HON HAI PRECISION IND T60M665 Bluetooth Wireless Card in Notebook PC User Manual Cover

HON HAI Precision Ind. Co., Ltd. Bluetooth Wireless Card in Notebook PC Cover

UserManual.wiki >

HON HAI PRECISION IND >

T60M665 User Manual >

Antenna Specification

Contents

1. users manual
2. Antenna Specification

Antenna Specification

承認書 APPROVAL SHEET 客戶名稱 Customer ：客戶料號 Customer P/N ： 25.90143.001 適用機種 Model No. ： GANNET 送件日期 Submitted Date：承認日期 Approved Date ：瀚宇料號 HannStar P/N ：品名 Description ： APPROVED 承認編號承認人簽章瀚宇電子股份有限公司 HannStar Electronics Corp. 台北縣 242 新莊市化成路 211 巷5號 No. 5, Lane 211, Hua Cheng Rd., Hsin Chuang Taipei Hsien, Taiwan, R.O.C. Tel: 886-2-22779377 Fax: 886-2-2994-4240 http://www.elc.hannstar.com.tw Wistron Corporation September. 05, 2003 WA00101 BLUETOOTH for GANNET system

Prepared: Leo Chong Checked: Angel Lee Approved: Allen Lin Date: May/13’ 03 瀚宇電子股份有限公司 HannStar Electronics Corp. 承認書索引 Index Customer P/N: 25.90143.001 Model: GANNET HSE P/N: WA00101 1. Introduction 2. Revision History 3. Product Spec. 4. Environment Performance Test 5. Package 6. FAI Test 7. VSWR CPK 8. Cable Spec. 9. Connector Spec. 10. PCB 11. SONY T4000

HannStar Electronics Corp. 1. Introduction Antennas for Bluetooth system Bluetooth Antenna (PCB type) 1. Application: Left side in motherboard location 2. Cable length: 150mm, White (IPEX connector with φ1.13mm RF cable) 2. Revision History Date Version Change Description 09/05/2003 A New Release 3. Product Spec. 3.1 Antenna Design Specification Measure environment LCD angle 110 degree 3.1.1 VSWR 2G4 ISM (2.40GHz-2.483GHz) VSWR 2.40GHz 2.45GHz 2.50GHz Bluetooth antenna ≦2 3.1.2 Average gain 2G4 ISM (2.40GHz-2.483GHz) Average Gain 2.40GHz 2.45GHz 2.50GHz Bluetooth Antenna ≧-5 3.2 Mechanical Spec. See the attached drawing Bluetooth Antenna

HannStar Electronics Corp. 3.3 Antenna BOM structure 3.4 Antenna Test Results 3.4.1 VSWR 3.4.2 Radiation Pattern 2G4 ISM (2.40GHz-2.483GHz) Gain(dBi) 2.40GHz 2.45GHz 2.50GHz Peak 1.23 -0.49 0.15 Bluetooth Antenna Average -4.08 -4.19 -4.47 NO. Part NO. Description Q’ty 1 U011-002-0013-2 Hitachi Cable O1.13 White 150mm 1 2 U010-007-0059 PCB 5x15mm 1 3 U006-002-0010 I-PEX Connector 1 4 U013-011-0026 Type SONY T4000 1 2G4 ISM (2.40GHz-2.483GHz) VSWR 2.40GHz 2.45GHz 2.50GHz Bluetooth Antenna 1.1218 1.1227 1.1244

HannStar Electronics Corp. Bluetooth Antenna @- 2.40 GHz Bluetooth Antenna @- 2.45 GHz

HannStar Electronics Corp. Bluetooth Antenna @- 2.483 GHz 0° 90° 180° Bluetooth Antenna

