HID Global ER40C ER40C , RFID Reader User Manual EdgeReader EdgePlus Installation Guide

Download:
Mirror Download [FCC.gov]
Document ID	1232797
Application ID	OSPncxQzlzOZ9gyEYelcig==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	253.66kB (3170716 bits)
Date Submitted	2010-01-25 00:00:00
Date Available	2010-01-25 00:00:00
Creation Date	2009-12-10 14:35:26
Producing Software	Adobe PDF Library 9.0
Document Lastmod	2010-01-25 17:21:23
Document Title	EdgeReader & EdgePlus Installation Guide
Document Creator	Adobe InDesign CS4 (6.0.4)
Document Author:	L Hanna

Edge
15370 Barranca Parkway
Irvine, CA 92618-2215
USA
EdgeReader® and EdgePlus®
Models: EH400, EHR40, EHRP40, EH400-K
ER40C, ERP40C
Installation Guide
82000-920, Rev A.1
December 10, 2009
© 2009 HID Global Corporation. All rights reserved.
Edge is the next evolution in access control hardware solutions. A true IP solution that meets the demands of open architecture, IP-centric
environments, Edge provides fully distributed intelligence and decision making right to the door, leveraging the IT infrastructure to the
maximum extent possible. Wire the Edge device to Hi-O interface modules to provide connectivity to electronic door components and
access control readers.
Specifications
CONNECTION
PARAMETER
Voltage - Nominal
PoE Power
(input)
Current - Normal Standby
Condition (NSC)
Current - Maximum
VALUE
48 VDC
CAN PWR - not loaded
75 mA
CAN PWR - max load
275 mA
12 VDC - 24 VDC
12 VDC
CAN PWR disconnected
190 mA
Current - Normal Standby
Condition (NSC)
24 VDC
CAN PWR disconnected
110 mA
Current - Maximum
12 VDC
2.2 A
Current - Maximum
24 VDC
2.1 A
Current - Normal Standby
Condition (NSC)
CAN PWR
(output)
CONDITIONS
Voltage
+DC (input)
RA
FT
Hi-O involves devices with built-in intelligence and a CANbus that links all the devices together. Hi-O CANbus data traffic can be password
protected and encrypted, or both. Each Hi-O device (such as the push plate, electric strike, card reader, door operator) is connected to the
CANbus by a single, four-wire cable. Two of the wires supply power and the other two are used for data communication.
Voltage - Nominal
PoE
24 VDC
Current - Maximum
PoE
300 mA
Voltage - Nominal
+ DC
+ DC
Current - Maximum
+ DC
2 Amp - AUX limited
OPERATING
TEMPERTURE
32° - 122°F
(0° - 50° C)
Hi-O CAN Bus
RJ45
CABLE LENGTH
= 30 ft (9 m)
- 22 AWG ● 0.65mm ● 0.33mm2
= 75 ft (23 m)
- 18 AWG ● 1.02mm ● 0.82mm2
= 328 ft (100 m)
- Category 5 K
EdgeReader and EdgePlus
82000-920 A.1
EH400, EHR40, EHRP40, EH400-K
Mounting
Junction box not included.
Wiring
RA
FT
EdgeReader and EdgePlus
CAN Termination
Resistor
(Default - IN)
Ethernet
Activity LED
3.3 VDC LED
CAN-LO (Brown)
CAN-HI (White)
GND (Black)
Hi-O Device
CAN PWR (Red)
GND
DC In
Ethernet / PoE
Auto-Detected
ATTENTION
Observe precautions for handling
ELECTROSTATIC SENSITIVE DEVICES
ES400, ER40 or ERP40 (Rear View)
INSTALLATION GUIDE
©2009 HID Global Corporation. All rights reserved.
EdgeReader and EdgePlus
82000-920 A.1
EH400, EHR40, EHRP40, EH400-K
EdgePlus - EH400-K
Strike Common
Strike N.C.
AUX N.O.
AUX Common
Strike N.O.
