HES 9800 Series Installation Guide HES9800Install Instructions
User Manual: HES HES 9800 Series Installation Guide Installation Guide
Open the PDF directly: View PDF 
.
Page Count: 4
| Download | |
| Open PDF In Browser | View PDF |
HES 9800 | Adams Rite 7800 Electric Strike ® ® Installation Instructions and Frame Preparation Product Components Diagram 1: Product Components A HES 9800 | Adams Rite 7800 Strike Body A B HES 9800 | Adams Rite 7800 Cover B C 1/4"-20 x 1" Mounting Screws D #10-32 & 10-24 Lockdown Screws (optional) E #6-32 x 1/4" Cover Screws F 5/64" Hex Key G 12-Volt and 24-Volt Pigtails H 1/8" and 1/16" Spacers Electrical Specifications Electrical Ratings for Solenoid Voltage 12 VDC 24 VDC Resistance in Ohms 24 96 mA Continuous Duty 450 250 Solenoids are rated at +/- 10% indicated value. Minimum Wire Gauge Requirements Solenoid Voltage 12 VDC 24 VDC 200 feet or less 18 gauge 22 gauge 200 – 300 feet 16 gauge 22 gauge 300 – 400 feet 16 gauge 20 gauge (Based on Round Trip) C F H D UL1034 • Static Strength: 1500 lbs E • Dynamic Strength: 70 ft – lbs • Endurance: 250,000 cycles UL294 Performance Levels G • Destructive Attack: Level I • Line Security: Level I • Endurance: Level IV • Standby Power: Level I NOTE: Installation wiring for the product and wiring methods shall be in accordance with the National Electrical Code, ANSI/NFPA70 1 CAUTION Before connecting any device at the installation site, verify input voltage using a multimeter. Many power supplies and low voltage transformers operate at higher levels than listed. Any input voltage exceeding 10% of the solenoid rating may cause severe damage to the unit and will void the warranty. Preparing the Strike Diagram 1: 12V to 24V Conversion Diagram 2: If Connector Is Missing For 12 VDC, the Plug In Connector (pigtail) marked “12 VDC” should be used; for 24 VDC, the pigtail marked “24 VDC” should be used. Electric Strike Red • SELECT the appropriate pigtail that matches system power and electrically CONNECT as illustrated in Diagram 1. • IF no connector is present, THEN CONFIGURE the wires as shown in Diagram 2. or Red Electric Strike The HES 9800 | Adams Rite 7800 Electric Strike is pre-set for FAIL SECURE OPERATION as shown in Diagram 3. Diagram 3: Fail Secure Operation Converting the Operation Mode There are two Selector Stop Pins, one on the left side and one on the right side. Both Selector Stop Pins must be repositioned (as shown in Diagram 4) to convert the strike to FAIL SAFE OPERATION. IN FAIL SAFE OPERATION: Both keepers should be unlocked without power but locked when power is applied. Selector Stop Pin Location Diagram 4: Fail Safe Operation • MOVE the Selector Stop Pins to the FAIL SAFE OPERATION position (towards the center of the strike) as shown in Diagram 4. • TIGHTEN both Selector Stop Pins after they have been moved to the FAIL SAFE OPERATION position using the 5/64” hex key. FAIL SAFE OPERATION mode should not be used in fire rated or windstorm-resistant applications. 2 Selector Stop Pin Location (+ 12 VDC) (- NEG) Connect Together (+ 24 VDC) Violet Connect Together Black Red/green Verifying the Operation Mode • To convert to FAIL SAFE OPERATION, REMOVE the Selector Stop Pins on each side of the strike body using the provided 5/64" hex key. Black Red/green • IF using the Latchbolt Monitor (LBM) or Latchbolt Strike Monitor (LBSM), THEN REFER to Diagrams 5 and 6 to complete wiring (see page 3). • VERIFY that both keepers are in FAIL SECURE OPERATION. Violet Connect Together (- NEG) Preparing the Frame When mounting on an aluminum frame, with a blade stop, an HES 9000-ASB (sold separately) is necessary to provide a secure installation. The HES 9000-ASB is shown installed in Diagrams 8 and 9. • IDENTIFY and MARK the latchbolt centerline on the frame. • Using the dimensions