Guangzhou Chiyuan Electronic N-8C Radio Control System User Manual N 8C Introduction Manual

Guangzhou Chiyuan Electronic Co., Ltd. Radio Control System N 8C Introduction Manual

Users Manual

Thank you for purchasing our‘ ’R/C system. Before using, read this manual carefully.T P C A R EOT P C A R EO8 Channel PPM/FM Radio Control System Introduction Manual N-8C R/CRADIO CONTROL SYSTEMCCPMT P C A R EOT P C A R EOGuangzhou Chiyuan Electronic Co., LtdAdd: 2/F., No. 1 Bldg., Boyi Industrial Garden, 4th Gongye Rd. Zhicun, Dashi Street, Panyu Dis., Guangzhou, ChinaP.C.: 511430Tel: +86-20-34796226;34797226 Fax: +86-20-34796116Website: www.chiyuan.netE-mail: gzchiyuan@126.com
R/C Introduction Manual R/C Introduction ManualCaution .................................................................................................... 1.1 N-8C Transmitter Chart ..................................................................... 2.3 D/R & EXP ........................................................................................ 2.4 Rev. SW ............................................................................................. 2.5 Sub Trim ............................................................................................ 2.6 Trvl ADJ. ...........................................................................................2.7 Swash TYP..........................................................................................2.8 Swash Mix ......................................................................................... 2.9 Stick Mode ........................................................................................2.10 Thro Curv ........................................................................................2.11 Pit Curv ............................................................................................2.12 Planes ...............................................................................................2.13 Clear .................................................................................................2.14 Gyro Sens ........................................................................................2.15 Idel Thro ..........................................................................................2.16 Idel Pith ...........................................................................................2.17 Plane Type .......................................................................................3.1 Upright Operation of Left Stick and Movement of Elevator ..........3.2 Level Operation of Left Stick and Movement of Rudder ...............3.3 Upright Operation of Right Stick and Movement of Throttle .........3.4 Level Operation of Right Stick and Movement of Aileron .............4.1 Back of Transmitter .........................................................................4. 2 Trainer Function ..............................................................................5.1 Control Stick Length&Tension Adjustment ....................................5.2 Loading Batteries ............................................................................2.1 Menu ..................................................................................................2.2 Function List ......................................................................................6.1 Three-servo Connection Diagram ...................................................6.2 Two-servo Connection Diagram ......................................................6.3 Four-servo Connection Diagram .....................................................6.4 