HAN Networks AP23X HAN Access Point User Manual Statement

HAN Networks Co., Ltd. HAN Access Point Statement

Contents

User Manual (Statement)

HAN Access Point:
AP231 and AP231e Regulatory
Compliance and Safety Information
XXXXXX-XX Rev. C
*XXXXXX-XX Rev. C*
Introduction
This document contains domestic and international regulatory
compliance information for the access point. To ensure that this
device complies with the regulatory standards for your region,
please refer to the content below.
For United States
FCC Statement: Improper installation of access points in the
United States configured to non-US model controllers will be in
violation of FCC rules. Any such willful or intentional violation
may result in a requirement by the FCC for immediate
termination of operation and may be subject to forfeiture (refer
to 47 CFR 1.80).
EU Statement: Low power radio LAN products operating in 2.4
GHz and 5 GHz bands. Please refer to the User Guide for details
on restrictions.
For product available in the USA market, only channels 1~11 can
be operated. Selection of other channels is not possible. This
device is restricted for indoor use.
This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Operations in the 5.15-5.25GHz band are restricted to indoor
usage only.
Users should also be advised that high-power radars are allocated
as primary users (i.e. priority users) of the bands 5250-5350 MHz
and 5650-5850 MHz, and that these radars could cause
interference and/or damage to LE-LAN devices.
FCC Class B Part 15:
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including
interference that may cause undesired operation.
Any changes or modifications to this unit not expressly
approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
This equipment has been tested and compliant with the limits for
a Class B digital device under part 15 of the FCC Rules. This
equipment generates, uses, and can radiate radio frequency
energy. If it is not installed and used in accordance with HAN’s
instructions, it may cause harmful interference. If this equipment
does cause interference, which can be determined by turning the
equipment off and on, the user is encouraged to correct the
interference in one or more of the following ways:
Reorient or relocate the antenna.
Increase the separation between the equipment and other
devices.
Connect the equipment to an outlet on a circuit different
from that to which the other device is connected.
Consult the dealer or an experienced radio technician for
help.
California Proposition 65 Warning
WARNING: This product contains chemicals known to the State of
California to cause cancer and birth defects or other reproductive
harm.
For EU
HAN Networks Co., Ltd., hereby declares that these models are
compliant with the essential requirements and other provisions of
Directive 2014/53/EU. For the complete CE DoC, please access
the website below to get more information:
www.han-networks.com
Waste Electrical and Electronic Equipment (WEEE) Statement
HAN products are subject to separate
collection and treatment in the EU Member
States, Norway, and Switzerland when they are
at end of life, and therefore are marked with
the symbol shown. The treatment applied to
these products in these countries shall be
compliant with the applicable national laws
which are under the implementing of Directive 2012/19/EU on
Waste of Electrical and Electronic Equipment (WEEE).
European Union RoHS
HAN products are compliant with the EU Restriction of Hazardous
Substances Directive 2011/65/EU (RoHS). EU RoHS restricts the
use of specific hazardous materials in the manufacture of
electrical and electronic equipment. The restricted materials
under the Directive are Lead (including Solder used in printed
circuit assemblies), Cadmium, Mercury, equivalent Chromium, and
Bromine.
Global RF health information:
RF Radiation Exposure Statement: This equipment complies
with FCC and CE RF radiation exposure limits. This equipment
should be installed and operated with a minimum distance of
35 cm between the equipment and a human’s body for 2.4 GHz
and 5 GHz operations. This transmitter must not be co-located
or operating in conjunction with any other antenna or
transmitter.
For Model AP231, the frequency, mode, and the maximum
transmitted power in EU are listed below:
2412-2472MHz (802.11b 1 Mbps): 17.84dBm
2412-2472MHz (802.11g 6 Mbps): 19.53dBm
2412-2472MHz (802.11n HT20 MCS0): 19.46dBm
2412-2472MHz (802.11n VHT40 MCS0): 19.34dBm
5180-5240MHz (802.11a 6 Mbps): 22.05dBm
5260-5320MHz (802.11a 6 Mbps): 21.99dBm
5500-5700MHz (802.11a 6 Mbps):29.13dBm
5180-5240MHz (802.11n HT20 MCS0): 22.06dBm
5260-5320MHz (802.11n HT20 MCS0): 22.12dBm
5500-5700MHz (802.11n HT20 MCS0):29.04dBm
5180-5240MHz (802.11n VHT40 MCS0): 22.12dBm
5260-5320MHz (802.11n VHT40 MCS0): 22.08dBm
5500-5700MHz (802.11n VHT40 MCS0):29.28dBm
5180-5240MHz (802.11ac VHT80 MCS0): 22.14dBm
5260-5320MHz (802.11ac VHT80 MCS0): 22.09dBm
5500-5700MHz (802.11ac VHT80 MCS0):29.12dBm
For Model AP231e, the frequency, mode, and the maximum
transmitted power in EU are listed below:
2412-2472MHz (802.11b 1 Mbps): 17.74dBm
2412-2472MHz (802.11g 6 Mbps): 19.46dBm
2412-2472MHz (802.11n HT20 MCS0): 19.37dBm
2412-2472MHz (802.11n VHT40 MCS0): 19.30dBm
5180-5240MHz (802.11a 6 Mbps): 22.43dBm
5260-5320MHz (802.11a 6 Mbps): 22.25dBm
5500-5700MHz (802.11a 6 Mbps):29.31dBm
5180-5240MHz (802.11n HT20 MCS0): 22.20dBm
5260-5320MHz (802.11n HT20 MCS0): 22.26dBm
5500-5700MHz (802.11n HT20 MCS0):29.34dBm
5180-5240MHz (802.11n VHT40 MCS0): 22.39dBm
5260-5320MHz (802.11n VHT40 MCS0): 22.41dBm
5500-5700MHz (802.11n VHT40 MCS0):29.41dBm
5180-5240MHz (802.11ac VHT80 MCS0): 22.20dBm
5260-5320MHz (802.11ac VHT80 MCS0): 22.12dBm
5500-5700MHz (802.11ac VHT80 MCS0):29.32dBm
The device is restricted to indoor use only when operating in the
5150 to 5350 MHz frequency range.

Navigation menu