HANK ELECTRONICS BWD19AAA08 WIRELESS CHARGING CLOCK RADIO WITH BLUETOOTH SPEAKER User Manual
HANK ELECTRONICS CO., LTD. WIRELESS CHARGING CLOCK RADIO WITH BLUETOOTH SPEAKER
User_Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 4176022 |
| Application ID | ESpaHJs4JrAEWbVkGuG0Rw== |
| Document Description | User_Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 171.59kB (2144839 bits) |
| Date Submitted | 2019-02-22 00:00:00 |
| Date Available | 2019-02-22 00:00:00 |
| Creation Date | 2019-02-14 10:33:03 |
| Producing Software | Adobe PDF library 15.00 |
| Document Lastmod | 2019-02-14 10:33:03 |
| Document Title | User Manual |
| Document Creator | Adobe Illustrator CC 22.1 (Windows) |
Features Top TM WIRELESS CHARGING CLOCK RADIO WITH BLUETOOTH SPEAKER Model: BWD19AAA08 PRODUCT USER GUIDE ① Item Mode button Description Press to cycle between FM mode, BT mode and AUX mode (when Aux-in jack is connected ) ② Alarm button In Clock mode, press to turn on or turn off alarm; In other modes, press to return to Clock mode; In any mode, press and hold 1 second to enter alarm clock settings. ③ Clock button In other modes, press to return to Clock mode; In any modes, press and hold 1 second to enter clock settings. ④ Dimmer/Snooze/Sleep When alarm rings, you can press to adjust the interval to repeat alarm. The alarm repeats ringing 10 minutes later. When alarm not rings, press it to adjust LED brightness, press and hold 2 seconds to set up sleep timer. ⑤ Volume Down/ Previous Track In BT mode, press to switch to previous track; In FM Mode, press to tune in 0.1MHz increments or switch preset stations, double-click to start auto scan until find a lower available channel, and press and hold to decrease volume. In any modes, press and hold to decrease volume. Ver.01 Rev. 01/05/19 Ver.01 Rev. 01/05/19 LED Digital Display In AUX mode and BT mode, press to play or pause audio; in FM mode, press to enter preset station play mode, press and hold 2 seconds to set preset station. ⑥ Play/Pause ⑦ Volume Up/Next Track In BT mode, press to switch to next track; In FM Mode, press to tune in 0.1MHz increments or switch preset stations, double-click to start auto scan until find an upper available channel. In any modes, press and hold to increase volume. Rear ① Item AUX IN jack Description Connect to an external audio device. ② FM antenna The FM antenna is an 80cm pigtail cable, keep it fully extended to get the best signal reception. ③ USB port Connect to charge an external device. ④ DC IN jack Connect to the included power adapter. ① Item Current time Description Displays the current time. ② AM/PM “AM” lights after midnight and before noon, and “PM” lights after noon and before midnight. ③ Alarm Lights when alarm has been set and enabled. ④ Bluetooth Lights when BT mode is selected. ⑤ AUX Lights when an external audio is connected. ⑥ FM Lights when FM mode is selected. ⑦ MHz Lights when FM mode is selected. Package Contents • 1x Clock Radio • 1x 5V/3.2A Power Adapter • 1x User Guide • 1x Quick Start Guide Ver.01 Rev. 01/05/19 Ver.01 Rev. 01/05/19 Play FM Radio Connect to Power - Risk of product damage! Use the include 5V power adapter ONLY. Connect the AC power cord to the wall socket. Set Clock Time In any modes, press and hold button for 1 second, you will see the LED hour section blinks, then press or button to adjust the hour, after hour is set, press button to switch to minute, the LED minute blinks, then press or button to adjust the minute, after minute is set, press to confirm setting (If no button is pressed for 15 