HON HAI PRECISION IND 74487504 802.11 b/g/n MiniPCI module User Manual Manual Part1

Download:
Mirror Download [FCC.gov]
Document ID	902083
Application ID	gJW9ZwhWSKG8VGjK5bxeew==
Document Description	Manual Part1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	202.86kB (2535803 bits)
Date Submitted	2008-02-14 00:00:00
Date Available	2008-05-14 00:00:00
Creation Date	2008-02-14 16:09:15
Producing Software	Acrobat Distiller 7.0.5 (Windows)
Document Lastmod	2008-02-14 18:07:11
Document Title	CB-82/MB-82/EC-82/MC-82 WLAN Client Cards User Guide
Document Creator	FrameMaker 7.0
Document Author:	Marvell

Cover
74-4875-04
CB-82/MB-82/EC-82/MC-82
WLAN Client Cards
User Guide
Cisco
Marvell. Moving Forward Faster
Doc. No. MV-S800473-00, Rev. B
August 14, 2007
CONFIDENTIAL
Document Classification: Proprietary Information
CB-82/MB-82/EC-82/MC-82
User Guide
Document Conventions
Note: Provides related information or information of special importance.
Caution: Indicates potential damage to hardware or software, or loss of data.
Warning: Indicates a risk of personal injury.
Document Status
Doc Status: 2.00
Technical Publication: 0.x
For more information, visit our website at: www.marvell.com
Disclaimer
No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, for any purpose,
without the express written permission of Marvell. Marvell retains the right to make changes to this document at any time, without notice. Marvell makes no warranty of any
kind, expressed or implied, with regard to any information contained in this document, including, but not limited to, the implied warranties of merchantability or fitness for any
particular purpose. Further, Marvell does not warrant the accuracy or completeness of the information, text, graphics, or other items contained within this document.
Marvell products are not designed for use in life-support equipment or applications that would cause a life-threatening situation if any such products failed. Do not use
Marvell products in these types of equipment or applications.
With respect to the products described herein, the user or recipient, in the absence of appropriate U.S. government authorization, agrees:
1) Not to re-export or release any such information consisting of technology, software or source code controlled for national security reasons by the U.S. Export Control
Regulations ("EAR"), to a national of EAR Country Groups D:1 or E:2;
2) Not to export the direct product of such technology or such software, to EAR Country Groups D:1 or E:2, if such technology or software and direct products thereof are
controlled for national security reasons by the EAR; and,
3) In the case of technology controlled for national security reasons under the EAR where the direct product of the technology is a complete plant or component of a plant,
not to export to EAR Country Groups D:1 or E:2 the direct product of the plant or major component thereof, if such direct product is controlled for national security reasons
by the EAR, or is subject to controls under the U.S. Munitions List ("USML").
At all times hereunder, the recipient of any such information agrees that they shall be deemed to have manually signed this document in connection with their receipt of any
such information.
Copyright © 2007. Marvell International Ltd. All rights reserved. Marvell, the Marvell logo, Moving Forward Faster, Alaska, Fastwriter, Datacom Systems on Silicon, Libertas,
Link Street, NetGX, PHYAdvantage, Prestera, Raising The Technology Bar, The Technology Within, Virtual Cable Tester, and Yukon are registered trademarks of Marvell.
Ants, AnyVoltage, Discovery, DSP Switcher, Feroceon, GalNet, GalTis, Horizon, Marvell Makes It All Possible, RADLAN, UniMAC, and VCT are trademarks of Marvell. All
other trademarks are the property of their respective owners.
Doc. No. MV-S800473-00 Rev. B
Page 2
CONFIDENTIAL
Document Classification: Proprietary Information
Copyright © 2007 Marvell
August 14, 2007, 2.00
Table of Contents
Table of Contents
Table of Contents ....................................................................................................................................... 3
List of Figures............................................................................................................................................. 5
List of Tables .............................................................................................................................................. 7
Introduction.................................................................................................................................... 9
1.1
Overview ...........................................................................................................................................................9
1.2
Wireless Networks ............................................................................................................................................9
1.2.1
Ad-Hoc Mode ......................................................................................................................................9
1.2.2
Infrastructure Mode.............................................................................................................................9
Marvell Wireless Configuration Utility Overview ...................................................................... 11
2.1
Overview .........................................................................................................................................................11
2.2
Marvell Wireless Configuration Utility..............................................................................................................11
2.2.1
Windows XP and Windows Server 2003 Users ................................................................................11
2.2.2
Tray Status Icons ..............................................................................................................................12
2.3
Security ...........................................................................................................................................................13
Marvell Wireless Configuration Utility User Interface .............................................................. 15
3.1
Network Status Tab.........................................................................................................................................16
3.1.1
Select Profile.....................................................................................................................................16
3.1.2
Link Information ................................................................................................................................17
3.1.3
Signal Strength / Wireless Mode Indicator........................................................................................18
3.1.4
Internet Protocol (TCP/IP) ................................................................................................................18
3.1.5
Actual Throughput Performance .......................................................................................................19
3.1.6
Radio On/Off Check Box ..................................................................................................................19
3.2
Profile Manager Tab........................................................................................................................................21
3.2.1
Profile Setting—Network Info Tab ....................................................................................................22
3.2.2
Profile Setting—Security Tab............................................................................................................24
3.2.3
Legacy Authentication Modes...........................................................................................................25
3.2.3.1 Open System / Shared Key / Auto Switch ..........................................................................26
3.2.3.2 WPA-PSK / WPA2-PSK .....................................................................................................28
3.2.4
802.1X Authentication Modes...........................................................................................................29
3.2.4.1 802.1X / WPA / WPA2 with EAP/TLS.................................................................................29
3.2.4.2 802.1X / WPA / WPA2 with PEAP......................................................................................36
3.2.4.3 802.1X / WPA / WPA2 with EAP/TTLS...............................................................................41
3.2.4.4 802.1X / WPA / WPA2 with LEAP ......................................................................................46
3.2.4.5 802.1X / WPA / WPA2 with EAP-FAST..............................................................................49
3.2.5
Profile Setting—Protocol Tab ...........................................................................................................52
Copyright © 2007 Marvell
August 14, 2007, 2.00
CONFIDENTIAL
Document Classification: Proprietary Information
Doc. No. MV-S800473-00 Rev. B
Page 3
CB-82/MB-82/EC-82/MC-82
User Guide
3.3
Site Survey Tab...............................................................................................................................................53
3.3.1
Site Survey—Networks Filter ............................................................................................................53
3.3.2
Site Survey—List of Detected Stations .............................................................................................54
3.3.3
Site Survey—Filter Button ................................................................................................................55
3.3.3.1 Network SSID .....................................................................................................................55
3.3.3.2 Network BSSID ..................................................................................................................55
3.3.3.3 Select Channel ...................................................................................................................55
3.3.4
Site Survey—Refresh Button ............................................................................................................55
3.3.5
Site Survey—Associate Button .........................................................................................................55
3.4
Statistics Tab...................................................................................................................................................56
3.4.1
Signal Strength .................................................................................................................................56
3.4.2
Transmit Section ...............................................................................................................................57
3.4.3
Receive Section ................................................................................................................................58
3.4.4
Protocol Section................................................................................................................................58
3.5
Advanced Tab .................................................................................................................................................59
3.5.1
Advanced Tab—Marvell Wireless Card ............................................................................................59
3.5.2
Advanced Tab—Miscellaneous ........................................................................................................60
3.6
AutoLink Tab ...................................................................................................................................................60
3.7
Admin Tab .......................................................................................................................................................63
3.7.1
Admin Tab—Import Profiles..............................................................................................................63
3.7.2
Admin Tab—Export Profiles .............................................................................................................63
3.7.3
Admin Tab—Autostart Marvell Wireless Configuration Utility ...........................................................64
3.7.4
Admin Tab—Stop Windows Wireless Zero Configuration Service ...................................................64
3.8
About Tab........................................................................................................................................................64
Compliance Statements .............................................................................................................. 65
A.1
Federal Communications Commission (FCC) Compliance.............................................................................65
A.2
Industry Canada Notice...................................................................................................................................65
A.3
Europe—EU Declaration of Conformity and Restrictions................................................................................66
A.4
Taiwan DGT ....................................................................................................................................................67
Acronyms and Abbreviations..................................................................................................... 69
Revision History .......................................................................................................................... 71
Doc. No. MV-S800473-00 Rev. B
Page 4
CONFIDENTIAL
Document Classification: Proprietary Information
Copyright © 2007 Marvell
August 14, 2007, 2.00
List of Figures
List of Figures
Introduction........................................................................................................................................ 9
Marvell Wireless Configuration Utility Overview .......................................................................... 11
Figure 1:
Marvell Wireless Configuration Utility Icon........................................................................................11
Figure 2:
Admin Tab—Stop Windows Wireless Zero Configuration Service ...................................................12
Figure 3:
Tray Status Icons Window ................................................................................................................12
Marvell Wireless Configuration Utility User Interface .................................................................. 15
Figure 4:
Network Status Tab ..........................................................................................................................16
Figure 5:
Select Profile Section........................................................................................................................16
Figure 6:
Link Information Section ...................................................................................................................17
Figure 7:
Signal Strength Bar...........................................................................................................................18
Figure 8:
Internet Protocol Section ..................................................................................................................18
Figure 9:
Actual Throughput Performance Section ..........................................................................................19
Figure 10:
Radio On/Off Check Box ..................................................................................................................19
Figure 11:
Radio On/Off in the System Tray ......................................................................................................20
Figure 12:
Profile Manager Tab .........................................................................................................................21
Figure 13:
Network Info Tab (Infrastructure Network)........................................................................................22
Figure 14:
Network Info Tab (Ad-Hoc Network) .................................................................................................23
Figure 15:
Security Tab—Authentication Modes ...............................................................................................24
Figure 16:
Security Tab—Open System with WEP............................................................................................26