ACRO Connection Diagram ............................................................6.5 V-tail Mixing Connection ................................................................6.1 Three-servo Connection Diagram ...................................................6.2 Two-servo Connection Diagram ......................................................6.3 Four-servo Connection Diagram .....................................................6.4 ACRO Connection Diagram ............................................................6.5 V-tail Mixing Connection ................................................................123344556677889910101112131314151516171819202122Table of Contents
R/C Introduction Manual1! To work your R/C with your models correctly and safely, read this manual carefully and keep it in a safe way as a reference introduction in the future. ! Warning: 1. This product is only equipped for radio controlled models; 2. The usage of this product should be approved by local relevant law or regulations; 3. We will be not responsible for the damages caused by unauthorized modification,adjustment or replacement of parts of this product; 4. The manual may be altered without prior notice. Please contact us if you have any corrections or clarifications that should be made in the manual.! Please pay more attention on the parts in this manual, which marked with “warning”. ! Because of disturbance, do not work your radio control system simultaneously with others at the same frequency. ! Before starting the transmitter, make sure the transmitter batteries are well loaded .The voltage of transmitter batteries never be lower than 8.6V. And please check and confirm that the servos are all well and properly connected.! Please take off batteries from transmitter after flying and during the transportation.! Please check and have a test on control surfaces to confirm the transmitter handling of each part prior to each takeoff. The frequencies of the module and the receiver should be the same.! The instructor and the student transmitters must accord with each other when using trainer function.! Keep the radio system away from moist, high temperature and strong shake. Do not clean the product with solvent. ! Do not fly your models near airfield, schools, hospitals, residences, power transmission network, communication facilities and other places that are forbidden for starting the transmitter. Please stop flying your models with the radio on rainy or windy days, or at night.! Do not fly the models when you are tired, sick , intoxicated,or not in good spirit.! The antenna do not touch anything else when power switch is turned on. Do not leave this product and its accessories within the reach of small children.! Please use this product according to your local relevant law or regulation,we are not responsible for any incidents or damages.! Important Comments: All USB ports in this transmitter are just used for our special cord with its USB structure and without USB agreement. DO NOT USE your USB cables with transmitter.CautionR/C Introduction Manual 21.1 N-8c功能示意图1.1 N-8C Transmitter Chart!Press “OK/Return” to entry the main menu. (“OK/Return” here in after refered to as“ ”)!Press “Up ” and “Down ” for selecting functions in the list; press“ ” to enter the selected function; press “ ”to return to the previous menu.(“Up ” here in after refered to as“ ”;“Down ” here in after refered to as“ ”)!Press “Increase ”and “Decrease ”to change input data.(“Increase ” here in after refered to as“ ”;“Decrease” here in after refered to as“ ”)Goyr. Sens. Adj. SWAntennaTrainer SWPower SW EyeletHandleIdel. SWElev. D/R SWPit Adj. SWLeft StickLCDAile. D/R SWThro.Hold SWRight StickInput KeysCharging JackUp Down Decrease Increase Ok/Return
