HON HAI PRECISION IND J27H020 O3 WiFi Module User Manual We

HON HAI Precision Ind. Co., Ltd. O3 WiFi Module We

Contents

OEM installation guide

HON HAI PRECISION IND. CO., LTD. HSINCHU SCIENCE PARK BRANCH OFFICE O3 WIFI MODULE J27H020 USER’S MANUAL
HON HAI PRECISION IND. CO., LTD. HSINCHU SCIENCE PARK BRANCH OFFICE Contents INTRODUCTION ................................................................................................................................................................... 3 1.1 WLAN FEATURES .......................................................................................................................................................... 3 1.2 FCC NOTICE .................................................................................................................................................................. 4 1.3 CANADA NOTICE ............................................................................................................................................................ 5 The information contained in this manual has been verified at the time of this manual printing. The manufacturer reserves the right to make any changes and improvements in the product described in this manual at any time and without notice. All registered trademarks are the property of their respective owners.
HON HAI PRECISION IND. CO., LTD. HSINCHU SCIENCE PARK BRANCH OFFICE Introduction O3 WIFI Module is compliance with IEEE802.11,IEEE 802.11b and IEEE 802.11g Standards. 1.1 WLAN Features Operating Frequency 2400 ~ 2483.5 MHz ISM band Modulation Schemes 802.11: DPSK, DBPSK 802.11g: OFDM, DQPSK, DBPSK and CCK 802.11b: DQPSK, DBPSK and CCK Channel Numbers IEEE 802.11 compliant: 1 ~ 13 channels for United States, Europe and Japan IEEE 802.11b/g compliant: 1 ~ 11 channels for United States 1 ~ 13 channels for Europe, Japan WLAN Data Rate 802.11g: Up to 54 Mbps with auto fallback to 48, 36, 24, 18, 12, 9 and 6 Mbps. 802.11b: Up to 11 Mbps with auto fallback to 5.5, 2 and 1Mbps. 802.11 legacy: Up to 1Mbps and 2Mbps Media Access Protocol CSMA/CA with ACK Transmitter Output Power Item Condition Min Typ. Max Unit Transmit power level 802.11 legacy 1Mbps -1.5 0 1 dBm 2Mbps -1.5 0 1 dBm 802.11g 6Mbps 3.5 5 6 dBm 9Mbps 3.5 5 6 dBm 12Mbps 3.5 5 6 dBm 18Mbps 3.5 5 6 dBm 24Mbps 3.5 5 6 dBm 36Mbps 2.5 4 5 dBm 48Mbps 2.5 4 5 dBm
HON HAI PRECISION IND. CO., LTD. HSINCHU SCIENCE PARK BRANCH OFFICE 54Mbps 2 3.5 4.5 dBm 802..11b 1Mbps 4 5.5 6.5 dBm 2Mbps 4 5.5 6.5 dBm 5.5Mbps 4 5.5 6.5 dBm 11Mbps 4 5.5 6.5 dBm Antenna Type Single antenna connector for off board antenna; Operating Voltage 1.8 VDC and 3.3 VDC Operating Systems Windows 98/Me/2000/XP 1.2 FCC Notice Federal Communication Commission Interference Statement : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. FOXCONN declared that J27H020 802.11b/g module is limited in CH1~11 from 2412 to 2462 MHz by specified firmware controlled in USA. This device is intended only for OEM integrators under the following conditions: The antenna must be installed such that 20 cm is maintained between the antenna and users, and The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid
HON HAI PRECISION IND. CO., LTD. HSINCHU SCIENCE PARK BRANCH OFFICE and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labelling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labelled in a visible area with the following: “Contains FCC ID: MCL J27H020. Manual Information That Must be Included The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrate this module. The users manual for OEM integrators must include the following information in a prominent location “IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. 1.3 Canada Notice Industry Canada Statement: Operation is subject to the following two conditions: 1) This device may not cause interference. 2) This device must accept any interference, including interference that may cause undesired operation of the device. To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.

Navigation menu