Figure 17:
WEP Key Configuration Window ......................................................................................................26
Figure 18:
WEP Key Setting ..............................................................................................................................27
Figure 19:
Security Tab—WPA2-PSK with TKIP ...............................................................................................28
Figure 20:
Security Tab—WPA2 with EAP/TLS (Use Certificate) ......................................................................29
Figure 21:
EAP/TLS (Use Certificate) Configuration Window—Client Authentication Tab ................................30
Figure 22:
Select Certificate Window (Client Certificates) .................................................................................31
Figure 23:
EAP/TLS Configuration Window—Server Authentication Tab ..........................................................32
Figure 24:
Select Certificate Window (Server Certificates) ................................................................................33
Figure 25:
Server Authentication—Trusted Domain or Server...........................................................................34
Figure 26:
Security Tab—WPA2 with PEAP ......................................................................................................36
Figure 27:
PEAP Configuration Window—Client Authentication Tab ................................................................37
Figure 28:
PEAP Configuration Window—Server Authentication Tab ...............................................................38
Figure 29:
Select Certificate Window (Server Certificates) ................................................................................39
Figure 30:
Server Authentication—Trusted Domain or Server...........................................................................40
Figure 31:
Security Tab—WPA2 with EAP/TTLS...............................................................................................41
Figure 32:
EAP/TTLS Configuration Window—Client Authentication Tab .........................................................42
Figure 33:
EAP/TTLS Configuration Window—Server Authentication Tab........................................................43
Figure 34:
Select Certificate Window (Server Certificates) ................................................................................44
Figure 35:
Server Authentication—Trusted Domain or Server...........................................................................45
Copyright © 2007 Marvell
August 14, 2007, 2.00
CONFIDENTIAL
Document Classification: Proprietary Information
Doc. No. MV-S800473-00 Rev. B
Page 5
CB-82/MB-82/EC-82/MC-82
User Guide
Figure 36:
Security Tab—WPA2 with LEAP ......................................................................................................46
Figure 37:
LEAP Configuration Window ............................................................................................................47
Figure 38:
Security Tab—WPA2 with EAP-FAST ..............................................................................................49
Figure 39:
EAP-FAST Configuration Window ....................................................................................................50
Figure 40:
Protocol Tab .....................................................................................................................................52
Figure 41:
Site Survey Tab ................................................................................................................................53
Figure 42:
Site Survey—List of Detected Stations .............................................................................................54
Figure 43:
Site Survey—Advanced Filter Window .............................................................................................55
Figure 44:
Statistics Tab ....................................................................................................................................56
Figure 45:
Transmit Section ...............................................................................................................................57
Figure 46:
Receive Section ................................................................................................................................58
Figure 47:
Protocol Section................................................................................................................................58
Figure 48:
Advanced Tab...................................................................................................................................59
Figure 49:
Miscellaneous Section ......................................................................................................................60
Figure 50:
Access Point AutoLink Button...........................................................................................................60
Figure 51:
AutoLink Tab.....................................................................................................................................61
Figure 52:
AutoLink Tab (AutoLink Complete) ...................................................................................................62
Figure 53:
Admin Tab ........................................................................................................................................63
Figure 54:
About Tab .........................................................................................................................................64
Compliance Statements ................................................................................................................... 65
Acronyms and Abbreviations .......................................................................................................... 69
Revision History ............................................................................................................................... 71
Doc. No. MV-S800473-00 Rev. B
Page 6
CONFIDENTIAL
Document Classification: Proprietary Information
Copyright © 2007 Marvell
August 14, 2007, 2.00
CB-82/MB-82/EC-82/MC-82
User Guide
List of Tables
Introduction......................................................................................................................................... 9
Marvell Wireless Configuration Utility Overview ........................................................................... 11
Marvell Wireless Configuration Utility User Interface ................................................................... 15
Table 1:
Link Information Section Description ................................................................................................17
Table 2:
Internet Protocol Section Description ...............................................................................................19
Table 3:
Profile List Section Description .........................................................................................................21
Table 4:
Network Info Tab Description ...........................................................................................................23
Table 5:
WEP Key Configuration Window Description ...................................................................................27
Table 6:
EAP/TLS Configuration Window Description—Client Authentication Tab ........................................34
Table 7:
Select Certificate Window Description (Client Certificates) ..............................................................34
Table 8:
EAP/TLS Configuration Window Description—Server Authentication Tab .......................................35
Table 9:
Select Certificate Window Description (Server Certificates) .............................................................35
Table 10:
PEAP Configuration Window Description—Client Authentication Tab .............................................40
Table 11:
PEAP Configuration Window Description—Server Authentication Tab ............................................40
Table 12:
Select Certificate Window Description (Server Certificates) .............................................................41
Table 13:
EAP/TTLS Configuration Window Description—Client Authentication Tab ......................................45
Table 14:
Table 15:
EAP/TTLS Configuration Window Description—Server Authentication Tab.....................................45
THIS PAGE INTENTIONALLY LEFT BLANK
Select Certificate Window Description (Server Certificates) .............................................................46
Table 16:
LEAP Configuration Window Description .........................................................................................48
Table 17:
EAP-FAST Configuration Window Description .................................................................................51
Table 18:
Protocol Tab Description ..................................................................................................................52
Table 19:
List of Detected Stations Description ................................................................................................54
Table 20:
Transmit Section Description ............................................................................................................57
Table 21:
Receive Section Description .............................................................................................................58
Table 22:
Protocol Section Description.............................................................................................................59
Table 23:
Advanced Tab Miscellaneous Section Description ...........................................................................60
Compliance Statements ................................................................................................................... 65
Acronyms and Abbreviations .......................................................................................................... 69
Table 24:
Acronyms and Abbreviations ............................................................................................................69
Revision History ............................................................................................................................... 71
Table 25:
Revision History ................................................................................................................................71
Doc. No. MV-S800473-00 Rev. B
Page 7
CONFIDENTIAL
Document Classification: Proprietary Information
Copyright © 2007 Marvell
August 14, 2007, 2.00
CB-82/MB-82/EC-82/MC-82
User Guide
THIS PAGE INTENTIONALLY LEFT BLANK
Doc. No. MV-S800473-00 Rev. B
Page 8
CONFIDENTIAL
Document Classification: Proprietary Information
Copyright © 2007 Marvell
August 14, 2007, 2.00
Introduction
Overview
Introduction
1.1
Overview
This document describes the functions of the Marvell Wireless Client Card Configuration Utility for
the following Marvell® IEEE 802.11g/b and draft-802.11n WLAN client cards:
„
Marvell CB-82 CardBus WLAN Client Card
„
Marvell MB-82 Mini PCI WLAN Client Card
„
Marvell EC-82 PCI Express WLAN Client Card
„
Marvell MC-82 PCI Express WLAN Client Mini Card
Marvell high throughput client cards are both IEEE 802.11g/b and draft-802.11n compliant.
„
Note
1.2
„
For information on installing the Marvell Wireless Configuration Utility, the Marvell
client card, and the Marvell Windows driver, see the CB-82/MB-82/EC-82/MC-82
Installation Guide.
For a list of acronyms used throughout this document see Appendix B, Acronyms
and Abbreviations, on page 69.
Wireless Networks
The Marvell client cards operate similar to Ethernet cards, except that a radio replaces the wires
between communication devices. All existing applications that operate over Ethernet operate over a
Marvell wireless network without any modification or need for special wireless networking software.
The Marvell client cards support the following network technologies:
„
„
1.2.1
Ad-Hoc (peer-to-peer group) mode
Access Point (AP) Infrastructure mode
Ad-Hoc Mode
In Ad-Hoc mode (also referred to as peer-to-peer mode), wireless clients send and receive
information to other wireless clients without using an AP. In comparison to Infrastructure mode, this
type of WLAN connection only contains wireless clients. Ad-Hoc mode is useful for establishing a
network where wireless infrastructure does not exist or where services are not required. Two or
more computers can establish an Ad-Hoc network when within range of one another.
Ad-Hoc mode is used to connect network computers at home or in small offices. It can also be used
to set up a temporary wireless network for meetings.
1.2.2
Infrastructure Mode
In Infrastructure mode, wireless devices communicate with other wireless devices or devices on the
LAN side wired network through APs. When communicating through wired networks, client cards
send and receive information through APs.
Access Points are typically strategically located within an area to provide optimal coverage for
wireless clients. A large WLAN uses multiple APs to provide coverage over a wide area. APs
connect to a LAN through a wired Ethernet connection. APs send and receive information from the
LAN through this wired connection. Most corporate WLANs operate in Infrastructure mode because
they require access to the wired LAN in order to use services such as file servers or printers.
Copyright © 2007 Marvell
August 14, 2007, 2.00
CONFIDENTIAL
Document Classification: Proprietary Information
Doc. No. MV-S800473-00 Rev. B
Page 9
CB-82/MB-82/EC-82/MC-82
User Guide
THIS PAGE INTENTIONALLY LEFT BLANK
Doc. No. MV-S800473-00 Rev. B
Page 10
CONFIDENTIAL
Document Classification: Proprietary Information
Copyright © 2007 Marvell
August 14, 2007, 2.00
Marvell Wireless Configuration Utility Overview
Overview
Marvell Wireless Configuration Utility
Overview
2.1
Overview
The Marvell Wireless Client Card Configuration Utility is a Windows® based application that allows
configuration and management of the Marvell high throughput client cards. The Marvell Wireless
Configuration Utility sets up profiles and performs other wireless network management tasks. For
information on installing the Marvell Wireless Configuration Utility see the Installation Guide.
2.2
Marvell Wireless Configuration Utility
Once installed, the Marvell Wireless Configuration Utility is accessed from the Start menu or from
the Desktop.
Start menu:
Start > Marvell Wireless Configuration Utility
„
Start > Programs > Marvell > Marvell Wireless Configuration Utility
„
Desktop:
Double-click the Marvell Wireless Configuration Utility icon.
„
Figure 1: Marvell Wireless Configuration Utility Icon
2.2.1
Windows XP and Windows Server 2003 Users
For Windows XP and Windows Server 2003, either the Windows Wireless Zero Configuration
Service or the Marvell Wireless Configuration Utility can be used to configure the Marvell client card.
For further information on the Windows Wireless Configuration Service, refer to the Windows
documentation.
Note
When using the Marvell Wireless Configuration Utility, Marvell recommends turning off
the Windows Wireless Zero Configuration Service, which is enabled by default. Both
utilities should not be used at the same time.
Disabling Windows Wireless Zero Configuration Service
To disable the Windows Wireless Zero Configuration Service:
1.
2.
Copyright © 2007 Marvell
August 14, 2007, 2.00
Start the Marvell Wireless Configuration Utility.
Click the Admin tab.
CONFIDENTIAL
Document Classification: Proprietary Information
Doc. No. MV-S800473-00 Rev. B
Page 11
CB-82/MB-82/EC-82/MC-82
User Guide
3.
Select the Stop Windows Wireless Zero Configuration Service check box.
Figure 2: Admin Tab—Stop Windows Wireless Zero Configuration Service
2.2.2
Tray Status Icons
Different icons in the system tray indicate the status of the wireless connection.
Figure 3: Tray Status Icons Window
Card Unplugged
(red with “X” mark)
Not Connected
(red)
Connected
(green)
Doc. No. MV-S800473-00 Rev. B
Page 12
CONFIDENTIAL
Document Classification: Proprietary Information
Copyright © 2007 Marvell
August 14, 2007, 2.00
Marvell Wireless Configuration Utility Overview
Security
2.3
Security
Implementing a security infrastructure to monitor physical access to WLAN networks is more difficult
than monitoring access on wired networks. Unlike wired networks where a physical connection is
required, anyone within the range of a wireless AP can send and receive frames, as well as listen for
frames being sent.
