HID Global 630XA 6130B RK40, 6131B RWK400 iCLASS Readers User Manual 6094 901
HID Global Corporation 6130B RK40, 6131B RWK400 iCLASS Readers 6094 901
Contents
- 1. Users Manual
- 2. User Manual
User Manual
Installation Guide
iCLASS Reader Models RK40 & RWK400
An ASSA ABLOY Group company ASSA ABLOY
_____________________________________________________________________________________________________
HID Corporation 9292 Jeronimo Road Irvine, CA 92618-1905 USA TEL (949) 598-1600 (800) 237-7769 FAX (949) 598-1690
Web page - www.hidcorp.com e-mail – tech@hidcorp.com iClass Keypad Reader Install Manual 6094-901 Rev A Page 1 of 2
PARTS INCLUDED SPECIFICATIONS
• 1 - iCLASS Keypad Reader • Voltage Range: 12VDC (10 - 16VDC).
• 1 - Installation Manual • Current: 100mA avg / 220mA peak.
• 2 - 3.5mm x .6 pitch x 12mm Phillips machine screws • Cable distance to Host: 500ft (152m) max – Wiegand.
• 3 - #6-32 x .375” Phillips self-tapping machine screws 50ft (15m) max – RS-232.
• 2 - #6 x 1.5” Phillips sheet metal screws 4000ft (1216m) max – RS-485.
• 1 - #6-32 x .375” Spanner security screw • Op. Temperature: -31°F - +149°F (-35°C – +65°C)
Recommended: • Open collector output: Sink – 40mA, source – 1mA.
• Up to 10 wire splices * Standards:
• Cable, 9 conductor, 22AWG, shielded (Wiegand)
• Cable , 6 conductor, 22AWG, shielded (Serial)
• Read/Write* capability in ISO 1SO 15693-2 mode with HID
iCLASS credentials.
• Linear DC Power Supply
• Metal or plastic junction box
• Security Tool (for security screw) HID 04-0001-03
• Read/Write* capability in ISO 1SO 14443-B mode with HID
iCLASS 16KS.
• Magnetic Tamper switch - Ademco 945T, Sentrol
1038T, GRI 100T or 110T or Aleph DC-2531
• Read capability of CSN/UID in ISO 1SO 14443-A1 mode
with HID Mifare and other 3rd party Mifare credentials.
* RK40 available with 18” wire pigtail or 10-pos. removable
screw terminal connector. RWK400 includes 8-pos. and 10-
pos. removable screw terminal connectors.
* RK40 is a read only, while RWK400 is a read/write unit.
INSTALLATION
1- Disassemble
A. Remove the screw at the bottom of the unit.
B. Lift the mounting plate out at the bottom side
C. Slide mounting plate down
2- Install Tamper Switch
An internal magnet provides tamper indication when used with a magnetic reed switch connected to an external alarm
system. Locate Switch behind the left side of the mounting plate, centered between the mounting holes.
Electrical Back Box Wall Surface
Installation Guide
iCLASS Reader Models RK40 & RWK400
An ASSA ABLOY Group company ASSA ABLOY
_____________________________________________________________________________________________________
HID Corporation 9292 Jeronimo Road Irvine, CA 92618-1905 USA TEL (949) 598-1600 (800) 237-7769 FAX (949) 598-1690
Web page - www.hidcorp.com e-mail – tech@hidcorp.com iClass Keypad Reader Install Manual 6094-901 Rev A Page 2 of 2
3- Install Mounting Plate
Attach the mounting plate onto the back box or a wall surface. Dimensions are in inches (centimeters).
OPTIONAL SPACER
MOUNTING PLATE
0.156 /
0.40 cm
1.650 /
4.19 cm
2.000 /
5.08 cm
3.280 /
8.33 cm
0.220 / 0.56 cm
0.300 /
0.76 cm
1.650 / 4.19 cm
2.000 / 5.08 cm
0.175 / 0.44 cm
0.110 / 0.28 cm
0.355 / 0.90 cm
1.550 /
3.94 cm
1.550 / 3.94 cm
1.130 /
2.87 cm
0.080 / 0.20 cm
1.000 / 2.54 cm
4.490 /
11.40 cm
4- Connecting
Serial Port (Model RWK400 Only) Wiegand Port (Models RK40, RWK400)
8 Pin Terminal Function 10 Pin Terminal Color-coded Pigtail Function
1 Ground 10 Violet Open Collector1
2 Y / RS-232 TX 9 Blue Hold1
3 Z 8 Yellow Speaker1
4 Ground 7 Drain Shield Ground2
5 RS485B / RS-232 RX 6 Brown Red LED1
6 RS-485A 5 Orange Green LED1
7 Ground 4 White Data 1
8 DC+ 3 Green Data 0
2 Black Ground
1 Red +DC (10-16 VDC)3
1 Optional Connections
2 Drain wire can be used for data return line when a separate power supply is used.
3 +DC, Return & Drain wires are common between the Wiegand and Serial Ports.
4 In RS-485 mode, pin 2 must be connected to pin 6 and pin 3 must connected to pin 5 with jumpers at the connector.
5- Testing
A. Turn Power On – Watch the sign-on LED and hear the speaker tone sequences.
B. Read Card – Present a valid card to the reader and verify the visual and audio feedbacks.
6- Mounting
Reverse the procedure in step 1 to attach the unit to the mounting plate.
Optional Features
FCC WARNING:
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause undesired operation. For proper regulatory compliance, the drain wire
should be disconnected at the power supply end of the cable. The reader is intended to be powered from a limited power source output of a previously certified
power supply. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
RS232/485 interface/Host Mode - for applications requiring a serial link. See Protocol Document 6090-902 for information
Open Collector Output – controls an external device (13.8VDC Max). See iCLASS Application Note for details
Configuration Options - Configure LED, Speaker, and other features. See How To Order Guide or iCLASS Application Note for details
Hold Input – when asserted, this line either buffers a card read or disables a card read until released, as configured.