HON HAI PRECISION IND U58H004 Wireless LAN 802.11b MiniPCI Card User Manual

HON HAI Precision Ind. Co., Ltd. Wireless LAN 802.11b MiniPCI Card Users Manual

Users Manual

Download: HON HAI PRECISION IND U58H004 Wireless LAN 802.11b MiniPCI Card User Manual
Mirror Download [FCC.gov]HON HAI PRECISION IND U58H004 Wireless LAN 802.11b MiniPCI Card User Manual
Document ID238856
Application IDJuVtkXDlr16BnCSR4DGg2g==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize176.77kB (2209592 bits)
Date Submitted2002-04-24 00:00:00
Date Available2002-04-18 00:00:00
Creation Date2002-04-01 16:11:45
Producing SoftwareIBM (ID Workbench)
Document Lastmod2002-04-01 18:02:43
Document TitleThinkPad® T30 Series Service and Troubleshooting Guide
Document CreatorXPP
Document Author: IBM

򔻐򗗠򙳰
ThinkPad® T30 Series
Service and Troubleshooting Guide
򔻐򗗠򙳰
ThinkPad® T30 Series
Service and Troubleshooting Guide
Note
Before using this information and the product it supports, be sure to read the general information under
Appendix A, “Important safety instructions” on page 39, Appendix B, “Wireless related information” on
page 45, Appendix C, “Wireless regulatory notice” on page 47, Appendix D, “Warranty information” on page 53,
and Appendix E, “Notices” on page 67.
DANGER
v To avoid electric shock hazard, connect and disconnect cables appropriately when installing, moving or opening
the covers of this product or attached devices. Use the power cord with a properly grounded outlet.
v Do not leave the base of your computer in contact with your lap or any part of your body for an extended
period when the computer is functioning or when the battery is charging. Your computer dissipates some heat
during normal operation. This heat is a function of the level of system activity and battery charge level.
Extended contact with your body, even through clothing, could cause discomfort or, eventually, a skin burn.
v To reduce the risk of electric shock, do not use your computer in or near water.
v To avoid electric shock, do not use your computer with the telephone cable connection during an electrical
storm. Do not connect the cable to or disconnect it from the telephone outlet on the wall during an electrical
storm.
v Store packing materials safely out of the reach of children to prevent the risk of suffocation from plastic bags.
v The battery pack contains a small amount of harmful substances. There is danger of an explosion if the battery
pack is incorrectly replaced, exposed to fire or water, short-circuited or disassembled. Keep the battery pack
away from children and do not put it in trash that is disposed of in landfills.
v To reduce the risk of fire, use only No. 26 AWG or thicker telephone cable.
v The fluorescent lamp in the LCD contains mercury. Do not put it in trash that is disposed of in landfills. Rough
handling or dropping the computer can cause the LCD to break and the internal fluid to get into your eyes or
on your hands. Immediately wash the affected areas with water. If symptoms persist, seek medical care.
v Do not disassemble the optical storage drive unit, as this might result in hazardous radiation exposure.
v Avoid direct eye exposure with the laser beam contained in some drives.
First Edition (March 2002)
The following paragraph does not apply to the United Kingdom or any country where such provisions are
inconsistent with local law:
INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS PUBLICATION ″AS IS″ WITHOUT
WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Some states do not allow disclaimer of express or implied warranties in certain transactions, therefore, this statement
may not apply to you.
This information could include technical inaccuracies or typographical errors. Changes are periodically made to the
information herein; these changes will be incorporated in new editions of the publication. IBM may make
improvements and/or changes in the product(s) and/or the program(s) described in this publication at any time
without notice.
IBM may use or distribute any of the information you supply in any way it believes appropriate without incurring
any obligation to you.
© Copyright International Business Machines Corporation 2002. All rights reserved.
US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract
with IBM Corp.
Important Notice for Users
The FCC RF Safety Requirement
Users are requested to use IBM® ThinkPad T30 Series computer with the
proper operation for each model shown below.
Multiple Transmitters model
If you find the FCC ID “ANOCORN1TASUHOP” on the label on the bottom
of your ThinkPad computer, your computer is approved as a Multiple
Transmitters device that is permitted to use two or more wireless option PC
Cards simultaneously in the computer. Please make sure of the following
grant conditions.
1. Before you use a Bluetooth option or wireless option PC Card in your
ThinkPad T30 computer, visit the IBM site at
www.ibm.com/pc/qtechinfo/MIGR-39377.html and confirm the updated
list of RF option devices that have been approved to cooperate with the
integrated wireless feature.
2. When you use any other RF option device that is not listed on the IBM
site, all other wireless features including the integrated transmitter in your
ThinkPad computer are required to be turned off.
3. Users are requested to follow the RF Safety instructions on wireless option
devices that are included in the RF option device’s user’s manual.
Single Transmitter model
There is no FCC ID shown on the enclosure of this model. Instead you will
find an indicator pointing the location of the FCC ID at the bottom side of
your ThinkPad computer. You are prohibited to use the integrated wireless
LAN Mini-PCI Card and a wireless option PC Card at once on this model.
See Appendix C, “Wireless regulatory notice” on page 47 for more details.
© Copyright IBM Corp. 2002
iii
iv
ThinkPad® T30 Series Service and Troubleshooting Guide
Finding information with Access ThinkPad
Find answers to questions about your computer and view IBM Web sites by
pressing the ThinkPad button to open Access ThinkPad, your on-board
computer help center.
© Copyright IBM Corp. 2002
Take a tour of your ThinkPad computer and learn how to get
started, customize your computer, add memory, protect data,
recover applications and data files, upgrade, and solve
problems.
Once you are familiar with the hardware features of your
computer, click the Tools and Tips tab to get the most out of
those features, like Wireless Networking, Maximizing your
battery life, and even personalizing Access ThinkPad. Click
Access Help to open a comprehensive help system that offers
information such as how to change or upgrade the memory in
your computer.
Visit these IBM Web sites to join an interactive community of
ThinkPad users, download new backgrounds, purchase
accessories, or get online support.
Keyword Search provides a quick way to search information in
Access Help.
Click System Information to view information about your
system, such as model number, serial number, and hard disk
capacity.
vi
ThinkPad® T30 Series Service and Troubleshooting Guide
Some of the topics in your help system contain brief video clips that show
you how to perform certain tasks, such as replacing your battery, inserting a
PC Card, or upgrading your memory. Use the controls shown to play, pause,
and rewind the video clip.
Finding information with Access ThinkPad
vii
viii
ThinkPad® T30 Series Service and Troubleshooting Guide
Contents
Important Notice for Users. . .
The FCC RF Safety Requirement .
. iii
. iii
Finding information with Access ThinkPad
vi
Chapter 1. Overview of your new ThinkPad
computer . . . . . . . . . . . .
Your ThinkPad at a glance . . . . . .
Features . . . . . . . . . . . . .
Specifications . . . . . . . . . . .
Caring for your ThinkPad computer . . .
Chapter 2. Solving computer problems
Diagnosing problems . . . . . . .
Troubleshooting . . . . . . . . .
Error messages . . . . . . . .
Errors without messages . . . . .
A password problem . . . . . .
A power switch problem . . . . .
Keyboard problems . . . . . .
UltraNav™ problems . . . . . .
Standby or hibernation problems . .
Computer screen problems . . . .
Battery problems . . . . . . .
Hard disk drive problems . . . .
Other problems . . . . . . . .
Starting BIOS Setup Utility . . . . .
Recovering pre-installed software . . .
Upgrading the hard disk drive . . . .
Replacing the battery . . . . . . .
. 9
10
11
11
14
15
16
16
17
18
21
23
24
24
27
28
30
32
Chapter 3. Getting help and service from
IBM. . . . . . . . . . . . . . . 33
Getting help and service . . . . . . . . 34
Getting help on the Web . . . . . . . . 34
Getting help by fax . . . . . . . . . 35
Calling IBM . . . . . . . . . . . . 36
Getting help around the world . . . . . . 37
Appendix A. Important safety instructions
© Copyright IBM Corp. 2002
Modem safety information .
Laser compliance statement .
. 42
. 44
Appendix B. Wireless related information
45
Wireless Interoperability . . . . . . . . 45
Usage environment and your Health . . . . 45
Appendix C. Wireless regulatory notice . .
USA - Federal Communications Commissions
(FCC) . . . . . . . . . . . . . .
Canada - Industry Canada (IC). . . . . .
Notice for Users in Singapore . . . . . .
47
47
50
51
Appendix D. Warranty information . . . . 53
Warranty Period . . . . . . . . . . 53
Warranty service and support . . . . . . 53
Before you call for service . . . . . . 54
Calling for service . . . . . . . . . 54
IBM Statement of Limited Warranty
Z125-4753-06 8/2000 . . . . . . . . . 55
Part 1 - General Terms . . . . . . . 55
Part 2 - Country-unique Terms . . . . . 58
Appendix E. Notices . . . . . . . . . 67
Processing date data . . . . . . . . . 67
References to the Web site addresses . . . . 68
Electronic emission notices . . . . . . . 68
Telecommunication notices . . . . . . . 69
Fax Branding . . . . . . . . . . 70
Industry Canada requirements . . . . . . 71
Notice for Australia . . . . . . . . . 72
Notice for New Zealand . . . . . . . . 73
Notice for European Union countries. . . . 78
Product notice requirements . . . . . . 79
Trademarks . . . . . . . . . . . . 79
Index .
. 81
42
ix
x
ThinkPad® T30 Series Service and Troubleshooting Guide
Chapter 1. Overview of your new ThinkPad computer
Your ThinkPad at a glance
Features . . . . . . .
© Copyright IBM Corp. 2002
. 2
. 3
Specifications . . . . . . . . .
Caring for your ThinkPad computer .
. 5
. 6
Your ThinkPad at a glance
Your ThinkPad at a glance
Front view
Rear view
ThinkPad® T30 Series Service and Troubleshooting Guide
Features
Features
Processor
v Intel® Pentium® 4 processor-M
Memory
v Built-in: 128 MB or 256 MB, depending on the model
v Maximum: 1024 MB
Storage device
v 2.5-inch hard disk drive: 20 GB or 40 GB, depending on the model
Display
The color display uses TFT technology:
v Size: 14.1 inch
v Resolution:
– LCD: Up to 1400-by-1050, depending on the model
– External monitor: Up to 2048-by-1536
v Brightness control
Keyboard
v 84-key, 85-key, or 89-key
v UltraNav™ (TrackPoint® and touch pad)
Note: Some models have the TrackPoint only, without a touch pad and its
buttons.
Fn key function
ThinkPad button
Volume control buttons
ThinkLight™
Chapter 1. Overview of your new ThinkPad computer
Features
Diskette drive - available on selected models
To get the best performance from your diskette drives, use high-quality
diskettes (such as IBM diskettes) that meet or exceed the following standards:
v 1-MB, 3.5-inch, unformatted diskette:
– ANSI (American National Standards Institute) X3.137
– ISO (International Standards Organization) 8860
– ECMA (European Computer Manufacturers Association) 100
v 2-MB, 3.5-inch, unformatted diskette:
– ANSI X3.171
– ISO 9529
– ECMA 125
External interface
Serial connector (EIA-RS232D)
Parallel connector (IEEE 1284A)
External-monitor connector
PC Card slots (Type I, Type II, or Type III PC Card)
Headphone jack
Line-in jack
Microphone jack
Video-out connector
2 Universal Serial Bus (USB) connectors
Infrared port
RJ11 telephone connector (available if the modem feature is installed)
RJ45 Ethernet connector
v Ultrabay™ Plus
v Docking connector
v Integrated wireless LAN (IEEE 802.11b) feature (on some models)
v Integrated Bluetooth feature (on some models)
ThinkPad® T30 Series Service and Troubleshooting Guide
Specifications
Specifications
Size
v Width: 304 mm (12.0 in.)
v Depth: 250 mm (9.8 in.)
v Height: 36.6 mm (1.4 in.)
Environment
v Maximum altitude without pressurization: 3048 m (10,000 ft)
v Temperature
– At altitudes up to 2438 m (8000 ft)
- Operating with no diskette: 5° to 35°C (41° to 95°F)
- Operating with a diskette: 10° to 35°C (50° to 95°F)
- Not operating: 5° to 43°C (41° to 110°F)
– At altitudes above 2438 m (8000 ft)
- Maximum operating temperature, 31.3°C (88° F)
Note: When you charge the battery pack, its temperature must be at least
10°C (50°F).
v Relative humidity:
– Operating with no diskette in the drive: 8% to 95%
– Operating with a diskette in the drive: 8% to 80%
Heat output
v 72 W (246 Btu/hr) maximum
Power source (ac adapter)
v Sine-wave input at 50 to 60 Hz
v Input rating of the ac adapter: 100-240 V ac, 50 to 60 Hz
Battery pack
v Lithium-ion (Li-Ion) battery pack
– Nominal voltage: 10.8 V dc
– Capacity: 4.4 AH
Chapter 1. Overview of your new ThinkPad computer
Caring for your ThinkPad computer
Caring for your ThinkPad computer
Though your computer is designed to function reliably in normal work
environments, you need to use common sense in handling it. By following
these important tips, you will get the most use and enjoyment out of your
computer.