IEEE 802.11 and IEEE 802.1X define a set of standards and protocols for use in minimizing the
security risks on wireless networks. These include the authentication modes used to authenticate
the wireless client station and the wireless AP to be connected, complemented by different
encryption methods used for data to be transmitted over the wireless network. Four of these security
standards are as follows:
„
802.1X—802.1X authentication provides authenticated access to 802.11 wireless networks and
to wired Ethernet networks. 802.1X minimizes wireless network security risks by providing user
and computer identification, centralized authentication, and encryption services based on the
Wired Equivalent Privacy (WEP) algorithm. 802.1X supports the Extensible Authentication
Protocol (EAP). EAP allows the use of different authentication methods, such as smart cards
and certificates.
„
Wired Equivalent Privacy (WEP)—WEP is a basic security implementation according to the
IEEE 802.11 standard. Due to various security issues WEP encryption is vulnerable and was
therefore superseded by WPA and WPA2 encryption.
„
Wi-Fi Protected Access (WPA)—WPA is a security implementation based on a subset of the
802.11i standard. WPA provides enhanced security for wireless networks when used with the
Temporal Key Integrity Protocol (TKIP) and the Message Integrity Check (MIC) algorithms.
„
Wi-Fi Protected Access 2 (WPA2)—WPA2 is the next generation Wi-Fi security, based on the
final 802.11i standard. WPA2 offers the strongest available security in the form of Advanced
Encryption Standard (AES) level encryption, plus faster roaming between APs.
Security Configurations
The Marvell Wireless Configuration Utility supports the following security features:
„
Authentication Modes
•
•
•
•
•
•
•
Open System
Shared Key
Auto Switch
WPA-PSK
WPA2-PSK
WPA
WPA2
• 802.1X Authentication Protocol (including support for Cisco® Compatible Extensions (CCX))
„
- EAP/Transport Layer Security (EAP/TLS) (equivalent to Microsoft “Smart Card or other
Certificate”)
- Protected EAP (PEAP)
- EAP/Tunneled TLS Authentication Protocol (EAP/TTLS)
- Light EAP (LEAP)
- EAP-Flexible Authentication via Secure Tunneling (EAP-FAST)
Encryption Methods
• Security Off
• WEP (including support for Cisco Message Integrity Check (CMIC) and Cisco Key Integrity
Protocol (CKIP))
Copyright © 2007 Marvell
August 14, 2007, 2.00
CONFIDENTIAL
Document Classification: Proprietary Information
Doc. No. MV-S800473-00 Rev. B
Page 13
CB-82/MB-82/EC-82/MC-82
User Guide
• TKIP (WPA, WPA-PSK)
• AES (WPA2, WPA2-PSK)
„
WEP Key Size
• 40-bit key (64-bit WEP)
• 104-bit key (128-bit WEP)
Doc. No. MV-S800473-00 Rev. B
Page 14
CONFIDENTIAL
Document Classification: Proprietary Information
Copyright © 2007 Marvell
August 14, 2007, 2.00
Marvell Wireless Configuration Utility User Interface
Marvell Wireless Configuration Utility
User Interface
The Marvell Wireless Client Card Configuration Utility allows configuration of Marvell high
throughput client cards through the following tabs:
„
Network Status—displays the status of the network to which the user is connected. The
Marvell Wireless Configuration Utility initializes on this page.
„
Profile Manager—displays the current profiles and allows the user to set attributes for network
type, security options and protocols, as well as create/modify/delete profiles.
„
Site Survey—displays site survey information.
„
Statistics—displays the statistics of the current session.
„
Advanced—used to set protocol parameters.
„
AutoLink—to set AutoLink connection
„
Admin—used to import and export profiles. Additionally, the user can define how to use the
Marvell Wireless Configuration Utility and the Windows Wireless Zero Configuration Service.
„
About—provides information such as the driver version number, firmware version number,
Marvell Wireless Configuration Utility version number, and Medium Access Controller (MAC)
address of the client card.
Copyright © 2007 Marvell
August 14, 2007, 2.00
CONFIDENTIAL
Document Classification: Proprietary Information
Doc. No. MV-S800473-00 Rev. B
Page 15
CB-82/MB-82/EC-82/MC-82
User Guide
3.1
Network Status Tab
The Network Status tab displays the status of the network. When the Marvell Wireless
Configuration Utility initializes, it displays the Network Status tab.
Figure 4: Network Status Tab
3.1.1
Select Profile
The Select Profile section displays the name of the profile in use. Additional information about the
profile is provided in the Profile Manager.
Select one of the profiles previously defined by clicking the down arrow and highlighting a profile
from the pull-down list.
Figure 5: Select Profile Section
Profiles are created, modified, and deleted through the Profile Manager.
Doc. No. MV-S800473-00 Rev. B
Page 16
CONFIDENTIAL
Document Classification: Proprietary Information
Copyright © 2007 Marvell
August 14, 2007, 2.00
Marvell Wireless Configuration Utility User Interface
Network Status Tab
3.1.2
Link Information
The Link Information section contains the current information about the wireless connection.
Figure 6: Link Information Section
Table 1:
F ie l d
Description
Status
Status of the wireless network connection:
• Card Unplugged
Client card is not plugged in, or client card is plugged in but not recognized.
• Connected
Client card is plugged in and connected to a wireless network.
• No Connection
Client card is plugged in, but no wireless connection.
• No Radio
Client card is plugged in, but the radio is turned off. To turn the radio on, clear
the Radio Off check box.
• Scanning for
Scanning for available APs and wireless stations in the area.
• Waiting for peer
Waiting for a peer station to connect to the wireless network (Ad-Hoc network
only).
Network SSID
Network SSID label (i.e., Network Name). The Network Name is a text string of up
to 32 characters.
Network Type
Type of environment connected to:
• Infrastructure Mode
In this mode, wireless clients send and receive information through APs. The
APs are strategically located within an area to provide optimal coverage for
wireless clients. A large WLAN uses multiple APs to provide coverage over a
wide area. APs can connect to a LAN through a wired Ethernet connection. APs
send and receive information from the LAN through the wired connection.
• Ad-Hoc Mode
In this mode, wireless clients send and receive information to other wireless
clients without using an AP. This type of WLAN only contains wireless clients.
Use Ad-Hoc mode to connect network computers at home or in small office, or
to set up a temporary wireless network for a meeting.
Network BSSID
Network Basic Service Set (BSS) Identifier. The BSSID is a 48-bit identity used to
identify a particular BSS within an area. In Infrastructure BSS networks, the BSSID
is the MAC address of the AP. In Ad-Hoc networks, the BSSID is generated
randomly.
Copyright © 2007 Marvell
August 14, 2007, 2.00
Link Information Section Description
CONFIDENTIAL
Document Classification: Proprietary Information
Doc. No. MV-S800473-00 Rev. B
Page 17
CB-82/MB-82/EC-82/MC-82
User Guide
Table 1:
3.1.3
Link Information Section Description (Continued)
F ie l d
Description
Security
Reports the type and level of security set. The security level is set through the
Profile Setting of the Profile Manager tab. Configure security settings also
through the Site Survey tab when connecting to a network.
Tx/Rx Rates
Current Tx Rate and Rx Rate of the channel being monitored.
Signal Strength / Wireless Mode Indicator
The color-coded Signal Strength bar displays the signal strength of the last packet received by the
client card.
Figure 7: Signal Strength Bar
g means connected to an 802.11g capable AP
b means connected to an 802.11b capable AP
Signal strength is reported as a percentage. A signal in the red indicates a bad connection. A signal
in the green indicates a good connection.
The Wireless Mode indicator shows the data rates the client card operates. There are two modes:
„
802.11b
„
802.11g (backward compatible to 802.11b)
3.1.4
Internet Protocol (TCP/IP)
This section specifies the IP configuration of the client station when it is connected.
Figure 8: Internet Protocol Section
Doc. No. MV-S800473-00 Rev. B
Page 18
CONFIDENTIAL
Document Classification: Proprietary Information
Copyright © 2007 Marvell
August 14, 2007, 2.00
Marvell Wireless Configuration Utility User Interface
Network Status Tab
Table 2:
3.1.5
Internet Protocol Section Description
F ie l d
Description
DHCP Option
Dynamic Host Configuration Protocol. Either enabled or disabled.
IP Address
An identifier for a computer or device on a TCP/IP network. The format of
an IP address is a 32-bit numeric address written as four numbers
separated by periods. Each number can be 0 to 255.
Subnet Mask
A mask used to determine what subnet an IP address belongs to. An IP
address has two components, the network part and the host part. The
subnet mask specifies the network part of the IP address.
Default Gateway
The default node on a network that serves as an entrance to another
network. In enterprises, the gateway is the computer that routes the traffic
from a workstation to the outside network that is serving the Web pages.
In homes, the gateway is the Internet Service Provider (ISP) that connects
the user to the Internet.
Actual Throughput Performance
This section of the Network Status tab displays the Current Tx Rate and the Current Rx Rate of the
channel being monitored.
Figure 9: Actual Throughput Performance Section
3.1.6
Radio On/Off Check Box
Note
These are actual throughput diagrams (without the WLAN overhead delivered by the
client card).
Selecting the Radio Off check box turns off the radio. Clearing the check box turns on the radio.
Figure 10: Radio On/Off Check Box
Copyright © 2007 Marvell
August 14, 2007, 2.00
CONFIDENTIAL
Document Classification: Proprietary Information
Doc. No. MV-S800473-00 Rev. B
Page 19
CB-82/MB-82/EC-82/MC-82
User Guide
Another way to turn the radio on or off is to right-click the Configuration Utility icon in System Tray
and select Turn Radio Off to turn the radio off. When the radio is off, select Turn Radio On to turn
the radio back on.
Figure 11: Radio On/Off in the System Tray
The system hot key Alt+F2 can also be used to turn the radio on/off.
When the radio is off, there is no radio activity, and the following tabs are disabled:
„
Profile Manager
„
Site Survey
„
Statistics
„
Advanced
„
AutoLink
Doc. No. MV-S800473-00 Rev. B
Page 20
CONFIDENTIAL
Document Classification: Proprietary Information
Copyright © 2007 Marvell
August 14, 2007, 2.00
Marvell Wireless Configuration Utility User Interface
Profile Manager Tab
3.2
Profile Manager Tab
The Profile Manager tab displays the profiles available and allows you to create, modify, and delete
profiles.
Figure 12: Profile Manager Tab
Profile Manager—Profile List
The section on the left side of this tab lists all of the profiles available. Highlighting a profile selects it.
If the check box next to the profile is selected, that profile is used in auto-configuration mode when
the link is lost. If it is not selected, that profile is excluded in auto-configuration. The buttons
associated with this window are as follows.
