type
Model Type
VoltageVoltage
Modulation TypeModulation Type
Reversing SwitchReversing Switch
T P C A R EOT P C A R EO
Exit
[SWASH TYP][SWASH TYP]
2Servos
2Servos
180180..
CCPMCCPM
[SWASH TYP][SWASH TYP]
3Servos
3Servos
120120..
CCPMCCPM
[SWASH TYP][SWASH TYP]
4Servos
4Servos
9090..
CCPMCCPM
[SWASH TYP][SWASH TYP]
CP MOD
CP MOD
[SWASH Mix][SWASH Mix]
4Servos
4Servos
EL +50% EL +50%
PI +50% PI +50%
AI +50% AI +50%
9090..
[SWASH MIX][SWASH MIX]
3Servos
3Servos
EL +50% EL +50%
PI +50% PI +50%
AI +50% AI +50%
120120..
[SWASH MIX][SWASH MIX]
2Servos
2Servos
PI +50%
EL +50%
PI +50%
EL +50%
AI +50% AI +50%
180180..
[SWASH MIX][SWASH MIX]
Ser osSer os
On1 oneOn1 one
R/C Introduction Manual R/C Introduction Manual 65
2.8 Swash Mix
!Function
This function is to set the swash mixing data.
!Operation
1.Select ‘SWASH MIX’ and entry the interface.
2.Use “ ” or “ ” to select the channel arrow position. Press “ ” or “ ” to set the
mixing data between the Travel value and the Throttle.
3.Press “ ” to save and return to the previous menu.
Notes: Please set the ‘Swash TYP’ before entering the Swash Mix.(cp mode;2Servos;
3Servos;4Servos;)
2.7 Swash TYP
!Function
This function is to select a Swash type.
!Operation
1.Select ‘SWASH TYP’ and entry the interface.
2.Use “ ” or “ ” to select the mode: CP mode/2Servos/3Servos/4Servos.
3.Press “ ” to save and return to the previous menu.
SWASH TYP
2.6 Trvl ADJ.
2.5 Sub Trim
[Sub.Trim ][Sub.Trim ]
THRO
-13%
THRO
-13%
ELEV
-19%
ELEV
-19%
AILE
-20%
AILE
-20%
RUDD
+10%
RUDD
+10%
[Sub.Trim ][Sub.Trim ]
GEAR
-18%
GEAR
-18%
FLAP
+ 8%
FLAP
+ 8%
PITH
- 3%
PITH
- 3%
AUX3
+10%
AUX3
+10%
! Function
The Sub trim is a trim position setting on 8 channels.
! Operation
1.Select ‘Sub Trim’ and entry the interface.
2.Use “ ” or “ ” to select the channel arrow position. Press “ ” or “ ” to change
the data.(2.5.1)
3.Use “ ” or “ ”to display circularly the other channels below. Press “ ” or
“ ” to change the data. (2.5.2)
4.Press “ ” to save and return to the previous menu.
(2.5.1)(2.5.1) (2.5.2)(2.5.2)
[TRVL ADJ.][TRVL ADJ.]
THRO
-13%
THRO
-13%
ELEV
-19%
ELEV
-19%
AILE
-20%
AILE
-20%
RUDD
+10%
RUDD
+10%
[TRVL ADJ.][TRVL ADJ.]
GEAR
-18%
GEAR
-18%
FLAP
+ 8%
FLAP
+ 8%
PITH
- 3%
PITH
- 3%
AUX3
+10%
AUX3
+10%
! Function
The function is an electronic means to adjust the servo travel value.
! Operation
1.Select ‘TRVL ADJ.’ and entry the interface.
2.Use “ ” or “ ” to select the channel arrow position. Press “ ” or “ ” to change
the data.(2.6.1)
3.Use “ ” or “ ”to display circularly the other channels below. Press “ ” or
“ ” to change the data. (2.6.2)
4.Press “ ” to save and return to the previous menu.
(2.6.1)(2.6.1) (2.6.2)(2.6.2)
[Planes][Planes] BB
AA
CCDD
EEFF
BB
R/C Introduction Manual R/C Introduction Manual 87
2.11 Pit Curv
! Function
This radio offers 2 separate pitch curves with 5 adjustable points per curve: L/1/2/3/H.
! Operation
1.Select ‘PIT. CURV’ and entry the interface.
