HID Global 1351 ProxPass 1351 (1351- 300) User Manual 1351A Manual

HID Global Corporation ProxPass 1351 (1351- 300) Users Manual 1351A Manual

Users Manual 1351A Manual

REV DESCRIPTION DATE APPROVED1 INITIAL REVIEWNOTE: Cover sheet is for Revision Control only, and is not to be sent with document.REVSHEET 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 50 51 52REVSHEET 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33REV STATUS 1111OF SHEETS 0123456789101112131415TOLERANCES APPROVALS DATE HID CORPORATION.XX = +/- .03” DWN D.RUBEO IRVINE, CALIFORNIA.XXX = +/- .010” CHK Installation ManualANGLES = +/- 1°APVD Power Prox Active TransponderVehicle Transponder ID TagMATERIAL N/A APVDFINISH N/A P/N 1351-901 REV 1
SCALE N/A SIZE A SHEET 0 OF 3
____________________________________________________________________________________________HID Corporation 9292 Jeronimo Road Irvine, CA 92618-1905 USA TEL (714) 598-1600 (800) 237-PROX (7769)FAX (714) 669-5623 Web page, E-mail - www.prox.com PowerProx Active Transponder, Vehicle Identification TagInstallation Manual 1351-901 REV 1 1 of 3Installation Manual - 1351-901 Rev 1Power Prox Active Transponder, Vehicle Identification Tag
____________________________________________________________________________________________HID Corporation 9292 Jeronimo Road Irvine, CA 92618-1905 USA TEL (714) 598-1600 (800) 237-PROX (7769)FAX (714) 669-5623 Web page, E-mail - www.prox.com PowerProx Active Transponder, Vehicle Identification TagInstallation Manual 1351-901 REV 1 2 of 3PowerProx VEHICLE TRANSPONDER ID TAG Installation ManualOverviewThe Vehicle Transponder ID tag, a 3.7 x 2.7-inch rectangular tag is mounted to the inside of your vehicle’swindshield. This tag has an adhesive backing with a release liner to provide protection until installation canbe obtained. For best results mount tag to lower left (driver’s) side of windshield. If this can not beobtained locate tag anywhere in the far left (driver’s) side. See Figure 2 below for the desired location.Installation Procedure:1. The tag may be in a transport (lock mode), in which case it does not transmit data to the reader. Ifso, it may be taken out of lock mode by bringing it into read range of a HID MaxiProx reader forapproximately 12 seconds. This may be done either before or after installation into the vehicle. Oncethis is done, the tag will operate normally.2. Determine the appropriate mounting position of the tag. Clean area completely free from grease, oil orany other debris, using rubbing alcohol or glass cleaner.3. Remove the release liner from Velcro strips. Position and place strips firmly against back of tag.Figure 1. Place mating strips on inside of windshield. Put even pressure on entire surface of strips toensure adhesion.Figure 1.
____________________________________________________________________________________________HID Corporation 9292 Jeronimo Road Irvine, CA 92618-1905 USA TEL (714) 598-1600 (800) 237-PROX (7769)FAX (714) 669-5623 Web page, E-mail - www.prox.com PowerProx Active Transponder, Vehicle Identification TagInstallation Manual 1351-901 REV 1 3 of 3Figure 2WindshieldDashboardDriver's SidePreferred IDTag locations
____________________________________________________________________________________________HID Corporation 9292 Jeronimo Road Irvine, CA 92618-1905 USA TEL (714) 598-1600 (800) 237-PROX (7769)FAX (714) 669-5623 Web page, E-mail - www.prox.com PowerProx Active Transponder, Vehicle Identification TagInstallation Manual 1351-901 REV 1 4 of 3Regulatory ApprovalsFCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to thefollowing two conditions: (1) this device may not cause harmful interference, and (2) this device mustaccept any interference received, including interference that may cause undesired operation. FCC IDNumber: JQ61351

Navigation menu