Guard RFID Solutions ECB Wireless button for refill of manufacturing parts User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3527110
Application ID	ZI9QiWFp9EdmMc70hvaduA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	92.08kB (1150977 bits)
Date Submitted	2017-08-25 00:00:00
Date Available	2017-08-25 00:00:00
Creation Date	2017-08-24 11:41:39
Document Lastmod	2017-08-24 11:41:39
Document Title	Step by step instructions to preforming features of Staff Duress and Staff Tag
Document Author:	user

E-Kanban Call Button
Installation and Configuration Guide
07-00090-001
E-Kanban Call Button Installation and Configuration Guide
Contents
Contents
About the E-Kanban Call Button .........................................................................................................2
Powering the E-Kanban Call Button ....................................................................................................3
Battery Power ........................................................................................................................................... 3
12VDC Central Supply Power .................................................................................................................... 4
Mounting the E-Kanban Call Button....................................................................................................5
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE
FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
07-00090-001
©2017 Guard RFID Solutions Inc. All Rights Reserved
E-Kanban Call Button Installation and Configuration Guide
About the E-Kanban Call Button
About the E-Kanban Call Button
The E-Kanban Call Button (ECB) is a call button
intended for just-in-time parts replenishment to
assembly lines in manufacturing operations (eKanban). Its true wireless nature enables easy
deployment without need for wired power or
communication lines. Alternately, a hard-wired
power supply can be used if desired.
The ECB has a large multi-color LED indicator which
is constructed in such a way that it can be observed
from a distance in the well-lit environments
characteristic of a production line.
Two large buttons enable workers to call for parts,
and their robust construction allows for rough
handling without fear of damage. Button functions are software configurable.
The ECB communicates to the rest of GuardRFID system utilizing the same infrastructure as
GuardRFID tags, and communication frequency used (433 MHz), ensures reliable 2-way
communication in the most difficult RF conditions. A variety of LED flashing patterns, colors and
buzzer annunciations enable the device to signal a wide spectrum of notifications, under full
control of software application.
▪
Rugged construction suitable for harsh environments
▪
Powered by battery or 12VDC power supply
▪
12 months battery life – Replaceable batteries
▪
2-way communication for sending requests and receiving audio-visual commands
▪
Two configurable buttons for custom functions
▪
Large multi-color LED indicator and buzzer
▪
Splash-resistant
07-00090-001
©2017 Guard RFID Solutions Inc. All Rights Reserved
E-Kanban Call Button Installation and Configuration Guide
Powering the E-Kanban Call Button
Powering the E-Kanban Call Button
You can supply power to the E-Kanban Call Button in two ways:
▪
The device can be powered by four AA batteries.
▪
The device can be connected to a +12VDC power source via its mini CT connector.
GuardRFID recommends that you use both power sources—if the device has access to both
battery power and wired power, the batteries act as a back-up in case the central power supply
fails.
Both the battery compartment and power connector are on the back of the E-Kanban Call Button,
which is typically inaccessible once the device is mounted. Install power sources before mounting
the device.
Battery Power
You can supply power to the E-Kanban Call Button using four AA batteries, which will provide
about 12 months of operating power Battery life varies according on usage frequency.
Note that if the device is powered by both 12VDC wired power and batteries, it uses the wired
power in preference.
Inserting batteries into the E-Kanban Call Button
Using a Phillips screwdriver, remove the three screws on
the back of the device. Remove the battery cover to
expose the battery compartment.
Insert four fresh AA batteries into the compartment,
taking care to orient them according to the diagram
embossed into the compartment’s surface.
Replace the battery cover and secure it in place using the
screws.
07-00090-001
©2017 Guard RFID Solutions Inc. All Rights Reserved
E-Kanban Call Button Installation and Configuration Guide
Powering the E-Kanban Call Button
12VDC Central Supply Power
You can supply power to the E-Kanban Call Button through a 2-pin mini CT connector accessible
through the back of the device. The device requires +12VDC, and should not draw more than
35mA current during normal operation.
Note that if the device is powered by both 12VDC wired power and batteries, it uses the wired
power in preference.
Wiring and connector specifications
▪
The E-Kanban Call Button’s mini CT connector is 2-pin, 2 position, 1.5mm pitch header
connector (Digikey part number A98681-ND). It accepts a 1.5mm pitch female socket
receptacle such as Digikey part number A100192-ND.
▪
The power wire should be 18AWG or thicker.
Connecting the E-Kanban Call Button to 12VDC power
Wire a 2-pin socket receptacle to your 12VDC power source. Be sure to observe the polarity of
the connector (see the diagram below).
Using a coin or similar small, flat object, twist the circular port cover on the
back of the E-Kanban Call Button counter-clockwise ¼ turn to unlock it.
Remove the cover.
Plug the socket receptacle into the 2-pin connector. Lay the wires in the cable trough (see the
diagram below).
Line up the arrow on the circular port cover to the OPEN
arrow on the back of the device, then press it into place.
Provided the wires are thin, the port cover should fit
into place
Turn the port cover clockwise ¼ turn to lock it.
Cable
trough
07-00090-001
©2017 Guard RFID Solutions Inc. All Rights Reserved
E-Kanban Call Button Installation and Configuration Guide
Mounting the E-Kanban Call Button
Mounting the E-Kanban Call Button
The E-Kanban Call Button is a robust device designed for industrial environments, and can be
mounted to a hard surface or left unmounted for portability (although this latter option will make
wired power difficult).
Note that mounting the device usually makes it difficult to access the back of the device. Be sure
to insert batteries/wire the device to power, and to record the device’s serial number, before
mounting it.
Bolts or screws
The E-Kanban Call Button can be mounted to a
solid surface using screws or bolts. Thread the
bolts through the holes at either end of the
device. Note that you will have to unfasten the
device to access the battery compartment or
connectors.
Tie wraps
The E-Kanban Call Button can be mounted to a
post or grate using tie wraps. Thread the tie
wraps through the slots at either end of the
device. Note that you will have to cut the tie
wraps to access the battery compartment or
connectors.
Adhesives
You can mount the E-Kanban Call Button to a surface using double-sided adhesive pads, but this is
not typically recommended. Although adhesive pads will not damage the device and can provide
secure mounting, they are also more difficult to remove than fasteners and may obscure the
device serial number label. Use this method only if you do not need to regularly access the back of
the device (i.e., if you are primarily using wired power).
07-00090-001
©2017 Guard RFID Solutions Inc. All Rights Reserved

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
Page Count                      : 6
Language                        : en-US
Tagged PDF                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Microsoft® Word 2016
Title                           : Step by step instructions to preforming features of Staff Duress and Staff Tag
Creator                         : user
Creator Tool                    : Microsoft® Word 2016
Create Date                     : 2017:08:24 11:41:39-07:00
Modify Date                     : 2017:08:24 11:41:39-07:00
Document ID                     : uuid:6EF47AE1-4958-48AD-8E48-75FBC5EBE3E6
Instance ID                     : uuid:6EF47AE1-4958-48AD-8E48-75FBC5EBE3E6
Author                          : user

EXIF Metadata provided by EXIF.tools