AUX
PWR +V
12 1 P1 4
P3
AUX N.C.
Hi-O Group Select Jumper
Short = Group 1, Open = Group 2
Outside Door
Inside Door
REX Return
REX
CAN Low
CAN High
CAN Ground
CAN V+ (12 VDC or 24 VDC)
+12V OUT
+12V GND
DATA0/DATA
DATA1/CLK
TAMPER OUT
GRN LED
RED LED
BEEPER
HOLD
NO TAMPER
READER TAMPER
TAMPER GND
RA
FT
Tamper Out
No Tamper
AC Return
AC
BATT Return
BATT
Hi-O Group Select Jumper
= Group 1, Open = Group 2
(Short
Outside Door
Inside Door
10
AUX
PWR V
P3
P10
P9
P5
P8
P6
P4
P7
Relay Jumpers
1 4 P1 1
GRP SEL
Door Return
Door
Install Edge to Backplate
©2009 HID Global Corporation. All rights reserved.
INSTALLATION GUIDE
EdgeReader and EdgePlus
82000-920 A.1
EH400, EHR40, EHRP40, EH400-K
Contact
Contact Edge through one of the following methods:
Direct Connect
If Edge will be connected to a network using static IP addressing or if the Discovery GUI is not installed on the PC, use this method.
Note: The computer must be running Windows 2000 or XP and be configured for DHCP.
1. Disconnect the computer from the network and directly connect Edge to the computer with an Ethernet cable.
2. Click Start > Run. Enter ipconfig /renew ↵
3. Access a web browser and enter 169.254.242.121 into the Address field ↵
OPIN Discovery/Update Application
RA
FT
Use the OPIN Discovery / Update Application on a computer to locate, connect and update Edge.
System Requirements: Java 6.0 or later. Go to www.java.com to download.
Operating Systems:
Windows XP and Fedora 8.
Find the OPIN Discovery / Update Application at www.ShareMethods.com > OPIN > Firmware > 2.3.x. Save the files to your local
harddrive.
The Edge must be connected to the network, and power applied, before the device is discovered.
1. With a computer connected to the same network as Edge, double-click opin-update.jar. The OPIN Discovery / Update Application
opens and the Controller Table populates.
Note: If the Controller Table does not populate, go to Edit > Broadcast Address. The default broadcast address is
255.255.255.255. Some network switches may block this transmission. If this is the case, change the subnet to match the
network, for example 10.7.255.255. Click Save.
2.
3.
4.
Select the desired device from the list.
From Path to Update Package frame, browse to the firmware location on the computer.
Click Install. Firmware is installed.
EH400 - Provides additional functionality to not only Install firmware, but to Changeover, and Rollback firmware updates. Once
firmware is installed, click Changeover to switch to the updated firmware. Click Rollback to switch back to the previoius firmware
version.
5.
View the Status Log for each status while performing Discovery and Update functions.
Configure
The web browser will prompt for login information. From the Login screen enter admin, leaving the Password field empty.
Follow the instructions on the web browser screen to configure Edge.
Hi-O Interface Modules
Hi-O interface modules are used to interface the Edge device (EdgeReader or EdgePlus) with door electronic components. Components
include access control readers, strike, magnetic lock, request to exit, door position switch, and auxillary devices.
For Hi-O interface module wiring, see their prospective Installation Guides.
Go to www.hidglobal.com > Knowledge Center > Resources > Document Library. Search the document type as a Installation Guide.
Model
Description
Part Number
EDM-M
EdgeModule Door
82342
EIM-M
EdgeModule Input
82340
EWM-M
EdgeModule Wiegand
82360
EDWM-M
EdgeModule Door & Wiegand
82363AM
ELM
EdgeModule Lock
82301
EVM
EdgeModule Voltage
82365
INSTALLATION GUIDE
©2009 HID Global Corporation. All rights reserved.
Regulatory
UL
Connect only to a Listed Access Control / Burglary power-limited power supply, or Listed Access Control / Burglary PoE (Power-over-Ethernet) adapter.