Table 3:
Button
Description
Apply Profile
Applies the profile selected.
Apply the profile by double-clicking the desired profile.
Move Up/Down
Moves the profile up and down in the list.
All profiles with the Network Type set to Infrastructure are displayed before the
profiles with the Network Type set to Ad-Hoc. In auto-configuration mode, the
selected profiles at the top of the list have higher priority than selected profiles at
the bottom of the list.
Copyright © 2007 Marvell
August 14, 2007, 2.00
Profile List Section Description
CONFIDENTIAL
Document Classification: Proprietary Information
Doc. No. MV-S800473-00 Rev. B
Page 21
CB-82/MB-82/EC-82/MC-82
User Guide
Table 3:
Profile List Section Description (Continued)
Button
Description
Delete
Deletes a profile.
Create
Creates a profile.
Save
Saves changes made to a selected profile.
Profile Manager—Profile Setting
The Profile Settings are used to set, modify, and display information about the profile selected in the
Profile List section. The information is divided into three tabs:
„
Network Info
„
Security
„
Protocol
3.2.1
Profile Setting—Network Info Tab
The Profile Manager initially displays the Network Info tab.
Figure 13: Network Info Tab (Infrastructure Network)
Doc. No. MV-S800473-00 Rev. B
Page 22
CONFIDENTIAL
Document Classification: Proprietary Information
Copyright © 2007 Marvell
August 14, 2007, 2.00
Marvell Wireless Configuration Utility User Interface
Profile Manager Tab
Figure 14: Network Info Tab (Ad-Hoc Network)
Note to US model owner: To comply with US FCC regulation, the country selection function has
been completely removed from all US models. The above function is for non-US models only.
The Network Info tab fields are as follows.
Table 4:
Network Info Tab Description
F ie l d
Description
Profile Name
Name of profile selected
Network SSID
Network SSID label
Network Type
•
•
Wireless Mode
•
•
•
•
•
Auto
Connects to either an 802.11g network or to an 802.11b network
802.11g
Connects either to an 802.11g network or to an 802.11b network
802.11b
Connects to an 802.11b network only
802.11n (2.4 GHz)
Connects to an 802.11n network with 2.4 GHz
802.11n (5 GHz)
Connects to an 802.11n network with 5 GHz
Preferred Channel
Channel being used for an Ad-Hoc network initiated by the client card
The channel can be selected only at creation of a new profile (Ad-Hoc
network only).
Region Code
Sets the region code
Available options are Default, USA (FCC), Canada (IC), Europe (ETSI),
Spain, France, Japan (MKK), Taiwan (DGT), and Australia/Korea
Copyright © 2007 Marvell
August 14, 2007, 2.00
Infrastructure
Connects to an existing Infrastructure network
Ad-Hoc
Either connects to an existing Ad-Hoc network or initiates a new
Ad-Hoc network
CONFIDENTIAL
Document Classification: Proprietary Information
Doc. No. MV-S800473-00 Rev. B
Page 23
CB-82/MB-82/EC-82/MC-82
User Guide
Table 4:
F ie l d
Description
802.11n Network
Enables/disables draft-802.11n functionality
If enabled, the Modulation and Coding Scheme (MCS) index and 802.11n
options can be configured.
Channel Width
Sets the channel bandwidth
Available options are Auto, 20 MHz, and 40 MHz. The default is Auto.
Guard Interval
Sets the Guard Interval
Available options are Auto, Standard, and Short. The default is Auto.
Extension Channel
Sets the extension channel mode when bandwidth is 40 MHz
Available options are Auto, None, Lower, and Upper. The default is Auto.
Antenna Selection
Sets the antenna selections
Available options are Auto, Antenna A, Antenna B, 2 by 2, and 2 by 3.
The default is Auto.
Note
3.2.2
Network Info Tab Description (Continued)
The fields Wireless Mode and Preferred Channel are used only when a new Ad-Hoc
network is initiated by the client card. These two attributes are ignored when the client
card is connected to an existing Ad-Hoc network with the same desired SSID.
Profile Setting—Security Tab
Clicking the Security tab displays the following security options:
„
Authentication Mode
„
Encryption Method (Security off, WEP, TKIP, and AES)
„
Key settings (for legacy authentication modes) or 802.1X Authentication Protocol selection (for
802.1X authentication modes)
Figure 15: Security Tab—Authentication Modes
Doc. No. MV-S800473-00 Rev. B
Page 24
CONFIDENTIAL
Document Classification: Proprietary Information
Copyright © 2007 Marvell
August 14, 2007, 2.00
Marvell Wireless Configuration Utility User Interface
Profile Manager Tab
Note
3.2.3
The authentication modes available depend on the network type selected on the
Network Info tab.
For Ad-Hoc networks, only Open System and Shared Key are available.
Legacy Authentication Modes
The Marvell Wireless Configuration Utility currently supports the following legacy authentication
modes:
„
Open System—Open Authentication (no key or a pre-shared WEP key is required)
„
Shared Key—Shared Authentication (a pre-shared WEP key is required)
„
Auto Switch—Auto Select Authentication modes (no key or a pre-shared WEP key is required)
„
WPA-PSK—WPA Pre-Shared Key
„
WPA2-PSK—WPA2 Pre-Shared Key
If Open System or Auto Switch is selected as Authentication Mode, Security off and WEP are
available as Encryption Method. If Shared Key is selected as Authentication Mode, WEP is
pre-selected as Encryption Method. For details on how to configure the WEP key(s), see
Section 3.2.3.1.
If WPA-PSK or WPA2-PSK is selected as Authentication Mode, AES and TKIP are available as
Encryption Method. For details on how to define the pre-shared key, see Section 3.2.3.2.
Note
Copyright © 2007 Marvell
August 14, 2007, 2.00
The authentication modes available depend on the network type selected on the
Network Info tab.
For Ad-Hoc networks, only authentication modes without encryption or with WEP key
are available.
CONFIDENTIAL
Document Classification: Proprietary Information
Doc. No. MV-S800473-00 Rev. B
Page 25
CB-82/MB-82/EC-82/MC-82
User Guide
3.2.3.1
Open System / Shared Key / Auto Switch
Figure 16: Security Tab—Open System with WEP
The WEP key configuration for the authentication modes Open System, Shared Key, and Auto
Switch is identical:
1. Click Configure WEP Keys.
The Configure WEP Key window is displayed. For a detailed description of this window, see
Table 5 on page 27.
Figure 17: WEP Key Configuration Window
Doc. No. MV-S800473-00 Rev. B
Page 26
CONFIDENTIAL
Document Classification: Proprietary Information
Copyright © 2007 Marvell
August 14, 2007, 2.00
Marvell Wireless Configuration Utility User Interface
Profile Manager Tab
2.
3.
Select the required Key Format and Key Size.
Enter the Transmit Key(s).
Note
4.
5.
Up to four WEP keys are supported. The WEP key used for the transmission must be
identical on the sending and receiving station.
Click OK to return to the Security tab of the Profile Settings.
Select the WEP key to be used for the transmission.
Figure 18: WEP Key Setting
6.
Click Save to set the configuration.
Table 5:
F ie l d
Description
Key Format
Either ASCII characters or hexadecimal digits
Key Size
•
•
Transmit Key/Key Value
Key to be used as transmit key. The key value is in ASCII or hexadecimal,
depending on the format selected. The key value size shown depends on
the key size selected.
Copyright © 2007 Marvell
August 14, 2007, 2.00
WEP Key Configuration Window Description
40-bit, 5 character ASCII key size (40-bit, 10 hexadecimal digits)
104-bit, 13 character ASCII key size (104-bit, 26 hexadecimal digits)
CONFIDENTIAL
Document Classification: Proprietary Information
Doc. No. MV-S800473-00 Rev. B
Page 27
CB-82/MB-82/EC-82/MC-82
User Guide
3.2.3.2
WPA-PSK / WPA2-PSK
Figure 19: Security Tab—WPA2-PSK with TKIP
The definition of the pre-shared key is identical for both WPA-PSK/WPA2-PSK with TKIP/AES:
1. Enter the pre-shared key into the Passphrase and Confirm boxes.
The passphrase must contain between 8 and 63 ASCII characters.
2. Click Save to set the configuration.
Doc. No. MV-S800473-00 Rev. B
Page 28
CONFIDENTIAL
Document Classification: Proprietary Information
Copyright © 2007 Marvell
August 14, 2007, 2.00
Marvell Wireless Configuration Utility User Interface
Profile Manager Tab
3.2.4
802.1X Authentication Modes
The Marvell Wireless Configuration Utility currently supports the following 802.1X authentication
modes:
„
802.1X—Open System with 802.1X Authentication (EAP/TLS, PEAP, EAP/TTLS, LEAP or
EAP-FAST)
„
WPA—WPA with 802.1X Authentication (EAP/TLS, PEAP, EAP/TTLS, LEAP or EAP-FAST)
„
WPA2—WPA2 with 802.1X Authentication (EAP/TLS, PEAP, EAP/TTLS, LEAP or EAP-FAST)
For all 802.1X authentication modes, CCX support can be enabled.
If 802.1X (Open System) is selected as Authentication Mode, WEP is pre-selected as Encryption
Method. If WPA or WPA2 is selected, TKIP and AES are available as Encryption Method. For details
on how to define the different 802.1X authentication protocols (EAP/TLS, PEAP, EAP/TTLS, LEAP,
and EAP-FAST), see the following subsections.
3.2.4.1
802.1X / WPA / WPA2 with EAP/TLS
Figure 20: Security Tab—WPA2 with EAP/TLS (Use Certificate)
The definition of the EAP/TLS authentication protocol for the authentication modes 802.1X, WPA,
and WPA2 is identical:
1. Select EAP/TLS (Use Certificate) as 802.1X Authentication Protocol.
2. Click Configure.
The EAP/TLS (Use Certificate) window is displayed. For a detailed description of this window,
see Table 6 on page 34.
Copyright © 2007 Marvell
August 14, 2007, 2.00
CONFIDENTIAL
Document Classification: Proprietary Information
Doc. No. MV-S800473-00 Rev. B
Page 29
CB-82/MB-82/EC-82/MC-82
User Guide
Figure 21: EAP/TLS (Use Certificate) Configuration Window—Client Authentication
Tab
3.
4.
On the Client Authentication tab, enter your Login Name.
Click Browse.
The Select Certificate window is displayed. For a detailed description of this window, see
Table 7 on page 34.
Doc. No. MV-S800473-00 Rev. B
Page 30
CONFIDENTIAL
Document Classification: Proprietary Information
Copyright © 2007 Marvell
August 14, 2007, 2.00
Marvell Wireless Configuration Utility User Interface
Profile Manager Tab
Figure 22: Select Certificate Window (Client Certificates)
5.
In the Certificates in Store list, click the personal certificate to be used for the client
authentication.
