HAN Networks AP24X HAN Access Point User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3737688
Application ID	lxDIx8lSMswS9ARxv5U6JQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	69.02kB (862727 bits)
Date Submitted	2018-02-02 00:00:00
Date Available	2018-08-02 00:00:00
Creation Date	2018-02-01 16:01:08
Producing Software	Microsoft® Office Word 2007
Document Lastmod	2018-02-01 16:01:08
Document Title	User Manual
Document Creator	Microsoft® Office Word 2007
Document Author:	深圳2

HAN Access Point AP241 AP241e
Installation Guide


4- or 8-conductor, CAT5 or better UTP cable of required length.
Power sources:
a) For full-function running mode (Tri-Radio,2.4GHz 4x4:4 +
5GHz 4x4:4), the following two kinds of power sources are
acceptable
1) IEEE 802.3at compliant PoE source with LLDP
protocol supported, 60W, output voltage DC
48V(nominal), or
2) AC/DC adapter (sold separately) ，output
voltage DC 48V, output current > 0.75A
When both power sources are available, DC power takes priority over
PoE
b) For Power safe mode (Tri-Radio,2.4GHz 2x2:2 + 5GHz
2x2:2, USB disabled), an IEEE 802.3at compliant PoE
source is acceptable

A PC terminal or a notebook
Summary of installation Steps







Unpack the AP box and check all contents
Install the AP bracket on ceiling or wall
Installing the AP
Connecting required cables
Power connection
Verifying post-installation connectivity
AP provisioning
AP is a radio transmission device and subject to governmental regulation.
Network administrators must comply with local regulations.
Package Contents
Item
Name
Access Point
Quick Start Guide
Installation Guide
Regulatory Compliance and Safety
Information
User Guide Info Card
Mounting Bracket (15/16”)
Mounting Bracket (9/16”)
Qty
Unit
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Pcs
Figure 2: AP Front View
Identifying Specific Installation Locations
You can mount the HAN Access Point on a ceiling rail (using the
shipped bracket in the box) or on a wall (using the wall mount adapter,
sold separately). You should first determine the location of the
installation. The installation position is located at the center of the
required coverage area and should be free from obstructions or
obvious sources of interference.


Minimize the number of obstructions (such as walls) between the AP
and user terminals.
Electronic equipment or devices (such as microwave ovens) which
may produce radio frequency noise should be away from the
installation position of the AP.
It is strictly prohibited to install around stagnant water, water seepage,
leakage or condensation. Avoid cable condensation or water seepage
along the cables connecting to the AP.
Temperature and Humidity requirement

Operating temperature: 32ºF to 113ºF (0ºC to 45ºC)

Storage temperature: -40ºF to 158ºF (-40ºC to 70ºC)

Relative Humidity: 10% to 90% non-condensing
AP Installation
Figure 1: Product Packing
Inform your HAN sales representative of incorrect, missing, or
damaged parts. If possible, retain the carton, including the
original packing materials. Use these materials to repack and
return the unit to the supplier if needed. Additional mounting kits
for use with the HAN Access Point AP241/AP241e are sold
separately. Contact your HAN sales representative for details.
Unboxed AP241/AP241e:

Net Weight: 3.34lbs / 1.516kg

Dimensions (H×W×D): 9.1 inches × 9.1 inches × 1.81 inches
(23 cm × 23cm × 4.6cm)
Figure 3: AP Back View
Item Name
RESET
USB
1Gigabit
Ethernet
2.5Gigabit
Ethernet
CONSOLE
Device view
The HAN Access Point is equipped with one hidden LED light that
indicates different status with distinct color or flashing.
48VDC
Kensington
Lock Slot
Specifications
Factory reset. Press reset button for 5s, AP LEDs will
quickly flash for 3s, then AP will restart and restore
factory configurations.
USB 2.0 host interface (Type A connector)
1x 10/100/1000BASE-T autosensing (RJ-45) port,
Power over Ethernet (PoE)
1x 100/1000/2.5GBASE-T autosensing (RJ-45) port,
Power over Ethernet (PoE)
The console port is an RJ-45 female connector and
can be used to connect to a terminal for direct local
management.
Note: Currently for use by Service & Support only.
The AP has a single 48V DC power jack socket to
support powering through an AC-to-DC power
adapter. If PoE is not available, an optional AC-DC
adapter kit (sold separately) can be used to power
the AP.
The AP is equipped with a Kensington lock slot for
additional security.
Table 1: External Interfaces
Pre-Installation Checklist
Before installing your HAN Access Point, be sure that you have the
following items:
Using Ceiling Mounting Bracket
Make sure the AP fits securely on the ceiling tile rail when hanging
the device from the ceiling, poor installation could cause it to fall
onto people or equipment.
The HAN Access Point has been shipped with two mounting brackets for
9/16” and 15/16” ceiling rails. Following is the general sequence to
install the AP with the mounting bracket.