All National and local Electrical codes apply. Install in accordance with NFPA70 (NEC), Local Codes, and authorities having jurisdiction. Furthermore, install
within a Listed electrical box. All interconnected devices must be Listed.
Host-based security, Ethernet / Host Communication, has not been evaluated by UL. Ethernet port has been evaluated for supplemental use only.
The following have been evaluated as standalone products: EdgePlus model E400Cxxx and edgeReader model ERP40Cxxx.
EdgePlus was evaluated for use with all Listed HID Global Wiegand models: iCLASS, Indala Prox, HID Prox, bioCLASS, SmartID, SmartTRANS, and Mag
Stripe series (with and without keypad), up to 128-bit formats. EdgePlus was evaluated for use with all HID Global Hi-O iCLASS readers.
EdgePlus and EdgeReader are UL Listed for installation in the unprotected area, as well as within the protected area.
FCC / CANADA RADIO CERTIFICATION
CE MARKING
RA
FT
For ER40/ESR40 and ERW400 models: Reader portion (iCLASS R40 and RW400 models) certified separately.
These devices comply with part 15 of the FCC rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Le fonctionnement est soumis aux deux conditions suivantes : (1) Ce dispositif ne peut pas causer de perturbations nuisibles et (2) ce dispositif doit
accepter toute perturbation quelconque qu’il reçoit, y compris des
For all models (controller portion): FCC Class A  Canada Class A  CE Mark – Europe (EU)  C-Tick – Australia and New Zealand  VCCI – Japan
Class A Digital Devices - FCC Compliance Statement: This equipment has been tested and found to comply with the limits for a Class. A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. For regulatory compliance, all
connection wires must be bundled together.
HID Global hereby declares that these proximity readers are in compliance with the essential requirements and other relevant provisions of Directive
1999/5/EC.
The controller portion is in compliance with the essential requirements and other relevant provision of Directive 2004/108/EC.
JAPAN MIC
この装置は認証済みです。
TAIWAN DGT/NCC
經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。低功率射頻電機之使用不得
影響飛航安全及干擾合法通信；
According to «Administrative Regulations on Low Power Radio Waves Radiated Devices» Without permission granted by the DGT, any company,
enterprise, or user is not allowed to change frequency, enhance transmitting power or alter original characteristic as well as performance to a approved low
power radio-frequency devices. The low power radio-frequency devices shall not influence aircraft security and interfere legal communications; If found,
the user shall cease operating immediately until no interference is achieved. The said legal communications means radio communications is operated in
compliance with the Telecommunications Act. The low power radio-frequency devices must be susceptible with the interference from legal communications
or ISM radio wave radiated devices.
ACCESS experience.
hidglobal.com
84000-920 Rev A.1
© 2009 HID Global Corporation. All rights reserved.
Patent Pending
Check reader label for current regulatory approvals.
