HON HAI PRECISION IND J20H086 WiFi/BT Module User Manual J20H086 01 User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2706069
Application ID	l0QlwsRcb9oBNhr96f92DQ==
Document Description	User Manual.pdf
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	20.09kB (251101 bits)
Date Submitted	2015-08-06 00:00:00
Date Available	2016-02-02 00:00:00
Creation Date	2015-07-15 19:39:44
Producing Software	Acrobat Distiller 8.1.0 (Windows)
Document Lastmod	2015-07-17 12:05:47
Document Title	Microsoft Word - J20H086.01_User_Manual
Document Creator	PScript5.dll Version 5.2
Document Author:	eku

J20H086
User Manual
Technology
Approval Sheet Rev.
Foxconn Part No.
Sony Part No.
Prepared by
WLAN Module
1.0
J20H086
Reviewed by
Approved by
CONTENTS
REVISION HISTORY ........................................................................ 3
PRODUCT OVERVIEW ........................................................................ 4
2.1
SCOPE ........................................................................ 4
MODULE HARDWARE OVERVIEW ................................................................ 5
3.1
3.2
3.3
APPLICATION
FEATURES ............................................................................... 5
INTERFACE AND CONNECTOR ................................................................... 5
PCB ASSEMBLY DIMENSION ................................................................... 7
REGULATORY .............................................................................. 8
1 Revision History
Date
Document revision
2014/05/27
1.0
Change Description
Initial release
2 Product Overview
The J20H086 802.11a/b/g/n 2X2 and BT4.0+LE module provides wireless modem
functionality utilizing direct sequence spread spectrum and OFDM/CCK technology. This
module is based on MTK MT7662U solution .It fully complies with IEEE 802.11n,IEEE
802.11 a/b/g, Bluetooth v2.1+EDR,
V4.0 standard, offering feature-rich wireless connectivity at high standards, and delivering
reliable, cost-effective throughput from an extended distance. Optimized RF architecture
and baseband algorithms provide superb performance and low power consumption.
Intelligent MAC design deploys a high efficient DMA engine and hardware data processing
accelerators which offloads the host processor.
2.1 Application scope
The wireless LAN is compliant to IEEE 802.11n,IEEE 802.11 a/b/g standards.
Channel Spacing
2.4GHz -> 5MHz, 5GHz-> 20MHz (BW on 20MHz),40MHz (BW on 40MHz)
Data rate:
1, 2, 5.5, 11Mbps for 802.11b;
6, 9, 12, 18, 24, 36, 48 and 54Mbps for 802.11a/g;
MCS0(6.5Mbps)~MCS7(72.2Mbps) for 802.11n HT20 mode (single chain);
MCS0(13Mbps)~MCS15(144.4Mbps) for 802.11n HT20 mode (dual chains);
MCS0(13Mbps)~MCS7(150Mbps) for 802.11n HT40 (5G only) mode (single chain);
MCS0(26Mbps)~MCS15(300Mbps) for 802.11n HT40 (5G only) mode (dual chains);
BT:
The BT Module is compliant to Bluetooth 4.0 and EDR standard:
Carrier Frequency: 2402MHz ~ 2480 MHz
Carrier Spacing: 1.0MHz (classic), 2MHz (LE)
Duplexing: TDD
Modulation: FHSS
1Mbps (GFSK), 2Mbps (π/4-DQPSK), 3Mbps (8DPSK),LE (GFSK)
3 Module Hardware Overview
3.1 Features
♦
♦
♦
♦
♦
♦
IEEE802.11a/b/g/n/ac (2X2) based on MTK MT7662U solution.
Support BT4.0+LE
USB 2.0 Interface, High and Full Speeds supported.
Module is powered by the host with a 3.3V +/- 5% supply.
External PCB printed antennas.
4 layers through hole PCB design with FR4 material
3.2 Interface and Connector
♦ Pin definition:
♦ Vendor: JST
♦ Vendor P/N: SM15B-GHS-TB
Pin Number
Symbol Name
UART_RX
UART_TX
GND
RST_L
WOW_H
Status
Input
Output
Input
Output
WOBT_H
Output
GND
Pin definition
UART_RX for BT
UART_TX for BT
Ground
“L”-drive reset signal input from Host.
Wake on WLAN signal output.
“H”-drive is hoped when awake Host.
Wake on Bluetooth signal output.
“H”-drive is hoped when awake Host.
(old: Host_wake)
Ground
8
10
11
12
13
14
15
S1
S2
DM
DP
GND
VSYNC
GND
GND
VCC
VCC
I/O
I/O
Input
PWR
PWR
USB_DATAUSB_DATA+
Shield Ground
3D Video sync Signal
Ground
Ground
DC 3.3V
DC 3.3V
Ground
Ground
3.3 PCB Assembly Dimension
Dimension (W x Lx H ): 80mmx25mmx1.0mm
PCB: 4 layer FR4 design
4 Regulatory
Industry Canada statement:
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation.
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux
appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions
suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce
dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de
provoquer un fonctionnement indésirable.
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour
un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un
minimum de 20 cm de distance entre la source de rayonnement et votre corps.
This device is intended only for OEM integrators under the following conditions:
(For module device use)
1) The antenna must be installed such that 20 cm is maintained between the antenna and
users, and
2) The transmitter module may not be co-located with any other transmitter or antenna.
As long as 2 conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions
suivantes: (Pour utilisation de dispositif module)
1) L'antenne doit être installée de telle sorte qu'une distance de 20 cm est respectée entre
l'antenne et les utilisateurs, et
2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.
Tant que les 2 conditions ci-dessus sont remplies, des essais supplémentaires sur
l'émetteur ne seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours
responsable des essais sur son produit final pour toutes exigences de conformité