Important tips:
Be careful about where and how you work
v Do not leave the base of your computer in contact with your lap or any
part of your body for an extended period when the computer is functioning
or when the battery is charging. Your computer dissipates some heat during
normal operation. This heat is a function of the level of system activity and
battery charge level. Extended contact with your body, even through
clothing, could cause discomfort or, eventually, a skin burn.
v Place liquids away from your computer to avoid spills, and keep your
computer away from water (to avoid the danger of electrical shock).
v Store packing materials safely out of the reach of children to prevent the
risk of suffocation from plastic bags.
v Keep your computer away from magnets, activated cellular phones,
electrical appliances, or speakers (within 13cm/5 in).
v Avoid subjecting your computer to extreme temperatures (below 5°C/41°F
or above 35°C/95°F).
Be gentle with your computer
v Avoid placing any objects (including paper) between the display and the
keyboard or under the keyboard.
v Do not drop, bump, scratch, twist, hit, vibrate, push or place heavy objects
on your computer, display, or external devices.
v Your computer display is designed to be opened and used at an angle
slightly greater than 90 degrees. Do not open the display beyond 180
degrees, as this might damage the computer hinge.
Carry your computer properly
v Before moving your computer, be sure to remove any media, turn off
attached devices, and disconnect cords and cables.
v Be sure your computer is in standby or hibernation mode, or turned off,
before moving it. This will prevent damage to the hard disk drive and data
loss.
v When picking up your open computer, hold it by the bottom. Do not pick
up or hold your computer by the display.
ThinkPad® T30 Series Service and Troubleshooting Guide
Caring for your ThinkPad computer
v Use a quality carrying case that provides adequate cushion and protection.
Do not pack your computer in a tightly packed suitcase or bag.
Handle storage media and drives properly
v Avoid inserting diskettes at an angle and attaching multiple or loose
diskette labels, as these can lodge in the drive.
v If your computer comes with a CD, DVD, or CD-RW/DVD drive, do not
touch the surface of a disc or the lens on the tray.
v Wait until you hear the CD or DVD click into the center pivot of the CD,
DVD, or CD-RW/DVD drive before closing the tray.
v When installing your hard disk, diskette, CD, DVD, or CD-RW/DVD drive,
follow the instructions shipped with your hardware, and apply pressure
only where needed on the device. See Access ThinkPad, your on-board help
system, for information on replacing your hard disk drive (open Access
ThinkPad by pressing the ThinkPad button.).
Take care in setting passwords
v Remember your passwords. If you forget a supervisor or hard disk
password, IBM will not reset it, and you might have to replace your system
board or hard disk drive.
Other important tips
v Your computer modem might use only an analog telephone network, or
public-switched telephone network (PSTN). Do not connect the modem to a
PBX (private branch exchange) or any other digital telephone extension line
because this could damage your modem. Analog phone lines are often used
in homes, while digital phone lines are often used in hotels or office
buildings. If you are not sure which kind of phone line you are using,
contact your telephone company.
v Your computer might have both an Ethernet connector and a modem
connector. If so, be sure to connect your communication cable to the correct
one, so your connector is not damaged. See Access ThinkPad, your
on-board help system, for information on the location of these connectors
(press the ThinkPad button to open Access ThinkPad).
v Register your ThinkPad products with IBM (refer to the Web page:
www.ibm.com/pc/register). This can help authorities return your computer
to you if it is lost or stolen. Registering your computer also enables IBM to
notify you about possible technical information and upgrades.
v Only an authorized IBM ThinkPad repair technician should disassemble
and repair your computer.
v Do not modify or tape the latches to keep the display open or closed.
v Take care not to turn your computer over while the ac adapter is plugged
in. This could break the adapter plug.
Chapter 1. Overview of your new ThinkPad computer
Caring for your ThinkPad computer
v Turn off your computer if you are replacing a device in a device bay, or else
verify that the device is warm-or hot-swappable.
v If you exchange drives in your computer, reinstall the plastic bezel faces (if
supplied).
v Store your external and removable hard disk, diskette, CD, DVD, and
CD-RW/DVD drives in the appropriate containers or packaging when they
are not being used.
Cleaning your computer
Occasionally clean your computer as follows:
v Use a soft cloth moistened with nonalkaline detergent to wipe the exterior
of the computer.
v Avoid spraying cleaner directly on the display or the keyboard.
v Gently wipe the display with a soft, dry cloth. If you see a scratchlike mark
on your display, it might be a stain transferred from the keyboard or the
TrackPoint pointer when the cover was pressed from the outside. Wipe or
dust the stain gently with a soft, dry cloth. If the stain remains, moisten a
soft, lint-free cloth with water that does not contain impurities, wring out
as much of the water as you can, and then wipe the display again. Be sure
to dry the display before closing it.
ThinkPad® T30 Series Service and Troubleshooting Guide
Chapter 2. Solving computer problems
Diagnosing problems . . . . .
Troubleshooting . . . . . . .
Error messages . . . . . .
Errors without messages . . .
A password problem . . . .
A power switch problem . . .
Keyboard problems . . . .
UltraNav™ problems . . . .
Standby or hibernation problems
© Copyright IBM Corp. 2002
10
11
11
14
15
16
16
17
18
Computer screen problems . .
Battery problems . . . . .
Hard disk drive problems . .
Other problems . . . . . .
Starting BIOS Setup Utility . . .
Recovering pre-installed software .
Upgrading the hard disk drive . .
Replacing the battery . . . . .
21
23
24
24
27
28
30
32
Solving computer problems
Diagnosing problems
If you have a problem with your computer, you can test it by using
PC-Doctor® for Windows®. To run PC-Doctor for Windows, do as follows:
1. Click Start.
2. Move the cursor to Programs (in Windows XP, All Programs) and then to
PC-Doctor for Windows.
3. Click PC-Doctor for Windows.
4. Choose either the Run Quick Test Set or the Run Normal Test Set.
Attention
Running the Quick Test Set can take up to 10 minutes or longer. Make
sure you have time to run the entire test; do not interrupt the test while
it is running.
The Quick Test Set runs many tests of critical hardware components, but it
does not run all of the diagnostic tests in PC-Doctor for Windows. If
PC-Doctor for Windows reports that all of the tests in the Quick Test Set have
been run and that it has found no problems, consider running more of the
tests in PC-Doctor for Windows.
If you are preparing to contact IBM for support, be sure to print the test log
so that you can rapidly provide information to the help technician.
10
ThinkPad® T30 Series Service and Troubleshooting Guide
Solving computer problems
Troubleshooting
If you do not find your problem here, refer to Access ThinkPad, your
on-board help system. Open Access ThinkPad by pressing the ThinkPad
button. The following section only describes problems that might prevent you
from accessing this help system.
Error messages
Notes:
1. In the charts, x can be any character.
2. The version of PC-Doctor referred to here is PC-Doctor for Windows.
Message
Solution
0175: Bad CRC1, stop
POST task
The EEPROM checksum is not correct (block #6). Have the computer
serviced.
0187: EAIA data access
error
The access to EEPROM is failed. Have the computer serviced.
0188: Invalid RFID
serialization information
area or bad CRC2.
The EEPROM checksum is not correct (block # 0 and 1, or block # 6). The
system board should be replaced, and the box serial number needs to be
reinstalled. Have the computer serviced.
0189: Invalid RFID
configuration
information area
The EEPROM checksum is not correct (block # 4 and 5). The system board
should be replaced, and the UUID needs to be reinstalled. Have the
computer serviced.
0190: Critical low-battery The computer turned off because the battery is low. Connect the ac adapter
error
to the computer and charge the battery, or replace the battery with a fully
charged one.
0197: Invalid Remote
change requested
The remote configuration for the Security Chip has failed. Confirm the
operation and try again.
01C8: More than one
modem devices are
found. Remove one of
them. Press  to
continue.
Remove either a Modem Mini-PCI Card or a Modem Daughter Card,
otherwise press Esc to ignore the warning message. If it does not solve this
problem, have the computer serviced.
01C9: More than one
Ethernet devices are
found. Remove one of
them. Press  to
continue.
Your ThinkPad computer has a built-in Ethernet feature, and you cannot
add another such feature by installing an Ethernet device such as a
Mini-PCI Ethernet Card or an Ethernet Daughter Card. If this error message
is displayed, remove the Ethernet device that you installed. Otherwise press
Esc to ignore the warning message. If this does not solve the problem, have
the computer serviced.
0200: Hard disk error
The hard disk is not working. Make sure that the hard disk drive is attached
firmly. Run the BIOS Setup Utility; then make sure the hard disk drive is
not disabled in the Startup menu.
Chapter 2. Solving computer problems
11
Solving computer problems
Message
Solution
021x: Keyboard error
Make sure that there are no objects placed on the keyboard, or if you have
one, the external keyboard. Turn off the computer, and turn off all attached
devices. Turn on the computer first; then turn on the attached devices.
If you still see the same error code, do the following:
If an external keyboard is connected, do the following:
v Turn off the computer and disconnect the external keyboard; then turn on
the computer. Make sure that the built-in keyboard operates correctly. If it
does, have the external keyboard serviced.
v Make sure that the external keyboard is connected to the correct
connector.
Test the computer by using PC-Doctor.
v If the computer stops during the test, have the computer serviced.
0230: Shadow RAM error The shadow RAM failed. Test your computer’s memory with PC-Doctor. If
you added a memory module just before turning the computer on, reinstall
it. Then test the memory with PC-Doctor.
0231: System RAM error
The system RAM failed. Test your computer’s memory with PC-Doctor. If
you added a memory module just before turning the computer on, reinstall
it. Then test the memory with PC-Doctor.
0232: Extended RAM
error
The extended RAM failed. Test your computer’s memory with PC-Doctor. If
you have increased memory just before turning the computer on, reinstall it.
Then test the memory with PC-Doctor.
0250: System battery
error
The backup battery, which is used to preserve the configuration information,
such as the date and time, while the computer is turned off, is depleted.
Replace the battery and run IBM BIOS Setup Utility to verify the
configuration. If you still have a problem, have the computer serviced.
0251: System CMOS
checksum bad
The system CMOS might have been corrupted by an application program.
The computer uses the default settings. Run IBM BIOS Setup Utility to
reconfigure the settings. If you still see the same error code, have the
computer serviced.
0260: System timer error
Have the computer serviced.
0270: Real time clock
error
Have the computer serviced.
0271: Date and time error Neither the date nor the time is set in the computer. Set the date and time,
using the IBM BIOS Setup Utility.
0280: Previous boot
incomplete
12
Your computer was previously unable to complete the boot process.
Turn the computer off; then turn it on to start the IBM BIOS Setup Utility.
Verify the configuration and then restart the computer either by choosing
the Exit Saving Changes option under the Restart item or by pressing F10.
If you still see the same error code, have the computer serviced.
ThinkPad® T30 Series Service and Troubleshooting Guide
Solving computer problems
Message
Solution
02D0: System cache error The cache is disabled. Have the computer serviced.
02F4: EISA CMOS not
writable
Have the computer serviced.
02F5: DMA test failed
Have the computer serviced.
02F6: Software NMI
failed
Have the computer serviced.
02F7: Fail-safe timer NMI Have the computer serviced.
failed
1802: Unauthorized
network card is plugged
in - Power off and
remove the miniPCI
network card.
The Mini-PCI network card is not supported on this computer. Remove it.
The power-on password
prompt
A power-on password or a supervisor password is set. Type the password
and press Enter to use the computer. If the power-on password is not
accepted, a supervisor password might have been set. Type the supervisor
password and press Enter. If you still see the same error message, have the
computer serviced.
The hard disk password
prompt
A hard disk password is set. Type the password and press Enter to use the
computer.
If you still see the same error message, have the computer serviced.
Hibernation error
The system configuration changed between the time your computer entered
hibernation mode and the time it left this mode, and your computer cannot
resume normal operation.
v Restore the system configuration to what it was before your computer
entered hibernation mode.
v If the memory size has been changed, re-create the hibernation file.
Operating system not
found.
Verify the following:
v The hard disk drive is correctly installed.
v A startable diskette is in the diskette drive
If you still see the same error message, check the boot sequence, using the
IBM BIOS Setup Utility.
Fan error
The cooling fan has failed. Have the computer serviced.
Chapter 2. Solving computer problems
13
Solving computer problems
Message
Solution
EMM386 Not Installed — Edit C:\CONFIG.SYS and change a line from
Unable to Set Page
device=C:\WINDOWS\EMM386.EXE RAM
Frame Base Address.
to
device=C:\WINDOWS\EMM386.EXE NOEMS
and save this file.
CardBus Configuration
Error —Device Disabled
Press F1 to go to the IBM BIOS Setup Utility. Press F9 and then Enter to
load the default setting.
Press F10 and then Enter to restart the system.
Thermal sensing error
The thermal sensor is not functioning correctly. Have the computer serviced.
Errors without messages
Problem: When I turn on the machine, nothing appears on the screen and the
machine does not beep while starting up.