HannStar Electronics Corp. 4. Environment Performance Test 4.1 Introduction This EQT (Environment Qualification Test) report is used to describe the final status of PCB type Antenna about the EQT test results. 4.2 Test Items and Results 4.2.1 the following table is used to show the final status of PCB type Antenna. Test Item Specification Test Result Tested By Remark Thermal Shock Temperature range:-20℃~80℃ Hold Time:30 min Total cycle:20 cycles Pass HSE Vibration (Need NB) Frequency 5 to 500Hz Overall rms level : 0.6G P-P~2.0G P-P Duration of test : 1 Hr/cycle Number of axes : X,Y,Z 1 cycle/axis Pass HSE Salt Spray Chamber temperature : 35℃ Salt : 5% Hold time : 48 Hr Pass HSE Contact Engagement & Separation Forces Speed : 22 mm/mint Inspection Item : Soldering Pull strength Soldering pull strength > 1 kgw Pass HSE 2G4 ISM (2.40GHz-2.483GHz) VSWR S/N 2.40GHz 2.45GHz 2.50GHz 01 1.1218 1.1227 1.1244 02 1.1352 1.1312 1.1364 Before Thermal Shock Test 03 1.3122 1.1532 1.2123 01 1.5623 1.4313 1.6325 02 1.5325 1.3256 1.5421 After Thermal Shock Test 03 1.4562 1.4121 1.5213 270°

HannStar Electronics Corp. 5. Package See the attached drawing. Bluetooth Antenna 2G4 ISM (2.40GHz-2.483GHz) VSWR S/N 2.40GHz 2.45GHz 2.50GHz 01 1.21 1.23 1.22 02 1.25 1.26 1.28 Before Vibration Test 03 1.13 1.11 1.16 01 1.46 1.35 1.50 02 1.48 1.45 1.55 After Vibration Test 03 1.54 1.50 1.61 Bluetooth Antenna (Right) 2G4 ISM (2.40GHz-2.483GHz) VSWR S/N 2.40GHz 2.45GHz 2.50GHz 01 1.25 1.23 1.26 02 1.16 1.12 1.13 Before Salt Spray Test 03 1.19 1.17 1.18 01 1.50 1.44 1.48 02 1.45 1.46 1.42 After Salt Spray Test 03 1.50 1.49 1.53 Main Antenna (Right) Number 1 2 3 Max Min Avg Soldering Pull strength (Unit:kg) 3.985 3.957 3.967 3.985 3.957 3.696

適用客戶類別二.紙箱包裝方式:一.成品包裝方式:包裝作業說明:包裝作業標準適用產品核定:制定:覆核:編號:包裝類別 Tray 盤版次:修訂日期:頁次:制定日期:備註: 0100紙箱1Wireless Lan蔡麗文圖一Tray盤420個TRAY盤上蓋圖二用膠帶纏繞一圈裝入紙箱注意事項:1.包裝前請確認成品無夾帶綿絮或污染物.2.包裝時不得有毀損以及污染成品之情形發生.3.包裝時必須注意成品與包材之方向性,不得有方向錯誤之情形發生.4.TRAY是否有變形破裂情況發生.5.TRAY和TRAY結合是否有過緊或鬆脫情況發生.隔板2國內一般客戶 90.07.10P899-T007隔板每個TRAY盤共裝15PCS 成品,每小格放3PCS,方向如圖(一)所示.每疊20個TRAY盤,最上層用一個空TRAY做上蓋再用膠帶將TRAY纏繞一圈,以防圖(三)所示.片隔板.蓋上箱子用膠帶封面貼上標籤紙一張箱部分,出貨物填滿. 如圖盤小邊脫落,如裝箱前,先放一片隔板在圖三時須以每疊成品300PCS,中間須以隔板分開,如圖示(四)所示,完成後封箱前再放一緩衝旋轉堆疊圖四隔板(二)所示.箱底,放入成品二疊合,在側如有零32

25.90117.001HSEDate:Yuhina Antenna Leo Manufacturing Site:HSEGauge#/Unit:游標卡尺 (mm)AAllen LinGauge/Unit:尺(mm)Inspection PrecisionITEMLOCATIONNOMINAL +TOL -TOL123123MeanUPPERLOWERHIGHLOWMethod of Gauge1150.0 2.5 2.5 151.0 150.0 149.0 -0.05 0.05 0150.00 40% 40% 尺1mm215.0 0.2 0.2 15.1 14.9 15.100 -0.1 0-0.02 15.03 50% 50% 游標卡尺 0.01mm35.0 0.2 0.2 5.12 5.11 4.99 -1 1 1 5.07 60% 5% 游標卡尺 0.01mm41.00.050.050.970.980.980.01-0.02-0.051.00%60% 游標卡尺0.01mm DrawingDRAWING SPECIFICATIONSINSPECTION RESULTSINSPECTION ANALYSISSample Number Deviation from Nominal % Tolerance Acc/RejProduction Line:FAI DATA SHEETDrawing Number: Supplier :2003/5/16Revision: Approved by:Part Description: Inspected by:ECN NO. ECN BY.REV.876AB541 2 3ACDF.X ±APPD:DR:NONECHKD:UNIT:SCALE:mm (inch).XX ±REV:SHEET: This drawing contains information that is proprietary to HannStar Electronics Corp. And should not be used without written permisson.ECDFED001-980729EB0.30.2

