HHC Changzhou CB18HHC004 Control Box User Manual CB18 Control Box Instructions V1

Download:
Mirror Download [FCC.gov]
Document ID	2728489
Application ID	TgAZfS5EX2D9sMQS6ZPUcg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	14.02kB (175215 bits)
Date Submitted	2015-08-27 00:00:00
Date Available	2015-08-27 00:00:00
Creation Date	2015-08-25 09:20:19
Producing Software	Acrobat Distiller 9.0.0 (Windows)
Document Lastmod	2015-08-25 09:20:19
Document Title	Microsoft Word - CB18 Control Box Instructions-V1
Document Creator	PScript5.dll Version 5.2.2
Document Author:	jack.chen

CB18 Control Box Instructions
1. Product Overview
Product Name：
Control Box
Product Model No.： CB18
FCC ID:
2AEQWCB18HHC004
2. Environment requirement
Operation temperature: +10℃~ +40℃.
Storage temperature: －10℃~65℃.
Operating Humidity：10%~80%RH，non‐condensing.
Storage Humidity：10%~ 85%RH，non‐condensing.
3.
Directions for Operation
To use the control box, the PSK2920A switch power supply must be connected as the control
box power supply. The CH18 remote control must also be paired to be used. Detailed usage for
each port is as follows:
Before use, the CH18 remote control and CB18 control box must be paired:
Press and hold the button, approx. 15 seconds, until the remote’s front indicator lights
up. Then, connect it to the control box Power plug. After the beep sound, the pairing is complete
and remote can operate.
Indicator
light
1/3
LED
Connection
SYNC Cord
Connection
Head Motor Port
USB
Connection
Power Input connection
Head Massage
Motor Port
Foot Massage
Motor Port
Foot Motor Port
Tilt Motor Port
4. The port is introduced
4.1 “HD Motor”：Connects to the Head motor, and lifts/lowers head section.
4.2 “FT Motor”：Connects to the Foot motor, and lifts/lowers foot section.
4.3 “Tilt Motor”：Connects to the Tilt motor, and adjusts tilt.
4.4 “Power”：Connects to the power supply box, controls power supply.
4.5 “USB”：Connects to the USB adapter box, and USB adapter box and USB socket connection.
4.6 “LED”：Connects with lights.
4.7 “SYN”：Same steps. Connect another control box, and two control boxes will synchronize
4.8 “HD Massage”：Connects to Head massage motor, controls strength of head massage and
on/off.
4.9 “FT Massage”： Connects to Foot massage motor, controls strength of foot massage and
2/3
on/off.
5. Matters needing attention：
5.1 The function will only work normally in proper working power conditions.
5.2 Control box input voltage must be less than 29.2VDC.
5.3 The CH18 remote control is needed for proper control.
5.4 If problems are identified, they must be treated by professional personnel.
6. Additional attention for user：
6.1 This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/ TV technician for help.
6.2 This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
6.3 This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. End users must follow the specific operating instructions for satisfying RF exposure
compliance. To maintain compliance with FCC RF exposure compliance requirements, please
using a minimum separation distance of 5 mm from the device.
This transmitter must not be co‐located or operating in conjunction with any other antenna
or transmitter.
6.4 For Intentional and unintentional radiators the manual shall caution the user that changes
or modifications not expressly approved by the party responsible for compliance could void the
users authority to operate the equipment
3/3

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : jack.chen
Create Date                     : 2015:08:25 09:20:19+08:00
Modify Date                     : 2015:08:25 09:20:19+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Format                          : application/pdf
Title                           : Microsoft Word - CB18 Control Box Instructions-V1
Creator                         : jack.chen
Creator Tool                    : PScript5.dll Version 5.2.2
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Document ID                     : uuid:fdb0bd2f-57a4-45ad-b0c8-05bef65fbb06
Instance ID                     : uuid:f453bda3-8f67-4d74-a1b8-aeabf8b1e0fd
Page Count                      : 3

EXIF Metadata provided by EXIF.tools