Note: If you are not sure whether you heard any beeps, turn off the
computer; then turn it on again, and listen again. If you are using an
external monitor, refer to“Computer screen problems” on page 21
Solution: If a power-on password is set, press any key to display the
power-on password prompt, and then type the correct password and press
Enter.
If the power-on password prompt does not appear, the brightness level might
be set to minimum brightness. Adjust the brightness level by pressing the
Fn+Home.
If the screen still remains blank, make sure that:
v The battery is installed correctly.
v The ac adapter is connected to the computer and the power cord is plugged
into a working electrical outlet.
v The computer power is on. (Turn on the power switch again for
confirmation.)
If these items are properly set, and the screen remains blank, have the
computer serviced.
Problem: When I turn on the machine, nothing appears on the screen, but I
hear two or more beeps.
14
ThinkPad® T30 Series Service and Troubleshooting Guide
Solving computer problems
Solution: Make sure that the memory card is installed correctly. If it is, but
the screen is still blank, and you hear five beeps, have the computer serviced.
If you hear 4 cycles of 4 beeps each, the Security Chip has a problem. Have
the computer serviced.
Problem: When I turn on the machine, only a white cursor appears on a
blank screen.
Solution: Reinstall your operating system, and turn on the computer. If you
still see only the cursor on the screen, have the computer serviced.
Problem: My screen goes blank while the computer is on.
Solution: Your screen saver or power management may be enabled. Move the
TrackPoint or press a key to exit the screen saver, or press the power switch to
resume from standby or hibernation.
Problem: The DOS full-screen looks smaller.
Solution: If you use a DOS application that supports only 640x480 resolution
(VGA mode), the screen image might look slightly distorted or appear smaller
than the display size. This is to maintain compatibility with other DOS
applications. To expand the screen image to the same size as the actual screen,
start the ThinkPad Configuration Program and click LCD; then select the
Screen expansion function. (The image might still look slightly distorted.)
Note: If your computer has a screen expansion function, you can use the
Fn+F8 keys to expand the screen image.
A password problem
Problem: I forgot my password.
Solution: If you forgot your power-on password, you must take your
computer to an IBM reseller or marketing representative to have the password
canceled.
If you forgot your hard disk password, IBM will not reset your password or
recover data from the hard disk. You must take your computer to an IBM
reseller or an IBM marketing representative to have the hard disk drive
replaced. Proof of purchase is required, and a fee will be charged for parts
and service.
If you forgot your supervisor password, IBM will not reset your password.
You must take your computer to an IBM reseller or IBM marketing
Chapter 2. Solving computer problems
15
Solving computer problems
representative to have the system board replaced. Proof of purchase is
required, and a fee will be charged for parts and service.
A power switch problem
Problem: The system does not respond, and you cannot turn off the computer.
Solution: Turn off the computer by pressing and holding the power switch for
4 seconds or more. If the computer is still not reset, remove the ac adapter
and the battery.
Keyboard problems
Problem: The cursor does not move after the computer returns from one of
the power management modes.
Solution: Make sure you followed the instructions correctly when you
installed Windows with the Advanced Power Management (APM) option.
Note: The APM option is supported in Windows 98, and Windows NT®.
Problem: Some or all of the keys on the keyboard do not work.
Solution: If the problem occurred immediately after the computer returned
from standby mode, enter the power-on password if any is set.
If an external keyboard is connected, the numeric keypad on your computer
does not work. Use the numeric keypad on the external keyboard.
If an external numeric keypad or a mouse is connected:
1. Turn off the computer.
2. Remove the external numeric keypad or the mouse.
3. Turn on the computer and try using the keyboard again.
If the keyboard problem is resolved, carefully reconnect the external numeric
keypad, external keyboard, or mouse, making sure that you have seated the
connectors properly.
If any keys on the keyboard still do not work, have the computer serviced.
Problem: A number appears when you type a letter.
Solution: The numeric lock function is on. To disable it, press and hold Shift;
then press NumLk.
16
ThinkPad® T30 Series Service and Troubleshooting Guide
Solving computer problems
Problem: Some or all of the keys on the external numeric keypad do not
work.
Solution: Make sure that the external numeric keypad is correctly connected
to the computer.
Problem: Some or all of the keys on the external keyboard do not work.
Solution: If you are using the docking station or the port replicator, make sure
that the keyboard cable is correctly connected to the keyboard connector.
If the connection is correct, disconnect the cable and make sure that the
built-in keyboard operates properly. If the built-in keyboard works, there is a
problem with the external keyboard. Try using a different external keyboard.
UltraNav™ problems
Problem: The cursor drifts when the computer is turned on or after it resumes
normal operation.
Solution: The cursor might drift when you are not using the TrackPoint
during normal operation. This is a normal characteristic of the TrackPoint and
is not a defect. Cursor drifting might occur for several seconds under the
following conditions:
v When the computer is turned on.
v When the computer resumes normal operation.
v When the TrackPoint is pressed for a long time.
v When the temperature changes.
Problem: The mouse or the pointing device does not work.
Solution: Make sure that the TrackPoint and the touch pad are set to
Automatic in the ThinkPad Configuration Program. Then detach the mouse or
the pointing device, and try using the TrackPoint and the touch pad. If the
TrackPoint and the touch pad work, the error might be due to the mouse or
the pointing device.
Make sure that the cable for the mouse or the pointing device is securely
connected to the docking station or the port replicator.
Note: For more information, see the manual supplied with the mouse.
Problem: The mouse buttons do not work.
Chapter 2. Solving computer problems
17
Solving computer problems
Solution: If your ThinkPad computer has the TrackPoint only, this problem
may occur.
Change the mouse driver to Standard PS/2® Port Mouse, and then reinstall
IBM PS/2 TrackPoint. Drivers are provided in the C:\IBMTOOLS\DRIVERS
directory on your hard disk drive. If your hard disk drive does not contain
device drivers, refer to the ThinkPad Web site. For access to this Web site,
open Access ThinkPad by pressing the ThinkPad button.
Standby or hibernation problems
Problem: The computer enters standby mode unexpectedly.
Solution: If the processor reaches a temperature that is too high, the computer
automatically enters standby mode to allow the computer to cool and to
protect the processor and other internal components. Also, check the settings
for standby mode, using Battery MaxiMiser.
Problem: The computer enters standby mode immediately after Power-on
self-test (POST) (the standby indicator light turns on).
Solution: Make sure that:
v The battery is charged.
v The operating temperature is within the acceptable range. Refer to
“Specifications” on page 5.
If these items are correct, have the computer serviced.
Problem: The critical low-battery error message is displayed, and the
computer immediately turns off.
Solution: The battery power is getting low. Connect the ac adapter to the
computer, or replace the battery with a fully charged one.
Problem: When you take action to return from standby mode, the computer
display remains blank.
Solution: Check whether an external monitor was disconnected while the
computer was in standby mode. Do not disconnect the external monitor while
the computer is in standby mode or hibernation mode. If no external monitor
is attached when the computer resumes, the computer display remains blank
and output is not displayed. This restriction does not depend on the
resolution value. Press Fn+F7 to bring up the computer display.
Problem: The computer does not return from standby mode, or the standby
indicator stays on and the computer does not work.
18
ThinkPad® T30 Series Service and Troubleshooting Guide
Solving computer problems
Solution: If the system does not return from standby mode, it may have
entered standby or hibernation mode automatically because the battery is
depleted. Check the standby indicator.
v If the standby indicator is on, your computer is in standby mode. Connect
the ac adapter to the computer; then press Fn.
v If the standby indicator is off, your computer is in hibernation mode or
power-off state. Connect the ac adapter to the computer; then press power
button to resume operation.
If the system still does not return from standby mode, your system may stop
responding and you cannot turn off the computer. In this case, you need to
reset the computer. If you have not saved your data, it may be lost. To reset
the computer, press and hold the power button for 4 seconds or more. If the
system is still not reset, remove the ac adapter and the battery.
Problem: Your computer does not enter standby or hibernation mode.
Solution: Check whether any option has been selected that would disable
your computer from entering standby or hibernation mode.
Problem: The computer does not enter standby mode as set by the timer
under Windows 98 or Windows NT.
Solution:
For Windows 98:
The generic CD-ROM or DVD-ROM driver for Windows 98 accesses the
internal CD-ROM or DVD-ROM drive every 3 seconds to see whether a
CD-ROM is inserted there. This prevents your computer from entering
standby mode even after a timeout. To enable the computer to enter standby
mode, do the following:
1. Click Start.
2. Move the cursor to Settings and Control Panel.
3. Click Control Panel, and then double-click System.
4.
5.
6.
7.
8.
Click the Device Manager tab.
Click the + mark of CD-ROM.
Double-click the name of the CD-ROM or DVD-ROM.
Click the Settings tab.
Clear the Auto insert notification check box.
Windows 98 no longer detects the insertion of a CD-ROM or a DVD-ROM
automatically.
Chapter 2. Solving computer problems
19
Solving computer problems
For Windows NT:
If you enable the CD-ROM AutoRun feature, the timer cannot trigger the
computer to enter standby mode. To enable the timer, disable the AutoRun
feature by editing the configuration information in the registry as follows:
HKEY_LOCAL_MACHINE\SYSTEM\
CurrentControlSet\Services\Cdrom\
Autorun: 0x1 > Autorun: 0
Problem: The Fn+F12 key combination does not cause the computer to enter
hibernation mode.
Solution: The computer cannot enter hibernation mode:
v If you are using one of the IBM communication PC Cards. To enter
hibernation mode, stop the communication program, and then remove the
PC Card or disable the PC Card slot, using the Control Panel.
v If the hibernation utility is not installed in Windows 98 or Windows NT. To
install the hibernation utility, refer to “Installing device drivers” in the
Access ThinkPad, your on-board help system.
v If the hibernation mode is not enabled. To enable it, do as follows:
For Windows 98:
1. Start the ThinkPad Configuration Program.
2. Click Power Management.
3. Click the Hibernation tab.
4. Click the Enable hibernation button.
5. Click the Create Now button.
For Windows NT:
Note: You must format your hard disk with the FAT format system to use
hibernation mode in Windows NT. If you format your hard disk with
NTFS, the default format in Windows NT, you cannot use hibernation
mode.
1. Start the ThinkPad Configuration Program.
2.
3.
4.
5.
Click
Click
Click
Click
Power Management.
Suspend/Resume Options.
Enable Hibernation.
OK.
For Windows 2000 or Windows XP:
1. Start the ThinkPad Configuration Program.
2. Click Power Management.
20
ThinkPad® T30 Series Service and Troubleshooting Guide
Solving computer problems
3. Click the Hibernate tab.
4. Select the hibernate support checkbox.
5. Click OK.
Note: You can enter hibernation mode by pressing Fn+F12 only if the PM
driver for Windows 2000 or Windows XP has been installed.
Problem: Under Windows XP, the Fn+F3 key combination does not make the
computer screen go blank.
Solution: Windows XP enables multiple users to log on to the system at the
same time. If you are the first user to have logged on to your computer, you
can use the Fn+F3 key combination. Otherwise the combination will not work
on your computer.
Computer screen problems
Problem: The screen is blank.
Solution:
v If the standby status indicator is on (in green), press Fn to resume from the
standby mode.
v If you are using the ac adapter, or using the battery, and the battery status
indicator is on (in green), press Fn+Home to make the screen brighter.
v If you attach an external monitor to your computer, press Fn+F7 to switch
the screen output location.
v If the problem persists, do the “Solution” in the problem below.
Problem: The screen is unreadable or distorted.
Solution: Make sure that:
v The display device driver is installed correctly.
v The display resolution and color depth are correctly set.
v The monitor type is correct.
To check these settings, do as follows:
For Windows 98 and Windows 2000:
1. Double-click Display in the Control Panel. The Display Properties window
opens.
2.
3.
4.
5.
Click the Settings tab.
Check if the color depth and resolution are correctly set.
Click Advanced.
Click the Adapter tab.
Chapter 2. Solving computer problems
21
Solving computer problems
6. Make sure “ATI Mobility RADEON 7500” is shown in the adapter
information window.
7. Click the Monitor tab.
8. Make sure the Monitor type is correct.
For Windows XP:
1. Click Start.
2. Click Control Panel.
3.
4.
5.
6.
Click Appearance and Themes in the Pick a category section.
Click Display in the Pick a Control Panel icon section.
Click the Settings tab.
Check whether the color depth and resolution are correctly set.
7. Click Advanced.
8. Click the Adapter tab.
9. Make sure “ATI Mobility RADEON 7500” is shown in the adapter
information window.
10. Click the Monitor tab.
11. Make sure the Monitor type is correct.
For Windows NT:
1. Double-click Display in the Control Panel. The Display Properties window
opens.
2.
3.
4.
5.
Click the Settings tab.
Check if the color depth and resolution are correctly set.
Click Display Type.
Make sure “ATI Mobility RADEON 7500” is shown in the Display Type
window.
Problem: Incorrect characters appear on the screen.
Solution: Did you install the operating system or application program
correctly? If they are installed and configured correctly, have the computer
serviced.