seconds, the setting is saved automatically). Set Alarm Time In any modes, press and hold button for 1 second, you will see the LED hour section blinks, then press or button to adjust the hour, after hour is set, press button to switch to minute, then press or button to adjust the minute, after minute is set, press button to confirm setting (If no button is pressed for 15 seconds, the setting is saved automatically). Set Alarm Sound After set the alarm minute, press button two times to enter alarm tone selection, then press or button to choose the tone you want (4 tones plus 1 FM radio tone), after tone is set, press button to confirm setting (If no button is pressed for 15 seconds, the setting is saved automatically). Turn On/Off Alarm Press button to turn off or turn on alarm, the LED alarm icon keeps off or on correspondingly. Adjust LED Brightness When alarm no sounds, short press three levels for selection. button to adjust LED brightness, there are low, medium and high Play Audio from a Bluetooth Device The first time you connect your Bluetooth device to this player, you need to pair your device to this player. Return Factory Default Press button for 10 seconds until “beep”, the previous Clock settings, Alarm settings and Bluetooth paring settings will be cleared. Use Snooze Feature 1) You can press to repeat alarm. When alarm rings, press 2) When alarm rings, press any button (except 1) The default mode upon power on is FM mode. In other modes, press button to switch to FM mode. ( FM supports 87.5MHz to 108MHz) 2) Press or button to tune frequency for 0.1MHz each time, double-click or button to start auto scan, it stops until a station is found, auto scan will be interrupted by press or button. 3) Tune to the radio station you want to program, then press and hold button for 2 seconds to enter preset mode. The next available preset number (P-01 through P-10) appears on the LED. If you want to use a different preset number, press or button repeatedly until the number you want appears on the LED,then press button again to save your station and exit preset mode with “beep” voice prompt. (If no button is pressed for 15 seconds, the setting is saved automatically). 4) Press button to enter play preset station mode, and the last played preset station number (P-01 through P-10) appears on the LED, then press or button repeatedly until the preset station you want appears on the LED. Press button again to exit play preset station mode. 5) Press and hold or button to adjust volume, the volume level number appears on LED. button to snooze for 10 minutes. button). The alarm stops, but the alarm settings remain. Set the Sleep Timer In BT/AUX/FM modes, press and hold button to adjust sleep timer, there are “90/60/30/15 minutes” and “OFF” total 5 options, after you get to the desired option, let go off button to confirm selection. Note: • The operational range between this player and a Bluetooth device is approximately 10 meters (without any object between the Bluetooth device and the unit). • Compatibility with all Bluetooth devices is not guaranteed. • Any obstacle between this unit and a Bluetooth device can reduce the operational range. • If the signal strength is weak, your Bluetooth receiver may disconnect, but it will re-enter pairing mode automatically. 1) Press button to switch to BT mode, you will hear a “Bluetooth Mode” prompt tone, and clock radio automatically enters Bluetooth pair with Bluetooth name “Blackweb Clock Radio”, there will be a “Bluetooth Pairing” prompt tone if pairing success and you will hear “Bluetooth Disconnected” when disconnected. 