7. VSWR CPK Cpk of AntennaPart Number:25.90019.001Measurement ValueItem Spec. Torance + Torance - 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25VSWR (b) 2.00 0 0 1.32 1.42 1.36 1.52 1.42 1.48 1.36 1.54 1.63 1.57 1.36 1.29 1.38 1.54 1.27 1.43 1.55 1.38 1.37 1.25 1.31 1.45 1.46 1.43 1.4526 27 28 29 30 31 32 33 34 351.49 1.39 1.33 1.48 1.47組界 51.25 1.33 1.40 1.48 1.55 1.63 1.7126 27 28 29 30 31 32 33 34 35組界26 27 28 29 30 31 32 33 34 35組界組界Engineering Specification工程尺寸VSWR (b)工程規格 Product spec 1.5000 1.7500 VSWR (b )正公差 Tolerence 0.5000 0.7500負公差 Tolerence 0.5000 0.7500工程上限 USL 22.5工程下限 LSL 1 1Actual Data量測尺寸VSWR (b)平均數 X bar 1.4233標準差 Sigma 0.0940中間值 Median 1.4250 VSWR (a)眾數 Mode 1.3600 最大值 Max 1.6300最小值 Min 1.25001 Sigma 1.5173UCL 2 Sigma 1.61133個標準差 3 Sigma 1.70521 Sigma 1.3294LCL 2 Sigma 1.2354 組別次數組別次數組別次數 Remark:3個標準差 3 Sigma 1.1414 1.29 1###### 0 ##### 0 Gauge: Dimension C雙邊CP 1.77 1.36 5###### 0 ##### 0單邊CPL 1.50 1.44 7###### 0 ##### 0單邊CPU 2.05 1.52 10 ###### 0 ##### 0製程能力單邊CP 1.50 1.59 5###### 0 ##### 0Ca 0.00 1.67 2###### 0 ##### 0Cpk 1.77 1.74 0###### 0 ##### 0VSWR B C0246810121.29 1.36 1.44 1.52 1.59 1.67 1.740001110.00 0.00 0.00 0.00 0.00 0.00 0.000001110.00 0.00 0.00 0.00 0.00 0.00 0.00第 1 頁

z Cable – Hitachi

z I-PEX Connector

I-PEX CO.,LTD sheet 1 of 9 PRODUCT SPECIFICATION 製品規格 No. PRS-1180 MHF series micro coaxial connector (at 6GHz) Qualification Test Report No. TR-1037 2 S2031 K.O May/17/’02 K.K Prepared by Reviewed by Approved by 1 S1063 K.O Dec/25/’01 K.K 0 S1055 K.O Nov/16/’01 REV. ECN BY DATE APP. REVISION RECORD K.Ohbayashi Nov/16/’01 E.Kawabe Nov/20/’01 K.Katabuchi Nov/21/’01 Form Rev. 0