Problem: The screen stays on even after you turn off your computer.
Solution: Press and hold the power switch for 4 seconds or more to turn off
your computer; then turn it on again.
Problem: Missing, discolored, or bright dots appear on the screen every time
you turn on your computer.
22
ThinkPad® T30 Series Service and Troubleshooting Guide
Solving computer problems
Solution: This is an intrinsic characteristic of the TFT technology. Your
computer’s display contains multiple thin-film transistors (TFTs). A small
number of missing, discolored, or bright dots on the screen might exist all the
time.
Problem: A message, “Unable to create overlay window,” appears when you
try to start DVD playback.
or
You get poor or no playback while running video playback, DVD playback, or
game applications.
Solution: Do either of the following:
v If you are using 32-bit color mode, change the color depth to 16-bit mode.
v If you are using a desktop size of 1280×1024 or larger, reduce the desktop
size and the color depth.
Battery problems
Problem: The battery cannot be fully charged by the power-off method in the
standard charge time for your computer.
Solution: The battery might be over-discharged. Do the following:
1. Turn off the computer.
2. Make sure that the over-discharged battery is in the computer.
3. Connect the ac adapter to the computer and let it charge.
If the battery cannot be fully charged in 24 hours, use a new battery.
If the optional Quick Charger is available, use it to charge the over-discharged
battery.
Problem: Your computer shuts down before the battery status indicator shows
empty, -or- Your computer operates after the battery status indicator shows
empty.
Solution: Discharge and recharge the battery.
Problem: The operating time for a fully charged battery is short.
Solution: Discharge and recharge the battery. If your battery’s operating time
is still short, use a new battery.
Problem: The computer does not operate with a fully charged battery.
Chapter 2. Solving computer problems
23
Solving computer problems
Solution: The surge protector in the battery might be active. Turn off the
computer for one minute to reset the protector; then turn on the computer
again.
Problem: The battery does not charge.
Solution: You cannot charge the battery when it is too hot. If the battery feels
hot, remove it from the computer and allow it to cool to room temperature.
After it cools, reinstall it and recharge the battery. If it still cannot be charged,
have it serviced.
Hard disk drive problems
Problem: The hard disk drive makes a rattling noise intermittently.
Solution: The rattling noise might be heard when:
v The hard disk drive starts accessing the data or when it stops.
v You are carrying the hard disk drive.
v You are carrying your computer.
This is a normal characteristic of a hard disk drive and is not a defect.
Problem: The hard disk drive does not work.
Solution: In the startup menu in IBM BIOS Setup Utility, make sure that there
is no exclamation point ! to the left of the hard disk drive. If there is such a
mark, the hard disk drive is disabled. Clear the mark to enable the drive.
Other problems
Problem: The computer locks or does not accept any input.
Solution: Your computer might lock when it enters standby mode during a
communication operation. Disable the standby timer when you are working
on the network.
To turn off the computer, press and hold the power switch for 4 seconds or
more.
Problem: The computer does not turn off with the power switch.
Solution: If the standby indicator is on and you are working under battery
power, replace the battery with a fully charged one or change your power
source to ac power.
If you still have a problem, press and hold the power switch for 4 seconds or
more; this forces the computer to turn off.
24
ThinkPad® T30 Series Service and Troubleshooting Guide
Solving computer problems
Problem: The computer does not start from a device you want, such as a
diskette drive.
Solution: Refer to the Startup menu of the IBM BIOS Setup Utility. Make sure
that the startup sequence in the IBM BIOS Setup Utility is set so that the
computer starts from the device you want.
Also make sure that the device from which the computer starts is enabled by
checking that there is no ! mark preceding the device name.
Problem: The computer does not respond.
Solution: IRQs for the PCI are all set as 11. The computer does not respond
because it cannot share the IRQ with other devices. Refer to the ThinkPad
Configuration Program.
Problem: Windows NT does not start; however, the message saying that
Windows NT is loading remains on the screen.
Solution: The USB setting might have been changed to Enabled. If so, it might
cause a conflict in allocating memory resources during startup. Disable the
setting, using the BIOS Setup Utility as follows:
1. Turn your computer off and then on again; then, while the message,
“Press F1 for IBM BIOS Setup Utility,” is displayed at the lower left of the
screen, press the F1 key to start the BIOS Setup Utility. The BIOS Setup
Utility menu appears.
2. With the cursor key, select Config; then press Enter.
3. Select USB by pressing Enter.
4. With the cursor key, select Disable; then press Enter.
5. Press F10 and Enter to save this setting and exit this utility.
Problem: Playback of DVD is not smooth.
Solution: If you select the Maximum Battery mode for the Intel SpeedStep™
technology, this problem may occur. This mode is designed to achieve
maximum battery life by switching the processor speed between the regular
low speed and half of that speed, depending on how much the processor is
used. If the use increases, Intel SpeedStep switches the processor speed to the
lower speed. Operation in this mode can severely degrade the performance of
the processor, and thus cause the playback of a DVD to be jerky.
To avoid or reduce this problem, you can choose any of three other modes of
operation, as follows:
v Maximum Performance: Keeps the processor speed high at all times.
Chapter 2. Solving computer problems
25
Solving computer problems
v Automatic: Switches the processor speed between high and low, depending
on how much the processor is used. If the use increases, Intel SpeedStep
switches the processor speed to high.
v Battery Optimized Performance: Keeps the processor speed low at all
times.
To
1.
2.
3.
4.
5.
26
choose a mode, do the following:
Start the ThinkPad Configuration Program.
Click Power Management.
Click the Intel SpeedStep technology tab.
From the list, select the mode you want.
Click OK.
ThinkPad® T30 Series Service and Troubleshooting Guide
Solving computer problems
Starting BIOS Setup Utility
Your computer provides a program, called IBM BIOS Setup Utility, that
enables you to select various setup parameters.
v Config: Set the configuration of your computer.
v Date/Time: Set the date and time.
v Password: Set security features.
v Startup: Set the startup device.
v Restart: Restart the system.
Note: You can set many of these parameters more easily by using the
ThinkPad Configuration Program. For more information on this
Program, refer to the on-board help.
To start IBM BIOS Setup Utility, do as follows:
1. To protect yourself against accidental loss of data, refer to “Backing up
your system” in Access ThinkPad. Open Access ThinkPad by pressing the
ThinkPad button. Backing up your registry saves your computer’s current
configuration.
2. Remove any diskette from the diskette drive, and then turn off the
computer.
3. Turn on the computer; then, while the “Press F1 for IBM BIOS Setup
Utility” message is displayed at the lower-left of the screen, press F1.
If you have set a supervisor password, the “IBM BIOS Setup Utility” menu
appears after you enter the password. You can start the utility by pressing
Enter instead of entering the supervisor password; however, you cannot
change the parameters that are protected by the supervisor password. For
more information, refer to the on-board help.
4. Using the cursor keys, move to an item you want to change. When the
item you want is highlighted, press Enter. A submenu is displayed.
5. Change the items you wish to change. To change the value of an item, use
the F5 or F6 key. If the item has a submenu, you can display it by pressing
Enter.
6. Press F3 or Esc to exit from the submenu.
If you are in a nested submenu, press Esc repeatedly until you reach the
IBM BIOS Setup Utility menu.
Note: If you need to restore the settings to their original state as of the
time of purchase, press the F9 key to load the default settings. You
can also select an option in the Restart submenu to load the default
settings or discard the changes.
7. Select Restart; then press Enter. Move the cursor to the option you want
for restarting your computer; then press Enter. Your computer restarts.
Chapter 2. Solving computer problems
27
Solving computer problems
Recovering pre-installed software
If your hard disk drive data is damaged or accidentally erased, you can
restore the software that was shipped with your computer. This software
includes your pre-installed operating system, applications, and device drivers.
You can restore your pre-installed software using the Product Recovery
program.
The Product Recovery program is in a section of your hard disk drive that is
not displayed by Windows Explorer.
Note: The recovery process might take up to 2 hours.
Attention
All of the files on the primary hard disk partition (usually drive
C) will be lost in the recovery process. Be sure to back up copies
of the files you have saved on your drive C before you begin.
Note: You might need to use a diskette drive in the recovery process. Use a
drive that is compatible with your computer.
Note: In the unlikely event that you need to recover the pre-installed software
and you are unable to start the Product Recovery program, you will
need a Recovery Repair diskette. Follow the instructions below, “To
create a Recovery Repair diskette,” soon after you start using your
computer. Save the Recovery Repair diskette in a safe place, in case you
need it later.
To use the Product Recovery program to restore your pre-installed software,
do the following:
1. Create a Recovery Repair diskette, according to the procedure below.
2. If possible, save all your files to media other than your hard disk.
3. Turn off your computer.
4. Turn on your computer. At the prompt, press F11. (The prompt to press
F11 appears for only a few seconds. You must press F11 quickly.) The
Product Recovery program main menu opens.
Note: If pressing F11 does not start the Product Recovery program, use
the Recovery Repair diskette to enable the Product Recovery
program.
5. Select the recovery options you want, and then follow the instructions on
the screen.
28
ThinkPad® T30 Series Service and Troubleshooting Guide
Solving computer problems
6. When the Product Recovery program finishes, your computer will restart
and begin the configuration process.
To create a Recovery Repair diskette
If the F11 recovery option is not present you can use the Recovery Repair
diskette to enable the F11 Product Recovery option.
To make a Recovery Repair diskette, do the following:
1. Shut down and restart your computer.
2. At the prompt, press F11. (The option to press F11 appears for only a few
seconds. You must press F11 quickly.) The Product Recovery program
main menu opens.
3.
4.
5.
6.
Select System Utilities from the main menu. Press Enter.
Select Create a Recovery Repair diskette. Press Enter.
Follow the on-screen instructions.
When the process is completed, label your diskette as the Recovery Repair
diskette and save it for future use.
To use the Recovery Repair diskette:
1. Shut down and turn off your computer.
2. Insert the Recovery Repair diskette into the drive; then turn on the
computer.
3. Follow the on-screen instructions.
Chapter 2. Solving computer problems
29
Upgrading the hard disk drive
Upgrading the hard disk drive
You can increase the storage capacity of your computer by replacing the hard
disk drive with one of greater capacity. You can purchase a new hard disk
drive from your IBM reseller or IBM marketing representative.
Note: Replace the hard disk drive only if you upgrade it or have it repaired.
The connectors and bay of the hard disk drive were not designed for
frequent changes, or drive swapping.
Attention
Handling a hard disk drive
v Do not drop the drive or subject it to physical shocks. Put the drive on
a material, such as soft cloth, that absorbs the physical shock.
v Do not apply pressure to the cover of the drive.
v Do not touch the connector.
The drive is very sensitive. Incorrect handling can cause damage and
permanent loss of data on the hard disk. Before removing the hard disk
drive, make a backup copy of all the information on the hard disk, and
then turn the computer off. Never remove the drive while the system is
operating, in standby mode, or in hibernation mode.
To replace the hard disk drive, do the following:
1. Turn off the computer; then disconnect the ac adapter and all cables
from the computer.
2. Close the computer display, and turn the computer over.
3. Remove the battery.
4. Remove the screw that secures the hard disk drive.
30
ThinkPad® T30 Series Service and Troubleshooting Guide
Upgrading the hard disk drive
5. Open the computer display; then stand the computer on its side and
remove the hard disk drive by pulling the cover away from the
computer.
6. Detach the cover from the hard disk drive.
7. Attach the cover to a new hard disk drive.
8. Insert the hard disk drive and its cover into the hard disk drive bay; then
firmly install them.
9. Turn the computer over so that its bottom side is up. Reinstall the screw.
Note: You can replace the screw with a security screw to prevent the
hard disk drive from being removed easily. The security screw
may not be included in your ship group. You can, however,
purchase screw directly from NABS at www.nabsnet.com
10. Reinstall the battery.
11. Turn the computer over again. Connect the ac adapter and the cables to
the computer.
Chapter 2. Solving computer problems
31
Replacing the battery
Replacing the battery
1. Turn off the computer, or enter hibernation mode. Then disconnect the ac
adapter and all cables from the computer.
Note: If you are using a PC Card, the computer might not be able to enter
hibernation mode. If this happens, turn off the computer.
2. Close the computer display, and turn the computer over.
3. Slide the battery latch to unlock it 1; then remove the battery 2.
Note: The first position of the battery latch is for releasing the lock of the
battery.
4. Align the side of a fully charged spare battery with the side of the battery
space in the computer 1; then gently push the battery into the space 2.
5. Slide the battery latch to lock it.
6. Turn the computer over again. Connect the ac adapter and the cables to
the computer.
32
ThinkPad® T30 Series Service and Troubleshooting Guide
Chapter 3. Getting help and service from IBM
Getting help and service .
Getting help on the Web .
Getting help by fax . .
© Copyright IBM Corp. 2002
. 34
. 34
. 35
Calling IBM . . . . . . .
Getting help around the world .