R/C Introduction Manual R/C Introduction Manual 432.3 D/R & EXP !FunctionDual rates are available for elevator and rudder channels of RC helicopters. !Operation1. Press “ ” to entry the menu – Roll“ ” or “ ”select the function (D/R & Exp) in the list Press “ ” to set the function and return to the previous menu. 2. Roll “ ” or “ ” to select ELEV and AILE to set the data. 3. ELEV setting ---- ‘ELEV’ is displayedOnce the Elevator D/R switch is on/up, the data displayed is ‘Pos 0’. Use “ ” or “ ” to increase or decrease the data.(2.3.1) Once the Elevator D/R switch is off/down, the data displayed is ‘Pos 1’. Use “ ” or “ ” to increase or decrease the data.(2.3.2) 4. AILE setting ---- ‘AILE” is displayedOnce the Aileron D/R switch is on/up, the data displayed is ‘Pos 0’. Use “ ” or “ ” to increase or decrease the data. (2.3.3)Once the Aileron D/R switch is off/down, the data displayed is ‘Pos 1’. Use “ ” or “ ” to increase or decrease the data. (2.3.4)5.Press “ ” to save and return to the previous menu. [D/R&EXP][D/R&EXP]AILEAILEPos0Pos079%79%D/RLIND/RLIN[D/R&EXP][D/R&EXP]AILEAILEPos1Pos142%42%D/RLIND/RLIN[D/R&EXP][D/R&EXP]ELEVELEVPos0Pos079%79%D/RLIND/RLIN[D/R&EXP][D/R&EXP]ELEVELEVPos1Pos142%42%D/RLIND/RLIN(2.3.1)(2.3.1) (2.3.2)(2.3.2) (2.3.3)(2.3.3) (2.3.4)(2.3.4)2.4 Rev. SWCH 1 2 3 4 5 6 7 8CH 1 2 3 4 5 6 7 8RRNN[REV.SW][REV.SW] THRO THROCH 1 2 3 4 5 6 7 8CH 1 2 3 4 5 6 7 8RRNN[REV.SW][REV.SW] AUX3 AUX3CH 1 2 3 4 5 6 7 8CH 1 2 3 4 5 6 7 8RRNN[REV.SW][REV.SW] ELEV ELEV! Function The Reverse switch is to change the servo for channel direction. ! Operation1.Select ‘REV. SW’ and entry the interface. 2.Use “ ” or “ ” to select the channel arrow position. Press “ ” to reverse the channel; press “ ” to the normal status.3.Press“ ” to save and return to the previous menu.2.2 Function List"[FUNC.LIST]"" D/R & EXP" Dual Rate" Rev. SW" " Sub Trim" Sub Trim " Trvl ADJ." Travel Adjustment" Swash Mix" Swash Mixing" Swash TYP" Swash Type" Stick Mode" Stick Mode" Thro Curv" Throttle Curve" Pit Curv" PIT. Curve" Planes" Planes " Clear" Clear" Gyro Sens" Gyro Sensitivity" Idel Thro" Idle Throttle" Idel Pith" Idle Pitch"PLANE TYPE" PLANE TYPE" Exit" 2.1 Menu!It is a default setting of helicopter in Model Type initially. !When the voltage displayed is 8.6V below, the number will be flashed and simultaneously with warning.U:U:11.5v11.5v8 Channel R/C8 Channel R/CPPM/FMPPM/FMChannel TypeChannel TypeModel TypeVoltageVoltageModulation TypeModulation TypeReversing SwitchReversing Switch T P C A R EOT P C A R EOExit
[SWASH TYP][SWASH TYP]2Servos 2Servos 180180..CCPMCCPM[SWASH TYP][SWASH TYP]3Servos 3Servos 120120..CCPMCCPM[SWASH TYP][SWASH TYP]4Servos 4Servos 9090..CCPMCCPM[SWASH TYP][SWASH TYP]CP MOD CP MOD [SWASH Mix][SWASH Mix]4Servos 4Servos EL +50% EL +50% PI +50% PI +50% AI +50% AI +50%9090..[SWASH MIX][SWASH MIX]3Servos 3Servos EL +50% EL +50% PI +50% PI +50% AI +50% AI +50%120120..[SWASH MIX][SWASH MIX]2Servos 2Servos PI +50% EL +50% PI +50% EL +50% AI +50% AI +50%180180..[SWASH MIX][SWASH MIX]Ser osSer osOn1 oneOn1 oneR/C Introduction Manual R/C Introduction Manual 652.8 Swash Mix!Function This function is to set the swash mixing data. !Operation1.Select ‘SWASH MIX’ and entry the interface. 2.Use “ ” or “ ” to select the channel arrow position. Press “ ” or “ ” to set the mixing data between the Travel value and the Throttle. 3.Press “ ” to save and return to the previous menu. Notes: Please set the ‘Swash TYP’ before entering the Swash Mix.