provided on page 4, MARK all appropriate holes. If using a HES 9000-ASB, reference the installation instructions provided with that product. NOTE: This may require the exit device to shift horizontally towards the hinge side of the door to compensate for the HES 9000-ASB. Diagram 5 Latchbolt Monitor White Orange Green White Common Normally Open Normally Closed Orange Green • PUNCH, DRILL and TAP the marked holes as required. Finishing the Installation • ELECTRICALLY CONNECT the HES 9800 | Adams Rite 7800 to the Plug In Connector, and ATTACH the electric strike to the jamb using the 1/4"-20 x 1" mounting screws provided. Diagram 6 Latchbolt Strike Monitor Brown Blue Yellow Common Normally Open Normally Closed Brown Blue Yellow • CHECK the starwheel interaction with the keepers to ensure proper engagement and clearance. The starwheel’s latchguard needs to be centered within the keepers as seen in Diagram 7. If horizontal adjustment is needed, use one or both of the spacers to provide latch guard/keeper clearance. Additional spacers can be ordered separately. Adjusting Horizontal and Lockdown • TIGHTEN the two 1/4"-20 x 1" mounting screws. • SECURE the adjustment by tightening the set screws. Shown in Diagram 8 on page 4. • OPTIONAL LOCKDOWN FEATURE: INSTALL the #10-24 UNC or 10-32 UNF lockdown screw if additional security is required; however, REMOVE the strike before drilling hole. If using a HES 9000-ASB it will require drilling and tapping of the lockdown hole. • INSTALL the cover plate, and SECURE in place using the #6-32 x 1/4" Cover Screws as illustrated in Diagram 9 on page 4. Diagram 7: Starwheel & Keeper Cross-section Latchguard should be centered between the keepers. HES 9000-ASB Starwheel (optional) Keepers Latchuard 3 Dimensions NOTE: May not be to scale. For easy installation, the HES 9000-MTK should be ordered. Diagram 8 1-3/4" [44.5mm] Mounting Screw HES 9000-ASB (optional) Lockdown Screw (optional) Set Screw Location Final Lockdown Feature 10-32 UNF or 10-24 UNC Screw (optional) Set Screw Location 1/2" [12.7mm] Clearance for LBM/LBSM Wiring 4-1/8" [104.8mm] Mounting Screw 1-1/16" [27mm] 1-5/16" [33.3mm] Diagram 9 This edge toward door Centerline of Latchbolt 1-5/16" [33.3mm] 9" [228.6mm] HES 9000-ASB (optional) 2X Mounting Hole Locations for 1/4-20 UNC Mounting Screws Mounted on Aluminum Frame with HES 9000-ASB Mounted on Hollow Metal Frame techsupport.esh@assaabloy.com | assaabloyesh.com 800.626.7590 | 10027 S. 51st Street Phoenix, AZ 85044 USA 4 3/4" [19mm] Clearance for Power Wiring 4-1/8" [104.8mm] 4X 7/8" [22.5mm] 3026006.005_1 Copyright © 2018, Hanchett Entry Systems, Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Hanchett Entry Systems, Inc. is prohibited.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Create Date : 2018:11:09 08:07:11-07:00 Creator : Adobe InDesign CC 14.0 (Macintosh) Modify Date : 2018:11:09 08:07:22-07:00 Language : en-US XMP Toolkit : Adobe XMP Core 5.6-c015 91.163280, 2018/06/22-11:31:03 Metadata Date : 2018:11:09 08:07:22-07:00 Creator Tool : Adobe InDesign CC 14.0 (Macintosh) Instance ID : uuid:9f859102-705c-644f-a349-74504946ca2c Original Document ID : adobe:docid:indd:c6d5a1b8-1ec5-11dc-9031-b975861f0985 Document ID : xmp.id:5c9a50e9-f126-46d0-bb1e-ef6ad6ae860b Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:7cd410c8-de55-46c6-bd3c-10e2e60c3408 Derived From Document ID : xmp.did:d405c3a6-9123-4add-96b9-277f6f815587 Derived From Original Document ID: adobe:docid:indd:c6d5a1b8-1ec5-11dc-9031-b975861f0985 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CC 14.0 (Macintosh) History Changed : / History When : 2018:11:09 08:07:11-07:00 Format : application/pdf Producer : Adobe PDF Library 15.0 Trapped : False Page Layout : SinglePage Page Count : 4EXIF Metadata provided by EXIF.tools