HON HAI PRECISION IND T77H747 NFC Module User Manual rev 4

Download:
Mirror Download [FCC.gov]
Document ID	3618634
Application ID	oQNVrazIgdK6rtQ3nDPDiA==
Document Description	User Manual rev 4.pdf
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	205.92kB (2574053 bits)
Date Submitted	2017-10-26 00:00:00
Date Available	2017-10-26 00:00:00
Creation Date	2017-10-26 12:01:59
Producing Software	Microsoft® Office Word 2007
Document Lastmod	2017-10-26 16:02:42
Document Title	User Manual rev 4.pdf
Document Creator	Microsoft® Office Word 2007
Document Author:	SherryHsu

COMPANY CONFIDENTIAL
Revision Note
NFC
(Near Field Communication)
NXP NPC300 Module
Project Name
Document Rev.
FOXCONN Part No.
Module Rev.
FRU Part No.
Customer Part No.
FOXCONN Label Rev
NFC (NXP NPC300) Module
5.0
T77H747.10
005
01AX745
SW10K97523
00S0
Prepared by
Reviewed by
Approved by
Bandy.Jiang
Wei.Liao
Chang-Fu Lin
COMPANY CONFIDENTIAL
Revision History
Revision
1.0
2.0
3.0
4.0
5.0
Date
Originator
Comment
2016/01/28 Smile. Ming Initial release
1> Add pin 1 marking for mechanical drawing.
2> Add SM bus support in addition to I2C bus. (in
page 4,5)
3> Add description of pin9 (TX_PWR_REQ) signal
with active high 1.8V level output. (in page 15)
4> Change the PN of antenna connector from
BM05B-ACHSS-A-GAN-ETF(LF)(SN) to BM05B2016/04/20 Bandy.Jiang
ACHKS-A-GAN-ETF(HF)
5> Update material in shielding drawing.
6> Following the latest schematic, update the
material description into BOM
7> Add Tray ID label, Carton label, Pallet label into
label information
8> Update packing information
1> Update Module picture in page 18
2> Update packing information in page 23~24
2016/04/26 Bandy.Jiang
3> Update vendor PN of host interface connector in
page 15
1> Remove R5 from BOM.
2> Change Foxconn project name from T77H747.00
to T77H747.10
3> Change FRU part No. from 00JT548 to
2016/06/24 Bandy.Jiang
01AX745.
4> Based on above change list, update module
picture, BOM, label contents and packing
information.
1> Change Host JST part number from ACHR-05V2016/06/28 Bandy. Jiang
A-S to ACHR-05V-A-K(HF) in page 14
T77H747.10 is made in China,
Manufactured by HongFuJin Precision Industry Co., LTD
Manufacture Site: ChongQing
http://www.foxconn.com
COMPANY CONFIDENTIAL
Content
1. INTRODUCTION ........................................................................................................................................................... 4
1.1 SCOPE ....................................................................................................................................................................... 4
1.2 FUNCTION.................................................................................................................................................................. 4
1.3 HARDWARE BLOCK DIAGRAM ....................................................................................................................................... 5
2. ELECTRICAL CHARACTERISTICS ........................................................................................................................... 6
2.1 OPERATING CONDITIONS .............................................................................................................................................. 6
2.1 HOST INTERFACE CHARACTERISTICS .......................................................................................................................... 7
2.2 POWER-UP SEQUENCE ................................................................................................................................................ 8
2.3 POWER-DOWN SEQUENCE........................................................................................................................................... 9
2.4 FUNCTION TIMING CHARACTERISTICS ......................................................................................................................... 9
3. NFC CONTACTLESS STANDARD CONFORMANCE .......................................................................................... 10
3.1 FREQUENCY INTEROPERABILITY................................................................................................................................ 10
3.2 SUPPORTED SMART CARD TYPES .............................................................................................................................. 10
3.3 CONTACTLESS INTERFACE UNIT ................................................................................................................................ 11
4. MECHANICAL ARCHITECTURE.............................................................................................................................. 12
4.1 MODULE MECHANICAL DRAWING .............................................................................................................................. 12
4.2 ANTENNA INTERFACE OF NFC MODULE .................................................................................................................... 13
4.3. HOST INTERFACE OF NFC MODULE ......................................................................................................................... 15
4.4. SHIELDING COVER OF NFC MODULE ....................................................................................................................... 18
4.5. PICTURE OF NFC MODULE ....................................................................................................................................... 18
5. PCB PATTERN OF NFC MODULE .......................................................................................................................... 19
5.1 PCB COMPONENT PLACEMENT ................................................................................................................................. 19
5.2 PCB STACK UP AND MATERIALS .............................................................................................................................. 19
6. BOM (BILL OF MATERIALS) OF NFC MODULE ................................................................................................... 20
7. MARKING INFORMATION ........................................................................................................................................ 21
8. PACKING INFORMATION ......................................................................................................................................... 23
COMPANY CONFIDENTIAL
1. Introduction
The T77H747.10 is an NFC module designed for integration in computer or portable
equipment and consumer devices compliant with NFC standards (NFC Forum, NCI, ISO/IEC
14443 and ISO/IEC 15693) etc. This module is based on NXP NPC300 solution, which is a
highly integrated transmission module for contactless communication at 13.56MHz.