(cp mode;2Servos;3Servos;4Servos;)2.7 Swash TYP!Function This function is to select a Swash type. !Operation1.Select ‘SWASH TYP’ and entry the interface. 2.Use “ ” or “ ” to select the mode: CP mode/2Servos/3Servos/4Servos. 3.Press “ ” to save and return to the previous menu. SWASH TYP2.6 Trvl ADJ.2.5 Sub Trim[Sub.Trim ][Sub.Trim ]THRO -13%THRO -13%ELEV -19%ELEV -19%AILE -20%AILE -20%RUDD +10%RUDD+10% [Sub.Trim ][Sub.Trim ]GEAR -18%GEAR -18%FLAP + 8%FLAP + 8%PITH - 3%PITH - 3%AUX3 +10%AUX3 +10%! Function The Sub trim is a trim position setting on 8 channels. ! Operation1.Select ‘Sub Trim’ and entry the interface. 2.Use “ ” or “ ” to select the channel arrow position. Press “ ” or “ ” to change the data.(2.5.1) 3.Use “ ” or “ ”to display circularly the other channels below. Press “ ” or “ ” to change the data. (2.5.2)4.Press “ ” to save and return to the previous menu.(2.5.1)(2.5.1) (2.5.2)(2.5.2)[TRVL ADJ.][TRVL ADJ.]THRO -13%THRO -13%ELEV -19%ELEV -19%AILE -20%AILE -20%RUDD +10%RUDD+10% [TRVL ADJ.][TRVL ADJ.]GEAR -18%GEAR -18%FLAP + 8%FLAP + 8%PITH - 3%PITH - 3%AUX3 +10%AUX3 +10%! Function The function is an electronic means to adjust the servo travel value.! Operation1.Select ‘TRVL ADJ.’ and entry the interface. 2.Use “ ” or “ ” to select the channel arrow position. Press “ ” or “ ” to change the data.(2.6.1) 3.Use “ ” or “ ”to display circularly the other channels below. Press “ ” or “ ” to change the data. (2.6.2)4.Press “ ” to save and return to the previous menu.(2.6.1)(2.6.1) (2.6.2)(2.6.2)
[Planes][Planes] BBAACCDDEEFFBBR/C Introduction Manual R/C Introduction Manual 872.11 Pit Curv! Function This radio offers 2 separate pitch curves with 5 adjustable points per curve: L/1/2/3/H. ! Operation1.Select ‘PIT. CURV’ and entry the interface.2.Use “ ” or “ ” to select any point at arrow that is in need to reset the data. Press “ ” or “ ” to set the data separately as the curve is being changed accordingly. 3.Press “ ” to save and return to the previous menu. PIT. CURV2.12 Planes! Function This radio has a memory for 6 models with their data individually. ! Operation1.Select ‘PlANES’ and entry the interface.2.Use “ ” or “ ” to select the model memorized with a code. 3..Press “ ” to save and return to the previous menu. [Planes][Planes] FFAACCDDEEFFBB[Planes][Planes] AAAACCDDEEFFBB[PIT. CURV][PIT. CURV]1:1:2525[PIT. CURV][PIT. CURV]L:L:00[PIT. CURV][PIT. CURV]H:H:1001002.9 Stick Mode[STICK MODE][STICK MODE]RIGHT STICK RIGHT STICK MODE 1 MODE 1 [STICK MODE][STICK MODE]LEFT STICK LEFT STICK MODE 2 MODE 2 ! Function This function allows you to exchange mode 1 and mode 2. ! Operation1.Select ‘STICK MODE’ and entry the interface.2.Use “ ” or “ ” to select the mode.3.Press “ ” to save and return to the previous menu. Notes: To change the mode, it is necessary to remove the model of the transmitter. 2.10 Thro Curv! Function This radio offers 2 separate throttle curves with 5 adjustable points per curve: L/1/2/3/H. ! Operation1.Select ‘THRO CURV’ and entry the interface.2.Use “ ” or “ ” to select any point at arrow that is in need to reset the data. Press “ ” or “ ” to set the data separately as the curve is being changed accordingly. 3.Press “ ” to save and return to the previous menu. [THRO CURV][THRO CURV]1:1:2525[THRO CURV][THRO CURV]L:L:00[THRO CURV][THRO CURV]H:H:100100