I-PEX CO.,LTD sheet 2 of 9 DOCUMENT CLASSIFICATION TITLE No. Product Specification MHF series micro coaxial PRS-1180 製品規格 connector 1. Scope ／序言 MHF series micro coaxial connector is a wire to board connector for AWG#32 coaxial cable . MHF series micro coaxial connector は、ＡＷＧ＃３２同軸ケーブルの基板対ワイヤーコネクタである。 2. Objectives ／目的 This specification covers the requirements for product performance and test methods of MHF series microcoaxial connector 本規格は、MHF series micro coaxial connector の性能と試験条件について規定する。 3. Part No. , construction , material and finish ／構成、材料及び仕上げ (1) Part No. Plug : 20278-101R-13, 20278-111R-13 Receptacle : 20279-001E-01 (2) Construction, material and finish of the connector are covered as each drawings. 構成、材料及び仕上げは、各図面に指定されている通りとする。 4. Applicable cable ／適合ケーブル 4-1 Part No. 20278-101R-13, 20278-111R-13 (1) Description Inner conductor : AWG#32(7/0.08) Silver plating annealed copper wire or silver plating tin-copper alloy Dielectric core : Fluoro-plastics , diameter 0.68(+0.04,-0.02)mm , nominal thickness 0.22mm Outer conductor : 16/4/0.05 , nominal diameter 0.93mm , silver plating annealed copper wire Jacket : Fluoro-plastics , diameter 1.13(+0.08,-0.05)mm , nominal thickness 0.1mm (2) Requirements Characteristic impedance : 50(+2,-2)ohm by TDR method (raise time 40ps) Nominal capacitance: 97 pF/m Conductor resistance of inner conductor at 293K (20℃) : 520 ohm/km MAX. Insulation resistance : 1500 mega-ohm.km MIN. Dielectric withstand voltage : no breakdown at AC1000V for 1 minutes. (1) 構成中心導体：ＡＷＧ＃３２（７／０．０８）,銀メッキ軟銅線または銀メッキすず入り銅線誘電体：フッ素樹脂,外径０．６８（＋０．０４,－０．０２）,標準厚さ０．２２ｍｍ外部導体：１６／４／０．０５,標準外径０．９３mm, 銀メッキ軟銅線ジャケット：フッ素樹脂,外径１．１３（＋０．０８,－０．０５）mm, 標準厚さ０．１ｍｍ (2) 仕様特性インピーダンス：５０±２Ω （ＴＤＲ,ライズタイム４０ｐｓ）標準静電容量：９７ｐＦ／ｍ２９３Ｋ（２０℃）時の中心導体導体抵抗：５２０Ω ／ｋｍ以下絶縁抵抗：１５００ＭΩ ・ｋｍ以上耐電圧：ＡＣ１０００Ｖ・１分間にて絶縁破壊の無い事 5. Ratings ／定格 (1) Rated voltage / 電圧：ＡＣ６０Ｖrms (2) Nominal characteristic impedance／公称特性インピーダンス：５０Ω (3) Frequency / 周波数：ＤＣ～６ＧＨｚ (4) VSWR ：１．３ＭＡＸ．ＤＣ～３ＧＨｚ, １．５ＭＡＸ．３～６ＧＨｚ (5) Service Temperature / 使用温度範囲：２３３～３６３Ｋ（－４０～＋９０℃） Form.Rev.0

I-PEX CO.,LTD sheet 3 of 9 DOCUMENT CLASSIFICATION TITLE No. Product Specification MHF series micro coaxial PRS-1180 製品規格 connector 6. Test methods and performance ／試験及び性能 6-1 Test condition / 試験条件 Unless otherwise specified, all tests and measurements shall be performed under the following conditions in accordance with MIL-STD-202 全ての測定と試験は、MIL-STD-202 に基づき以下の条件で行う。. Temperature / 温度：２８８～３０８Ｋ（１５～３５℃） Humidity / 湿度：４５～７５％ＲＨ 6-2 Sample quantity / 試料数 (1) Insulation resistance / 絶縁抵抗：１０ｐｃｓ． (2) Dielectric withstanding voltage / 耐電圧：１０ｐｃｓ． (3) VSWR ：５ｐｃｓ． (4) Unmating force / 抜去力：１０ｐｃｓ (5) Durability / 耐久性：１０ｐｃｓ． (6) Cable retention force / ケーブル保持力：１０ｐｃｓ． (7) Vibration / 振動：１０ｐｃｓ． (8) Shock / 衝撃：１０ｐｃｓ． (9) Thermal shock / 温度サイクル：１０ｐｃｓ． (10) Humidity / 湿度：１０ｐｃｓ． (11) Salt water spray / 塩水噴霧：１０ｐｃｓ． (12) Solderability / 半田付け性：１０ｐｃｓ． (13) Reflow soldering heat resistance / 半田耐熱性：１０ｐｃｓ． 6-3-1 Electrical / 電気的性能 (1) Contact Resistance / 接触抵抗 A.Testing:Solder the receptacle connector to the test board and mate the plug connector together, then measure the contact resistance as shown in Fig.1 by the four terminal method. Apply the low level condition in accordance with MIL-STD-202, Method 307. Open circuit voltage : 20mV MAX Circuit current : 10mA MAX. (DC or AC1kHz) Contact resistance of inner contact : <resistance of A-E> - <resistance of B-E> Contact resistance of ground contact : <resistance of A-D> - <resistance of B-D> PCBPlugReceptacleCableCABDEFig.1 B.Requirements : Contact resistance of inner contact initial 20 milli-ohm MAX. after testing 25milli-ohm MAX. Contact resistance of ground contact initial 10 milli-ohm MAX. after testing 15milli-ohm MAX. Form.Rev.0