Pull the cables through a prepared hole in the ceiling tile near
where the AP will be placed.

Place the bracket against the back of the AP, insert by aligning the
slot on the backside with the hanging feet on both sides of the
bracket (see Figure 4).

Push the bracket along the direction of the arrow until it locks in
the slot (see Figure 4).

Connect the cable to the port on the AP.

Hold the AP next to the ceiling tile rail with the ceiling tile rail
mounting slots at approximately a 20-degree angle to the ceiling tile
rail (see Figure 5). Make sure that any cable slack is above the
ceiling tile.

Pushing toward the ceiling tile, rotate the AP clockwise until the
device clicks into place on the ceiling tile rail (see Figure 5).
Flash
System running
ON
System running
ON
System running
Flash
Flash
System running
Flash
Flash
Figure 4: Attaching the Ceiling Mounting Bracket
Flash
System running
Network normal, without
SSID created
Network normal, single
band working, either
2.4GHz or 5Ghz
Network normal, dual bands
working, 2.4Ghz and 5Ghz
are both working
Red and Blue LEDs alternate
flashing in specific
frequency; OS upgrading
3 LEDs alternate flashing in
specific frequency; Used for
locating an AP
Table 3 HAN Access Point LED Meaning
Console Port
The serial console port allows you to connect the AP to a serial terminal
or a laptop for direct local management. This port is an RJ-45 female
connector with the pinouts described in Table 4.
Figure 7
Note: Currently for use by Service & Support only.
Connector
Signal Name
TXD
GND
GND
RXD
Function
Pins not listed are not connected
Figure 5: Mounting the AP
Connect Ethernet
Use the Ethernet port to connect the AP with a twisted pair Ethernet LAN
segment. Use a 4- or 8-conductor, Category 5 UTP cable. The port is an
RJ-45 female connector with the pinouts shown in Table2.
Ethernet Port
Signal
Pin
Function
/RJ45 Female
Name
BI_DA+ Bi-directional pair +A, PoE Negative
BI_DABi-directional pair -A, PoE Negative
BI_DB+ Bi-directional pair +B, PoE Positive
BI_DC+ Bi-directional pair +C, PoE Positive
BI_DCBi-directional pair -C, PoE Positive
BI_DBBi-directional pair -B, PoE Positive
BI_DD+ Bi-directional pair +D, PoE Negative
BI_DDBi-directional pair -D, PoE Negative
Pin
Table 4: Console Port Pinout
Configuring the HAN Access Point
Refer to the Quick Start Guide and Configuration Guide for complete
details.
If both PoE and DC power are available, the use of DC is preferred.
HAN Access Point supports the power adapter provided by HAN
ONLY.
Verifying Post-Installation Connectivity
The LED on the AP can be used at this point to verify that the AP is
receiving power and initializing successfully (see Table 3).
Red
ON
ON
Flash
Blue
Green
Time
Line
Power on
Bootloader-OS
loading
System running
Status
System start up
Network abnormal
(Interface down)
The external antennas are sold separately.
Unboxed AP241e (external antenna)

Net Weight: 3.48lbs / 1.58kg

Dimensions (H×W×D): 9.1 inches × 9.1 inches × 1.81 inches (23 cm x
23cm × 4.6cm)
Device view
Table 2: Ethernet Port Pinout
Connect Power Sources
Confirm that the Ethernet cable is loaded either with 48V DC (nominal)
60W/802.3at compliant PoE source (with LLDP protocol) for full-function
running mode, or just with 802.3at compliant PoE source for power safe
mode.
If not, connect by using the HAN 48V AC-DC adapter kit (sold separately)
to the DC Power Socket and AC power jack.
Figure 8: With external antennas
[REMAINING SECTIONS INTENTIONALLY LEFT BLANK]
Figure 6
It is installed in the same way as AP241 for the AP installation. In Figure 7,
it is shown the way to install the external antennas.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 2
Language                        : zh-TW
Tagged PDF                      : Yes
Author                          : 深圳2
Creator                         : Microsoft® Office Word 2007
Create Date                     : 2018:02:01 16:01:08+08:00
Modify Date                     : 2018:02:01 16:01:08+08:00
Producer                        : Microsoft® Office Word 2007

EXIF Metadata provided by EXIF.tools