R/C Introduction Manual R/C Introduction Manual 1092.15 Idel Thro! Function This function is a possibility to adjust the pitch curve with 5 points in 3D mode. ! Operation1.Select ‘IDEL PITH’ and entry the interface.2.Use “ ” or “ ” to select any point at arrow that is in need to reset the data. Press “ ” or “ ” to set the data separately as the curve is being changed accordingly. 3.Press “ ” to save and return to the previous menu. This function is a possibility to adjust the pitch curve with 5 points in 3D mode. IDEL PITH! Function This function is a possibility to adjust the throttle curve with 5 points in 3D mode. ! Operation1.Select ‘IDEL THRO’ and entry the interface.2.Use “ ” or “ ” to select any point at arrow that is in need to reset the data. Press “ ” or “ ” to set the data separately as the curve is being changed accordingly. 3.Press “ ” to save and return to the previous menu. This function is a possibility to adjust the throttle curve with 5 points in 3D mode. IDEL THRO2.16 Idel PithIdel Pith[IDEL THRO][IDEL THRO]1:1:2525[IDEL THRO][IDEL THRO]L:L:00[IDEL THRO][IDEL THRO]H:H:100100[IDEL PITH][ID EL PITH]1:1:2525[IDEL PITH][ID EL PITH]L:L:00[IDEL PITH][ID EL PITH]H:H:100100[Clear][Clear]Reset or no?Reset or no?[N][N][Y][Y]2.13 Clear[Clear][Clear]Reset or no?Reset or no?[N][N][Y][Y]! Function This function helps with returning the factory preset. ! Operation1.Select ‘CLEAR’ and entry the interface. [Y] and [N] are displayed. [Y] is to return the factory preset;(2.13.1) [N] is not to return the factory preset. (2.13.2)2.Use “ ” or “ ” to select the answer. 3.Press “ ” to save and return to the previous menu. (2.13.1)(2.13.1) (2.13.2)(2.13.2)2.14 Gyro Sens[GYRO SENS][GYRO SENS]Pos0Pos0Pos1Pos1 80%80%20%20%[GYRO SENS][GYRO SENS]Pos0Pos0Pos1Pos1 80%80%20%20%! Function This function offers a gyro adjustment with 2 points. ! Operation1.Select ‘GYRO SENS’ and entry the interface. 2.Once ‘the Gyro Sensitivity Adjustment SW’ is off/down, the data displayed is ‘Pos 0’. Use “ ” or “ ” to adjust the data. Once ‘the Gyro Sensitivity Adjustment SW’ is on/up, the data displayed is ‘Pos 1’. Use “ ” or “ ” to adjust the data.3.Press “ ” to save and return to the previous menu. (2.14.1)(2.14.1) (2.14.2)(2.14.2)
R/C Introduction Manual R/C Introduction Manual 1211BBBB Elevator L StickUpwards Plane M O ModeⅠL StickDownwards UDUDElevator3.1 Upright Operation of Left Stick and Movement of Elevator3. Transmitter Operation and Movement (for Airplane)This chapter will introduce transmitter’s stick operation and movement of each servo of aeroplane, including stick operation and movements of Elevator, Rudder, Throttle, Aileron. (Mode 1)Left Stick Vertaical Operation 2.17 PLANE TYPE[SWASH TYP][SWASH TYP]CP MOD CP MOD []PLANE TYPE[]Airplane Airplane V-Tail Mix V-Tail Mix 3D Mix 3D Mix []PLANE TYPE[]Airplane Airplane V-Tail Mix V-Tail Mix 3D Mix 3D Mix []PLANE TYPE[]Airplane Airplane V-Tail Mix V-Tail Mix 3D Mix 3D Mix ! Function This function is loaded with airplane and helicopter programming. ! Operation 1.Select “SWASH TYP” and entry the interface of "CP MOD”. 2.Entry “PLANE TYPE”. 3.Use “ ” or “ ” to select the model type. 4..Press “ ” to save and return to the previous menu. ! Swash Adjustment1. Turn on the transmitter. Press Select keys to enter the Swash Type and select swash type you want.2. Open the horns of swash plate servos.3. Move the throttle stick(engine turned on) to observe the circumvolving direction of the servos horn. By reverse, you can adjust the direction.4. Press Select keys to enter the Sub Trim and return all values to zero.5. Lock the servos' horns.6. Observe the circumvolving direction of the swash plate by moving aileron and elevator. Change it by adjusting the value of aileron and elevator in Swash Mix list.7. Gyro Adjustment------Press Select keys to enter the Gyro Sensor and adjust the value you want by O/I switch.8. Finished all of the above, you can fly your helicopter freely.