I-PEX CO.,LTD sheet 4 of 9 DOCUMENT CLASSIFICATION TITLE No. Product Specification MHF series micro coaxial PRS-1180 製品規格 connector A.試験法：テスト基板にリセプタクルコネクタを半田付けし、プラグコネクタと嵌合させ、Ｆｉｇ．１のように４端子法にて下記の条件で測定する。 MIL-STD-202 試験法 307 に準拠。開回路電圧：２０ｍＶ以下試験電流：１０ｍＡ（ＤＣもしくはＡＣ１ｋＨｚ）中心導体：＜Ａ－Ｅ間の電気抵抗＞－＜Ｂ－Ｅ間の電気抵抗＞外部導体：＜Ａ－Ｄ間の電気抵抗＞－＜Ｂ－Ｄ間の電気抵抗＞ B.必要条件：中心導体初期２０ｍΩ 以下, 試験後２５ｍΩ 以下外部導体初期１０ｍΩ 以下, 試験後１５ｍΩ 以下 (2) Insulation resistance / 絶縁抵抗 A. Testing : Mate the plug and receptacle connector together, then apply DC 100 V between the inner contact and the ground contact in accordance with MIL-STD-202, Method 302. B.Requirements : Initial 500 Mohm MIN. after testing 100 Mohm MIN. A.試験法：リセプタクル及びプラグコネクタを互いに嵌合させ、中心導体と外部導体の間に DC １００Ｖを印加し、測定する。MIL-STD-202 試験法 302 に準拠。 B.必要条件：初期５００MΩ 以上試験後１００MΩ 以上 (3) Dielectric withstanding voltage / 耐電圧 A. Testing : Mate the receptacle and plug connector together, then apply AC 200 Vrms between the inner contact and the ground contact for a minute in accordance with MIL-STD-202, Method 301. B.Requirements : No creeping discharge, flashover, nor insulator breakdown shall occur. A.試験法：リセプタクル及びプラグコネクタを互いに嵌合させ、中心導体と外部導体の間にＡＣ２００Ｖ(実効値) を一分間印加する。 MIL-STD-202 試験法 301 に準拠。 B.必要条件：沿面放電、空中放電、絶縁破壊等の異常のないこと。 (4) VSWR A. Testing : Measure the VSWR as shown in Fig.3 by the network analyzer. Frequency :100M~6GHz PlugCableFig.3L=100mmNetwork analyzerSMAadaptorPlugTerminationNetwork analyzerReceptacleTerminationSMAadaptorSMAadaptor B.Requirements : Plug1.3 MAX at 0.1~3GHz, . 1.5 MAX at 3~6GHz Receptacle 1.3 MAX at 0.1~3GHz, . 1.4 MAX at 3~6GHz A.試験法：ネットワークアナライザーにて Fig.3 のようにＶＳＷＲを測定する。周波数：１００Ｍ～６ＧＨｚ B.必要条件：Ｐｌｕｇ１．３以下０．１～３ＧＨｚ１．５以下３～６ＧＨｚＲｅｃｅｐｔａｃｌｅ１．３以下０．１～３ＧＨｚ１．４以下３～６ＧＨｚ Form.Rev.0