2.Use “ ” or “ ” to select any point at arrow that is in need to reset the data. Press “
” or “ ” to set the data separately as the curve is being changed accordingly.
3.Press “ ” to save and return to the previous menu.
PIT. CURV
2.12 Planes
! Function
This radio has a memory for 6 models with their data individually.
! Operation
1.Select ‘PlANES’ and entry the interface.
2.Use “ ” or “ ” to select the model memorized with a code.
3..Press “ ” to save and return to the previous menu.
[Planes][Planes] FF
AA
CCDD
EEFF
BB
[Planes][Planes] AA
AA
CCDD
EEFF
BB
[PIT. CURV][PIT. CURV]
1:1:
2525
[PIT. CURV][PIT. CURV]
L:L:
00
[PIT. CURV][PIT. CURV]
H:H:
100100
2.9 Stick Mode
[STICK MODE][STICK MODE]
RIGHT STICK RIGHT STICK
MODE 1 MODE 1
[STICK MODE][STICK MODE]
LEFT STICK LEFT STICK
MODE 2 MODE 2
! Function
This function allows you to exchange mode 1 and mode 2.
! Operation
1.Select ‘STICK MODE’ and entry the interface.
2.Use “ ” or “ ” to select the mode.
3.Press “ ” to save and return to the previous menu.
Notes: To change the mode, it is necessary to remove the model of the transmitter.
2.10 Thro Curv
! Function
This radio offers 2 separate throttle curves with 5 adjustable points per curve: L/1/2/3/H.
! Operation
1.Select ‘THRO CURV’ and entry the interface.
2.Use “ ” or “ ” to select any point at arrow that is in need to reset the data. Press “
” or “ ” to set the data separately as the curve is being changed accordingly.
3.Press “ ” to save and return to the previous menu.
[THRO CURV][THRO CURV]
1:1:
2525
[THRO CURV][THRO CURV]
L:L:
00
[THRO CURV][THRO CURV]
H:H:
100100
R/C Introduction Manual R/C Introduction Manual 109
2.15 Idel Thro
! Function
This function is a possibility to adjust the pitch curve with 5 points in 3D mode.
! Operation
1.Select ‘IDEL PITH’ and entry the interface.
2.Use “ ” or “ ” to select any point at arrow that is in need to reset the data. Press “
” or “ ” to set the data separately as the curve is being changed accordingly.
3.Press “ ” to save and return to the previous menu.
This function is a possibility to adjust the pitch curve with 5 points in 3D mode.
IDEL PITH
! Function
This function is a possibility to adjust the throttle curve with 5 points in 3D mode.
! Operation
1.Select ‘IDEL THRO’ and entry the interface.
2.Use “ ” or “ ” to select any point at arrow that is in need to reset the data. Press “
” or “ ” to set the data separately as the curve is being changed accordingly.
3.Press “ ” to save and return to the previous menu.
This function is a possibility to adjust the throttle curve with 5 points in 3D mode.
IDEL THRO
2.16 Idel PithIdel Pith
[IDEL THRO][IDEL THRO]
1:1:
2525
[IDEL THRO][IDEL THRO]
L:L:
00
[IDEL THRO][IDEL THRO]
H:H:
100100
[IDEL PITH][ID EL PITH]
1:1:
2525
[IDEL PITH][ID EL PITH]
L:L:
00
[IDEL PITH][ID EL PITH]
H:H:
100100
[Clear][Clear]
Reset or no?Reset or no?
[N][N]
[Y][Y]
2.13 Clear
[Clear][Clear]
Reset or no?Reset or no?
[N][N]
[Y][Y]
! Function
This function helps with returning the factory preset.
! Operation
1.Select ‘CLEAR’ and entry the interface.
[Y] and [N] are displayed.
[Y] is to return the factory preset;(2.13.1)
[N] is not to return the factory preset. (2.13.2)
2.Use “ ” or “ ” to select the answer.
3.Press “ ” to save and return to the previous menu.
(2.13.1)(2.13.1) (2.13.2)(2.13.2)
2.14 Gyro Sens
[GYRO SENS][GYRO SENS]
Pos0Pos0
Pos1Pos1 80%80%
20%20%
[GYRO SENS][GYRO SENS]
Pos0Pos0
Pos1Pos1 80%80%
20%20%
! Function
This function offers a gyro adjustment with 2 points.
