HMD global TA-1044 Smart Phone User Manual

HMD global Oy Smart Phone

User Manual

Get startedNokia 5USB micro-B USB-CXXXXXXXXXXXTA-1027/TA-1044 EN 1.0 Plug a compatible charger into a wall outlet, and connect the cable to your phone. Your phone supports the USB micro-B cable. You can also charge your phone from a computer with a USB cable, butit may take a longer time.If the battery is completely discharged, it may take several minutes before the charging indicator is displayed.To switch your phone on, press and hold the power key until the phone vibrates. The phone guides you through the setup. 1. Open the SIM tray and memory card tray by putting the provided tray opener into the holes next to the trays.2. Put the nano-SIM into the slot 1 located on the tray with the contact area face down. If you have a second SIM, put it into the slot 2. If you have a memory card, put the card into the slot located on the memory card tray.3. Slide the SIM and memory card trays back into the slots.Use only original nano-SIM cards. Use of incompatible SIM cards may damage the card or the device, and may corrupt data stored on the card. For a printable user guide, online user guide, and troubleshooting help, go to www.nokia.com/phones1. Insert the SIM and memory card2. Charge the battery and switch your phone on3. Learn more about your new NokiaFront cameraPower/Lock keyVolume keysMicrophoneMicrophoneAudio connectorCharger connectorHomeEarpieceSIM cardsMicroSD cardLoudspeakerMain camera
Product and safety infoImportant: We invite you to read the enclosed instructions before installing your equipment. For valuable information on the safe use of the device and battery, read the Product and safety info booklet before you take your device into use.You can only use your device on the GSM 850/900/1800/1900; WCDMA 1/2/4/5/8; LTE 2/3/4/7/12/17/28/38 networks. You need a subscription with a service provider.Important: 4G/LTE might not be supported by your network service provider or by the service provider you are using when traveling. In these cases, you may not be able to make or receive calls, send or receive messages or use mobile data connections. To make sure your device works seamlessly when full 4G/LTE service is not available, it is recommended that you change the highest connection speed from 4G to 3G. To do this, on the home screen, tap Settings > Mobile networks, and switch Preferred network type to 2G/3G.For more info, contact your network service provider.Maximum transmit powerGSM 900 33 dBmDCS 1800 30 dBmWCDMA FDD I 24.5 dBmWCDMA FDD VIII 24 dBmLTE Band 3 24 dBmLTE Band 7 24 dBmLTE Band 28 24 dBmLTE Band 38 24 dBmBluetooth 9 dBmWLAN 2.4 GHz 18 dBmWLAN 5 GHz 14 dBmANT+ 0 dBmNFC 2 dBmYour device has an internal, non-removable, rechargeable battery. Do not attempt to remove the battery, as you may damage the device. To replace the battery, take the device to the nearest authorised service facility. Charge your device with FC0102 charger. HMD Global may make additional battery or charger models available for this device. Third-party chargers that comply with the applicable USB requirements, and that can connect to your device USB connector, may also be compatible. Some of the accessories mentioned in this user guide, such as charger, headset, or data cable, may be sold separately.Note: The device is restricted to indoor use only when operating in the 5150 to 5350 MHz frequency range in the following countries:The surface of this device is nickel-free. Use only compatible memory cards approved for use with this device. Incompatible cards may damage the card and the device and corrupt data stored on the card. Note: Pre-installed system software and apps use a signicant part of memory space.Keep a safe distance when using the ash. Do not use the ash on people or animals at close range. Do not cover the ash while taking a photo. When this device has reached the end of its working life, all of its materials can be recovered as materials and energy. Recycle packaging and user guides at your local recycling scheme. When you cooperate and deliver all these materials to one of the available collection sites, you contribute in helping the environment and help to ensure the health of future generations.All electrical and electronic products and batteries may contain recyclable metals and other potentially hazardous substances and must be taken to their respective collection sites at the end of their working life. Under no circumstances should you break open a battery or other related materials. Do not dispose of these products as unsorted municipal waste, as this may cause contamination of the environment or risks to human health. All HMD Global products are in compliance with the applicable industry international production standards and to all requirements dened by the competent government agencies. Certication information (SAR)This mobile device meets guidelines for exposure to radio waves as set forth by the Council of Europe (CE) and the Federal Communications Commission (FCC). Refer to the following.European RF Exposure InformationYour mobile device is a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves recommended by international guidelines. These