1.1
Scope
The NFC module RF protocols supported:
•
•
•
•
•
•
•
•
1.2
NFCIP-1, NFCIP-2 protocol
NFC Forum device 1.3
ISO/IEC 14443A, ISO/IEC 14443B
ISO/IEC 15693/ICODE VCD mode
FeliCa PCD mode/PICC mode
MIFARE PCD encryption mechanism(MIFARE 1K/4K)
MIFARE PICC mode
NFC Forum tag (type 1/type 2/type 3/type 4/type V)
Function
•
NFC Features
- Reader & Writer mode
- Peer-to-Peer Communication mode
- Card emulation mode
•
I2C-bus and SM-bus compatible for host Interface
•
Windows 8 Logo Device Requirement compliant
- NFC Forum Wave1 Certification
- LLCP
- SNEP
•
Windows 10 Logo system Requirement compliant
- Peer to Peer Communication over 2cm distance less than 10cm
•
Modular certification
- FCC
- CE
- UL/CB
- meet other regulatory requirements (as defined by 108 countries)
(Remark: Regulatory Certification is not started at this phase)
•
Support Intel Windows 7/8.x/10 platform
•
RoHS and Green Compliant
COMPANY CONFIDENTIAL
1.3 Hardware block diagram
The T77H747.10 NFC module is based on NXP NPC300 solution with includes ARM
microcontroller core, EEPROM, demodulator and decoder, power management unit, host
interface. This module is powered from the host (5V) and interfaces to the host with I 2C -bus
compatible signals, on-board 27.12 MHz XTAL. Also includes on board low profile FPC/FFC
12pin connector for host interface and 5pin WTB antenna connector for antenna interface.
Form factor: 20.0mm x13.0mm x 2.1mm (typical) NFC module
Host Interface: I C and SM bus compatible interface with 12-pin FPC connector
PCB: 4-layers HDI design
The functional block diagram is shown as below:
COMPANY CONFIDENTIAL
2. Electrical Characteristics
2.1 operating conditions
Absolute Maximum Rating
Symbol
VBAT
PVDD
Condition
Respect to GND
Respect to GND
HBM
CDM
----
Min.
----0
-20
Typ.
5.0
3.3
--+25
+25
--
Max
6.0
4.35
+/-1.0
+/-500
+70
+85
+85
Unit
KV
℃
℃
Recommended Operating Condition
Symbol
Condition
VBAT
Respect to GND
PVDD
Respect to GND
PMUVCC
Respect to GND
VDD
Respect to GND
VDD(SIM)
Respect to GND
Min.
4.5
3.0
1.62
1.65
1.62
Typ.
5.0
3.3
1.8
1.8
1.8
Max
5.5
3.6
1.98
1.95
1.98
Unit
ESD Limit Level
Operating Temperature
Storage Temperature
Storage Humidity
Remark: VDD for TX_PWR_REQ referred voltage, VDD(SIM) for SWIO_UICC referred voltage.
Power Consumption
Condition
Power
consumption
Reader mode
(PCD active)
Reader mode
(PCD standby)
Peer to peer mode
(active)
Peer to peer mode
(standby)
Continue TX mode
Hard Power Down mode
Min.
Typ.
Max
Unit
--
130
--
mA
--
50
--
uA
--
130
--
mA
--
50
--
uA
---
130
10
---
mA
uA
COMPANY CONFIDENTIAL
2.1 Host interface characteristics
I2C-bus Interface
The I C-bus Interface implements a slave I C-bus interface with integrated shift register, shift timing generation
and slave address recognition.