. 36
. 37
33
Getting help and service
Getting help and service
If you need help, service, technical assistance, or just want more information
about IBM products, you will find a wide variety of sources available from
IBM to assist you. This section contains information about where to go for
additional information about IBM and IBM products, what to do if you
experience a problem with your computer, and whom to call for service
should it be necessary.
Information about your IBM computer and preinstalled software, if any, is
available in the documentation that comes with your computer. That
documentation includes printed books, online books, README files, and help
files. In addition, information about IBM products is available on the World
Wide Web and through the IBM Automated Fax System.
For technical assistance with the installation of, or questions related to, Service
Packs for your preinstalled Microsoft Windows product, refer to the Microsoft
Product Support Services Web site at support.microsoft.com/directory/, or you
can contact the IBM HelpCenter®. Some fees might apply.
Getting help on the Web
On the World Wide Web, the IBM Web site has up-to-date information about
IBM Personal Computer products and support. The address for the IBM
Personal Computing home page is www.ibm.com/pc
IBM provides an extensive Web site dedicated to mobile computing and to
ThinkPad computers at www.ibm.com/pc/support
Research this Web site to learn how to solve problems, find new ways to use
your computer, and learn about options that can make working with your
ThinkPad computer even easier.
If you select Profile from the support page, you can create a customized
support page that is specific to your hardware, complete with Frequently
Asked Questions, Parts Information, Technical Hints and Tips, and
Downloadable Files. In addition, you can choose to receive e-mail notifications
whenever new information becomes available about your registered products.
You also can order publications through the IBM Publications Ordering
System at
www.elink.ibmlink.ibm.com/public/applications/publications/cgibin/pbi.cgi
34
ThinkPad® T30 Series Service and Troubleshooting Guide
Getting help and service
Getting help by fax
If you have a touch-tone telephone and access to a fax machine, in the U.S.
and Canada you can receive by fax marketing and technical information on
many topics, including hardware, operating systems, and local area networks
(LANs).
You can call the IBM Automated Fax System 24 hours a day, 7 days a week.
Follow the recorded instructions, and the requested information will be sent
to your fax machine. In the U.S. and Canada, to access the IBM Automated
Fax System, call 1-800-426-3395.
Calling IBM
If you have tried to correct the problem yourself and still need help, during
the warranty period, you can get help and information by telephone through
the IBM PC HelpCenter. The following services are available during the
warranty period:
v Problem determination - Trained personnel are available to assist you with
determining if you have a hardware problem and deciding what action is
necessary to fix the problem.
v IBM hardware repair - If the problem is determined to be caused by IBM
hardware under warranty, trained service personnel are available to provide
the applicable level of service.
v Engineering change management - Occasionally, there might be changes
that are required after a product has been sold. IBM or your reseller, if
authorized by IBM, will make selected Engineering Changes (ECs) available
that apply to your hardware.
The following items are not covered:
v Replacement or use of non-IBM parts or nonwarranted IBM parts
Note: All warranted parts contain a 7-character identification in the format
IBM FRU XXXXXXX
v Identification of software problem sources
v Configuration of BIOS as part of an installation or upgrade
v Changes, modifications, or upgrades to device drivers
v Installation and maintenance of network operating systems (NOS)
v Installation and maintenance of application programs
Refer to your IBM hardware warranty for a full explanation of IBM warranty
terms. Be sure to retain your proof of purchase to obtain warranty service.
Chapter 3. Getting help and service from IBM
35
Getting help and service
If possible, be near your computer when you make your call in case the
technical assistance representative needs to help you resolve a computer
problem. Please ensure that you have downloaded the most current drivers
and system updates, run diagnostics, and recorded information before you
call. When calling for technical assistance, please have the following
information available:
v Machine Type and Model
v Serial numbers of your computer, monitor, and other components, or your
proof of purchase
v Description of the problem
v Exact wording of any error messages
v Hardware and software configuration information for your system
Telephone numbers
Note: Telephone numbers are subject to change without notice. For the latest
list of IBM HelpCenter telephone numbers and hours of operation, visit
the Support Web site at www.ibm.com/pc/support
Country or region
Language
Telephone Number
Argentina
Spanish
0800-666-0011
Australia
English
1300-130-426
Austria
German
01-24592-5901
Bolivia
Spanish
0800-0189
Belgium
Dutch
02-210 9820
French
02-210 9800
Brazil
Portuguese
55-11-3889-8986
Canada
English/ French
1-800-565-3344
in Toronto only call
416-383-3344
36
Chile
Spanish
800-224-488
China
Mandarin
800-810-1818
Colombia
Spanish
980-912-3021
Denmark
Danish
45 20 82 00
Ecuador
Spanish
1-800-426911 (option #4)
Finland
Finnish
09-459 69 60
France
French
02 38 55 74 50
Germany
German
07032-1549 201
ThinkPad® T30 Series Service and Troubleshooting Guide
Getting help and service
Country or region
Language
Telephone Number
Hong Kong
Cantonese
2825-7799
Ireland
English
01-815 9200
Italy
Italian
02-7031-6101
Japan
Japanese
Luxembourg
French
298-977 5063
Mexico
Spanish
001-866-434-2080
Netherlands
Dutch
020-514 5770
New Zealand
English
0800-446-149
Norway
Norwegian
66 81 11 00
Peru
Spanish
0-800-50-866
Portugal
Portuguese
21-791 51 47
Russia
Russian
095-940-2000
Spain
Spanish
91-662 49 16
Sweden
Swedish
08-477 4420
Switzerland
German/
0583-33-09-00
French/
Italian
Taiwan
Mandarin
886-2-2725-9799
United
English
0-1475-555 055
United States
English
1-800-772-2227
Uruguay
Spanish
000-411-005-6649
Venezuela
Spanish
0-800-100-2011
Kingdom
Getting help around the world
If you travel with your computer or relocate it to a country where your
ThinkPad machine type is sold and serviced by IBM or by IBM resellers who
are authorized to perform warranty service, International Warranty Service is
available for your computer.
Service methods and procedures vary by country, and some services might
not be available in all countries. International Warranty Service is delivered
through the method of service (such as depot, carry-in, or on-site service) that
is provided in the servicing country. Service centers in certain countries might
Chapter 3. Getting help and service from IBM
37
Getting help and service
not be able to service all models of a particular machine type. In some
countries, fees and restrictions might apply at the time of service.
To determine whether your computer is eligible for International Warranty
Service and to view a list of the countries where service is available, go to
http://www.ibm.com/pc/support/, and click Warranty Lookup. Eligible IBM
computers are identified by their four-digit machine types. For more
information about International Warranty Service, see Service Announcement
601-034 at http://www.ibm.com/. Click Support & downloads, click
Announcement letters, and click Announcements search. In the Search by
letter number only field, type 601-034, and click Search.
38
ThinkPad® T30 Series Service and Troubleshooting Guide
Appendix A. Important safety instructions
DANGER
Electric current from power, telephone, and communication cables is hazardous. To
avoid shock hazard, connect and disconnect cables as shown below when
installing, moving, or opening the covers of this product or attached devices. If the
3-pin power cord is provided with this product, it must be used with a properly
grounded outlet.
To Connect
To Disconnect
Turn everything OFF.
Turn everything OFF.
First, attach all cables to devices.
First, remove the power cord from
the outlet.
Remove signal cables from
receptacles.
Attach the signal cables to
receptacles.
Remove all cables from devices.
Attach the power cord to an outlet.
Turn the device ON.
© Copyright IBM Corp. 2002
39
DANGER
Reduce the risk of fire and electric shock by always following basic safety
precautions, including the following:
v Do not use your computer in or near water.
v During electrical storms:
– Do not use your computer with the telephone cable connection.
– Do not connect the cable to or disconnect it from the telephone outlet on the
wall.
DANGER
If the rechargeable battery pack is incorrectly replaced, there is danger of an
explosion. The battery pack contains a small amount of harmful substances. To
avoid possible injury:
v Replace only with a battery of the type recommended by IBM.
v Keep the battery pack away from fire.
v Do not expose it to water or rain.
v Do not attempt to disassemble it.
v Do not short-circuit it.
v Keep it away from children.
Do not put the battery pack in trash that is disposed of in landfills. When
disposing of the battery, comply with local ordinances or regulations and your
company’s safety standards.
DANGER
If the backup battery is incorrectly replaced, there is danger of explosion.
The lithium battery contains lithium and can explode if it is not properly handled
or disposed of.
Replace only with a battery of the same type.
To avoid possible injury or death, do not: (1) throw or immerse the battery into
water, (2) allow it to heat to more than 100 °C (212 °F), or (3) attempt to repair or
disassemble it. Dispose of it as required by local ordinances or regulations and
your company’s safety standards.
40
ThinkPad® T30 Series Service and Troubleshooting Guide
DANGER Main battery safety notice
DANGER Backup battery safety notice
Appendix A. Important safety instructions
41
DANGER
Follow the instruction below when installing or reconfiguring the Mini PCI option.
To avoid shock hazard, disconnect all the cables and the ac adapter when you
install the Mini PCI option or open the covers of the system or attached devices.
Electrical current from power, telephone, and communication cables is hazardous.
CAUTION:
When you have added or upgraded a Mini PCI Card or a memory card, do
not use your computer until you have closed the cover. Never use the
computer when the cover is open.
CAUTION:
The fluorescent lamp in the liquid crystal display (LCD) contains mercury.
Do not put it in trash that is disposed of in landfills. Dispose of it as
required by local ordinances or regulations.
The LCD is made of glass, and rough handling or dropping the computer
can cause the LCD to break. If the LCD breaks and the internal fluid gets
into your eyes or on your hands, immediately wash the affected areas with
water for at least 15 minutes; if any symptoms are present after washing,
get medical care.
CAUTION:
To reduce the risk of fire, use only No. 26 AWG or larger (thicker)
telephone cable.
Modem safety information
To reduce the risk of fire, electrical shock, or injury when using telephone
equipment, always follow basic safety precautions, such as:
Never install telephone wiring during an electrical storm.
Never install telephone jacks in wet locations unless the jack is specifically
designed for wet locations.
Never touch uninsulated telephone wires or terminals unless the telephone
line has been disconnected at the network interface.
42
ThinkPad® T30 Series Service and Troubleshooting Guide
Use caution when installing or modifying telephone lines.
Avoid using a telephone (other than a cordless type) during an electrical
storm. There may be a remote risk of electric shock from lightning.
Do not use the telephone to report a gas leak in the vicinity of the leak.
Laser compliance statement
An optical storage drive (device), such as a CD-ROM, CD-RW, DVD-ROM
drive and SuperDisk, which can be installed in the IBM ThinkPad computer is
a laser product. The drive’s classification label (shown below) is on the surface
of the drive.
CLASS 1 LASER PRODUCT
LASER KLASSE 1
LUOKAN 1 LASERLAITE
APPAREIL A LASER DE CLASSE 1
KLASS 1 LASER APPARAT
The drive is certified by the manufacturer to comply with the requirements of
the Department of Health and Human Services 21 Code of Federal
Regulations (DHHS 21 CFR) Subchapter J for Class I laser products at the date
of manufacture.
In other countries, the drive is certified to conform to the requirements of
IEC825 and EN60825 for Class 1 laser products.
DANGER
Do not open the optical storage drive unit; no user adjustments or serviceable parts
are inside.
Use of controls, adjustments, or the performance of procedures other than those
specified might result in hazardous radiation exposure.
Class 1 laser products are not considered hazardous. The design of the laser
system and the optical storage drive ensures that there is no exposure to laser
radiation above a Class 1 level during normal operation, user maintenance, or
servicing.
Some drives contain an embedded Class 3A laser diode. Note this warning:
Appendix A. Important safety instructions
43
DANGER
Emits visible and invisible laser radiation when open. Avoid direct eye exposure.
Do not stare into the beam or view it directly with optical instruments.
Save these instructions.
44
ThinkPad® T30 Series Service and Troubleshooting Guide
Appendix B. Wireless related information
Wireless Interoperability
Wireless LAN Mini-PCI Adapter is designed to be interoperable with any
wireless LAN product that is based on Direct Sequence Spread Spectrum
(DSSS) radio technology, and is compliant to:
v The IEEE 802.11 Standard on Wireless LANs (Revision B), as defined and
approved by the Institute of Electrical and Electronics Engineers.
v The Wireless Fidelity (WiFi) certification as defined by the WECA (Wireless
Ethernet Compatibility Alliance).
IBM Bluetooth Daughter Card is designed to be interoperable with any
Bluetooth product that is compliant to Bluetooth Specification 1.1 as defined
by the Bluetooth SIG. Following profiles are supported by IBM Bluetooth
Daughter Card:
v Generic Access
Service Discovery
Serial Port
Dial-up Networking
FAX
LAN Access
Generic Object Exchange
v Generic Object Push
v File Transfer
v Synchronization
Usage environment and your Health
Wireless LAN Mini-PCI Adapter and Bluetooth Daughter Card emit radio
frequency electromagnetic energy like other radio devices. However, the level
of energy emitted is far much less than the electromagnetic energy emitted by
wireless devices like for example mobile phones.