Note
6.
7.
Copyright © 2007 Marvell
August 14, 2007, 2.00
If the required certificate is not yet installed on your system or if you do not know which
certificate to use, contact your network administrator.
Click Select to confirm your selection and to return to the EAP/TLS (Use Certificate) window.
If you want to specify particular server certificates to be accepted (instead of accepting any
certificate sent by the server), click the Server Authentication tab. For a detailed description of
this window, see Table 8 on page 35.
Otherwise, continue with step 14.
CONFIDENTIAL
Document Classification: Proprietary Information
Doc. No. MV-S800473-00 Rev. B
Page 31
CB-82/MB-82/EC-82/MC-82
User Guide
Figure 23: EAP/TLS Configuration Window—Server Authentication Tab
8.
9.
Select the required Server Validation Method.
For Accept only trusted certificates or Accept certificates from trusted server/domain,
click Add to select the appropriate certificate.
The Select Certificate window is displayed. For a detailed description of this window, see
Table 9 on page 35.
Doc. No. MV-S800473-00 Rev. B
Page 32
CONFIDENTIAL
Document Classification: Proprietary Information
Copyright © 2007 Marvell
August 14, 2007, 2.00
Marvell Wireless Configuration Utility User Interface
Profile Manager Tab
Figure 24: Select Certificate Window (Server Certificates)
10. On the Select Certificate window, select the Certificate Store.
11. From the Certificates in Store list, click the certificate to be used for the server authentication.
Note
If the required certificate is not yet installed on your system or if you do not know which
certificate to use, contact your network administrator.
12. Click Select to confirm your selection and to return to the EAP/TLS (Use Certificate) window.
13. If you have selected Accept certificates from trusted server/domain, enter the appropriate
server name or domain name into the Trusted Domain or Server box.
Copyright © 2007 Marvell
August 14, 2007, 2.00
CONFIDENTIAL
Document Classification: Proprietary Information
Doc. No. MV-S800473-00 Rev. B
Page 33
CB-82/MB-82/EC-82/MC-82
User Guide
Figure 25: Server Authentication—Trusted Domain or Server
14. Click OK to return to the Security tab of the Profile Settings.
15. If CCX compatibility is required, select the Enable Cisco Compatible Extensions (CCX) check
box.
16. Click Save to set the configuration.
Table 6:
Field/Button
Description
Login Name
Login name to the authentication server
Certificate
Certificate to be used for client authentication
View
Shows the selected certificate
Browse
Selects the certificate from the certificates store
Table 7:
Select Certificate Window Description (Client Certificates)
Ar ea
Description
Select Certificate Store
Certificate stores with certificates to be used for client authentication:
• My Personal Certificates
Contains personal certificates
• Certification Authority Certificates
Contains certificates issued by a Certification Authority (CA) (for
server authentication only)
• Root Certificates
Contains certificates issued by a CA who uses an own Trusted Root
CA certificate (for server authentication only)
• Software Publisher Certificates
Contains certificates issued by a software publisher (for server
authentication only)
Certificates in Store
Lists the personal certificates installed on the client system
Doc. No. MV-S800473-00 Rev. B
Page 34
EAP/TLS Configuration Window Description—Client Authentication Tab
CONFIDENTIAL
Document Classification: Proprietary Information
Copyright © 2007 Marvell
August 14, 2007, 2.00
Marvell Wireless Configuration Utility User Interface
Profile Manager Tab
Table 8:
Area/Button
Description
Server Validation Method
Certificates to be accepted for server authentication:
• Accept any server certificate
• Accept only trusted certificates
• Accept certificates from trusted server/domain
Trusted Certificates
Lists the trusted certificates installed on the client system
Required, when Accept only trusted certificates or Accept certificates
from trusted server/domain is selected. The appropriate root certificate
of the server/domain must also be installed on the client system.
View
Shows the selected certificate
Remove
Deletes the selected certificate from the Trusted Certificates list
Add
Selects the certificate from the certificates store
Trusted Domain or Server
Domain or server the certificate to be trusted is received from
Required, when Accept certificates from trusted server/domain is
selected
Table 9:
Select Certificate Window Description (Server Certificates)
Ar ea
Description
Select Certificate Store
Certificate stores with certificates to be used for server authentication:
• My Personal Certificates
Contains personal certificates (for client authentication only)
• Certification Authority Certificates
Contains certificates issued by a CA
• Root Certificates
Contains certificates issued by a CA who uses an own Trusted Root
CA certificate
• Software Publisher Certificates
Contains certificates issued by a software publisher
Certificates in Store
Lists the certificates installed in the selected certificate store on the client
system
Copyright © 2007 Marvell
August 14, 2007, 2.00
EAP/TLS Configuration Window Description—Server Authentication Tab
CONFIDENTIAL
Document Classification: Proprietary Information
Doc. No. MV-S800473-00 Rev. B
Page 35
CB-82/MB-82/EC-82/MC-82
User Guide
3.2.4.2
802.1X / WPA / WPA2 with PEAP
Figure 26: Security Tab—WPA2 with PEAP
The definition of the PEAP authentication protocol for the authentication modes 802.1X, WPA, and
WPA2 is identical:
1. Select Protected EAP (PEAP) as 802.1X Authentication Protocol.
2. Click Configure.
The Protected EAP (PEAP) window is displayed. For a detailed description of this window, see
Table 10 on page 40.
Doc. No. MV-S800473-00 Rev. B
Page 36
CONFIDENTIAL
Document Classification: Proprietary Information
Copyright © 2007 Marvell
August 14, 2007, 2.00
Marvell Wireless Configuration Utility User Interface
Profile Manager Tab
Figure 27: PEAP Configuration Window—Client Authentication Tab
3.
4.
5.
6.
Copyright © 2007 Marvell
August 14, 2007, 2.00
On the Client Authentication tab, enter your Login Name, Password, and Domain.
The domain information is optional.
From the Inner EAP Protocols list, select the EAP protocol to be used.
If required, change the order of preference.
If you have selected EAP-GTC, select the credentials to be used for login.
If you want to specify particular server certificates to be accepted (instead of accepting any
certificate sent by the server), click the Server Authentication tab. For a detailed description of
this window, see Table 11 on page 40.
Otherwise, continue with step 13.
CONFIDENTIAL
Document Classification: Proprietary Information
Doc. No. MV-S800473-00 Rev. B
Page 37
CB-82/MB-82/EC-82/MC-82
User Guide
Figure 28: PEAP Configuration Window—Server Authentication Tab
7.
8.
Select the required Server Validation Method.
For Accept only trusted certificates or Accept certificates from trusted server/domain,
click Add to select the appropriate certificate.
The Select Certificate window is displayed. For a detailed description of this window, see
Table 12 on page 41.
Doc. No. MV-S800473-00 Rev. B
Page 38
CONFIDENTIAL
Document Classification: Proprietary Information
Copyright © 2007 Marvell
August 14, 2007, 2.00
Marvell Wireless Configuration Utility User Interface
Profile Manager Tab
Figure 29: Select Certificate Window (Server Certificates)
9. On the Select Certificate window, select the Certificate Store.
10. From the Certificates in Store list, click the certificate to be used for the server authentication.
Note
If the required certificate is not yet installed on your system or if you do not know which
certificate to use, contact your network administrator.
11. Click Select to confirm your selection and to return to the Protected EAP (PEAP) window.
12. If you have selected Accept certificates from trusted server/domain, enter the server name
or the domain name into the Trusted Domain or Server box.
Copyright © 2007 Marvell
August 14, 2007, 2.00
CONFIDENTIAL
Document Classification: Proprietary Information
Doc. No. MV-S800473-00 Rev. B
Page 39
CB-82/MB-82/EC-82/MC-82
User Guide
Figure 30: Server Authentication—Trusted Domain or Server
13. Click OK to return to the Security tab of the Profile Settings.
14. If CCX compatibility is required, select the Enable Cisco Compatible Extensions (CCX) check
box.
15. Click Save to set the configuration.
Table 10: PEAP Configuration Window Description—Client Authentication Tab
A r ea / F ie l d
Description
Login Name
Login name to the authentication server
Password
Password for login to the authentication server
Domain
Domain name for login to the authentication server (optional)
Inner EAP Protocols
EAP protocol to be used for inner (client) authentication:
• EAP/MS-CHAP V2
Uses Microsoft Challenge Handshake Authentication Protocol
(CHAP) v2 for authentication
• EAP-GTC
Uses Generic Token Card (GTC) for authentication
Credentials to use for
inner EAP-GTC
Credentials to be used for inner (client) authentication:
• My Password
Uses a user-specific password
• Token information
Uses a token that generates a one-time password
Required, when EAP-GTC is selected as Inner EAP Protocol
Table 11: PEAP Configuration Window Description—Server Authentication Tab
Area/Button
Description
Server Validation Method
Certificates to be accepted for server authentication:
• Accept any server certificate
• Accept only trusted certificates
• Accept certificates from trusted server/domain
Trusted Certificates
Lists the trusted certificates installed on the client system
Required, when Accept only trusted certificates or Accept certificates
from trusted server/domain is selected. The appropriate root certificate
of the server/domain must also be installed on the client system.
View
Shows the selected certificate
Remove
Deletes the selected certificate from the Trusted Certificates list
Doc. No. MV-S800473-00 Rev. B
Page 40
CONFIDENTIAL
Document Classification: Proprietary Information
Copyright © 2007 Marvell
August 14, 2007, 2.00
Marvell Wireless Configuration Utility User Interface
Profile Manager Tab
Table 11: PEAP Configuration Window Description—Server Authentication Tab
Area/Button
Description
Add
Selects the certificate from the certificates store
Trusted Domain or Server
Domain or server the certificate to be trusted is received from
Required, when Accept certificates from trusted server/domain is
selected
Table 12: Select Certificate Window Description (Server Certificates)
3.2.4.3
Ar ea
Description
Select Certificate Store
Certificate stores with certificates to be used for server authentication:
• My Personal Certificates
Contains personal certificates (for client authentication only)
• Certification Authority Certificates
Contains certificates issued by a CA
• Root Certificates
Contains certificates issued by a CA who uses an own Trusted Root
CA certificate
• Software Publisher Certificates
Contains certificates issued by a software publisher
Certificates in Store
Lists the certificates installed in the selected certificate store on the client
system
802.1X / WPA / WPA2 with EAP/TTLS
Figure 31: Security Tab—WPA2 with EAP/TTLS
Copyright © 2007 Marvell
August 14, 2007, 2.00
CONFIDENTIAL
Document Classification: Proprietary Information
Doc. No. MV-S800473-00 Rev. B
Page 41
CB-82/MB-82/EC-82/MC-82
User Guide
The definition of the EAP/TTLS authentication protocol for the authentication modes 802.1X, WPA,
and WPA2 is identical:
1. Select EAP/Tunneled TLS (TTLS) as 802.1X Authentication Protocol.
2. Click Configure.
The EAP/Tunneled TLS (TTLS) window is displayed. For a detailed description of this window,
see Table 13 on page 45.