I C-bus Standard mode (100 KHz SCL), Fast mode (400 KHz SCL) and High-speed mode (3.4 MHz SCL) are
supported.
I2C-bus timings
Here below are timings and frequency specifications.
High-speed mode I2C-bus timing specification
Symbol
Parameter
fCLK(HIF4)
tLOW
tHIGH
tSU;DAT
tHD;DAT
tr(HIF3)
tf(HIF3)
Clock frequency on pin HIF4
Set-up time for a repeated
START condition
Hold
time(repeated)
START
condition
LOW period of the SCL clock
HIGH period of the SCL clock
Date set-up time
Data hold time
Rise time on pin HIF3
Fall time on pin HIF3
Vhys
Hysteresis voltage
tSU;STA
tHD;STA
Conditions
Min
Max
Unit
I C-bus SCL; Cb<100pF
3.4
MHz
Cb<100pF
160
ns
Cb<100pF
160
ns
Cb<100pF
Cb<100pF
Cb<100pF
C2 b<100pF
I C-bus SDA; Cb<100pF
I C-bus SDA; Cb<100pF
Schmitt
trigger
inputs;
Cb<100pF
160
60
10
10
10
80
80
ns
ns
ns
ns
ns
ns
0.1*VPVDD
Conditions
Min
Max
Unit
Cb<400pF
600
400
KHz
ns
Cb<400pF
600
ns
Cb<400pF
Cb<400pF
Cb<400pF
Cb<400pF
Schmitt
trigger
Cb<400pF
1.3
600
100
0.1* VPVDD
900
ns
ns
ns
ns
Fast mode I2C-bus timing specification
Symbol
Parameter
fCLK(HIF4)
tSU;STA
Clock frequency on pin HIF4
Set-up time for a repeated
START condition
Hold
time(repeated)
START
condition
LOW period of the SCL clock
HIGH period of the SCL clock
Date set-up time
Data hold time
Hysteresis voltage
tHD;STA
tLOW
tHIGH
tSU;DAT
tHD;DAT
Vhys
I C-bus SCL; Cb<400pF
inputs;
COMPANY CONFIDENTIAL
2.2 Power-up sequence
There are 2 different supplies for module which allows set up independently, therefore
different power-up sequences have to be considered.
1> VBAT is set up before PVDD
This is at least the case when VBAT pin is directly connected to the battery and when
module VBAT is always supplied as soon the system is supplied.
As VEN pin is referred to VBAT pin, VEN voltage shall go high after VBAT has been set.
2> PVDD and VBAT are set up in the same time
It is at least the case when VBAT pin is connected to a PMU/regulator which also supplies
PVDD.
COMPANY CONFIDENTIAL
2.3 Power-down sequence
2.4 Function timing characteristics
Reset timing
Symbol
tW(VEN)
tboot
Parameter
VEN pulse width
Boot time
Conditions
To reset
Power-up timings
Symbol
Parameter
Transition time from pin VBAT to
tt(V -VEN)
pin VEN
Transition time from pin PVDD to
tt(V -VEN)
pin VEN
Transition time from pin VBAT to
tt(V -V )
pin PVDD
BAT
PVDD
BAT
PVDD
Power-down timings
Symbol
Parameter
tVBAT(L)
Time VBAT LOW
Download mode timings
Symbol
Parameter
Tt(DWL_REQ-VEN)
Transition
time
from
DWL_REQ to pin VEN
pin
Conditions
VBAT,VEN
Voltage=HIGH
PVDD,VEN
Voltage=HIGH
VBAT,PVDD
Voltage=HIGH
Min
10
Typ
Max
2.5
Unit
us
ms
Min
Typ
Max
Unit
0.5
ms
0.5
ms
0.5
ms
Conditions
Min
20
Typ
Max
Unit
ms
Conditions
DWL_REQ,VEN
voltage=HIGH
Min
Typ
0.5
Max
Unit
ms
COMPANY CONFIDENTIAL
3. NFC contactless standard conformance
3.1 Frequency interoperability
When in communication, NFC module is generating some RF frequencies. It is also sensitive
to some RF signals as it is looking from data in the field.
In order to avoid interference with others RF communication, it is required to tune the
antenna matching for antenna board.
(Remark: The antenna matching tuning is responsible for antenna vendor)
It must limit the RF frequency dispersion to 13.56MHz +/-50ppm.