Because Wireless LAN Mini-PCI Adapter and Bluetooth Daughter Card
operate within the guidelines found in radio frequency safety standards and
recommendations, IBM believes the integrated wireless cards are safe for use
by consumers. These standards and recommendations reflect the consensus of
© Copyright IBM Corp. 2002
45
the scientific community and result from deliberations of panels and
committees of scientists who continually review and interpret the extensive
research literature.
In some situation or environment, the use of Wireless LAN Mini-PCI Adapter
or Bluetooth Daughter Card may be restricted by the proprietor of the
building or responsible representatives of the organization. These situations
may for example include:
v Using the integrated wireless cards on board of airplanes, or in hospitals
v In any other environment where the risk of interference to other devices or
services is perceived or identified as harmful.
If you are uncertain of the policy that applies on the use of wireless devices in
a specific organization (e.g. airport or hospital), you are encouraged to ask for
authorization to use Wireless LAN Mini-PCI Adapter or Bluetooth Daughter
Card prior to turning on the ThinkPad T30 Series computer.
46
ThinkPad® T30 Series Service and Troubleshooting Guide
Appendix C. Wireless regulatory notice
The ThinkPad T30 Series computer must be installed and used in strict
accordance with the instructions as described hereafter. This product complies
with the following radio frequency and safety standards.
USA - Federal Communications Commissions (FCC)
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference
that may cause undesired operation.
The FCC RF Safety Requirement
The radiated output power of Wireless LAN Mini-PCI Adapter is far below
the FCC radio frequency exposure limits. Nevertheless, the ThinkPad T30
shall be used in such a manner that the potential for human contact during
normal operation is minimized as follows:
i) Multiple Transmitters model
If you find the FCC ID “ANOCORN1TASUHOP” on the label on the bottom
of your ThinkPad computer, your computer is approved as a Multiple
Transmitters device that is permitted to use two or more wireless option PC
Cards simultaneously with the integrated wireless features in your ThinkPad
computer.
The integrated wireless features (Wireless LAN Mini-PCI Adapter and
Bluetooth card) are preinstalled by IBM, and customers are not permitted to
use any other integrated wireless feature than those preinstalled modules. If
you will install an unauthorized module, your ThinkPad computer does not
start, but only displays an error message and emits beeps.
CAUTION:
To comply with FCC RF exposure compliance requirements, a separation
distance of at least 20 cm (8 inches) must be maintained between the
built-in antenna of this device and all persons.
© Copyright IBM Corp. 2002
47
Use of Wireless options
Please make sure of the following when you use a Bluetooth option or
wireless option PC Card in your ThinkPad computer.
1. Visit the IBM® site at www.ibm.com/pc/qtechinfo/MIGR-39377.html and
confirm the updated list of RF option devices that have been approved to
cooperate with the integrated wireless feature.
2. When you use any other RF option device that is not listed on the IBM
site, all other wireless features including the integrated transmitter in your
ThinkPad computer are required to be turned off.
3. Users are requested to follow the RF Safety instructions on wireless option
devices that are included in the RF option device’s user’s manual.
ii) Single Transmitter model
There is no FCC ID shown on the enclosure of this model. Instead you will
find an indicator pointing the location of the FCC ID at the bottom side of
your ThinkPad computer. If no integrated wireless LAN Mini-PCI Card has
been preinstalled in the computer, you can install one, provided by IBM as an
option.
Attention: If you install a wireless LAN Mini-PCI Card that is not authorized
for the ThinkPad T30 Series computer, the computer does not start, but only
displays an error message and emits four beeps.
CAUTION:
To comply with FCC RF exposure compliance requirements, a separation
48
ThinkPad® T30 Series Service and Troubleshooting Guide
distance of at least 20 cm (8 inches) must be maintained between the
built-in antenna of this device and all persons.
IBM High Rate Wireless LAN Mini-PCI Adapter with Modem II
(FCC ID: J3OM3AWEB56GA)
Cisco Aironet Wireless 802.11b (FCC ID: MCLU58H004)
Appendix C. Wireless regulatory notice
49
Note: The transmission diversity function is implemented for the Card. One
of the antennas is selected automatically or manually (by users) to have
good quality of radiocommunication.
Use of Wireless options
The FCC’s grant condition of the single transmitter model prohibits the use of
any other Radio Frequency wireless device in conjunction with the integrated
wireless LAN Mini-PCI Card in your ThinkPad computer. Do not use any
wireless option PC Card in the PC Card slot of your ThinkPad computer
while operating the integrated wireless LAN Mini-PCI Card.
Interference Statement
An improper installation or unauthorized use may cause harmful interference
to radio communications. Also any tampering of the internal antenna will
void the FCC certification and your warranty. Refer to the “Electronic
emission notices” on page 68 for more detail.
Canada - Industry Canada (IC)
Certification number
The term “IC” before the equipment certification number only signifies that
the Industry Canada technical specifications were met. The certification
number “IC: 349-CORN1BDC” on the label at the bottom of the computer is
for the integrated Bluetooth module. The number for the integrated wireless
LAN Mini-PCI Card is stuck on the Card installed in the Mini-PCI Card slot,
as shown below.
Attention: You can install or remove the wireless LAN Mini-PCI Card by
yourself. If you install a wireless LAN Mini-PCI Card that is not authorized
for the ThinkPad T30 Series computer, the computer does not start, but only
displays an error message and emits four beeps.
50
ThinkPad® T30 Series Service and Troubleshooting Guide
Low Power License-Exempt Radiocommunication Devices (RSS-210)
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Numéro d’homologation signifie
Le terme «IC» avant le numéro d’homologation signifie seulement que les
normes d’Industrie Canada ont été respectées.
Permis d’émission à faible puissance - Cas des appareils de communications
radio (CNR-210)
Le fonctionnement de ce type d’appareil est soumis aux deux conditions
suivantes: (1) Cet appareil peut perturber les communications radio, et (2) cet
appareil doit supporter toute perturbation, y compris les perturbations qui
pourraient provoquer un dysfonctionnement.
Notice for Users in Singapore
The Wireless LAN adapter included in this equipment is for use only within
the confined area of a building. The equipment is restricted to operating
within the 2445 - 2483.5 MHz band.
Appendix C. Wireless regulatory notice
51
52
ThinkPad® T30 Series Service and Troubleshooting Guide
Appendix D. Warranty information
This appendix contains warranty information for your ThinkPad, warranty
period, warranty service and support, and the IBM Statement of Limited
Warranty.
Warranty Period
Contact your place of purchase for warranty service information. Some IBM
Machines are eligible for on-site warranty service depending on the country
or region where service is performed or the machine type.
Machine type 2366
Country or region
Warranty period
Japan and Korea
Parts - 1 year, labor - 1 year
Battery pack - 1 year
All except Japan and Korea
Parts - 3 years, labor - 3 years
Battery pack - 1 year
Machine type 2367
Country or region
Warranty period
All
Parts - 3 years, labor - 3 years
Battery pack - 1 year
Warranty service and support
With the original purchase of an IBM ThinkPad, you have access to extensive
support. During the IBM Machine warranty period, you may call IBM or your
reseller for problem-determination assistance under the terms of the IBM
Statement of Limited Warranty.
The following services are available during the warranty period:
v Problem determination - Trained personnel are available to assist you with
determining if you have a hardware problem and deciding what action is
necessary to fix the problem.
© Copyright IBM Corp. 2002
53
v IBM hardware repair - If the problem is determined to be caused by IBM
hardware under warranty, trained service personnel are available to provide
the applicable level of service, either on-site or at an IBM service center as
determined by IBM.
v Engineering Change management - Occasionally, there might be changes
that are required after a product has been shipped from IBM. In those
instances, IBM will make Engineering Changes (ECs) available that apply to
your hardware.
The following items are not covered under warranty service:
v Replacement or use of non-IBM parts. All IBM parts contain a 7-character
identification in the format IBM FRU XXXXXXX.
v Identification of non-IBM software problem sources.
v Installation of customer replaceable units (CRUs).
v Installation and configuration of machine code or licensed internal code
that is designated as customer installable.
If you do not register your computer with IBM, you might be required to
present proof of purchase to obtain warranty service.
Before you call for service
You can solve many problems without outside assistance by following the
troubleshooting procedures that IBM provides in the online help or in the
publications that are provided with your computer and software.
Most computers, operating systems, and application programs come with
information that contains troubleshooting procedures and explanations of
error messages and error codes. The information that comes with your
computer also describes the diagnostic tests that you can perform.
If you suspect a software problem, refer to the information for the operating
system or application program.
Calling for service
Please have the following information ready:
v Machine type, model, and serial number
v Description of the problem
v Exact wording of any error messages
v Hardware and software configuration information
To find the telephone number for the HelpCenter nearest you, see “Telephone
numbers” in Chapter 3, “Getting help and service from IBM” on page 33
54
ThinkPad® T30 Series Service and Troubleshooting Guide
IBM Statement of Limited Warranty Z125-4753-06 8/2000
This warranty statement consists of two parts: Part 1 and Part 2. Be sure to
read Part 1 and the country-unique terms in Part 2 that apply to your country
or region.
Part 1 - General Terms
This Statement of Limited Warranty includes Part 1 - General Terms and Part
2 - Country-unique Terms. The terms of Part 2 replace or modify those of Part
1. The warranties provided by IBM in this Statement of Limited Warranty
apply only to Machines you purchase for your use, and not for resale, from
IBM or your reseller. The term “Machine” means an IBM machine, its features,
conversions, upgrades, elements, or accessories, or any combination of them.
The term “Machine” does not include any software programs, whether
pre-loaded with the Machine, installed subsequently or otherwise. Unless IBM
specifies otherwise, the following warranties apply only in the country where
you acquire the Machine. Nothing in this Statement of Limited Warranty
affects any statutory rights of consumers that cannot be waived or limited by
contract. If you have any questions, contact IBM or your reseller.
The IBM Warranty for Machines
IBM warrants that each Machine 1) is free from defects in materials and
workmanship and 2) conforms to IBM’s Official Published Specifications
(“Specifications”). The warranty period for a Machine is a specified, fixed
period commencing on its Date of Installation. The date on your sales receipt
is the Date of Installation unless IBM or your reseller informs you otherwise.
If a Machine does not function as warranted during the warranty period, and
IBM or your reseller are unable to either 1) make it do so or 2) replace it with
one that is at least functionally equivalent, you may return it to your place of
purchase and your money will be refunded.
Extent of Warranty
The warranty does not cover the repair or exchange of a Machine resulting
from misuse, accident, modification, unsuitable physical or operating
environment, improper maintenance by you, or failure caused by a product
for which IBM is not responsible. The warranty is voided by removal or
alteration of Machine or parts identification labels.
THESE WARRANTIES ARE YOUR EXCLUSIVE WARRANTIES AND
REPLACE ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. THESE WARRANTIES GIVE
YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER
RIGHTS WHICH VARY FROM JURISDICTION TO JURISDICTION.
SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR
Appendix D. Warranty information
55
LIMITATION OF EXPRESS OR IMPLIED WARRANTIES, SO THE ABOVE
EXCLUSION OR LIMITATION MAY NOT APPLY TO YOU. IN THAT
EVENT, SUCH WARRANTIES ARE LIMITED IN DURATION TO THE
WARRANTY PERIOD. NO WARRANTIES APPLY AFTER THAT PERIOD.
Items Not Covered by Warranty
IBM does not warrant uninterrupted or error-free operation of a Machine.
Any technical or other support provided for a Machine under warranty, such
as assistance via telephone with “how-to” questions and those regarding
Machine set-up and installation, will be provided WITHOUT WARRANTIES
OF ANY KIND.
Warranty Service
To obtain warranty service for a Machine, contact IBM or your reseller. If you
do not register your Machine with IBM, you may be required to present proof
of purchase.
During the warranty period, IBM or your reseller, if approved by IBM to
provide warranty service, provides without charge certain types of repair and
exchange service to keep Machines in, or restore them to, conformance with
their Specifications. IBM or your reseller will inform you of the available
types of service for a Machine based on its country of installation. At its
discretion, IBM or your reseller will 1) either repair or exchange the failing
Machine and 2) provide the service either at your location or a service center.
IBM or your reseller will also manage and install selected engineering changes
that apply to the Machine.
Some parts of IBM Machines are designated as Customer Replaceable Units
(called “CRUs”), e.g., keyboards, memory, or hard disk drives. IBM ships
CRUs to you for replacement by you. You must return all defective CRUs to
IBM within 30 days of your receipt of the replacement CRU. You are
responsible for downloading designated Machine Code and Licensed Internal
Code updates from an IBM Internet Web site or from other electronic media,
and following the instructions that IBM provides.
When warranty service involves the exchange of a Machine or part, the item
IBM or your reseller replaces becomes its property and the replacement
becomes yours. You represent that all removed items are genuine and
unaltered. The replacement may not be new, but will be in good working
order and at least functionally equivalent to the item replaced. The
replacement assumes the warranty service status of the replaced item. Many
features, conversions, or upgrades involve the removal of parts and their
return to IBM. A part that replaces a removed part will assume the warranty
service status of the removed part.