I-PEX CO.,LTD sheet 5 of 9 DOCUMENT CLASSIFICATION TITLE No. Product Specification MHF series micro coaxial PRS-1180 製品規格 connector (5) Insertion loss / インサーションロス A. Testing : Measure the insertion loss as shown in Fig.5 by the network analyzer. Frequency :100M~6GHz PlugCableLNetwork analyzerSMAadaptorSMAadaptor Fig.5 B.Requirements At 0.1~3GHz L=100mm : –1.0dB MIN. L=200mm : –1.4dB MIN. L=300mm : –1.8dB MIN. L=400mm : –2.1 dB MIN. L=500mm : –2.4 dB MIN. At 3~6GHz L=100mm : –1.6dB MIN. L=200mm : –2.1dB MIN. L=300mm : –2.6dB MIN. L=400mm : –3.0 dB MIN. L=500mm : –3.4 dB MIN. A.試験法：ネットワークアナライザーにて Fig.５のようにインサーションロスを測定する。周波数：１００Ｍ～６ＧＨｚ B.必要条件：周波数１００Ｍ～３ＧＨｚ L=100mm : –1.0dB MIN. L=200mm : –1.4dB MIN. L=300mm : –1.8dB MIN. L=400mm : –2.1 dB MIN. L=500mm : –2.4 dB MIN. 周波数３～６ＧＨｚ L=100mm : –1.6dB MIN. L=200mm : –2.1dB MIN. L=300mm : –2.6dB MIN. L=400mm : –3.0 dB MIN. L=500mm : –3.4 dB MIN. 6-3-2 Mechanical / 機械的性能 (1)Unmating force / 挿抜力 A. Testing : Unmate the receptacle connector ( soldered to the test board) and plug at a speed 25±3mm/minutes along the mating by the push-on/pull-off machine . B.Requirements : Total unmating force : Initial 5N MIN. after 30 cycles 3N MIN. Unmating force of inner contact : Initial 0.15N MIN. after 30 cycles 0.1N MIN A.試験法：挿抜試験機を用いて、基板に半田付けしたリセプタクルとプラグを嵌合軸と平行に毎分２５±３ｍｍの速度で挿抜する。 B.必要条件：初回抜去力：５Ｎ以上 ,３０回後抜去力３Ｎ以上中心導体：初回抜去力０．１５Ｎ以上 ,３０回後抜去力０．１Ｎ以上 (2) Durability / 耐久性 A. Testing : Mate and umate the receptacle connector ( soldered to the test board) and plug 30 cycles at a speed 25±3mm/minutes along the mating by the push-on/pull-off machine . B.Requirements : Contact resistance of inner contact initial 20 milli-ohm MAX. after testing 25milli-ohm MAX. Contact resistance of ground contact initial 10 milli-ohm MAX. after testing 15milli-ohm MAX. A.試験法：挿抜試験機を用いて、基板に半田付けしたリセプタクルとプラグを嵌合軸と平行に毎分２５±３ｍｍの速度で３０回挿抜する。 B.必要条件中心導体接触抵抗：初期２０ｍΩ 以下, 試験後２５ｍΩ 以下外部導体接触抵抗：初期１０ｍΩ 以下, 試験後１５ｍΩ 以下 Form.Rev.0

I-PEX CO.,LTD sheet 6 of 9 DOCUMENT CLASSIFICATION TITLE No. Product Specification MHF series micro coaxial PRS-1180 製品規格 connector (3) Cable retention force / ケーブル保持力 A. Testing : Apply force on the cable as shown in Fig.2. During the testing, run 100mA DC to check electrical discontinuity 4NFig.2PCBPlugReceptacleCable2N2N B.Requirements Appearance : Looseness between the parts, chipping, breakage or other abnormality shall not occur. Electrical discontinuity : No electrical discontinuity grater than 1 micro-sec. shall occur. Contact resistance of inner contact initial 20 milli-ohm MAX. after testing 25milli-ohm MAX. Contact resistance of ground contact initial 10 milli-ohm MAX. after testing 15milli-ohm MAX. A.試験法：Ｆｉｇ．２のようにケーブルに力を加える。尚、試験中にＤＣ１００ｍＡの電流を流して電気的瞬断を確認する。 B.必要条件外観：部品のゆるみ、欠け、割れ、その他外観上の異常の無いこと。電流瞬断：試験中、1マイクロ秒を超える電気的瞬断の無いこと。中心導体接触抵抗：初期２０ｍΩ 以下, 試験後２５ｍΩ 以下外部導体接触抵抗：初期１０ｍΩ 以下, 試験後１５ｍΩ 以下 (4) Vibration / 振動 A. Testing : Apply the following vibration to the mating connector . During the testing, run 100mA DC to check electrical discontinuity. Frequency : 10Hz → 100Hz → 10Hz / approx 15 minutes. Half amplitude ,Peak value of acceleration: 1.5mm or 59m/s2 (6G) Directions , cycle : 3 mutually perpendicular direction , 5 cycles(approx 75min )about each direction B.Requirements Appearance : Looseness between the parts, chipping, breakage or other abnormality shall not occur. Electrical discontinuity : No electrical discontinuity grater than 1micro-sec. shall occur. Contact resistance of inner contact initial 20 milli-ohm MAX. after testing 25milli-ohm MAX. Contact resistance of ground contact initial 10 milli-ohm MAX. after testing 15milli-ohm MAX. A.試験法：嵌合状態のコネクタを、下記の振動を加える。尚、試験中にＤＣ１００ｍＡの電流を流して電気的瞬断を確認する。周波数：１０Ｈｚ→１００Ｈｚ→１０Ｈｚ／約１５分間片振幅,加速度：１．５ｍｍｏｒ５９ｍ／ｓ2 （６Ｇ）方向,サイクル：3つの互いに直角な方向について各５サイクル（約７５分）実施 B.必要条件外観：部品のゆるみ、欠け、割れ、その他外観上の異常の無いこと。電流瞬断：試験中、1マイクロ秒を超える電気的瞬断の無いこと。中心導体接触抵抗：初期２０ｍΩ 以下, 試験後２５ｍΩ 以下外部導体接触抵抗：初期１０ｍΩ 以下, 試験後１５ｍΩ 以下 Form.Rev.0