guidelines were developed by the independent scientic organization ICNIRP and include safety margins designed to assure the protection of all persons, regardless of age and health. The guidelines use a unit of measurement known as the Specic Absorption Rate, or SAR. The SAR limit for mobile devices is 2.0 W/kg and the highest SAR value for this device when tested at the ear is 0.321 W/kg*. As mobile devices oer a range of functions, they can be used in other positions, such as on the body. In this case, the highest tested SAR value is 1.55 W/kg* at the separation distance of 0.5 cm from the body. For electronic safety, maintain the separation distance with accessories containing no metal, that position handset a minimum of the above distance. Use of other accessories may not ensure compliance with RF exposure guidelines.* The tests are carried out in accordance with international guidelines for testing.FCC RF Exposure InformationYour handset is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The guidelines are based on standards that were developed by independent scientic organization through periodic and thorough evaluation of scientic studies. The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and health. The exposure standard for wireless handsets employs a unit of measurement known as the Specic Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg. The tests are performed in positions and locations (e.g. at the ear and worn on the body) as required by the FCC for each model. The highest SAR value for this model handset as reported to the FCC when tested for use at the ear is 0.8 W/kg, and when worn on the body in a holder or carry case, is 0.8 W/kg.Body-worn Operation; This device was tested for typical body-worn operations with the handset kept 1.5 cm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain a 1.5 cm separation distance between the user’s body and the handset. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided. The FCC has granted an Equipment Authorization for this model handset with all reported SAR levels evaluated as in compliance with the FCC RF emission guidelines. SAR information on this model handset is on le with the FCC and can be found under the Display Grant section of www.fcc.gov/oet/ea/ after searching on FCC ID 2AJOTTA-1027 and FCC ID 2AJOTTA-1044.Additional information on Specic Absorption Rates (SAR) can be found on the FCC website at www.fcc.gov/general/radio-frequency-safety-0.To send data or messages, a good connection to the network is needed. Sending may be delayed until such a connection is available. Follow the separation distance instructions until the sending is nished.During general use, the SAR values are usually well below the values stated above. This is because, for purposes of system eciency and to minimise interference on the network, the operating power of your mobile is automatically decreased when full power is not needed for the call. The lower the power output, the lower the SAR value.Device models may have dierent versions and more than one value. Component and design changes may occur over time and some changes could aect SAR values.For more info, go to www.sar-tick.com. Note that mobile devices may be transmitting even if you are not making a voice call.The World Health Organization (WHO) has stated that current scientic information does not indicate the need for any special precautions when using mobile devices. If you are interested in reducing your exposure, they recommend you limit your usage or use a hands-free kit to keep the device away from your head and body. For more information and explanations and discussions on RF exposure, go to the WHO website at www.who.int/peh-emf/en.This device has an electronic label for certication information. To access it, select Settings > About > Certication.Electronical information of the deviceProduct Mobile phoneSupplier HMD GlobalModel TA-1027/TA-1044Charger FC0102The following electrical characteristics apply to HMD Global FC0102 chargers only: Input 100-240 Vca 50-60 Hz 0-300 mAOutput 5.0 Vcc 0-2000 mA Rechargeable battery supplier HMD GlobalPhone power consumption 3,8 VccCopyrights and other noticesDeclaration of Conformity Hereby, HMD Global Oy declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. A copy of the Declaration of Conformity can be found at www.nokia.com/mobile-declaration-of-conformity.FCC notice:This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For more info, go to www.fcc.gov/engineering-technology/electromagnetic-compatibility-division/radio-frequency-safety/faq/rf-safety. Any changes or modications not expressly approved by HMD Global could void the user’s authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.© 2017 HMD Global. All rights reserved. HMD Global Oy is the exclusive licensee of the Nokia brand for phones & tablets. Nokia is a registered trademark of Nokia Corporation.Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other countries, used with permission.Manufactured in China. Importer (this information applies only in Mexico):Grand cel S.A. de C.V.106 Avenida Calle CoronaColonia Cervecería CoronaNaucalpanEdo de MéxicoCP 53330RFC: GCE1410146Y9

Navigation menu