2) Press and hold button for 1 second to disconnect the current connected device, clock radio re-enters paring status. 3) When Bluetooth is disconnected, press button and clock radio will reconnect with the device that has connected before. 4) Press and hold or button to adjust volume, the volume level number appears on LED. Ver.01 Rev. 01/05/19 Ver.01 Rev. 01/05/19 Connect an External Audio Device FCC RF EXPOSURE STATEMENT: 1)In any mode, plug an audio cable with a 3.5 mm connector (not included) into the AUX IN jack on the back of your clock radio and into the audio out jack on your audio device, clock radio enters AUX mode automatically and plays the audio from your audio device, LED AUX icon keeps on. 2)Press and hold or button to adjust volume, the volume level number appears on LED. ISEDC CAUTION: Wireless Charging a Mobile Device 1) Plug in the included 5V/3.2A power adapter and your clock radio is powered on. 2) Make sure your device supports Qi charging technology. 3) Put your device horizontally on the wireless stand, DO NOT put it vertically as this will make it beyond charging arrange. 4) Your device will show charging status if charge successfully. Charge a Mobile Device via USB-A Port 1) Plug in the included 5V/3.2A power adapter and your clock radio is powered on. 2) Connect a USB cable (not provided) to the USB port on the back of your clock radio and to the USB port on your device. 3) Your device will show charging status if charge successfully. FCC WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Ver.01 Rev. 01/05/19 This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with Innovation, Science, and Economic Development Canada licence exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. ISEDC RF EXPOSURE STATEMENT: The device is in compliance with RF exposure guidelines, users can obtain Canadian information on RF exposure and compliance. IMPORTANT LEGAL INFORMATION IMPORTANT SAFEGUARDS: When using an electrical product, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING • WARNING: Listen responsibly. To avoid hearing damage, make sure the volume on your device is turned down before connecting to the speaker. After turning on your speaker, gradually turn up the volume until you reach a comfortable listening volume. • Use this product only for its intended use as described in this manual. Do not use attachments not recommended by Blackweb. • Blackweb is not liable for any damage caused to smartphones, iPod/MP3 players, or any other device. • Do not place or store this product where it can fall or be dropped into a tub or sink. • Do not place or drop into water or any other liquid. • Not for use by children. THIS IS NOT A TOY. • Never operate this product if it has a damaged cord, plug, cable, or housing. • Keep away from heated surfaces. • Only set on dry surfaces. Do not place on surfaces wet from water or cleaning solvents. Please use the standard power adapter equipped with this unit. The charging input and output ports, please do not connect to any faulty equipment to avoid the irreversible damage of the unit. Do not use in a strong magnetic or strong interference field, otherwise it may cause the machine to be functionally unusual. The product is for indoor use only. A MESSAGE FROM THE ENVIRONMENT WARNING: This product has an internal, non-replaceable lithium-ion battery. Please dispose of in accordance with your local, state, province, and country guidelines. This product contains small parts that may present a choking hazard for young children. CAUTION: All servicing of this product must be performed by authorized service personnel only. Blackweb is a trademark of Walmart Stores, Inc. The ‘Qi’ symbol is a trademark of the Wireless Power Consortium. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc., and any use of such marks by Blackweb is under license. Distributed by Walmart Stores, Inc., Bentonville, AR; 72716 1-800-925-6278 . 2018 Walmart Stores, Inc. All rights reserved.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No XMP Toolkit : Adobe XMP Core 5.6-c143 79.161356, 2017/09/07-01:11:22 Format : application/pdf Title : User Manual Metadata Date : 2019:02:14 10:33:03+08:00 Modify Date : 2019:02:14 10:33:03+08:00 Create Date : 2019:02:14 10:33:03+09:00 Creator Tool : Adobe Illustrator CC 22.1 (Windows) Thumbnail Width : 256 Thumbnail Height : 128 Thumbnail Format : JPEG Thumbnail Image : (Binary data 15776 bytes, use -b option to extract) Instance ID : uuid:f720cce1-37b2-4c63-a966-8f4511558af6 Document ID : xmp.did:6cdc7483-ee47-414e-84cc-5d19ec188aab Original Document ID : uuid:5D20892493BFDB11914A8590D31508C8 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:4c5340ac-ced5-bc46-aa76-5bf0d73d2348 Derived From Document ID : xmp.did:4c5340ac-ced5-bc46-aa76-5bf0d73d2348 Derived From Original Document ID: uuid:5D20892493BFDB11914A8590D31508C8 Derived From Rendition Class : proof:pdf History Action : saved, saved History Instance ID : xmp.iid:a173c0d2-b9ae-ab4f-bfc8-154a38a92c7a, xmp.iid:6cdc7483-ee47-414e-84cc-5d19ec188aab History When : 2019:01:05 14:39:58+08:00, 2019:02:14 10:33+08:00 History Software Agent : Adobe Illustrator CC 22.1 (Windows), Adobe Illustrator CC 22.1 (Windows) History Changed : /, / Manifest Link Form : EmbedByReference Manifest Reference File Path : C:\Users\WM\Desktop\图片1.png Ingredients File Path : C:\Users\WM\Desktop\图片1.png Startup Profile : Print Has Visible Overprint : True Has Visible Transparency : True N Pages : 1 Max Page Size W : 200.000029 Max Page Size H : 209.999997 Max Page Size Unit : Millimeters Font Name : PirulenRg-Regular, MyriadPro-Cond, MyriadPro-SemiboldCond, MyriadPro-Regular, MyriadPro-BoldCond, MyriadPro-Semibold, AdobeSongStd-Light Font Family : Pirulen, Myriad Pro, Myriad Pro, Myriad Pro, Myriad Pro, Myriad Pro, Adobe 宋体 Std Font Face : Regular, Condensed, Semibold Condensed, Regular, Bold Condensed, Semibold, L Font Type : Open Type, Open Type, Open Type, Open Type, Open Type, Open Type, Open Type Font Version : Version 3.001, Version 2.106;PS 2.000;hotconv 1.0.70;makeotf.lib2.5.58329, Version 2.007;PS 002.000;Core 1.0.38;makeotf.lib1.7.9032, Version 2.106;PS 2.000;hotconv 1.0.70;makeotf.lib2.5.58329, Version 2.106;PS 2.000;hotconv 1.0.70;makeotf.lib2.5.58329, Version 2.106;PS 2.000;hotconv 1.0.70;makeotf.lib2.5.58329, Version 5.017;PS 5.002;hotconv 1.0.67;makeotf.lib2.5.33168 Font Composite : False, False, False, False, False, False, False Font File Name : PirulenRg-Regular.otf, MyriadPro-Cond.otf, Myriad-Pro-Semibold-Condensed.ttf, MyriadPro-Regular.otf, MyriadPro-BoldCond.otf, MyriadPro-Semibold.otf, AdobeSongStd-Light.otf Plate Names : Cyan, Magenta, Yellow, Black Swatch Group Name : 默认色板组, 灰色, 明亮 Swatch Group Type : 0, 0, 0 Swatch Colorant Swatch Name : 白色, 黑色, CMYK 红, CMYK 黄, CMYK 绿, CMYK 青, CMYK 蓝, CMYK 洋红, C=15 M=100 Y=90 K=10, C=0 M=90 Y=85 K=0, C=0 M=80 Y=95 K=0, C=0 M=50 Y=100 K=0, C=0 M=35 Y=85 K=0, C=5 M=0 Y=90 K=0, C=20 M=0 Y=100 K=0, C=50 M=0 Y=100 K=0, C=75 M=0 Y=100 K=0, C=85 M=10 Y=100 K=10, C=90 M=30 Y=95 K=30, C=75 M=0 Y=75 K=0, C=80 M=10 Y=45 K=0, C=70 