Figure 32: EAP/TTLS Configuration Window—Client Authentication Tab
3.
4.
On the Client Authentication tab, enter your Anonymous Name, Login Name, Password,
and Domain.
The domain information is optional.
If you want to specify particular server certificates to be accepted (instead of accepting any
certificate sent by the server), click the Server Authentication tab. For a detailed description of
this window, see Table 14 on page 45.
Otherwise, continue with step 11.
Doc. No. MV-S800473-00 Rev. B
Page 42
CONFIDENTIAL
Document Classification: Proprietary Information
Copyright © 2007 Marvell
August 14, 2007, 2.00
Marvell Wireless Configuration Utility User Interface
Profile Manager Tab
Figure 33: EAP/TTLS Configuration Window—Server Authentication Tab
5.
6.
Copyright © 2007 Marvell
August 14, 2007, 2.00
Select the required Server Validation Method.
For Accept only trusted certificates or Accept certificates from trusted server/domain,
click Add to select the appropriate certificate.
The Select Certificate window is displayed. For a detailed description of this window, see
Table 15 on page 46.
CONFIDENTIAL
Document Classification: Proprietary Information
Doc. No. MV-S800473-00 Rev. B
Page 43
CB-82/MB-82/EC-82/MC-82
User Guide
Figure 34: Select Certificate Window (Server Certificates)
7.
8.
On the Select Certificate window, select the Certificate Store.
From the Certificates in Store list, click the certificate to be used for the server authentication.
Note
If the required certificate is not yet installed on your system or if you do not know which
certificate to use, contact your network administrator.
9. Click Select to confirm your selection and to return to the EAP/Tunneled TLS (TTLS) window.
10. If you have selected Accept certificates from trusted server/domain, enter the server name
or the domain name into the Trusted Domain or Server box.
Doc. No. MV-S800473-00 Rev. B
Page 44
CONFIDENTIAL
Document Classification: Proprietary Information
Copyright © 2007 Marvell
August 14, 2007, 2.00
Marvell Wireless Configuration Utility User Interface
Profile Manager Tab
Figure 35: Server Authentication—Trusted Domain or Server
11. Click OK to return to the Security tab of the Profile Settings.
12. If CCX compatibility is required, select the Enable Cisco Compatible Extensions (CCX) check
box.
13. Click Save to set the configuration.
Table 13: EAP/TTLS Configuration Window Description—Client Authentication
Tab
F ie l d
Description
Inner Authentication Protocol
Protocol to be used for inner (client) authentication
Anonymous Name
Anonymous login name to the authentication server
Login Name
Login name to the authentication server
Password
Password for login to the authentication server
Domain
Domain name for login to the authentication server (optional)
Table 14: EAP/TTLS Configuration Window Description—Server Authentication
Tab
Area/Button
Description
Server Validation Method
Certificates to be accepted for server authentication:
• Accept any server certificate
• Accept only trusted certificates
• Accept certificates from trusted server/domain
Trusted Certificates
Lists the trusted certificates installed on the client system
Required, when Accept only trusted certificates or Accept certificates
from trusted server/domain is selected. The appropriate root certificate
of the server/domain must also be installed on the client system.
View
Shows the selected certificate
Remove
Deletes the selected certificate from the Trusted Certificates list
Add
Selects the certificate from the certificates store
Trusted Domain or Server
Domain or server the certificate to be trusted is received from
Required, when Accept certificates from trusted server/domain is
selected
Copyright © 2007 Marvell
August 14, 2007, 2.00
CONFIDENTIAL
Document Classification: Proprietary Information
Doc. No. MV-S800473-00 Rev. B
Page 45
CB-82/MB-82/EC-82/MC-82
User Guide
Table 15: Select Certificate Window Description (Server Certificates)
3.2.4.4
Ar ea
Description
Select Certificate Store
Certificate stores with certificates to be used for server authentication:
• My Personal Certificates
Contains personal certificates (for client authentication only)
• Certification Authority Certificates
Contains certificates issued by a CA
• Root Certificates
Contains certificates issued by a CA who uses an own Trusted Root
CA certificate
• Software Publisher Certificates
Contains certificates issued by a software publisher
Certificates in Store
Lists the certificates installed in the selected certificate store on the client
system
802.1X / WPA / WPA2 with LEAP
Figure 36: Security Tab—WPA2 with LEAP
The definition of the LEAP authentication protocol for the authentication modes 802.1X, WPA, and
WPA2 is identical:
1. Select Light EAP (LEAP) as 802.1X Authentication Protocol.
2. Click Configure.
The LEAP Configuration window is displayed. For a detailed description of this window, see
Table 16 on page 48.
Doc. No. MV-S800473-00 Rev. B
Page 46
CONFIDENTIAL
Document Classification: Proprietary Information
Copyright © 2007 Marvell
August 14, 2007, 2.00
Marvell Wireless Configuration Utility User Interface
Profile Manager Tab
Figure 37: LEAP Configuration Window
3.
Under Logon Settings, select the user credentials (and, if required, Login Name, Password,
and Domain) to be used for the client authentication.
Use Windows user name and password is only available if Enable single sign-on is
selected.
„
„
Note
4.
5.
6.
7.
Copyright © 2007 Marvell
August 14, 2007, 2.00
To enable single sign-on, administrator rights are required.
Using single sign-on authentication for the first time requires a restart of your
system after having saved the LEAP configuration.
If required, specify further settings under Options.
Click OK to return to the Security tab of the Profile Settings.
If CCX compatibility is required, select the Enable Cisco Compatible Extensions (CCX) check
box.
Click Save to set the configuration.
CONFIDENTIAL
Document Classification: Proprietary Information
Doc. No. MV-S800473-00 Rev. B
Page 47
CB-82/MB-82/EC-82/MC-82
User Guide
Table 16: LEAP Configuration Window Description
A r ea / F ie l d
Description
Logon Settings
Credentials to be used for login to the authentication server:
• Use stored user credentials below
• Login Name—Login name to the authentication server
• Password—Password for login to the authentication server
• Domain—Domain name for login to the authentication server (optional)
•
•
Options
•
•
•
•
Doc. No. MV-S800473-00 Rev. B
Page 48
Prompt for User Credentials
Credentials are to be entered during authentication (are not stored in the
profile).
Use Windows user name and password (available only when Enable single
sign-on is selected)
Windows user name and password are used for login to the authentication
server. Additionally, Include Windows domain in Windows logon information
can be selected.
Enable single sign-on
Windows user credentials are used for login to the authentication server (see
Logon Settings)
Allow fast roaming (CCKM)
Enables Cisco Centralized Key Management (CCKM) which allows for fast
roaming without involving the authentication server
Authentication timeout value (seconds)
Time to be waited before assuming the authentication failed. Default value is
90.
Restrict time finding domain controller to (seconds)
Maximum time allowed to find the domain controller, included in the overall
authentication time. Default value is 60.
CONFIDENTIAL
Document Classification: Proprietary Information
Copyright © 2007 Marvell
August 14, 2007, 2.00
Marvell Wireless Configuration Utility User Interface
Profile Manager Tab
3.2.4.5
802.1X / WPA / WPA2 with EAP-FAST
Figure 38: Security Tab—WPA2 with EAP-FAST
The definition of the EAP-FAST authentication protocol for the authentication modes 802.1X, WPA,
and WPA2 is identical:
1. Select EAP-FAST as 802.1X Authentication Protocol.
2. Click Configure.
The EAP-FAST Configuration window is displayed. For a detailed description of this window,
see Table 17 on page 51.
Copyright © 2007 Marvell
August 14, 2007, 2.00
CONFIDENTIAL
Document Classification: Proprietary Information
Doc. No. MV-S800473-00 Rev. B
Page 49
CB-82/MB-82/EC-82/MC-82
User Guide
Figure 39: EAP-FAST Configuration Window
3.
Under Logon Settings, select the user credentials (and, if required, Login Name, Password,
and Domain) to be used for the client authentication.
Use Windows user name and password is only available if Enable single-signon is
selected.
„
„
Note
4.
5.
6.
If automatic Protected Access Credentials (PAC) provisioning is required, select the Allow
Automatic PAC Provisioning check box, and enter the appropriate Authority ID.
If required, specific further settings under Options.
Click OK to return to the Security tab of the Profile Settings.
Doc. No. MV-S800473-00 Rev. B
Page 50
To enable single sign-on, administrator rights are required.
Using single sign-on authentication for the first time requires a restart of your
system after having saved the EAP-FAST configuration.
CONFIDENTIAL
Document Classification: Proprietary Information
Copyright © 2007 Marvell
August 14, 2007, 2.00
Marvell Wireless Configuration Utility User Interface
Profile Manager Tab
7.
8.
If CCX compatibility is required, select the Enable Cisco Compatible Extensions (CCX) check
box.
Click Save to set the configuration.
Table 17: EAP-FAST Configuration Window Description
Area/Button
Description
Logon Settings
Credentials to be used for login to the authentication server:
• Use stored user credentials below
• Login Name—Login name to the authentication server
• Password—Password for login to the authentication
server
• Domain—Domain name for login to the authentication
•
•
Protected Access Credentials
(PAC)
Allows automatic PAC provisioning
Import
Selects authority ID of the authentication server
Options
•
•
•
•
Copyright © 2007 Marvell
August 14, 2007, 2.00
server (optional)
Prompt for User Credentials
Credentials are to be entered during authentication (are not
stored in the profile).
Use Windows user name and password (available only
when Enable single sign-on is selected)
Windows user name and password are used for login to the
authentication server. Additionally, Include Windows
domain in Windows logon information can be selected.
Enable single sign-on
Windows user credentials are used for login to the
authentication server (see Logon Settings)
Allow fast roaming (CCKM)
Enables Cisco Centralized Key Management (CCKM) which
allows for fast roaming without involving the authentication
server
Authentication timeout value (seconds)
Time to be waited before assuming the authentication failed.
Default value is 90.
Restrict time finding domain controller to (seconds)
Maximum time allowed to find the domain controller,
included in the overall authentication time. Default value
is 60.
CONFIDENTIAL
Document Classification: Proprietary Information
Doc. No. MV-S800473-00 Rev. B
Page 51
CB-82/MB-82/EC-82/MC-82
User Guide
3.2.5
Profile Setting—Protocol Tab
The Protocol tab allows you to set or change the protocol information.
Figure 40: Protocol Tab
Do not change settings
If this check box is selected, the protocol setting is not changed when the profile is applied.
Use below settings
If the Do not change setting check box is not selected, the protocol settings include the following
parameters.