3.2 Supported smart card types
Read CSN
(Card Serial Number)
Read/Write
application data area
Supported
baud rates
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
106 kbps
106 kbps
212, 424 kbps
106 kbps
106 kbps
Yes
Yes (with application)
106 kbps
Mifare Classics 1K,4K
Yes
Yes (with application)
106 kbps
Mifare DESFire
Yes
Yes (with application)
106 kbps
Mifare Ultralight
Yes
Yes (with application)
106 kbps
Mifare Plus
Yes
Yes (with application)
106 kbps
Yes
Yes (with application)
106 kbps
Yes
Yes (with application)
106 kbps
FeliCa general card
Yes
Yes (with application)
212, 424 kbps
FeliCa Edy card
Yes
Yes (with application)
212, 424 kbps
FeliCa Suica card
Yes
Yes (with application)
212, 424 kbps
FeliCa PKI Option card
Yes
Yes (with application)
212, 424 kbps
HID iCLASS Seos
Yes
Yes (with application)
106 kbps
Card Types
NFC Forum Type1 Tag
NFC Forum Type2 Tag
NFC Forum Type3 Tag
NFC Forum Type4 Tag
NFC Forum TypeV Tag
ISO/IEC 14443 Type
compliance cards
(Mifare) SmartMX
ISO/IEC 14443
compliance cards
Type
10
COMPANY CONFIDENTIAL
3.3 Contactless interface unit
The NFC module supports various communication modes at different transfer speeds and
modulation schemes. The following chapters give more detailed overview of selected
communication modes.
1> Reader/Writer communication modes
Generally 5 reader/writer communication modes are supported:
•
PCD reader/writer for ISO/IEC 14443A/MIFARE
The transfer speed includes 106 kbit/s, 212 kbit/s, 424 kbit/s and 848 kbit/s.
•
PCD reader/writer for ISO/IEC 14443B
The transfer speed includes 106 kbit/s, 212 kbit/s, 424 kbit/s and 848 kbit/s.
•
PCD reader/writer for Jewel/Topaz tags
The transfer speed includes 106 kbit/s, 212 kbit/s, 424 kbit/s and 848 kbit/s.
•
PCD reader/writer for FeliCa cards
The transfer speed includes 212 kbit/s, 424 kbit/s.
•
VCD reader/writer for ISO/IEC 15693/ICODE
The transfer speed includes 1.65 kbit/s, 26.48 kbit/s.
2> Peer to Peer communication modes
(ISO/IEC 18092, Ecma 340 NFCIP-1 communication modes)
An NFCIP-1 communication takes place between 2 devices:
•
•
NFC initiator: generates RF field at 13.56 MHz and starts the NFCIP-1communication.
NFC Target: responds to NFC initiator command either in a load modulation scheme in Passive
communication mode or using a self-generated and self-modulated RF field for Active communication
mode.
The NFCIP-1 communication differentiates between Active and Passive communication
modes.
•
•
Active communication mode means both the NFC initiator and the NFC target are using their own RF field
to transmit data
Passive communication mode means that the NFC target answers to an NFC initiator command in a load
modulation scheme. The NFC initiator is active is terms of generating the RF field.
The NFC module supports the Active Target, Active Initiator, Passive Target and Passive
Initiator communication modes at the transfer speeds 106 kbit/s, 212 kbit/s and 424 kbit/s.
3> Card communication modes
The NFC module can be addressed as an ISO/IEC 14443A or ISO/IEC 14443B cards. This
means that NFC module can generate an answer in a load modulation scheme.
The transfer speed includes 106 kbit/s, 212 kbit/s and 424 kbit/s.
11
COMPANY CONFIDENTIAL
4. Mechanical Architecture
4.1 Module Mechanical Drawing
Dimension (WxL): 20mm x 13mm, Module Max Thickness: 2.2mm
Pin 1
12
COMPANY CONFIDENTIAL
4.2 Antenna interface of NFC module
1> Antenna connector
Manufacturer: JST
Connector Type
Manufacturer PN: BM05B-ACHKS-A-GAN-ETF(HF)
Manufacture PN
Size
ACH connector SMT type with
1.2mm pitch
JST : BM05B-ACHKS-A-GANETF(HF)
7.8mm x 4.3mm x 1.5mm
Connector 2D drawing:
Remark: Dimension Tolerance: +/-0.3mm
Pin definition:
Pin
Symbol
RXP
TX1
GND
TX2
RXN
S1
GND
S2
GND
I/O
Refer
VDD
VDD
N/A
VDD
VDD
N/A
N/A
Note
Positive receiver input
Antenna output1
Ground
Antenna output2
Negative receiver input
Ground
Ground
Remark: P = power supply, G = ground, I = input, O = output, I/O = input/output
13
COMPANY CONFIDENTIAL
2> Recommend Antenna cable design.