! Operation
1.Select ‘GYRO SENS’ and entry the interface.
2.Once ‘the Gyro Sensitivity Adjustment SW’ is off/down, the data displayed is ‘Pos 0’.
Use “ ” or “ ” to adjust the data.
Once ‘the Gyro Sensitivity Adjustment SW’ is on/up, the data displayed is ‘Pos 1’. Use “
” or “ ” to adjust the data.
3.Press “ ” to save and return to the previous menu.
(2.14.1)(2.14.1) (2.14.2)(2.14.2)
R/C Introduction Manual R/C Introduction Manual 1211
BBBB
Elevator
L Stick
Upwards
Plane
M
O
ModeⅠ
L Stick
Downwards U
D
U
D
Elevator
3.1 Upright Operation of Left Stick and Movement of Elevator
3. Transmitter Operation and Movement (for Airplane)
This chapter will introduce transmitter’s stick operation and movement of each servo
of aeroplane, including stick operation and movements of Elevator, Rudder, Throttle,
Aileron. (Mode 1)
Left Stick Vertaical Operation
2.17 PLANE TYPE
[SWASH TYP][SWASH TYP]
CP MOD
CP MOD
[]PLANE TYPE[]
Airplane
Airplane
V-Tail Mix
V-Tail Mix
3D Mix
3D Mix
[]PLANE TYPE[]
Airplane
Airplane
V-Tail Mix
V-Tail Mix
3D Mix
3D Mix
[]PLANE TYPE[]
Airplane
Airplane
V-Tail Mix
V-Tail Mix
3D Mix
3D Mix
! Function
This function is loaded with airplane and helicopter programming.
! Operation
1.Select “SWASH TYP” and entry the interface of "CP MOD”.
2.Entry “PLANE TYPE”.
3.Use “ ” or “ ” to select the model type.
4..Press “ ” to save and return to the previous menu.
! Swash Adjustment
1. Turn on the transmitter. Press Select keys to enter the Swash Type and select swash
type you want.
2. Open the horns of swash plate servos.
3. Move the throttle stick(engine turned on) to observe the circumvolving direction of the
servos horn. By reverse, you can adjust the direction.
4. Press Select keys to enter the Sub Trim and return all values to zero.
5. Lock the servos' horns.
6. Observe the circumvolving direction of the swash plate by moving aileron and elevator.
Change it by adjusting the value of aileron and elevator in Swash Mix list.
7. Gyro Adjustment------Press Select keys to enter the Gyro Sensor and adjust the value you
want by O/I switch.
8. Finished all of the above, you can fly your helicopter freely.
R/C Introduction Manual R/C Introduction Manual 1413
M
O
ModeⅠ
Motor
Plane
Decelerating
Decelerating
Accelerating
Accelerating
R Stick
Downwards
R Stick
Upwards
Rudder
L Stick
Rightwards
L Stick
Leftwards
Plane
M
O
Left Stick Horizontal Operation
ModeⅠ
R
R
L
L
3.3 Upright Operation of Right Stick and Movement of Throttle
Right Stick Vertaical Operation
Rudder
3.2 Level Operation of Left Stick and Movement of Rudder
3.4 Level Operation of Right Stick and Movement of Aileron
Ri gh t St ic k Ho ri zo nt al O pe ra ti on
R Stick
Rightwards
R Stick
Leftwards
(Mod eⅠ)
M
O
Left
Aileron
Right
Aileron Plane
D
U
D
R
U
L
R Aileron
L Aileron
R/C Introduction Manual R/C Introduction Manual 1615
4.1 Back of Transmitter
Module
Trainer
Battery Cover
! Connect the student and the instructor transmitters with the trainer cord. Confirm
the connection is OK.
! The instructor transmitter is used as a normal setting; Turn down the student
transmitter and take off its Replaceable Module and batteries. (Do not extend
the antenna of student transmitter)
! When the trainer switch of the instructor is pushed, like the following
illustration, the model can be controlled by student. When the trainer switch of
instructor returns, the model is under instructor's control.
! The training function is only active with T-1 trainer cord.
4. 2 Trainer Function
High Cap
Low Cap
! For your convenient operation, the stick length
can be adjusted as your demand.