HID Global
North America
Asia Pacific
Europe, Middle East & Africa
15370 Barranca Parkway
Irvine, CA 92618
USA
Phone:
800 237 7769
Support: 866 607 7339
Fax:
949 732 2120
Email:
tech@hidglobal.com
19/F 625 King’s Road
NorthPoint, Island East
Hong Kong
Phone:
852 3160 9800
Support: 852 3160 9833
Fax:
852 3160 4809
Email:
asiasupport@hidglobal.com
Phoenix Road
Haverhill, Suffolk CB9 7AE
England
Phone:
+44 1440 714 850
Support: +44 1440 711 822
Fax:
+44 1440 714 840
Email:
eusupport@hidglobal.com
HID, HID Global, Edge, EdgeReader and EdgePlus are the trademarks or registered
trademarks of HID Global Corporation in the U.S. and other countries.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : Yes
Tagged PDF                      : Yes
Page Mode                       : UseOutlines
XMP Toolkit                     : Adobe XMP Core 4.0-c321 44.398116, Tue Aug 04 2009 14:24:39
Instance ID                     : uuid:44d9399a-7ad7-47cb-ad9e-052edef5d3e9
Document ID                     : adobe:docid:indd:a5ca72af-6745-11de-b499-cb0596fd70c2
Original Document ID            : adobe:docid:indd:a5ca72af-6745-11de-b499-cb0596fd70c2
Rendition Class                 : proof:pdf
Derived From Instance ID        : 9e57d0e6-6724-11de-b811-d9afd5959a6b
Derived From Document ID        : adobe:docid:indd:d5deaa3d-59d2-11de-a68d-98201af2016d
History Action                  : saved, saved, saved, saved, saved, saved, saved, saved, saved
History Instance ID             : xmp.iid:DBFE71D8D7B8DE11851ECB8B8BEC29E3, xmp.iid:DCFE71D8D7B8DE11851ECB8B8BEC29E3, xmp.iid:57DA723060D5DE11ABFF87E19C4806D0, xmp.iid:9B22685BCFD6DE118D1CB33F929FB3A4, xmp.iid:2DFA62200CDADE11BF85D318F8B6D9B4, xmp.iid:1A20DBBB1DE4DE11A13CC0160118DC16, xmp.iid:1B20DBBB1DE4DE11A13CC0160118DC16, xmp.iid:1C20DBBB1DE4DE11A13CC0160118DC16, xmp.iid:3A022922AFE5DE11AB8B888474C231C8
History When                    : 2009:10:14 10:30:18-06:00, 2009:10:14 10:30:18-06:00, 2009:11:19 16:06:37-07:00, 2009:11:21 11:54:54-07:00, 2009:11:25 14:47:28-07:00, 2009:12:08 10:44:16-07:00, 2009:12:08 10:47:59-07:00, 2009:12:08 11:16:03-07:00, 2009:12:10 14:35:03-07:00
History Software Agent          : Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0
History Changed                 : /, /metadata, /, /, /, /, /, /, /
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 299.99, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00
Manifest Placed Y Resolution    : 299.99, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches
Manifest Reference Instance ID  : uuid:42D18B5EB407DC118375ED67BF23597A, uuid:F33DCEAFA273DD11849E8931A9EDA6AC, uuid:781975661E7DDE11AE7CE05BF08A6AA3, uuid:1D8BA849FC0EDC118CE7DB8EB3C82060, xmp.iid:3A5AE16EBEE5DE11966CBD5D4537A9B1, uuid:1BBCF644A673DD11A5A29F0798D0CB96, uuid:3C064AFC8E87DE119B26E05B88681D25
Manifest Reference Document ID  : uuid:41D18B5EB407DC118375ED67BF23597A, uuid:4F34D133D472DD119F7FB81EEB5D27D9, uuid:759A32C49C4CDE11A4589C88C7D6E2C5, adobe:docid:photoshop:55c43312-5140-11da-8f26-dec6908b0933, xmp.did:3A5AE16EBEE5DE11966CBD5D4537A9B1, uuid:5434D133D472DD119F7FB81EEB5D27D9, uuid:1FFF0B3E9401DD11A2F5EAC999A6867F
Create Date                     : 2009:12:10 14:35:26-07:00
Modify Date                     : 2010:01:25 17:21:23-08:00
Metadata Date                   : 2010:01:25 17:21:23-08:00
Creator Tool                    : Adobe InDesign CS4 (6.0.4)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 8708 bytes, use -b option to extract)
Format                          : application/pdf
Title                           : EdgeReader & EdgePlus Installation Guide
Creator                         : L Hanna
Rights                          : © 2009 HID Global Corporation.  All rights reserved.
Marked                          : True
Web Statement                   : www.hidglobal.com
Startup Profile                 : Print
Doc Change Count                : 583
Producer                        : Adobe PDF Library 9.0
Trapped                         : False
Has XFA                         : No
Page Count                      : 5
Page Layout                     : SinglePage
Author                          : L Hanna

EXIF Metadata provided by EXIF.tools