14
COMPANY CONFIDENTIAL
4.3. Host interface of NFC module
1> Host interface connector
Manufacturer: KYOCERA
Connector
Manufacturer PN: 046811612000846 +
Manufacture PN
FPC/FFC connector SMT type
with 0.5mm pitch
KYOCERA: 046811612000846+
Size
11.73mm x 4.79mm x 1.28mm
Pin 1
Remark: The connector is bottom conduct with golden plating of FPC cable
Pin
Symbol
Pin Type
Refer
Description
VBAT
PVDD
I2C_SDA
I2C _SCL
GND
IRQ
Input Power
Input Power
I/O
N/A
N/A
PVDD
PVDD
N/A
PVDD
NFC_Presence
N/A
VEN
VBAT
TX_PWR_REQ
VDD
10
11
12
S1
S2
PMUVCC
SWIO_UICC
DWL_REQ
GND
GND
Input Power
I/O
N/A
VDD(SIM)
PVDD
N/A
N/A
Power supply from system (4.5V - 5.5V)
Power supply to I/O (3.0V – 3.6V)
I2C data
I2C clock
Ground
Interrupt from NFC module to the host (Host_Wake)
Connect to ground for NFC module presence bit (Low
active)
Reset pin. Set the device in Hard Power Down
(External TX power supply request)
(Active high 1.8V level output)
Indicates NFC busy state during NFC communication
to touchpad.
Power supply to UICC(1.78V~3.3V)
SWP data connection to SIM
Firmware download control pin
Ground
Ground
Remark: P = power supply, G = ground, I = input, O = output, I/O = input/output
15
COMPANY CONFIDENTIAL
2> Pin characteristics
VEN input pin characteristics
Symbol
Parameter
VIH
VIL
IIH
IIL
Ci
HIGH-level input voltage
LOW-level input voltage
HIGH-level input current
LOW-level input current
Input capacitance
Conditions
VEN voltage=VBAT
VEN voltage=0V
Min
Typ
Max
Unit
1.1
VBAT
0.4
µA
µA
pF
Pin characteristics for IRQ, and TX_PWR_REQ
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
VOH
HIGH-level output voltage
VOL
CL
tf
LOW-level output voltage
Load capacitance
Fall time
IOH<3mA
IRQ and CLK_REQ pin
TX_PWR_REQ pin
IOL<3mA
VPVDD -0.4
VDD-0.4
VPVDD
VDD
0.4
20
pF
3.5
10
ns
ns
0.35
55
3.5
10
0.85
120
ns
ns
MΩ
kΩ
tr
Rise time
Rpd
[1]
Pull-down resistance
CL=12pF max
High speed
Low speed
CL=12pF max
High speed
Low speed
IRQ and CLK_REQ pins
TX_PWR_REQ pin [1]
[1]
Activated in HPO and Monitor states.
Input pin characteristics for DWL_REQ
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
VIH
VIL
VIH
VIL
IIH
IIL
HIGH-level input voltage
LOW-level input voltage
HIGH-level input voltage
LOW-level input voltage
HIGH-level input current
LOW-level input curent
VPVDD=1.8V
V PVDD=1.8V
VPVDD=3V
VPVDD=3V
0.65*VPVDD
0.35*VPVDD
0.8
µA
µA
Ci
Rpd
Input capacitance
Pull down resistance
0.35
0.85
pF
MΩ
Extra pull-down
Pin characteristics for HIF3(used as I2C-bus SDA) and HIF4(used as I2C-bus SCL)
Symbol
Parameter
VOL
CL
tf
LOW-level output voltage
Load capacitance
Fall time
tr
Rise time
VIH
VIL
IIH
IIL
Ci
HIGH-level input voltage
LOW-level input voltage
HIGH-level input current
LOW-level input current
Input capacitance
[1]
Conditions[1]
IOL<3mA
[1]
CL=100 pF;
Rpull-up=2kΩ; Standard and Fast mode
[1]
CL=100 pF;
Rpull-up=1kΩ; High-speed mode
[1]
CL=100 pF;
Rpull-up=2kΩ; Standard and Fast mode
[1]
CL=100 pF;
Rpull-up=1kΩ; High-speed mode
VI= VPVDD; high impedance
VI=0V; high impedance
Min
Typ
Max
Unit
30
0.4
10
250
pF
ns
80
110
ns
30
250
ns
10
100
ns
0.7 *VPVDD
-1
VPVDD
0.3*VPVDD
µA
µA
pF
Only for pin HIF3(I C-bus SDA), HIF4(I C-bus SCL) is only used as input.