56
ThinkPad® T30 Series Service and Troubleshooting Guide
Before IBM or your reseller exchanges a Machine or part, you agree to remove
all features, parts, options, alterations, and attachments not under warranty
service.
You also agree to
1. ensure that the Machine is free of any legal obligations or restrictions that
prevent its exchange;
2. obtain authorization from the owner to have IBM or your reseller service a
Machine that you do not own; and
3. where applicable, before service is provided:
a. follow the problem determination, problem analysis, and service
request procedures that IBM or your reseller provides;
b. secure all programs, data, and funds contained in a Machine;
c. provide IBM or your reseller with sufficient, free, and safe access to
your facilities to permit them to fulfill their obligations; and
d. inform IBM or your reseller of changes in a Machine’s location.
IBM is responsible for loss of, or damage to, your Machine while it is 1) in
IBM’s possession or 2) in transit in those cases where IBM is responsible for
the transportation charges.
Neither IBM nor your reseller is responsible for any of your confidential,
proprietary or personal information contained in a Machine which you return
to IBM or your reseller for any reason. You should remove all such
information from the Machine prior to its return.
Limitation of Liability
Circumstances may arise where, because of a default on IBM’s part or other
liability, you are entitled to recover damages from IBM. In each such instance,
regardless of the basis on which you are entitled to claim damages from IBM
(including fundamental breach, negligence, misrepresentation, or other
contract or tort claim), except for any liability that cannot be waived or
limited by applicable laws, IBM is liable for no more than
1. damages for bodily injury (including death) and damage to real property
and tangible personal property; and
2. the amount of any other actual direct damages, up to the charges (if
recurring, 12 months’ charges apply) for the Machine that is subject of the
claim. For purposes of this item, the term “Machine” includes Machine
Code and Licensed Internal Code.
This limit also applies to IBM’s suppliers and your reseller. It is the maximum
for which IBM, its suppliers, and your reseller are collectively responsible.
Appendix D. Warranty information
57
UNDER NO CIRCUMSTANCES IS IBM LIABLE FOR ANY OF THE
FOLLOWING: 1) THIRD-PARTY CLAIMS AGAINST YOU FOR
DAMAGES (OTHER THAN THOSE UNDER THE FIRST ITEM LISTED
ABOVE); 2) LOSS OF, OR DAMAGE TO, YOUR RECORDS OR DATA; OR
3) SPECIAL, INCIDENTAL, OR INDIRECT DAMAGES OR FOR ANY
ECONOMIC CONSEQUENTIAL DAMAGES, LOST PROFITS OR LOST
SAVINGS, EVEN IF IBM, ITS SUPPLIERS OR YOUR RESELLER IS
INFORMED OF THEIR POSSIBILITY. SOME JURISDICTIONS DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR
EXCLUSION MAY NOT APPLY TO YOU.
Governing Law
Both you and IBM consent to the application of the laws of the country in
which you acquired the Machine to govern, interpret, and enforce all of your
and IBM’s rights, duties, and obligations arising from, or relating in any
manner to, the subject matter of this Agreement, without regard to conflict of
law principles.
Part 2 - Country-unique Terms
AMERICAS
BRAZIL
Governing Law: The following is added after the first sentence:
Any litigation arising from this Agreement will be settled exclusively by the
court of Rio de Janeiro.
NORTH AMERICA
Warranty Service: The following is added to this Section:
To obtain warranty service from IBM in Canada or the United States, call
1-800-IBM-SERV (426-7378).
CANADA
Governing Law: The following replaces “laws of the country in which you acquired
the Machine” in the first sentence:
laws in the Province of Ontario.
UNITED STATES
Governing Law: The following replaces “laws of the country in which you acquired
the Machine” in the first sentence:
laws of the State of New York.
58
ThinkPad® T30 Series Service and Troubleshooting Guide
ASIA PACIFIC
AUSTRALIA
The IBM Warranty for Machines: The following paragraph is added to this
Section:
The warranties specified in this Section are in addition to any rights you may
have under the Trade Practices Act 1974 or other similar legislation and are
only limited to the extent permitted by the applicable legislation.
Limitation of Liability: The following is added to this Section:
Where IBM is in breach of a condition or warranty implied by the Trade
Practices Act 1974 or other similar legislation, IBM’s liability is limited to the
repair or replacement of the goods or the supply of equivalent goods. Where
that condition or warranty relates to right to sell, quiet possession or clear
title, or the goods are of a kind ordinarily acquired for personal, domestic or
household use or consumption, then none of the limitations in this paragraph
apply.
Governing Law: The following replaces “laws of the country in which you acquired
the Machine” in the first sentence:
laws of the State or Territory.
CAMBODIA, LAOS, AND VIETNAM
Governing Law: The following replaces “laws of the country in which you acquired
the Machine” in the first sentence:
laws of the State of New York.
The following is added to this Section:
Disputes and differences arising out of or in connection with this Agreement
shall be finally settled by arbitration which shall be held in Singapore in
accordance with the rules of the International Chamber of Commerce (ICC).
The arbitrator or arbitrators designated in conformity with those rules shall
have the power to rule on their own competence and on the validity of the
Agreement to submit to arbitration. The arbitration award shall be final and
binding for the parties without appeal and the arbitral award shall be in
writing and set forth the findings of fact and the conclusions of law.
All proceedings shall be conducted, including all documents presented in
such proceedings, in the English language. The number of arbitrators shall be
three, with each side to the dispute being entitled to appoint one arbitrator.
The two arbitrators appointed by the parties shall appoint a third arbitrator
before proceeding upon the reference. The third arbitrator shall act as
chairman of the proceedings. Vacancies in the post of chairman shall be filled
Appendix D. Warranty information
59
by the president of the ICC. Other vacancies shall be filled by the respective
nominating party. Proceedings shall continue from the stage they were at
when the vacancy occurred.
If one of the parties refuses or otherwise fails to appoint an arbitrator within
30 days of the date the other party appoints its, the first appointed arbitrator
shall be the sole arbitrator, provided that the arbitrator was validly and
properly appointed.
The English language version of this Agreement prevails over any other
language version.
HONG KONG AND MACAU
Governing Law: The following replaces “laws of the country in which you acquired
the Machine” in the first sentence:
laws of Hong Kong Special Administrative Region.
INDIA
Limitation of Liability: The following replaces items 1 and 2 of this Section:
1. liability for bodily injury (including death) or damage to real property and
tangible personal property will be limited to that caused by IBM’s
negligence;
2. as to any other actual damage arising in any situation involving
nonperformance by IBM pursuant to, or in any way related to the subject
of this Statement of Limited Warranty, IBM’s liability will be limited to the
charge paid by you for the individual Machine that is the subject of the
claim.
JAPAN
Governing Law: The following sentence is added to this Section:
Any doubts concerning this Agreement will be initially resolved between us
in good faith and in accordance with the principle of mutual trust.
NEW ZEALAND
The IBM Warranty for Machines: The following paragraph is added to this
Section:
The warranties specified in this Section are in addition to any rights you may
have under the Consumer Guarantees Act 1993 or other legislation which
cannot be excluded or limited. The Consumer Guarantees Act 1993 will not
apply in respect of any goods which IBM provides, if you require the goods
for the purposes of a business as defined in that Act.
60
ThinkPad® T30 Series Service and Troubleshooting Guide
Limitation of Liability: The following is added to this Section:
Where Machines are not acquired for the purposes of a business as defined in
the Consumer Guarantees Act 1993, the limitations in this Section are subject
to the limitations in that Act.
PEOPLE’S REPUBLIC OF CHINA (PRC)
Governing Law: The following replaces this Section:
Both you and IBM consent to the application of the laws of the State of New
York (except when local law requires otherwise) to govern, interpret, and
enforce all your and IBM’s rights, duties, and obligations arising from, or
relating in any manner to, the subject matter of this Agreement, without
regard to conflict of law principles.
Any disputes arising from or in connection with this Agreement will first be
resolved by friendly negotiations, failing which either of us has the right to
submit the dispute to the China International Economic and Trade Arbitration
Commission in Beijing, the PRC, for arbitration in accordance with its
arbitration rules in force at the time. The arbitration tribunal will consist of
three arbitrators. The language to be used therein will be English and Chinese.
An arbitral award will be final and binding on all the parties, and will be
enforceable under the Convention on the Recognition and Enforcement of
Foreign Arbitral Awards (1958).
The arbitration fee will be borne by the losing party unless otherwise
determined by the arbitral award.
During the course of arbitration, this Agreement will continue to be
performed except for the part which the parties are disputing and which is
undergoing arbitration.
EUROPE, MIDDLE EAST, AFRICA (EMEA)
THE FOLLOWING TERMS APPLY TO ALL EMEA COUNTRIES:
The terms of this Statement of Limited Warranty apply to Machines purchased
from IBM or an IBM reseller.
Warranty Service:
If you purchase an IBM Machine in Austria, Belgium, Denmark, Estonia,
Finland, France, Germany, Greece, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland or
United Kingdom, you may obtain warranty service for that Machine in any of
those countries from either (1) an IBM reseller approved to perform warranty
service or (2) from IBM. If you purchase an IBM Personal Computer Machine
in Albania, Armenia, Belarus, Bosnia and Herzegovina, Bulgaria, Croatia,
Czech Republic, Georgia, Hungary, Kazakhstan, Kirghizia, Federal Republic of
Appendix D. Warranty information
61
Yugoslavia, Former Yugoslav Republic of Macedonia (FYROM), Moldova,
Poland, Romania, Russia, Slovak Republic, Slovenia, or Ukraine, you may
obtain warranty service for that Machine in any of those countries from either
(1) an IBM reseller approved to perform warranty service or (2) from IBM.
If you purchase an IBM Machine in a Middle Eastern or African country, you
may obtain warranty service for that Machine from the IBM entity within the
country of purchase, if that IBM entity provides warranty service in that
country, or from an IBM reseller, approved by IBM to perform warranty
service on that Machine in that country. Warranty service in Africa is available
within 50 kilometers of an IBM authorized service provider. You are
responsible for transportation costs for Machines located outside 50 kilometers
of an IBM authorized service provider.
Governing Law:
The applicable laws that govern, interpret and enforce rights, duties, and
obligations of each of us arising from, or relating in any manner to, the
subject matter of this Statement, without regard to conflict of laws principles,
as well as Country-unique terms and competent court for this Statement are
those of the country in which the warranty service is being provided, except
that in 1) Albania, Bosnia-Herzegovina, Bulgaria, Croatia, Hungary, Former
Yugoslav Republic of Macedonia, Romania, Slovakia, Slovenia, Armenia,
Azerbaijan, Belarus, Georgia, Kazakhstan, Kyrgyzstan, Moldova, Russia,
Tajikistan, Turkmenistan, Ukraine, and Uzbekistan, the laws of Austria apply;
2) Estonia, Latvia, and Lithuania, the laws of Finland apply; 3) Algeria, Benin,
Burkina Faso, Cameroon, Cape Verde, Central African Republic, Chad, Congo,
Djibouti, Democratic Republic of Congo, Equatorial Guinea, France, Gabon,
Gambia, Guinea, Guinea-Bissau, Ivory Coast, Lebanon, Mali, Mauritania,
Morocco, Niger, Senegal, Togo, and Tunisia, this Agreement will be construed
and the legal relations between the parties will be determined in accordance
with the French laws and all disputes arising out of this Agreement or related
to its violation or execution, including summary proceedings, will be settled
exclusively by the Commercial Court of Paris; 4) Angola, Bahrain, Botswana,
Burundi, Egypt, Eritrea, Ethiopia, Ghana, Jordan, Kenya, Kuwait, Liberia,
Malawi, Malta, Mozambique, Nigeria, Oman, Pakistan, Qatar, Rwanda, Sao
Tome, Saudi Arabia, Sierra Leone, Somalia, Tanzania, Uganda, United Arab
Emirates, United Kingdom, West Bank/Gaza, Yemen, Zambia, and Zimbabwe,
this Agreement will be governed by English Law and disputes relating to it
will be submitted to the exclusive jurisdiction of the English courts; and 5) in
Greece, Israel, Italy, Portugal, and Spain any legal claim arising out of this
Statement will be brought before, and finally settled by, the competent court
of Athens, Tel Aviv, Milan, Lisbon, and Madrid, respectively.
THE FOLLOWING TERMS APPLY TO THE COUNTRY SPECIFIED:
AUSTRIA AND GERMANY
62
ThinkPad® T30 Series Service and Troubleshooting Guide
The IBM Warranty for Machines: The following replaces the first sentence of the
first paragraph of this Section:
The warranty for an IBM Machine covers the functionality of the Machine for
its normal use and the Machine’s conformity to its Specifications.
The following paragraphs are added to this Section:
The minimum warranty period for Machines is six months. In case IBM or
your reseller is unable to repair an IBM Machine, you can alternatively ask for
a partial refund as far as justified by the reduced value of the unrepaired
Machine or ask for a cancellation of the respective agreement for such
Machine and get your money refunded.
Extent of Warranty: The second paragraph does not apply.
Warranty Service: The following is added to this Section:
During the warranty period, transportation for delivery of the failing Machine
to IBM will be at IBM’s expense.
