HID Global 4045 User Manual manual

HID Global Corporation manual

Contents

manual

RPT00129/25/98Information needed to fill out CEPT ETS 300 330 application forms.1. Quality Assurance: Yes2. If yes, Certification/Accreditation Body(s): ANSI-RABStandard(s) (i.e. ISO 9001, EN45001, etc. ISO90012. If the equipment has previously been type approved to any other ETS orI-ETS, please list. ___NONE________________________________________.3. Choose Type of equipment: Transceiver ♦ Fixed Station, ♦ Duplex. ♦ Integral antenna ♦ Transponder (Tag): Passive (EUT is a READER which reads PASSIVE TAGS).4. ITU Class of Emission Code (s): 1K10P0N--5. Product Class: CLASS 1 ♦ Class 1 Equip. Avg. area for the loop: 0.0023_m26. Transmitter:♦ Method of frequency generation: 4.0 MHz CERAMIC RESONATOR.♦ Operating Frequency: 0.125 MHz♦ Frequency Alignment Range: 0.119 MHz to 0.133 MHz.♦ Channel switching frequency range: single channel♦ Channel separation: __na____♦ Max. Channels of Operation: _one_____♦ Operates without modulation? Yes♦ Transmitter modulation: none♦ Maximum Rated Transmitter Output: 6.0 dB(µA/m)♦ Antenna: multi-turn wire loop7. RF Software Version: _Beta 7______________________.8. RF Power: (tick appropriate box) Power at permanent external RF connector Effective Radiated Power (ERP) Effective Isotropic Radiated Power (EIRP)Maximum measured power: __________________Watts
RPT00129/25/989. Is transmitter output power: FixedIf continuously variable or stepped:Minimum Power ___________A/dB(µA/m) Minimum Power __________WattsIf stepped: Step size __________dB/step10. Is transmitter intended for continuous duty or intermittent duty? CONTINUOUS DUTY (Unit automatically duty cycles transmitter 25 msec on, 100msec off, repeating continuously, without operator intervention)If intermittent: ♦ Tx ON ___ _____ Tx OFF _sec ♦ Duty Cycle (Tx on / (Tx on + Tx off)) = ♦ Continuous operation possible for testing ? Yes or NoDuring Test: Tx ON ______sec Tx OFF ______sec11. Signalling/Digital Transmission:Is selective signalling and/or digital transmission fitted: NoIf yes, is selective signalling and/or digital transmission analogue or digital.If analogue, state format:_________________________________Tone frequencies: _________________________________HzIf digital, state modulation method: _________________________Bit Rate: _____________________bit/sec12. Transmitter Power Source: ♦ Common power source for transmitter and receiver: Yes. ♦ AC Power supply: No. State voltage_______ V. Single or Three phase. ♦ AC supply frequency _________Hz. ♦ DC Power supply: Yes. State voltage: 12 V ♦ DC Maximum Current: .15 A ♦ Other:_____________________________Battery: Nickel Cadmium, Mercury, Alkaline, Lead Acid, Leclanche, Lithium or other ________________________, __________ Volts13. Transmitter modulation: Amplitude, Frequency, Phase or other____NONE________.14. Transmitter Frequency or Phase modulation: for < 12% of the channel separation at _____HzAmplitude Modulation: for 60% modulation depthor declare the maximum modulation depth:______%.
RPT00129/25/9815. Modulation input signal level at: ♦ Microphone socket ______mV Impedance _____Ohms ♦ Accessory socket ______mV Impedance _____Ohms ♦ *Other ______mV Impedance _____Ohms*(For use where direct connection is provided for test purposes.) ♦ Lowest audio modulation frequency transmitted by the equipment: _______Hz16. Transmitter Modulation bit rate ______bit/s.Type of modulation: ♦ Subcarrier: MSK or FFSK. ♦ Direct: Direct FSK , GMSK , Generalized tamed FM or Multilevel.State FM: ♦ PLL-4PSK or 8 PSK.17. Interface for data transmission: ♦ Signal Level: V28 or other (details) ________________________________. ♦ Definition of signals: V24 or other (details)__________________________.18. Can the EUT transmit continuous bit streams? ♦ If NO, give details of the format ________________________________.19. Type of connector: 25 pin RS232, 9 pin RS232, Male, Female or other(details)__________________________________.20. Receiver Technical Characteristics: ♦ Operating Frequency (frequencies) : ___14 KH__________________. ♦ Receiver frequency alignment range: _____none__________________. ♦ Channel switching frequency range: ____none____________________. ♦ Channel separation:__none____. ♦ Maximum number of channels: __1__. ♦ IF Bandwidth: __no IF________________. ♦ Sensitivity: __________________________. ♦ Antenna: ____common to transmit, multiturn wire loop___________.21.Class of emission used (Receiver):ITU Designation 1: -(if applicable) 2:22. Receiver Power Source: ♦ AC Power supply: No. State voltage_______ V. Single or Three phase. ♦ AC supply frequency _________Hz. ♦ DC Power supply: Yes State voltage: ___12____V ♦ DC Maximum Current: ____________A ♦ Other:_____________________________Battery: Nickel Cadmium, Mercury, Alkaline, Lead Acid, Leclanche, Lithium or other ________________________, __________ Volts
RPT00129/25/9823. External power source:Voltage Pin assignment Cable lengthPower source 1 12 WIRE UP TO 152 mPower source 2 mPower source 3 mGround WIRE UP TO 152 m24. If the equipment is designed to automatically switch off at a predetermined voltagelevel, please list cut-off voltage ________.25. Duplex Operation: ♦ Is equipment intended for duplex operation: Yes ♦ Is equipment fitted with separate transmitter and receiver ant. sockets: No. ♦ Is equipment fitted with a duplex filter as an integral part of the equipment with asingle antenna connection socket: Yes or No. ♦ Is the duplex filter externally fitted and connected to the main equipment by co-axialcable(s) Yes or No. If Yes state type and make of duplexfilter_______________________________.26. Frequency Identification:Equipment ID(eg serial no.) Channel No.(If applicable) Transmit NominalFrequency (MHz) Receive NominalFrequency (MHz)27. Integral Selective Calling: _________________________________28. Audio-frequency interface level at external data socket:_______________________________29. Antenna socket: None.30. Data, control and signal ports:Port designation Port number Pin assignment Cable lengthWIEGAND IO WIRES UP TO 152 mLOCAL IO &Control WIRES UP TO 6 mm
RPT00129/25/98m

Navigation menu