16
COMPANY CONFIDENTIAL
SWIO_UICC pin characteristics
Symbol
Parameter
VOH
HIGH-level output voltage
VOH
HIGH-level output voltage
VOH
HIGH-level output voltage
VOL
I[1]
IH
LOW-level output voltage
HIGH-level input current
Conditions
Min
Typ
Max
Unit
IIH=1mA;
IDD(SIM)=50mA;
VDD(SIM_PMU)=2.75V;
VDD(SIM_PMU) in class B
[1]
ISIM_SWIO=1mA;
IDD(SIM)=30mA;
VDD(SIM_PMU)=1.67V;
VDD(SIM_PMU) in class C
[1]
IIH =1mA;
IDD(SIM)=5mA;
VDD(SIM_PMU)=0V;
VDD(SIM)-VDDD
[1]
0µA Recommend FPC cable
17
COMPANY CONFIDENTIAL
4.4. Shielding Cover of NFC module
Dimension (L x W x H): 11.69mm x 7.88mm x 1.35mm, Thickness: 0.15mm
Materials: KU360S
4.5. Picture of NFC module
Pin 1
(Top view)
(Bottom view)
18
COMPANY CONFIDENTIAL
7. Marking Information
Label information
21
COMPANY CONFIDENTIAL
22
COMPANY CONFIDENTIAL
8. Packing information
23
COMPANY CONFIDENTIAL
24
9. Reliability Test plan
No
Item
COMPANY CONFIDENTIAL
℃ ℃
℃
℃℃
℃
Test Condition
Pull test & Cross
Section (2pcs)
Cross Section: 1pcs
Pull Test: 1pcs
1.
2.
3.
Qty
Visual inspection: All locations
Cross
section:
BGA/Connector/PTH
Hole/Via
Hole (SMT/PIH)
Pull strength: 0.4mm/0.5mm pitch
QFP
4. Power on;
5. Temp.= -40 ;
6. Test Period = 240hrs.
1.Power Off ,
2.Temperature=100
3.Test period=96 Hours
4.Power on 3times
1.Power Off
2.Temperature=0
3.Test period=96 Hours
4.Power on 3times
Temperature-Humidity
Bias (THB)
1. Power On( apply core voltage to
PCBA )
2. Temp.= 85 & Humi.= 85%R.H
3. Test period= 400 Hours
Accelerated Thermal
Cycles (ATC)
ATC:
1.Power off
2.Ta=85 for 7.5mins
3.Ta=85 to -40 for 7.5mins
4.Ta=-40 for 7.5mins
5.Ta=-40 to 85 for 7.5mins
6.Repeat 630cycles
Cross Section(both Bright & Dark):
BGA/CONNECTOR/PTH Hole/ Via
Hole (SMT/PIH)
Sine
Vibration(Unpackaged
1. Frequency = 5 ~ 500 ~ 5 HZ;
2. Acceleration = 2 G;
3. Sweep time: 3mins/cycle;
4. Each of x, y, z axis/ 30 min;
5. Power on and continuously ping
AP/SG./Golden(AP for WLAN, SG for
WWAN, Golden for BT)
6. Product need to be connected with
the mating connector which used in
laptop.
Shock
Test(Unpackaged)
1. Half-Sine wave ,50G , 11msec
2. Test +/- x, y, z axes
3. Three shock per axes, total 18
shocks.
4. Product need to be connected with
the mating connector which used in
laptop.
5. Detect by an electrical discontinuity
monitor.
Sine
Vibration(Packaged)
1. Frequency = 5 ~ 500 ~ 5 HZ;
2. Acceleration = 2 Grms;
3. Each of x, y, z axis/ 30 mins.
Carton
Shock
Test(Packaged)
1. Sine wave ,230G , 3msec ;
2. Test +/- x, y, z axes
Carton
Tin Wisker
1. Power off 60/95%RH for 2000hrs;
2. Room Temperature 2000hrs.
10
Low
Test
Hot Start Test
10
11
Temperature
Cold Start Test
：
：
Criteria
Result
1. Visual Inspection – Compliance with IPC-A-610D
Class 3 & 39T0261;
2. Function test Pass;
3. Cross section
- No separation
- Allowable Crack Length: Max. 25% of pad diameter
4. Pull test
- 800g for 0.4mm pitch QFP, 1kg for 0.5mm
pitch QFP
TBD
Pls refer to ATC
TBD
1.