Table 18: Protocol Tab Description
F ie l d
Description
Power Save Mode
Sets the power mode. Available options are Continuous Access or Max
Power Save. The default setting is Continuous Access.
Preamble (802.11b)
Sets the Radio Preamble to Auto, Short or Long.
Transmit Rate
The range of the data rate depends on the type of AP that the client card
is connected to. The default setting is Auto Select.
MCS index will be allowed to select when the 802.11n Network check
box in the Network Info tab is selected.
Fragment Threshold
Sets the fragmentation threshold (the size that packets are fragmented
into for transmission). The default setting is 2346.
RTS/CTS Threshold
Sets the packet size at which the AP issues a Request-To-Send (RTS) or
Clear-To-Send (CTS) frame before sending the packet. The default
setting is 2347.
Reset
Resets the protocol settings to their default values
Doc. No. MV-S800473-00 Rev. B
Page 52
CONFIDENTIAL
Document Classification: Proprietary Information
Copyright © 2007 Marvell
August 14, 2007, 2.00
Marvell Wireless Configuration Utility User Interface
Site Survey Tab
3.3
Site Survey Tab
The Site Survey tab displays a list of all peer-to-peer (Ad-Hoc) and AP stations within range of the
client card.
Figure 41: Site Survey Tab
3.3.1
Site Survey—Networks Filter
This section lets you customize which sites are displayed in the Site Survey list:
„
„
„
Copyright © 2007 Marvell
August 14, 2007, 2.00
Display Peer-To-Peer stations—selecting this check box displays all peer-to-peer (Ad-Hoc)
stations within range.
Display 802.11g Access Points—selecting this check box displays all 802.11g APs within
range.
Display 802.11b Access Points—selecting this check box displays all 802.11b APs within
range.
CONFIDENTIAL
Document Classification: Proprietary Information
Doc. No. MV-S800473-00 Rev. B
Page 53
CB-82/MB-82/EC-82/MC-82
User Guide
3.3.2
Site Survey—List of Detected Stations
This section reports information on the peer-to-peer (Ad-Hoc) stations or AP stations detected.
Figure 42: Site Survey—List of Detected Stations
802.11g AP Icon
Ad-Hoc Network
802.11b AP Icon
Circle means
connected
Table 19: List of Detected Stations Description
F ie l d
Description
Network SSID
Network SSID label (i.e., the Network Name). The Network Name is a text string.
MAC Address
MAC address, a hardware address that uniquely identifies each node of a network
Security
Security enabled or disabled
CH
Channel used by the detected device
Signal
Signal strength of the detected device as a percentage
Icons
The following icons may be displayed left of the Network SSID:
• An antenna icon with a subscript b indicates an 802.11b AP.
• An antenna icon with a subscript g indicates an 802.11g AP.
• A circle around the antenna icon means the client card is connected to this
network.
• A slash icon indicates an Ad-Hoc network.
WMM
Wireless Multimedia Enhancements (WMM) supported by the detected device
EWC
Draft-802.11n functionality supported by the detected device
Network Type
Type of environment connected to: Ad-Hoc or Infrastructure
Doc. No. MV-S800473-00 Rev. B
Page 54
CONFIDENTIAL
Document Classification: Proprietary Information
Copyright © 2007 Marvell
August 14, 2007, 2.00
Marvell Wireless Configuration Utility User Interface
Site Survey Tab
3.3.3
Site Survey—Filter Button
Clicking the Filter button displays the Advanced Filter window.
Figure 43: Site Survey—Advanced Filter Window
3.3.3.1
Network SSID
„
„
3.3.3.2
Network BSSID
„
„
3.3.3.3
Any BSSID—no specific BSSID is used when scanning for available networks in the area.
Find network with this BSSID—the utility searches for the specified BSSID.
Select Channel
„
„
„
3.3.4
Any SSID—no specific SSID is used when scanning for available networks in the area.
Find network with this SSID—the utility searches for the specified SSID.
Note to US model owner: To comply with US FCC regulation, the country selection function has
been completely removed from all US models. The above function is for non-US models only.
Scan all channels—all channels are scanned when searching for available networks in the
area.
Scan channel Only—only the specified channel is scanned when searching for available
networks in the area.
Scan Channel to Channel—a range of channels are scanned when searching for available
networks in the area.
Site Survey—Refresh Button
To request a survey of the wireless networks in the area, click Refresh.
3.3.5
Site Survey—Associate Button
To establish a connection, select an available network, and then click Associate. Alternatively, the
connection can be established by double-clicking the selected network.
Copyright © 2007 Marvell
August 14, 2007, 2.00
CONFIDENTIAL
Document Classification: Proprietary Information
Doc. No. MV-S800473-00 Rev. B
Page 55
CB-82/MB-82/EC-82/MC-82
User Guide
3.4
Statistics Tab
Clicking the Statistics tab displays the statistics of the current connect session.
Figure 44: Statistics Tab
3.4.1
Signal Strength
The color-coded Signal Strength bar displays the signal strength of the last packet received by the
client card. Signal strength is reported as a percentage. A signal in the red indicates a bad
connection. A signal in the green indicates a good connection.
Doc. No. MV-S800473-00 Rev. B
Page 56
CONFIDENTIAL
Document Classification: Proprietary Information
Copyright © 2007 Marvell
August 14, 2007, 2.00
Marvell Wireless Configuration Utility User Interface
Statistics Tab
3.4.2
Transmit Section
The Transmit section displays the information on the packets sent.
Figure 45: Transmit Section
Table 20: Transmit Section Description
F ie l d
Description
Total Packet
Reports the total number of packets transmitted
Unicast Packet
Reports the number of packets transmitted by the client card that were
destined for a single network node
Multicast Packet
Reports the number of packets transmitted by the client card that were
destined for more than one network node
Single Retries
Reports the number of packets that require one retry before the client card
received an acknowledgement.
NOTE: After the client card sends a packet, it waits for an acknowledge
from the receiving radio to confirm that the packet was
successfully received. If the acknowledge is not received within a
specified period of time, the client card retransmits the packet.
Multiple Retries
Reports the number of packets that require more than one retry before the
client card received an acknowledgement
Failed Count
Reports the number of packets that were not successfully transmitted
because the client card did not receive an acknowledge within the
specified period of time
RTS Success
Reports the number of RTS attempts that were successful
RTS Failure
Reports the number of RTS attempts that were not successful
ACK Error
Reports the number of unicast transmit attempts for which no
acknowledgement was received
Copyright © 2007 Marvell
August 14, 2007, 2.00
CONFIDENTIAL
Document Classification: Proprietary Information
Doc. No. MV-S800473-00 Rev. B
Page 57
CB-82/MB-82/EC-82/MC-82
User Guide
3.4.3
Receive Section
The Receive section displays the information on the packets received.
Figure 46: Receive Section
Table 21: Receive Section Description
3.4.4
F ie l d
Description
Total Packet
Reports the total number of packets received
Unicast Packet
Reports the number of packets received by the client card that were
destined for a single network node
Multicast Packet
Reports the number of packets received by the client card that were
destined for more than one network node
Duplicate Frame
Reports the number of duplicate frames received
Received Beacons
Reports the number of beacons received after association is established
Beacon Loss
Reports the number of missing beacons after association is established
Protocol Section
The Protocol section displays the information on the protocol status.
Figure 47: Protocol Section
18
Doc. No. MV-S800473-00 Rev. B
Page 58
CONFIDENTIAL
Document Classification: Proprietary Information
Copyright © 2007 Marvell
August 14, 2007, 2.00
Marvell Wireless Configuration Utility User Interface
Advanced Tab
Table 22: Protocol Section Description
3.5
F ie l d
Description
Preamble
Displays radio preamble type:
• Auto
• Short
• Long
Tx Power
Displays transmit power mode (in dBm)
Advanced Tab
The Advanced tab displays the advanced parameters available for the installed Marvell client cards.
Figure 48: Advanced Tab
3.5.1
Advanced Tab—Marvell Wireless Card
This section of the Advanced tab reports the type of Marvell client card installed.
Copyright © 2007 Marvell
August 14, 2007, 2.00
CONFIDENTIAL
Document Classification: Proprietary Information
Doc. No. MV-S800473-00 Rev. B
Page 59
CB-82/MB-82/EC-82/MC-82
User Guide
3.5.2
Advanced Tab—Miscellaneous
Figure 49: Miscellaneous Section
Table 23: Advanced Tab Miscellaneous Section Description
3.6
F ie l d
Description
Auto connect if link loss or no
connection (use checked profiles in
)
Clear this check box to disable the auto-configuration feature.
Whenever there is a link loss, auto-configuration tries to
establish a connection to the checked profiles in the Profile
Manager window.
Enable WMM
Select this check box to enable/disable the Wireless Multimedia
Enhancements (WMM) feature.
BoostMode
Select this check box for performance enhancement.
Enable WPS
Select this check box to enable Wireless Provisioning Services
(WPS).
Worldwide Regulatory Domain
Select this check box to set the regulatory domain
DFS Mode
Select this check box to enable Dynamic Frequency Selection
(DFS)
AutoLink Tab
To enable AutoLink mode, proceed as follows:
1.
Toggle the AutoLink button on the Access Point to enable AutoLink mode.
Figure 50: Access Point AutoLink Button
Doc. No. MV-S800473-00 Rev. B
Page 60
CONFIDENTIAL
Document Classification: Proprietary Information
Copyright © 2007 Marvell
August 14, 2007, 2.00
Marvell Wireless Configuration Utility User Interface
AutoLink Tab
2.
On the AutoLink tab, click AutoLink.
Within 60 seconds, the AutoLink will be completed.
Figure 51: AutoLink Tab
Copyright © 2007 Marvell
August 14, 2007, 2.00
CONFIDENTIAL
Document Classification: Proprietary Information
Doc. No. MV-S800473-00 Rev. B
Page 61
CB-82/MB-82/EC-82/MC-82
User Guide
AutoLink is complete.
Figure 52: AutoLink Tab (AutoLink Complete)
Doc. No. MV-S800473-00 Rev. B
Page 62
CONFIDENTIAL
Document Classification: Proprietary Information
Copyright © 2007 Marvell
August 14, 2007, 2.00
Marvell Wireless Configuration Utility User Interface
Admin Tab
3.7
Admin Tab
The Admin tab allows you to import and export profiles.
Figure 53: Admin Tab
3.7.1
Admin Tab—Import Profiles
To import a profile, proceed as follows:
1.
2.
3.
3.7.2
Click Import Profiles.
Select the path and filename of the profile.
Click Open.
Admin Tab—Export Profiles
To export a profile, proceed as follows:
1.
2.
3.
Copyright © 2007 Marvell
August 14, 2007, 2.00
Click Export Profiles.
Select or enter the path and filename of the profile.
Click Save.