R/C Introduction Manual R/C Introduction Manual 1413 M O ModeⅠMotor Plane Decelerating Decelerating Accelerating Accelerating R StickDownwards R StickUpwards Rudder L StickRightwards L StickLeftwards Plane M O Left Stick Horizontal OperationModeⅠR RL L 3.3 Upright Operation of Right Stick and Movement of ThrottleRight Stick Vertaical OperationRudder 3.2 Level Operation of Left Stick and Movement of Rudder3.4 Level Operation of Right Stick and Movement of AileronRi gh t St ic k Ho ri zo nt al O pe ra ti onR StickRightwards R StickLeftwards (Mod eⅠ) M O Left Aileron Right Aileron PlaneD U D R ULR Aileron L Aileron
R/C Introduction Manual R/C Introduction Manual 16154.1 Back of TransmitterModuleTrainerBattery Cover! Connect the student and the instructor transmitters with the trainer cord. Confirm the connection is OK.! The instructor transmitter is used as a normal setting; Turn down the student transmitter and take off its Replaceable Module and batteries. (Do not extend the antenna of student transmitter)! When the trainer switch of the instructor is pushed, like the following illustration, the model can be controlled by student. When the trainer switch of instructor returns, the model is under instructor's control.! The training function is only active with T-1 trainer cord.4. 2 Trainer Function High CapLow Cap ! For your convenient operation, the stick length can be adjusted as your demand.! Screw the high cap anticlockwise to the desired length and then, screw the low cap anticlockwise to lock the high cap as the left illustration.! For your convenient operation, the stick tension can be adjusted as your demand.! Use the screwdriver to adjust the screw clockwise for the desired tension. anticlockwise to loosen stick feel, clockwise to tighten stick feel.! This adjustment need take off the back cover of transmitter.This chapter will introduce the installation and adjustment of some important parts of transmitter, including Control Stick Length and Tension Adjustment, Loading Batteries, Loading Module and Connection between Receiver and Servos. 5.1 Control Stick Length&Tension Adjustment5. Installation and Adjustment
R/C Introduction Manual 186.1 Three-servo Connection Diagram6.1 Three-servo Connection DiagramBCh8CH7CH6CH5CH4CH3CH2CH1BCh8CH7CH6CH5CH4CH3CH2CH1GyroGyroServo 4Servo 4 Servo 3Servo 3Servo 2Servo 2Servo 1Servo 1AILE.AILE.PITCHPITCHELEV.ELEV.RUDD.RUDD.MotorMotorElectronic Speed ControllerElectronic Speed ControllerPowerPowerReceiverReceiver(AILE.)(AILE.)(ELEV.)(ELEV.)(PITCH)(PITCH)FrontFrontR/C Introduction Manual17图 4.3.1! Open the battery cover in the direction of the arrow while pressing the non-slip cover grips.! Load the batteries in accordance with the battery holder polarity marking and close the battery cover.(5.2.1) 5.2.15.2 Loading Batteries
R/C Introduction Manual R/C Introduction Manual 2019BCh8CH7CH6CH5CH4CH3CH2CH1BCh8CH7CH6CH5CH4CH3CH2CH1GyroGyroServo 3Servo 3Servo 2Servo 2Servo 1Servo 1AILE.AILE.ELEV.ELEV.RUDD.RUDD.MotorMotorElectronic Speed ControllerElectronic Speed ControllerPowerPower6.2 Two-servo Connection Diagram6.2 Two-servo Connection DiagramReceiverReceiver(AILE.)(AILE.)(ELEV.)(ELEV.)FrontFront6.3 Four-servo Connection Diagram6.3 Four-servo Connection DiagramBCh8CH7CH6CH5CH4CH3CH2CH1BCh8CH7CH6CH5CH4CH3CH2CH1GyroGyroServo 4Servo 4 Servo 3Servo 3Servo 2Servo 2Servo 1Servo 1AILE.AILE.PITCHPITCHELEV.ELEV.RUDD.RUDD.MotorMotorElectronic Speed ControllerElectronic Speed ControllerPowerPowerReceiverReceiverServo 5Servo 5AUX3AUX3(AUX3) (AUX3) (AILE.)(AILE.)(ELEV.)(ELEV.)(PITCH)(PITCH)FrontFront
R/C Introduction Manual R/C Introduction Manual 2221BCh8CH7CH6CH5CH4CH3CH2CH1BCh8CH7CH6CH5CH4CH3CH2CH1Servo 4Servo 4Servo 2Servo 2Servo 1Servo 1MotorMotorElectronic Speed ControllerElectronic Speed ControllerPowerPower6.4 ACRO Connection Diagram6.4 ACRO Connection DiagramReceiverReceiverServo 3Servo 3 Ch2 Ch6Ch4Ch3 Ch2Ch66.5 V-tail Mixing Connection 6.5 V-tail Mixing Connection BCh8CH7CH6CH5CH4CH3CH2CH1BCh8CH7CH6CH5CH4CH3CH2CH1Servo 2Servo 2Servo 1Servo 1MotorMotorElectronic Speed ControllerElectronic Speed ControllerPowerPowerReceiverReceiver

Navigation menu