2.
1.
2.
Visual Inspection – Compliance with IPC-A610D Class 3 & 39T0261;
Function test Pass.
TBD
Visual Inspection – Compliance with IPC-A-610D
Class 3 & 39T0261;
Function test Pass.
TBD
Pls refer to ATC
TBD
Visual Inspection – Compliance with IPC-A-610D
Class 3 & 39T0261;
2. Function test Pass;
3. Cross section ( AFTER 630 cycles )
- No separation
- Allowable Crack Length: Max. 25% of pad diameter
TBD
Visual Inspection – Compliance with IPC-A-610D
Class 3 & 39T0261;
Function test Pass;
No disconnect between device & AP/SG /Golden
during the test .
TBD
Visual Inspection – Compliance with IPC-A-610D
Class 3 & 39T0261;
No electrical discontinuity is greater than 1
microsecond.
TBD
Visual Inspection – Compliance with IPC-A-610D
Class 3 & 39T0261;
Function test Pass.
TBD
Visual Inspection – Compliance with IPC-A-610D
Class 3 & 39T0261;
Function test Pass.
TBD
1.
1.
2.
3.
1.
2.
1.
2.
1.
2.
Whisker Length <50um
TBD
25
COMPANY CONFIDENTIAL
10. Notice
Operating Temperature Conditions
The product shall be capable of continuous reliable operation when operating in ambient
temperature of 0°C to 70°C.
Non-Operating Temperature Conditions
Neither subassembly shall be damaged nor shall the operational performance be degraded
when restored to the operating temperature when exposed to storage temperature in the
range of -20°C to +85°C.
Operating Humidity Conditions
The product shall be capable of continuous reliable operation when subjected to relative
humidity in the range of 0% and 85% non-condensing.
Handling Environment
Please make sure to avoid mechanical shock and vibration for this module.
Please do not drop the module.
Please do not clean the module.
26
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
−
Reorient or relocate the receiving antenna.
−
Increase the separation between the equipment and receiver.
−
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
−
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This transmitter must not be co‐located or operating in conjunction with any other antenna or
transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator
& your body.
This device is intended only for OEM integrators under the following conditions:
The antenna must be installed such that 20 cm is maintained between the antenna and users, and
The transmitter module may not be co‐located with any other transmitter or antenna.
As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM
integrator is still responsible for testing their end‐product for any additional compliance requirements
required with this module installed
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop
configurations or co‐location with another transmitter), then the FCC authorization is no longer
considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM
integrator will be responsible for re‐evaluating the end product (including the transmitter) and
obtaining a separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed such
that 20 cm may be maintained between the antenna and users. The final end product must be labeled
in a visible area with the following: “Contains FCC ID:MCLT77H747”. The grantee's FCC ID can be used
only when all FCC compliance requirements are met.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to
install or remove this RF module in the user’s manual of the end product which integrates this
module.
The end user manual shall include all required regulatory information/warning as show in this manual.
Industry Canada statement:
This device complies with ISED’s licence‐exempt RSSs. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes : (1) le dispositif ne doit pas produire de
brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage
susceptible de provoquer un fonctionnement indésirable.
Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm
de distance entre la source de rayonnement et votre corps.
This device is intended only for OEM integrators under the following conditions: (For module device
use)
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and
2) The transmitter module may not be co‐located with any other transmitter or antenna.
As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM
integrator is still responsible for testing their end‐product for any additional compliance requirements
required with this module installed.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes: (Pour
utilisation de dispositif module)
1) L'antenne doit être installée de telle sorte qu'une distance de 20 cm est respectée entre l'antenne
et les utilisateurs, et 2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou
antenne.
Tant que les 2 conditions ci‐dessus sont remplies, des essais supplémentaires sur l'émetteur ne seront
pas nécessaires. Toutefois, l'intégrateur OEM est toujours responsable des essais sur son produit final
pour toutes exigences de conformité supplémentaires requis pour ce module installé.
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or
co‐location with another transmitter), then the Canada authorization is no longer considered valid and
the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be
responsible for re‐evaluating the end product (including the transmitter) and obtaining a separate
Canada authorization.