! Screw the high cap anticlockwise to the desired
length and then, screw the low cap anticlockwise
to lock the high cap as the left illustration.
! For your convenient operation, the stick tension
can be adjusted as your demand.
! Use the screwdriver to adjust the screw clockwise
for the desired tension. anticlockwise to loosen
stick feel, clockwise to tighten stick feel.
! This adjustment need take off the back cover of
transmitter.
This chapter will introduce the installation and adjustment of some important parts of
transmitter, including Control Stick Length and Tension Adjustment, Loading
Batteries, Loading Module and Connection between Receiver and Servos.
5.1 Control Stick Length&Tension Adjustment
5. Installation and Adjustment
R/C Introduction Manual 18
6.1 Three-servo Connection Diagram6.1 Three-servo Connection Diagram
B
Ch8
CH7
CH6
CH5
CH4
CH3
CH2
CH1
B
Ch8
CH7
CH6
CH5
CH4
CH3
CH2
CH1
GyroGyro
Servo 4Servo 4 Servo 3Servo 3
Servo 2Servo 2
Servo 1Servo 1
AILE.AILE.
PITCHPITCH
ELEV.ELEV.
RUDD.RUDD.
MotorMotor
Electronic
Speed
Controller
Electronic
Speed
Controller
PowerPower
ReceiverReceiver
(AILE.)(AILE.)
(ELEV.)(ELEV.)
(PITCH)(PITCH)
FrontFront
R/C Introduction Manual
17
图 4.3.1
! Open the battery cover in the direction of the arrow while pressing the non-slip
cover grips.
! Load the batteries in accordance with the battery holder polarity marking and
close the battery cover.(5.2.1)
5.2.1
5.2 Loading Batteries
R/C Introduction Manual R/C Introduction Manual 2019
B
Ch8
CH7
CH6
CH5
CH4
CH3
CH2
CH1
B
Ch8
CH7
CH6
CH5
CH4
CH3
CH2
CH1
GyroGyro
Servo 3Servo 3
Servo 2Servo 2
Servo 1Servo 1
AILE.AILE.
ELEV.ELEV.
RUDD.RUDD.
MotorMotor
Electronic
Speed
Controller
Electronic
Speed
Controller
PowerPower
6.2 Two-servo Connection Diagram6.2 Two-servo Connection Diagram
ReceiverReceiver
(AILE.)(AILE.)
(ELEV.)(ELEV.)
FrontFront
6.3 Four-servo Connection Diagram6.3 Four-servo Connection Diagram
B
Ch8
CH7
CH6
CH5
CH4
CH3
CH2
CH1
B
Ch8
CH7
CH6
CH5
CH4
CH3
CH2
CH1
GyroGyro
Servo 4Servo 4 Servo 3Servo 3
Servo 2Servo 2
Servo 1Servo 1
AILE.AILE.
PITCHPITCH
ELEV.ELEV.
RUDD.RUDD.
MotorMotor
Electronic
Speed
Controller
Electronic
Speed
Controller
PowerPower
ReceiverReceiver
Servo 5Servo 5
AUX3AUX3
(AUX3)
(AUX3)
(AILE.)(AILE.)
(ELEV.)(ELEV.)
(PITCH)(PITCH)
FrontFront
R/C Introduction Manual R/C Introduction Manual 2221
B
Ch8
CH7
CH6
CH5
CH4
CH3
CH2
CH1
B
Ch8
CH7
CH6
CH5
CH4
CH3
CH2
CH1
Servo 4Servo 4
Servo 2Servo 2
Servo 1Servo 1
MotorMotor
Electronic
Speed
Controller
Electronic
Speed
Controller
PowerPower
6.4 ACRO Connection Diagram6.4 ACRO Connection Diagram
ReceiverReceiver
Servo 3Servo 3
Ch2
Ch6
Ch4
Ch3
Ch2
Ch6
6.5 V-tail Mixing Connection 6.5 V-tail Mixing Connection
B
Ch8
CH7
CH6
CH5
CH4
CH3
CH2
CH1
B
Ch8
CH7
CH6
CH5
CH4
CH3
CH2
CH1
Servo 2Servo 2
Servo 1Servo 1
MotorMotor
Electronic
Speed
Controller
Electronic
Speed
Controller
PowerPower
ReceiverReceiver