I-PEX CO.,LTD sheet 7 of 9 DOCUMENT CLASSIFICATION TITLE No. Product Specification MHF series micro coaxial PRS-1180 製品規格 connector (5) Shock / 衝撃 A. Testing : Apply the following vibration to the mating connector in accordance with MIL-STD-202, Method 213, Condition B. During the testing, run 100mA DC to check electrical discontinuity. Peak value of acceleration: 735m/s2 (75G) Duration : 11msec Wave Form : half sinusoidal Directions , cycle : 6 mutually perpendicular direction , 3 cycles about each direction B.Requirements Appearance : Looseness between the parts, chipping, breakage or other abnormality shall not occur. Electrical discontinuity : No electrical discontinuity grater than 1 micro-sec. shall occur. Contact resistance of inner contact initial 20 milli-ohm MAX. after testing 25milli-ohm MAX. Contact resistance of ground contact initial 10 milli-ohm MAX. after testing 15milli-ohm MAX. A.試験法：嵌合状態のコネクタを、衝撃試験機に取り付け、下記の衝撃を加える。尚、試験中にＤＣ１００ｍＡの電流を流して電気的瞬断を確認する。MIN-STD-202 試験法 213 試験条件 Bに準拠。最大加速度：７３５ｍ／ｓ２（７５Ｇ）標準持続時間：１１ｍｓｅｃ．波形：半波正弦波方向：直交する６方向、各３回 B.必要条件外観：部品のゆるみ、欠け、割れ、その他外観上の異常の無いこと。電流瞬断：試験中、1マイクロ秒を超える電気的瞬断の無いこと。中心導体接触抵抗：初期２０ｍΩ 以下, 試験後２５ｍΩ 以下外部導体接触抵抗：初期１０ｍΩ 以下, 試験後１５ｍΩ 以下 6-3-3 Environmental / 耐環境性 (1) Thermal shock/ 温度サイクル A. Testing : Apply the following environment to the mating connector . Temperature ,duration :233K/30minutes→278~308K/5minutes MAX.→363K/30minutes→278~308K/5minutes MAX. (-40℃) (5~35℃) (90℃) (5~35℃) No. of cycles : 5 cycles B.Requirements Appearance : Looseness between the parts, chipping, breakage or other abnormality shall not occur. Contact resistance of inner contact initial 20 milli-ohm MAX. after testing 25milli-ohm MAX. Contact resistance of ground contact initial 10 milli-ohm MAX. after testing 15milli-ohm MAX. Insulation resistance : initial 500 mega-ohm MIN. after testing 100 mega-ohm MIN. A.試験法：嵌合状態のコネクタを、下記の雰囲気に放置する。１サイクルの条件：２３３Ｋ／３０分→２７８～３０８Ｋ／５分以下→３６３Ｋ／３０分→２７８～３０８Ｋ／５分以下（－４０℃）（５～３５℃）（９０℃）（５～３５℃）実施サイクル：５サイクル B.必要条件外観：部品のゆるみ、欠け、割れ、その他外観上の異常の無いこと。中心導体接触抵抗：初期２０ｍΩ 以下, 試験後２５ｍΩ 以下外部導体接触抵抗：初期１０ｍΩ 以下, 試験後１５ｍΩ 以下絶縁抵抗：初期５００MΩ 以上試験後１００MΩ 以上 Form.Rev.0

