HID Global MI100 Mifare 100 Series Reader User Manual 468165

HID Global Corporation Mifare 100 Series Reader 468165

Users Manual

K02013-000 Rev. A Page 1 of 5 06/08/04 Indala MIFARE Slim Reader Indala MIFARE Wallswitch Reader MI100-xxxA Installation & Operating Manual
K02013-000 Rev. A Page 2 of 5 06/08/04 FCC This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. (HID Readers and others in certain cases where shielded cable is used) For proper regulatory compliance, the drain wire should be disconnected at the power supply end of the cable. UL This Proximity Reader is intended to be powered from a limited power source output of a previously certified power supply.
K02013-000 Rev. A Page 3 of 5 06/08/04 1.0 Parts List PARTS LIST (Included) Quantity - MI100-xxxA reader with snap-on bezel and 3 meter cable. 1 - Security screw 1 - Installation manual 1 Not included parts required for installation are wire splices, linear power supply (12V, 100mA), and etc… 2.0 Mounting Instructions Mullion Mounting To mount the MI100-xxxA reader to a mullion, drill two proper size holes (for 6-32 sheet metal or thread forming screws) 3.3" apart. At center of these two holes drill a 0.375" hole for the reader cable. Route the cable through the center hole to the controller. Remove the security screw to separate the bezel from the reader to install the reader onto the mullion using two 6-32 screws. Once the reader module is screwed in place, snap on the reader bezel and re-install the security screw. Figure 1- Mullion Mounting Wall Mounting To wall mount the reader there are two choices. The first choice is to mount the reader directly to the wall. This is similar to the mullion mounting described above. The second choice is to mount it on a gang box. When installing the reader on an electrical gang box, make sure the gang box mounting holes fit the reader mounting holes. Remove the security screw to separate the bezel from the reader to install the reader to the gang box using two 6-32 screws as shown. Once the reader module is screwed in place, snap on the reader bezel and re-install the security screw. Figure 2 - Wall Mounting
K02013-000 Rev. A Page 4 of 5 06/08/04 3.0 Connecting the Reader • Connect the reader to the host controller per the wiring table below and the host installation guide. Wire Color Symbol Name/Function Red (input) V+ Positive Supply Voltage. Black (input) V- Return Power (Common) Line. Drain (input) GND Earth Ground. Foil Shield (input) GND Cable Shield. White (output) “1” Wiegand Data 1. Green (output) “0” Wiegand Data 0. Blue (input) Beeper Control Line. Brown (input) Red LED Control Line. Orange (input) Green LED Control Line. The followings are required to comply with FCC and EU RF emission standards: drain wire and foil shield can be connected either separately to earth ground and the return power (common) line respectively or all together while the earth ground and return power (common) line are tied together at the power supply. 4.0 Testing and Operation • When power is applied to the reader, the red LED is on under the default setting. • Present an ID card to the reader. The LED will momentarily turn green while the beeper beeps once, indicating that the card was read successfully. • Please note that typical read range for MIFARE (1K & 4K) cards is 1.0 – 1.5” (25-37mm). Important Product Specifications Power supply Absolute Maximum Voltage Maximum Current at 12V Operating Voltage Range Linear type 14 VDC 60mA 10.0 – 14.0 VDC Maximum cable distance to host 500 ft Wiegand Operating temperature range -30 to 65°C 5.0 Card Compatibility • The MI100-xxxA reader reads the card serial number (CSN) data from these cards: • Indala MIFARE Card, Part No. MIFxx-xxxxxxx-yyyy • Indala MIFARE/Proximity Part No. FPMIF-xxxxxx-yyyy (dual technology) • Any Philips compatible MIFARE Standard (1K & 4K) contactless smart card. • The Indala MIFARE reader will not read 125 kHz Indala Proximity cards. 6.0 Reader Operation Card Serial Number (CSN) Read Only Mode • In CSN only mode, the reader reads the 32-bit MIFARE random card serial number (CSN or UID) from any MIFARE standard (1K & 4K) card and outputs that data in a 40-bit Wiegand format: 32-bit CSN + 8 bit checksum.
K02013-000 Rev. A Page 5 of 5 06/08/04 Sector Read Only Mode • In Sector Read Only Mode the reader reads and outputs a specified number of bits from a specified sector based on a custom configuration of the reader. The following reader attributes can be configured at the factory to meet individual needs: 1. Application sector (0 – 15 or 39 depending on 1K or 4K card) 2. Application block (0-2) 3. Sector keys 4. Number of output bit (1-128) 5. Starting bit number (0-127) 6. Error-Tone on invalid card/application 7. Audio/Visual feedback (On/Off) Contacting Indala 6850 Santa Teresa Blvd. San Jose, CA 95119-1205 Main Phone: 408 361-4700 Main Fax: 408 361-4701 US Toll-Free: 800 779 8663 (Sales); 800 646 3252 (Technical Support) Web address: www.indala.com

Navigation menu