NOTE IMPORTANTE:
Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines configurations
d'ordinateur portable ou de certaines co‐localisation avec un autre émetteur), l'autorisation du
Canada n'est plus considéré comme valide et l'ID IC ne peut pas être utilisé sur le produit final. Dans
ces circonstances, l'intégrateur OEM sera chargé de réévaluer le produit final (y compris l'émetteur) et
l'obtention d'une autorisation distincte au Canada.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may
be maintained between the antenna and users. The final end product must be labeled in a visible area with the
following: “Contains IC: 2878D-T77H747”.
Plaque signalétique du produit final
Ce module émetteur est autorisé uniquement pour une utilisation dans un dispositif où l'antenne peut être installée
de telle sorte qu'une distance de 20cm peut être maintenue entre l'antenne et les utilisateurs. Le produit final doit
être étiqueté dans un endroit visible avec l'inscription suivante: "Contient des IC: 2878D-T77H747".
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove
this RF module in the user’s manual of the end product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in this manual.
Manuel d'information à l'utilisateur final
L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant à la façon d'installer
ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intègre ce module.
Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et avertissements comme
indiqué dans ce manuel.
This radio transmitter (IC: 2878D-T77H747, Model: T77H747) has been approved by Industry Canada to operate with
the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list,
having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Cet émetteur radio (IC: 2878D-T77H747, Modèle: T77H747) a été approuvé par Industrie Canada pour fonctionner
avec les types d'antenne énumérés ci-dessous avec le gain maximal admissible indiqué. types d'antennes non inclus
dans cette liste, ayant un gain supérieur au gain maximum indiqué pour ce type, sont strictement interdits pour une
utilisation avec cet appareil.
DETACHABLE ANTENNA USAGE
This radio transmitter (IC: 2878DT-77H747 / Model: T77H747) has been approved by ISED to operate with
This
radio transmitter
2878DT77H747
/ Model:
T77H747)
been approved
ISEDnot
to operate
the
the antenna
type listed(IC:
below
with maximum
permissible
gainhas
indicated.
Antennaby
types
includedwith
in this
antenna
type
listed
below
with
maximum
permissible
gain
indicated.
Antenna
types
not
included
in
this
list,
list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with
having
a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this
this device.
device.
Le présent émetteur radio (IC: 2878D-T77H747 / Model: T77H747) a été approuvé par ISED pour fonctionner
Le
présent
émetteur
radioénumérés
(IC: 2878DT77H747
/ Model:
T77H747)
a été approuvé
pour
fonctionner
avec
les types
d'antenne
ci-dessous et
ayant un
gain admissible
maximal.par
LesISED
types
d'antenne
non
avec
types
d'antenne
ci-dessous
et ayant
un gain
admissible
maximal.
Les types d'antenne
non
inclusles
dans
cette
liste, et énumérés
dont le gain
est supérieur
au gain
maximal
indiqué,
sont strictement
interdits pour
l'exploitation
de l'émetteur.
inclus
dans cette
liste, et dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour
l'exploitation de l'émetteur.
ġ
低功率電波輻射性電機管理辦法
第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更 頻率、加大
功率或變更原設計之特性及功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應 立
即停用，並改善至無干擾時方得繼續使用。 前項合法通信，指依電信法規定作業之無線電通信。
低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
模組認證：
1. 本模組於取得認證後將依規定於模組本體標示審驗合格標籤。
2. 系統廠商應於平台上標示「本產品內含射頻模組： XXXyyyLPDzzzz‐x」字樣。
「電磁波曝露量 MPE 標準值 1mW/cm ，送測產品實測值為 0.97 mW/cm 」

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Create Date                     : 2017:10:26 12:01:59+08:00
Creator Tool                    : Microsoft® Office Word 2007
Modify Date                     : 2017:10:26 16:02:42+08:00
Metadata Date                   : 2017:10:26 16:02:42+08:00
Format                          : application/pdf
Creator                         : SherryHsu
Producer                        : Microsoft® Office Word 2007
Document ID                     : uuid:45c2ebc4-05c7-4f64-8f71-8aac5109f5fb
Instance ID                     : uuid:e7f63f33-4610-441a-9ab9-5238e089b6e2
Has XFA                         : No
Page Count                      : 30
Language                        : zh-TW
Author                          : SherryHsu

EXIF Metadata provided by EXIF.tools