supplémentaires requis pour ce module installé.
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations
or co-location with another transmitter), then the Canada authorization is no longer
considered valid and the IC ID can not be used on the final product. In these
circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate Canada authorization.
NOTE IMPORTANTE:
Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines
configurations d'ordinateur portable ou de certaines co-localisation avec un autre
émetteur), l'autorisation du Canada n'est plus considéré comme valide et l'ID IC ne peut
pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur OEM sera chargé
de réévaluer le produit final (y compris l'émetteur) et l'obtention d'une autorisation distincte
au Canada.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be
installed such that 20 cm may be maintained between the antenna and users. The final
end product must be labeled in a visible area with the following: “Contains IC:
2878D-J20H086”.
Plaque signalétique du produit final
Ce module émetteur est autorisé uniquement pour une utilisation dans un dispositif où
l'antenne peut être installée de telle sorte qu'une distance de 20cm peut être maintenue
entre l'antenne et les utilisateurs. Le produit final doit être étiqueté dans un endroit visible
avec l'inscription suivante: "Contient des IC: 2878D- J20H086".
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding
how to install or remove this RF module in the user’s manual of the end product which
integrates this module.
The end user manual shall include all required regulatory information/warning as show in
this manual.
Manuel d'information à l'utilisateur final
L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final
quant à la façon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur
du produit final qui intègre ce module.
Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises
et avertissements comme indiqué dans ce manuel.
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna
and users, and 2) The transmitter module may not be co-located with any other transmitter
or antenna.
As long as 2 conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed
IMPORTANT NOTE: In the event that these conditions can not be met (for example
certain laptop configurations or co-location with another transmitter), then the FCC
authorization is no longer considered valid and the FCC ID can not be used on the
final product. In these circumstances, the OEM integrator will be responsible for
reevaluating
the end product (including the transmitter) and obtaining a separate FCC
authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be
installed such that 20 cm may be maintained between the antenna and users. The
final end product must be labeled in a visible area with the following: “Contains FCC
ID: MCLJ20H086”. The grantee's FCC ID can be used only when all FCC compliance
requirements are met.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the end
product which integrates this module.
The end user manual shall include all required regulatory information/warning as show
in this manual.
For Taiwan 警語： (電信管制射頻器材使用)
經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻
率、加大功率或變更原設計之特性及功能。
低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立
即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線
電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之
干擾。
Note: 1. 本模組於取得認證後將依規定於模組本體標示審驗合格標籤 2. 系統廠商應於平
台上標示「本產品內含射頻模組: XXXyyyLPDzzzz-x (NCC ID) 」字樣
Europe – EU Declaration of Conformity
This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been
applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC:
‐ EN 60950‐1: 2006+A11:2009+A1:2010+A12:2011
Safety of Information Technology Equipment
‐ EN 62311: 2008
Assessment of electronic and electrical equipment related to human exposure restrictions for electromagnetic fields (0
Hz‐300 GHz)
(IEC 62311:2007 (Modified))
EN 300 328 V1.9.1
‐ Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband Transmission systems; Data transmission
10
equipment operating in the 2,4 GHz ISM band and using spread spectrum modulation techniques; Harmonized EN covering
essential requirements under article 3.2 of the R&TTE Directive
EN 301 489‐1 V1.8.1: 2008
Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio
equipment and services; Part 1: Common technical requirements
EN 301 489‐17 V2.1.1 2009
Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio
equipment and services; Part 17: Specific conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance
RLAN equipment
National Authorities were informed according to Article 6.4 of Frequency Notification.
Special Requirements are considered. The product is labeled with CE Marking.
11

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Copy, Extract
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2015:07:17 12:05:47+08:00
Create Date                     : 2015:07:15 19:39:44+08:00
Metadata Date                   : 2015:07:17 12:05:47+08:00
Format                          : application/pdf
Title                           : Microsoft Word - J20H086.01_User_Manual
Creator                         : eku
Producer                        : Acrobat Distiller 8.1.0 (Windows)
Document ID                     : uuid:73486913-f95f-4535-9662-80bbb321cee4
Instance ID                     : uuid:90123756-ca2d-40dd-9d11-e631ce4b4527
Page Count                      : 11
Author                          : eku

EXIF Metadata provided by EXIF.tools