HON HAI PRECISION IND MICA2 WIFI 11A/N MODULE User Manual EN manual Redacted parts 0524

HON HAI Precision Ind. Co., Ltd. WIFI 11A/N MODULE EN manual Redacted parts 0524

Contents

EN_manual

14ComponentsWii U ControllerFront side L Control Stick (L Stick Button*)* Works when pressing the L Control Stick in. + Control Pad Sensor BarDetects the movement of Wii Remote. Camera A / B / X / Y Button R Control Stick (R Stick Button*)* Works when pressing the L Control Stick in. + / START Button - / SELECT Button Spealer (L · R) POWER ButtonPress to turn the console ON or OFF (씮Page XX).
15Components Battery LED It shows the status of battery charging and remaining power of the battery (씮Page XX). (Light in orange) : Charging (Light in red) : Battery power is low (Blinking in red) : Battery power is very low HOME buttonShows menu (HOME button menu) that can setup Wii U Controller or Wii Remote, or see electronic manual(씮Wii U electronic manual " menu").Lights in blue when you receive notices or informations from your friend. Lights will turn off when pressing . Microphone Touch screen NFCHow to use the touch screenTouchTouch the screen softly.* If the touch screen does not work correctly, adjust the touch screen on hardware settings (씮Page XX). If you cannot operate correctly on Wii U menu, use + Control Pad and .SlideMove while touching the screen.thisthe
16ComponentsAbove sideBack sideBottom side
17Components L / ZL button R / ZR button Stylus holderPut the attached stylus in. VolumeSlide to adjust the volume of Wii U Controller. Infrared transceiverSends and receives information when using infrared communication. Audio jack For connection of stereo headphones. If headphones are connected, no sound will play through the speakers. AC adapter connectorAllows connection to the AC adapter for Wii U controller. Battery coverBattery is installed inside. * Do not remove the cover unless you need to replace the battery. SYNCRO Button (SYNC)Used when synchronizing with the console.* Wii U Controller included on the Wii U hardware set is already syncronized. Cradle holder (tentative)Place the controller on the top of the charging cradle(*), and it will click into place. Charging connectorCharging will start when the controller touches the charging connector on the charging cradle(*). External extension connectorAllows you to connect external extension equipment for Wii U controller.thisthisThis hardware set is already syncronized.this
22Turning the power ON/OFFTurning the power ON/OFFTurn the power ON/OFF by using Wii U console or Wii U controller. After turning the power ON, sekect the account and Wii U menu will show up. (tentative)* Power can be turned ON/OFF by the other accessories (Wii Remote or Wii U grip controller) that is synchronized to the Wii U console.Turn the power ONTurn the power ON by using of Wii U controllerWhen pressing , power will be ON and the screen of the Wii U controller will be displayed.Turn the power ON by using of Wii U consoleWhen pressing on Wii U console, power will be turned ON and the screen of the Wii U controller will be displayed, same as in the of Wii U controller.Energy-saving modeDepending on the images that is displayed, brightness and the colors are automatically adjusted, and the battery will last longer (씮Wii U electronic manual “ menu”)* When purchasing, this feature is turned OFF.the thetheconsole.thecontroller will be displayed.thisthethis controller will be displayed, same as in thethethe controllerthe console
23Turning the power ON/OFFTurning the power OFFWhen turning OFF using Wii U controller, press for approximately one second. When the power is turned OFF, battery LED on Wii U console will light in red.* Even though the power is turned OFF, battery LED will not be switched off.Automatic power-OFF featureWhen nothing is operated while certain time, console will be turned OFF when this feature is ON (씮Wii U menu “Automatic power-OFF” on “Hardware settings”).* When purchasing, this feature is turned OFF.Display OFFWhen the Wii U controller screen is not used, screen can be turned OFF and save the battery (씮Wii U electronic manual “ menu”)thetheWhen the controller screen is not used, screen can be turned OFF and save the battery
FCC Compliance Statements Caution: Any changes or modifications not expressly approved by the party responsible for product compliance could void the user's authority to operate the equipment. This device must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help
Canadian Compliance Statement Complies with the Canadian ICES-003 Class B specifications. Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada. This device complies with RSS 210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of this device. (1) il ne doit pas produire de brouillage et (2) l’ utilisateur du dispositif doit étre prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropic radiated power (EIRP) is not more than that required for successful communication.Wireless Radio Use This device is operated in 5180~5240MHz (indoor only) and 5745~5825MHz.

Navigation menu