HDT H168 Handheld 3-Axis Gimbal Stabilizer User Manual

HDT(SZ)CO., LIMITED Handheld 3-Axis Gimbal Stabilizer

User manual

 USER MANUAL  Handheld 3 Axis Gimbal Stabilizer   H2
3 Axis Parameter & Indicator Light         Indicator Light:    Instruction is received and executing.    Working well in normal voltage.    Low voltage,flashing is too low to shutdown.   When stabilizer overloaded,red&blue light will flashing, motor will stop output and try output after 10 seconds. If keeping failed after 5 times, stabilizer enter self protection(Mainly related to phone weight balance).    System is working abnormally.     2700 1800 3200 NO.2 Motor(Roll)  NO.3 Motor(Tilt)  NO.1 Motor(Pan)
Product Overview:    Attention! Please install smartphone or action camera first before power on.        When using IPhone6, IPhone7, IPhone8, pull guide holder to innermost position.    When using IPone6 Plus, IPone7 Plus, pull guide holder to middle.    Please adjust guide holder position according to your phone weight.      In the bottom, there is a 1/4 thread inside to connect with self-stick and other accessories.    Knob: --tighten when clockwise rolling. --loosen when counter clockwise rooling
 Instruction 1:              No.1 Motor(Pan)  Joystick Button: Up and Down:Control Tilt Motor to move up and down. Left and Right:Control Pan Motor to move right and left. Power Button: Power off status:Long press until indicator light turn blue and flash, the stabilizer power on. Double click:Camera back to middle. Shooting Button: Single click:Taking photo. Double click:Switch front and rear camera of phone. Triple click:Switch photo and video shooting.    Micro USB Charging Port No.3 Motor(Tilt)
 Instruction 2:             Lock switch: Pull up:Unlock No.3 Motor (Tilt),enter following mode. Pull down:Lock No.3 Motor (Tilt),shutdown following mode. Pulley switch: Pull down:Reduce following speed when pulling switch down, enter fix shooting when pull down to bottom (3 motors been fixed). Pull up:Unlock fix mode when pull switch up(accelerate following speed when pulling switch up).    Switch horizontal to vertical shooting: At horizontal shooting status: keep phone facing to yourself, rotate handle of stabilizer over 70 degrees in counterclockwise, stabilizer enter vertical shooting(phone camera downward) At horizontal shooting status: keep phone facing to yourself, rotate handle of stabilizer over 70 degrees in clockwise, stabilizer enter vertical shooting(phone camera upward)  Switching vertical to horizontal shooting: At vertical shooting status: keep phone facing yourself, handle of stabilizer upright, exit vertical shooting mode.  Hand-adjusting: Adjusting Pan&Tilt by hands when indicator light at green or red status。   No.3 Motor(Tilt) No.2 Motor(Roll) NO.1 Motor(Pan)
 Packing List:  No. Name Quantity 1 Gimbal Stabilizer X1 2 USB Charging Cable X1   Specification:  Name Specification Charging voltage 5V Charging current 1A Working voltage 3.4V  ~  4.2V Working current 0.2mA  ~ 2A No.1 Motor(Pan) -160°  ~  160° No.2 Motor(Roll) -90°  ~  90° No.3 Motor(Tilt) -180°  ~  90° Battery duration About 4H Working temperature -10°C  ~  45°C Net weight(including battery) About 400g Product dimension(L/W/H) 320*124*55mm
  Federal Communications Commission (FCC) Statement  This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.      Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:        ●Reorient or relocate the receiving antenna. ●Increase the separation between the equipment and receiver.             ●Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.       ●Consult the dealer or an experienced radio/TV technician for help.          Warning: Changes or modifications made to this device not expressly approved by HDT(SZ)CO., LIMITED may void the FCC authorization to operate this device.         Note:  The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

Navigation menu