Guangzhou Chiyuan Electronic X-3 3CH Radio Control User Manual X 3 mannual

Guangzhou Chiyuan Electronic Co.,Ltd 3CH Radio Control X 3 mannual

Users Manual

SERVO020%100%120%20%100%120%RIGHTFWDLEFTBACKXy3002. With the system hookedup as shown, insert thebind plug in the chargeplug receptacle.Turn onthe power of the receiver(4.8~5.6v), and nowLED(xy300) should beflashing indicating thatthe receiver is ready toAUX Channel Function(CH3)SERVO0100%100%When pressing the “AUX”channel ,the servo moving clockwise,pressing again, anticlockwiseBINDST.D/RF/SFuntionUsing this function to to adjust servo travel.The default is 100%.When pressing D/R ,the front light flash,and the value quickly switch to 70%.FunctionThis F/S Funtion is protect your car or boat,when the signal become weakor lost.How to set1.Make sure the RX power is enough.2.Put trigger in brake position(above show). Keep the F/S button till“ST.DR” become red.3. Then release F/S button, the function finished.Lock FunctionWhen press “RF-TEST” button and “F/S” button together, the frontlight become red, means locked.(Making sure you touch the ST.TRIM ,TH.TRIM and D/R no response). Both press again, means unlocked.1).Keep pressing RF-TEST button till the “ST.DR” light turn on RED.Meanwhile the output power of transmitter reduce to lower mode 18dbm,which done can save the power consumption.2).When press the RF-TEST button again, the “ST.DR” light turn off, andoutput power becomes normal 20dbm which can control more range.RESETFunctionAll the setting in the system will bereset to the default values bythis reset function.1.Press the ST.D/R and put the TH.TRIMforward together, then turn onthe TX at the same time, the light of POWERand ST.DR are flashing, means it is resetting.2.Making sure this function work, you have toturn off TX and turn on it again.LOCKSteering Dual Rates ChoiceST.D/RTH.D/R
SERVO020%100%20%100%RIGHTFWDLEFTBACKTrim Operation And Maximum Travel.Changing the trim can effect the overall settings, whenadjustments are made with the trims, please recheck yourinstallation for maximum servo travel.When Trim movement goes to extremesThat means if you make a lot of trim movement to get a servoto the neutral position, please reposition the servo horn orservo saver on the servo and inspect your linkageinstallation.Throttle TrimThrottle neutral adjustments can be made by moving thethrottle trim to the left or the right.Racers TipWhen using a electronic speed control, please set thethrottle trim to neutral and make adjustments to the speedcontrol. On a gas powered model, set the trim to neutral andadjust the linkage to the point where carburetor is fullyclosed in accordance with the engine instruction manual.Trim Operation and TravelTrim adjustments will effect the overall servo travel, soplease check the (back-ward) movement after the adjustmentWhen trim movement goes to extremesThat means if you make a lot of the trim movement to get theservo to the neutral position, please recenter the servohorn closer to the neutral position and inspect yourthrottle linkage.Receiver Connection DiagramTechnology DataFLASHTURN LEFT TURN RIGHT1 2120%ESCSERVO3(CH3)SERVO1(ST.)SERVO2(TH.)BATT.( 4.8V)ST.TRIMTH.TRIMg rate: 240 Jump/soutput power:<=20dbmworking current:<= 150mAWorking voltage:1.5V*4NiCad/NiMHReceiverChannel:3Frequency:2.4G ISM FREQUENCYSpread spectrum mode: FHSSPower:4.5-7.4V, <30 mAChanges or modifications not expressly approved by the party responsible forcompliance could void the user's authority to operate the equipment.FCC Radiation Exposure StatementThe antennas used for this transmitter must be installed to provide a separation distance ofat least 20 cm from all persons and must not be collocated or operating in conjunction withany other antenna or transmitter.

Navigation menu