M=15 Y=0 K=0, C=85 M=50 Y=0 K=0, C=100 M=95 Y=5 K=0, C=100 M=100 Y=25 K=25, C=75 M=100 Y=0 K=0, C=50 M=100 Y=0 K=0, C=35 M=100 Y=35 K=10, C=10 M=100 Y=50 K=0, C=0 M=95 Y=20 K=0, C=25 M=25 Y=40 K=0, C=40 M=45 Y=50 K=5, C=50 M=50 Y=60 K=25, C=55 M=60 Y=65 K=40, C=25 M=40 Y=65 K=0, C=30 M=50 Y=75 K=10, C=35 M=60 Y=80 K=25, C=40 M=65 Y=90 K=35, C=40 M=70 Y=100 K=50, C=50 M=70 Y=80 K=70, C=0 M=0 Y=0 K=100, C=0 M=0 Y=0 K=90, C=0 M=0 Y=0 K=80, C=0 M=0 Y=0 K=70, C=0 M=0 Y=0 K=60, C=0 M=0 Y=0 K=50, C=0 M=0 Y=0 K=40, C=0 M=0 Y=0 K=30, C=0 M=0 Y=0 K=20, C=0 M=0 Y=0 K=10, C=0 M=0 Y=0 K=5, C=0 M=100 Y=100 K=0, C=0 M=75 Y=100 K=0, C=0 M=10 Y=95 K=0, C=85 M=10 Y=100 K=0, C=100 M=90 Y=0 K=0, C=60 M=90 Y=0 K=0 Swatch Colorant Mode : CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK Swatch Colorant Type : PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS Swatch Colorant Cyan : 0.000000, 0.000000, 0.000000, 0.000000, 100.000000, 100.000000, 100.000000, 0.000000, 14.843800, 0.000000, 0.000000, 0.000000, 0.000000, 4.687500, 19.921900, 50.000000, 75.000000, 84.765600, 89.843800, 75.000000, 79.687500, 69.921900, 84.765600, 100.000000, 100.000000, 75.000000, 50.000000, 34.765600, 9.765600, 0.000000, 25.000000, 39.843800, 50.000000, 54.687500, 25.000000, 29.687500, 34.765600, 39.843800, 39.843800, 50.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 84.765600, 100.000000, 59.765600 Swatch Colorant Magenta : 0.000000, 0.000000, 100.000000, 0.000000, 0.000000, 0.000000, 100.000000, 100.000000, 100.000000, 89.843800, 79.687500, 50.000000, 34.765600, 0.000000, 0.000000, 0.000000, 0.000000, 9.765600, 29.687500, 0.000000, 9.765600, 14.843800, 50.000000, 94.921900, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 94.921900, 25.000000, 44.921900, 50.000000, 59.765600, 39.843800, 50.000000, 59.765600, 64.843800, 69.921900, 69.921900, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 100.000000, 75.000000, 9.765600, 9.765600, 89.843800, 89.843800 Swatch Colorant Yellow : 0.000000, 0.000000, 100.000000, 100.000000, 100.000000, 0.000000, 0.000000, 0.000000, 89.843800, 84.765600, 94.921900, 100.000000, 84.765600, 89.843800, 100.000000, 100.000000, 100.000000, 100.000000, 94.921900, 75.000000, 44.921900, 0.000000, 0.000000, 4.687500, 25.000000, 0.000000, 0.000000, 34.765600, 50.000000, 19.921900, 39.843800, 50.000000, 59.765600, 64.843800, 64.843800, 75.000000, 79.687500, 89.843800, 100.000000, 79.687500, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 100.000000, 100.000000, 94.921900, 100.000000, 0.000000, 0.000000 Swatch Colorant Black : 0.000000, 100.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 9.765600, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 9.765600, 29.687500, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 25.000000, 0.000000, 0.000000, 9.765600, 0.000000, 0.000000, 0.000000, 4.687500, 25.000000, 39.843800, 0.000000, 9.765600, 25.000000, 34.765600, 50.000000, 69.921900, 100.000000, 89.843800, 79.687500, 69.921900, 59.765600, 50.000000, 39.843800, 29.687500, 19.921900, 9.765600, 4.687500, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000 Producer : Adobe PDF library 15.00 Page Count : 2 Creator : Adobe Illustrator(R) 17.0 AI Creator Version : 22.1.0 For : WM, Bounding Box : 46 108 1212 684 AI Build Number : 312 AI Color Usage : Color AI Ruler Units : Millimeters AI Color Model : CMYK AI Target Resolution : 800 AI Num Layers : 2 Container Version : 11 Creator Version : 22 Image Height : 576 Image Width : 1166 Image Size : 1166x576 Megapixels : 0.672EXIF Metadata provided by EXIF.tools