CONFIDENTIAL
Document Classification: Proprietary Information
Doc. No. MV-S800473-00 Rev. B
Page 63
CB-82/MB-82/EC-82/MC-82
User Guide
3.7.3
Admin Tab—Autostart Marvell Wireless Configuration
Utility
Select the Autostart Marvell Wireless Client Card Configuration Utility at System Startup check
box to automatically start the Marvell Wireless Configuration Utility at system startup
(recommended).
3.7.4
Admin Tab—Stop Windows Wireless Zero Configuration
Service
When using the Marvell Wireless Configuration Utility, Marvell recommends turning off the Windows
Wireless Zero Configuration Service, which is enabled by default. Both utilities should not be used at
the same time. To turn off the Windows Wireless Zero Configuration Service, select the Stop
Windows Wireless Zero Configuration Service check box.
3.8
About Tab
The About tab displays information about the Marvell Wireless Client Card Configuration Utility.
Figure 54: About Tab
Doc. No. MV-S800473-00 Rev. B
Page 64
CONFIDENTIAL
Document Classification: Proprietary Information
Copyright © 2007 Marvell
August 14, 2007, 2.00
Compliance Statements
Federal Communications Commission (FCC) Compliance
Compliance Statements
A.1
Federal Communications Commission (FCC)
Compliance
This
equipment
hashas
been
tested
and found
to comply
with thewith
limits
a Class
digital device,
pursuant
This
equipment
been
tested
and found
to comply
theforlimits
for B
a Class
B digital
device,to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
againstand
harmful
interference
a residential
installation.
Thisharmful
equipment
generates,
uses,
and can
installed
used in
accordance in
with
the instructions,
may cause
interference
to radio
communications.
radiate radio
frequency
energy.
not installed
used in
in aaccordance
with the instructions,
it may
However,
there is
no guarantee
that If
interference
will and
not occur
particular installation.
If this equipment
does
cause
harmful
interference
to radio
communications.
However,
is no guarantee
thatequipment off
cause
harmful
interference
to radio
or television
reception, which
can bethere
determined
by turning the
and
on, the userwill
is encouraged
to atryparticular
to correct installation.
the interference by one of the following measures:
interference
not occur in
If this equipment
cause harmful
- Reorient
or relocatedoes
the receiving
antenna.interference to radio or television reception, which can be
determined
by tuning between
the equipment
off andand
on,receiver.
the user is encouraged to try and correct the
- Increase
the separation
the equipment
- Connect
the equipment
an outlet
a circuit different
from that
interference
by one orinto
more
of theonfollowing
measures:
to which the receiver is connected.
„
Reorient or relocate the receiving antenna.
- Consult the dealer or an experienced radio/TV technician for help.
„
Increase the distance between the equipment and the receiver.
This
complies
with Part 15toofoutlet
the FCC
Operation
subject
thewhich
following
conditions:
(1) This
„ device
Connect
the equipment
on Rules.
a circuit
differentisfrom
thattoto
the two
receiver
is
device connected.
may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
„
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could
void
the user's authority to operate this equipment.
Modifications
A.2
Any changes
or modifications not expressly approved by the party responsible for compliance could
IMPORTANT
NOTE:
voidRadiation
the user's
authority
to operate the equipment.
FCC
Exposure
Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Industry Canada Notice
This device complies with Canadian RSS-210.
IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to channels 1 through 11.
“This
Class
digital apparatus
complies
with under
Canadian
ICES-003”
This
device
is B
intended
only for OEM
integrators
the following
conditions:
1)Cet
Theappareil
antenna must
be installed
that B
20est
cmconforme
is maintained
antennadu
and
users, and
numérique
de lasuch
classe
à labetween
norme the
NMB-003
Canada
2) The transmitter module may not be co-located with any other transmitter or antenna,
is subject
conditions:
(1) this
device
may to
not
cause
interference,
3)Operation
For all products
markettointhe
US,following
OEM hastwo
to limit
the operation
channels
in CH1
CH11
for 2.4G
band by and
(2) thisfirmware
device must
accept tool.
any OEM
interference,
including
may cause
undesired
supplied
programming
shall not supply
any interference
tool or info to that
the end-user
regarding
to Regulatory
operation
of this device.”
Domain
change.
As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is
L'utilisation
dispositif
est autorisée
aux
conditions
suivantes required
: (1) il ne
doit
pas
still
responsiblede
force
testing
their end-product
for seulement
any additional
compliance
requirements
with
this
module
produire
brouillage
et device
(2) l'utilisateur
dispositif
doit
étre prêt àetc.).
accepter tout brouillage
installed
(forde
example,
digital
emissions,du
PC
peripheral
requirements,
radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du
IMPORTANT
dispositif. NOTE: In the event that these conditions can not be met (for example certain laptop configurations
or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID
The
“IC”on
before
theproduct.
equipment
certification
number
theresponsible
Industry Canada
can
notterm
be used
the final
In these
circumstances,
the only
OEMsignifies
integratorthat
will be
for retechnicalthe
specifications
were met.
evaluating
end product (including
the transmitter) and obtaining a separate FCC authorization.
To reduce potential radio interference to other users, the antenna type and its gain should be so
End Product Labeling
chosen
that the
equivalent
isotropically
radiated
power
(EIRP)
is not more
than
that required
for cm
This
transmitter
module
is authorized
only for use
in device
where
the antenna
may be
installed
such that 20
successful
communication.
may
be maintained
between the antenna and users. The final end product must be labeled in a visible area with
the following: “Contains FCC ID: MCL74487504”.
To prevent radio interference to the licensed service, this device is intended to be operated indoors
and away from windows to provide
maximum
shielding.the
Equipment
Manual
InformationTo
End User (or its transmit antenna) that is
installed
outdoorshas
is to
subject
to licensing.
The
OEM integrator
be aware
not to provide information to the end user regarding how to install or remove
this RF module in the user's manual of the end product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in this manual.
Copyright © 2007 Marvell
August 14, 2007, 2.00
CONFIDENTIAL
Document Classification: Proprietary Information
Doc. No. MV-S800473-00 Rev. B
Page 65
CB-82/MB-82/EC-82/MC-82
User Guide
A.2
A.3
Europe—EU Declaration of Conformity and
Restrictions
Hereby, Marvell Semiconductor, Inc., declares that this telecommunication equipment complies with
all the provisions of the EC directives listed below and meets the relevant parts of the related
technical specifications:
Compliance with R&TTE (Radio & Telecommunications Terminal Equipment) Directive 99/5/EC,
Article 10.5
„
EN 300 328 v1.6.1 (2004-11) – Electromagnetic compatibility and Radio spectrum Matters
(ERM); Wideband Transmission Systems; Data transmission equipment operating in the
2,4GHz ISM band and using spread spectrum modulation techniques; Harmonized EN covering
essential requirements under article 3.2 of the R&TTE directive.
Compliance with Electromagnetic Compatibility (EMC) Directive 89/336/EEC
„
EN 301 489-17 v1.2.1 (2002-08) – Electromagnetic compatibility and Radio Spectrum Matters
(ERM); Electromagnetic Compatibility (EMC) standard for radio equipment and services;
Part 17: Specific conditions for wideband data and high performance RLAN (HIPERLAN)
equipment.
Compliance with Low Voltage Directive 73/23/EEC
„
EN 60950:2001 – Safety of Information Technology Equipment, including electrical business
equipment.
„
EN 50371:2002 – Generic standard to demonstrate the compliance of low power electronic and
electric apparatus with the basic restrictions related to human exposure to electromagnetic
fields.
„
EN 50385:2002 – Product standard to demonstrate the compliances of radio base stations and
fixed terminal stations for wireless telecommunication systems with the basic restrictions or the
reference levels related to human exposure to radio frequency electromagnetic fields.
This equipment is marked with the
European community.
Marking by the symbol
0984
symbol and can be used throughout the
indicates that usage restrictions apply.
2.4 GHz for Metropolitan France
In all Metropolitan départements, wireless LAN frequencies can be used under the following
conditions, either for public or private use:
„
Indoor use: maximum power (EIRP) of 100 mW for the entire 2400 - 2483.5 MHz frequency
band
„
Outdoor use: maximum power (EIRP) of 100 mW for the 2400 - 2454 MHz band and with
maximum power (EIRP) of 10 mW for the 2454 - 2483 MHz band
Caution
Doc. No. MV-S800473-00 Rev. B
Page 66
Exposure to Radio Frequency Radiation
To comply with RF exposure compliance requirements, a separation distance of at least
20 cm must be maintained between the antenna of this device and all persons. This
device must not be co-located or operating in conjunction with any other antenna or
transmitter.
CONFIDENTIAL
Document Classification: Proprietary Information
Copyright © 2007 Marvell
August 14, 2007, 2.00
Compliance Statements
Taiwan DGT
A.3
A.4
Taiwan NCC
DGT
2.4 GHz Band Products
「本產品內含射頻模組：XXXyyyLPDzzzz-x
A.4
Industry Canada Statement
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the
following two
conditions:
1) this device may not cause interference and
2) this device must accept any interference, including interference that may cause undesired operation of the
device
2.42
This device has been designed to operate with an antenna having a maximum gain of 1.51dBi.
Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna
impedance is 50 ohms.
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the
EIRP is not more than required for successful communication.
IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and
2) The transmitter module may not be co-located with any other transmitter or antenna,
3) For all products market in Canada, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band by supplied
firmware programming tool. OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain change.
As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still
responsible for testing their end-product for any additional compliance requirements required with this module installed (for
example, digital device emissions, PC peripheral requirements, etc.).
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location
with another transmitter), then the IC authorization is no longer considered valid and the IC ID can not be used on the final
product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the
transmitter) and obtaining a separate IC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be
maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains
IC: 2878D-74487504”.
Manual InformationTo the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module
Copyright © 2007
CONFIDENTIAL
Doc. No. MV-S800473-00 Rev. B
in theMarvell
user's manual of the end product which integrates
this module.
The 2.00
end user manual shall includeDocument
all required
regulatoryProprietary
information/warning
August 14, 2007,
Classification:
Information as show in this manual.
Page 67

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print
XMP Toolkit                     : 3.1-701
Modify Date                     : 2008:02:14 18:07:11+08:00
Create Date                     : 2008:02:14 16:09:15+08:00
Metadata Date                   : 2008:02:14 18:07:11+08:00
Creator Tool                    : FrameMaker 7.0
Format                          : application/pdf
Title                           : CB-82/MB-82/EC-82/MC-82 WLAN Client Cards User Guide
Creator                         : Marvell
Document ID                     : uuid:d5bf17e9-440a-4eb2-94a2-6ebd3e31bc1f
Instance ID                     : uuid:fd47ed60-f468-4b1b-931a-ec8af565a0dc
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Has XFA                         : No
Page Count                      : 67
Author                          : Marvell

EXIF Metadata provided by EXIF.tools