I-PEX CO.,LTD sheet 8 of 9 DOCUMENT CLASSIFICATION TITLE No. Product Specification MHF series micro coaxial PRS-1180 製品規格 connector (2) Humidity / 湿度 A. Testing : Apply the following environment to the mating connector in accordance with MIL-STD-202, Method 103, Condition B . Temperature : 313±2 K (40±2℃) Humidity : 90～95%RH Duration : 96 hours B.Requirements Appearance : Looseness between the parts, chipping, breakage or other abnormality shall not occur. Contact resistance of inner contact initial 20 milli-ohm MAX. after testing 25milli-ohm MAX. Contact resistance of ground contact initial 10 milli-ohm MAX. after testing 15milli-ohm MAX. Insulation resistance : initial 500 mega-ohm MIN. after testing 100 mega-ohm MIN. A.試験法：嵌合状態のコネクタを、下記の雰囲気に放置する。MIL-STD-202 試験法 103 条件 Bに準拠。温度：３１３±２Ｋ（４０±２℃）湿度：９０～９５％ＲＨ時間：９６時間 B.必要条件外観：部品のゆるみ、欠け、割れ、その他外観上の異常の無いこと。中心導体接触抵抗：初期２０ｍΩ 以下, 試験後２５ｍΩ 以下外部導体接触抵抗：初期１０ｍΩ 以下, 試験後１５ｍΩ 以下絶縁抵抗：初期５００MΩ 以上試験後１００MΩ 以上 (3) Salt water spray / 塩水噴霧 A. Testing : Apply the following environment to the mating connector in accordance with MIL-STD-202, Method 101, Condition B. Temperature : 308±2 K (35±2℃) Salt water density by weight : 5±1％ Duration : 48 hours B.Requirements : Appearance no abnormality adversely affecting the performance shall occur. A.試験法：嵌合状態のコネクタを、下記の雰囲気に放置する。温度：３０８±２Ｋ（３５±２℃）塩水濃度：５±１％（重量比）時間：４８時間 B.必要条件：外観著しい腐食の無い事。 6-3-4 Solder / 半田付け関連 (1) Solderability / 半田付け性 A. Testing : Dip the solder tine of the contact in the solder bath at 518±5(245±5℃) for 5±0.5 sec. After immersing the tine in the flux of RMA or R type for 5 to 10 seconds in accordance with MIL-STD-202, Method 208. B.Requirements : More than 95% of the dipped surface shall be evenly wet. A.試験法：コンタクトの半田付け部を５１８±５Ｋ（２４５±５℃）の半田漕内に５±０．５秒浸す。フラックスは、RMA 又は R型を使用し 5～10 秒間浸すものとする。MIL-STD-202, 試験法 208 に準拠。 B.必要条件：浸した面積の 95％以上に半田がむらなく付着すること。 (2) Reflow soldering heat resistance / 半田耐熱性 A. Testing : Put on the receptacle connector to PCB , apply the heat 2 cycles as shown in Fig. 4 B.Requirements : Appearance no abnormality adversely affecting the performance shall occur. A.試験法：基板にリセプタクルコネクタを置き、Ｆｉｇ．４の条件で２回リフローを行う。 B.必要条件：機能を損なう変形及び欠陥の無い事。 Form.Rev.0

I-PEX CO.,LTD sheet 9 of 9 DOCUMENT CLASSIFICATION TITLE No. Product Specification MHF series micro coaxial PRS-1180 製品規格 connector 433~473K(160~200℃)1~2 minutes533(260℃)10±0.5 sec.Fig.4Temp.TimeGradient1 ~ 4 K/sec.Gradient-3 ~ - 6 K/sec. Form.Rev.0

z PCB

z Sony T4000

Navigation menu