Limitation of Liability: The following paragraph is added to this Section:
The limitations and exclusions specified in the Statement of Limited Warranty
will not apply to damages caused by IBM with fraud or gross negligence and
for express warranty.
The following sentence is added to the end of item 2:
IBM’s liability under this item is limited to the violation of essential
contractual terms in cases of ordinary negligence.
EGYPT
Limitation of Liability: The following replaces item 2 in this Section:
as to any other actual direct damages, IBM’s liability will be limited to the
total amount you paid for the Machine that is the subject of the claim. For
purposes of this item, the term “Machine” includes Machine Code and
Licensed Internal Code.
Applicability of suppliers and resellers (unchanged).
FRANCE
Limitation of Liability: The following replaces the second sentence of the first
paragraph of this Section:
In such instances, regardless of the basis on which you are entitled to claim
damages from IBM, IBM is liable for no more than: (items 1 and 2 unchanged).
IRELAND
Appendix D. Warranty information
63
Extent of Warranty: The following is added to this Section:
Except as expressly provided in these terms and conditions, all statutory
conditions, including all warranties implied, but without prejudice to the
generality of the foregoing all warranties implied by the Sale of Goods Act
1893 or the Sale of Goods and Supply of Services Act 1980 are hereby
excluded.
Limitation of Liability: The following replaces items one and two of the first
paragraph of this Section:
1. death or personal injury or physical damage to your real property solely
caused by IBM’s negligence; and
2. the amount of any other actual direct damages, up to 125 percent of the
charges (if recurring, the 12 months’ charges apply) for the Machine that is
the subject of the claim or which otherwise gives rise to the claim.
Applicability of suppliers and resellers (unchanged).
The following paragraph is added at the end of this Section:
IBM’s entire liability and your sole remedy, whether in contract or in tort, in
respect of any default shall be limited to damages.
ITALY
Limitation of Liability: The following replaces the second sentence in the first
paragraph:
In each such instance unless otherwise provided by mandatory law, IBM is
liable for no more than:
1. (unchanged)
2. as to any other actual damage arising in all situations involving
nonperformance by IBM pursuant to, or in any way related to the subject
matter of this Statement of Warranty, IBM’s liability, will be limited to the
total amount you paid for the Machine that is the subject of the claim.
Applicability of suppliers and resellers (unchanged).
The following replaces the third paragraph of this Section:
Unless otherwise provided by mandatory law, IBM and your reseller are not
liable for any of the following: (items 1 and 2 unchanged) 3) indirect damages,
even if IBM or your reseller is informed of their possibility.
SOUTH AFRICA, NAMIBIA, BOTSWANA, LESOTHO AND SWAZILAND
Limitation of Liability: The following is added to this Section:
IBM’s entire liability to you for actual damages arising in all situations
involving nonperformance by IBM in respect of the subject matter of this
64
ThinkPad® T30 Series Service and Troubleshooting Guide
Statement of Warranty will be limited to the charge paid by you for the
individual Machine that is the subject of your claim from IBM.
UNITED KINGDOM
Limitation of Liability: The following replaces items 1 and 2 of the first paragraph
of this Section:
1. death or personal injury or physical damage to your real property solely
caused by IBM’s negligence;
2. the amount of any other actual direct damages or loss, up to 125 percent
of the charges (if recurring, the 12 months’ charges apply) for the Machine
that is the subject of the claim or which otherwise gives rise to the claim;
The following item is added to this paragraph:
3. breach of IBM’s obligations implied by Section 12 of the Sale of Goods Act
1979 or Section 2 of the Supply of Goods and Services Act 1982.
Applicability of suppliers and resellers (unchanged).
The following is added to the end of this Section:
IBM’s entire liability and your sole remedy, whether in contract or in tort, in
respect of any default shall be limited to damages.
Appendix D. Warranty information
65
66
ThinkPad® T30 Series Service and Troubleshooting Guide
Appendix E. Notices
This publication was developed for products and services offered in the
U.S.A.
IBM may not offer the products, services, or features discussed in this
document in other countries. Consult your local IBM representative for
information on the products and services currently available in your area. Any
reference to an IBM product, program, or service is not intended to state or
imply that only that IBM product, program, or service may be used. Any
functionally equivalent product, program, or service that does not infringe
any IBM intellectual property right may be used instead. However, it is the
user’s responsibility to evaluate and verify the operation of any non-IBM
product, program, or service.
IBM may have patents or pending patent applications covering subject matter
described in this document. The furnishing of this document does not give
you any license to these patents. You can send license inquiries, in writing, to:
IBM Director of Licensing
IBM Corporation
North Castle Drive
Armonk, NY 10504-1785
U.S.A.
Processing date data
This IBM hardware product and IBM software products that might be
packaged with it have been designed, when used in accordance with their
associated documentation, to process date data correctly within and between
the 20th and 21st centuries, provided all other products (for example,
software, hardware, and firmware) used with these products properly
exchange accurate date data with them.
IBM cannot take responsibility for the date data processing capabilities of
non-IBM products, even if those products are preinstalled or otherwise
distributed by IBM. You should contact the vendors responsible for those
products directly to determine the capabilities of their products and update
them if needed. This IBM hardware product cannot prevent errors that might
occur if software, upgrades, or peripheral devices you use or exchange data
with do not process date data correctly.
The foregoing is a Year 2000 Readiness Disclosure.
© Copyright IBM Corp. 2002
67
References to the Web site addresses
Any references in this publication to non-IBM Web sites are provided for
convenience only and do not in any manner serve as an endorsement of those
Web sites. The materials at those Web sites are not part of the materials for
this IBM product, and use of those Web sites is at your own risk.
Electronic emission notices
Federal Communications Commission (FCC) Statement
ThinkPad T30, machine type 2366 or 2367
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
v Reorient or relocate the receiving antenna.
v Increase the separation between the equipment and receiver.
v Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
v Consult an IBM authorized dealer or service representative for help.
Properly shielded and grounded cables and connectors must be used in order
to meet FCC emission limits. Proper cables and connectors are available from
IBM authorized dealers. IBM is not responsible for any radio or television
interference caused by using other than recommended cables and connectors
or by unauthorized changes or modifications to this equipment. Unauthorized
changes or modifications could void the user’s authority to operate the
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Responsible Party:
68
ThinkPad® T30 Series Service and Troubleshooting Guide
International Business Machines Corporation
New Orchard Road
Armonk, NY 10504
Telephone 1-919-543-2193
Industry Canada Class B Emission Compliance Statement
This Class B digital apparatus complies with Canadian ICES-003.
Avis de conformité à la réglementation d’Industrie Canada
Cet appareil numérique de la classe B est conform à la norme NMB-003 du
Canada.
European Community Directive Conformance Statement
This product is in conformity with the protection requirements of EU Council
Directive 89/336/EEC on the approximation of the laws of the Member States
relating to electro-magnetic compatibility. IBM cannot accept responsibility for
any failure to satisfy the protection requirements resulting from a
non-recommended modification of the product, including the fitting of
non-IBM option cards.
This product satisfies the Class B limits of EN 55022.
Telecommunication notices
Federal Communications Commission (FCC) and Telephone Company
Requirements (Part 68 of the FCC Rules)
1. The Telephone Consumer Protection Act of 1991 makes it unlawful for any
person to use a computer or other electronic device to send any message
via a telephone fax machine unless such message clearly contains in a
margin at the top or bottom of each transmitted page or on the first page
of the transmission, the date and time it is sent, and an identification of
the business or other entity, or other individual sending the message and
the telephone number of the sending machine or such business, other
entity, or individual.
In order to program this information into your computer, you should be
sure to follow the installation instructions for your fax software package.
2. The built-in modem is built into the ThinkPad computer. It complies with
Part 68 of the FCC Rules. A label is affixed to the bottom of the computer
that contains, among other things, the FCC registration number, USOC,
Appendix E. Notices
69
and Ringer Equivalency Number (REN) for this equipment. If these
numbers are requested, look at the label and provide this information to
your telephone company.
3. The REN is useful to determine the quantity of devices you may connect
to your telephone line and still have those devices ring when your number
is called. In most, but not all, areas, the sum of the RENs of all devices
should not exceed five (5.0). To be certain of the number of devices you
may connect to your line, as determined by the REN (REN:0.7), you
should call your local telephone company to determine the maximum REN
for your calling area.
4. If the built-in modem causes harm to the telephone network, the telephone
company may discontinue your service temporarily. If possible, they will
notify you in advance. But, if advance notice isn’t practical, you will be
notified as soon as possible. You will be advised of your right to file a
complaint with the FCC.
5. Your telephone company may make changes in its facilities, equipment,
operations, or procedures that could affect the proper operation of your
equipment. If they do, you will be given advance notice so as to give you
an opportunity to maintain uninterrupted service.
6. If you experience trouble with this built-in modem, contact your IBM
Authorized Seller, or the IBM Corporation, 500 Columbus Avenue,
Thornwood, NY 10594, 1-800-772-2227, for repair/warranty information.
The telephone company may ask you to disconnect this equipment from
the network until the problem has been corrected, or until you are sure the
equipment is not malfunctioning.
7. No customer repairs are possible to the modem. If you experience trouble
with this equipment, contact your Authorized Seller or the IBM
Corporation for information.
8. The modem may not be used on coin service provided by the telephone
company. Connection to party lines is subject to state tariffs. Contact your
state public utility commission or corporation commission for information.
9. When ordering network interface (NI) service from the Local Exchange
Carrier, specify service arrangement USOC RJ11C.
Fax Branding
The Telephone Consumer Protection Act of 1991 makes it unlawful for any
person to use a computer or other electronic device, including fax machines,
to send any message unless such message clearly contains in a margin at the
top of or bottom of each transmitted page or on the first page of the
transmission, the date and time it is sent and an identification of the business
or other entity, or other individual sending the message and the telephone
number of the sending machine or such business, other entity, or individual.
(The telephone number provided may not be a 900 number or any other
number for which charges exceed local or long-distance transmission charges.)
70
ThinkPad® T30 Series Service and Troubleshooting Guide
Industry Canada requirements
Notice
The Industry Canada label identifies certified equipment. This certification
means that the equipment meets certain telecommunications networks
protective, operational, and safety requirements. The Department does not
guarantee the equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to
be connected to the facilities of the local telecommunications company. The
equipment must also be installed using an acceptable method of
communication. In some cases, the company’s inside wiring associated with a
single line individual service may be extended by means of a certified
connector assembly (telephone extension cord). The customer should be aware
that compliance with the above conditions may not prevent degradation of
service in some situations.
Repairs to certified equipment should be made by an authorized Canadian
maintenance facility designated by the supplier. Any repairs of alterations
made by the user to this equipment, or equipment malfunctions, may give the
telecommunications company cause to request the user to disconnect the
equipment.
Users should ensure for their own protection that the electrical ground
connections of the power utility, telephone lines and internal metallic water
pipe system, if present, are connected together. This precaution may be
particularly important in rural areas.
Caution
Users should not attempt to make such connections themselves, but should
contact the appropriate electric inspection authority, or electrician, as
appropriate.
The Ringer Equivalent Number (REN:0.3) assigned to each terminal device
provides an indication of the maximum number of terminals allowed to be
connected to a telephone interface. The termination on an interface may
consist of any combination of devices subject only to the requirement that the
sum of the Ringer Equivalence Number of all the devices does not exceed 5.
Avis
L’étiquette du ministère de l’Industrie Canada identifie le matériel homologué.
Cette étiquette certifie que le matériel est conforme à certaines normes de
protection, d’exploitation et de sécurité des réseaux de télécommunications. Le
Ministère n’assure toutefois pas que le matériel fonctionnera à la satisfaction
de l’utilisateur.
Appendix E. Notices
71
Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il est permis de le
raccorder aux installations de l’entreprise locale de télécommunication. Le
matériel doit également être installé en suivant une méthode acceptée de
raccordement. Dans certains cas, les fils intérieurs de l’entreprise utilisés pour
un service individuel à ligne unique peuvent être prolongés au moyen d’un
dispositif homologué de raccordement (cordon prolongateur téléphonique
interne). L’abonné ne doit pas oublier qu’il est possible que la conformité aux
conditions énoncées ci-dessus n’empechent pas la dégradation du service dans
certaines situations. Actuellement, les entreprises de télécommunication ne
permettent pas que l’on raccorde leur matériel à des jacks d’abonné, sauf dans
les cas précis prévus par les tarifs paticuliers de ces entreprises.
Les réparations de matériel homologué doivent être effectuées par un centre
d’entretien canadien autorisé désigné par le fournisseur. La compagnie de
télécommunications peut demander à l’utilisateur de débrancher un appareil à
la suite de réparations ou de modifications effectuées par l’utilisateur ou à
cause de mauvais fonctionnement.
Pour sa propre protection, l’utilisateur doit s’assurer que tous les fils de mise
à la terre de la source d’énergie électrique, des lignes téléphoniques et des
canalisations d’eau métalliques, s’il y en a, sont raccordés ensemble. Cette
précaution est particulièrement importante dans les régions rurales.
Avertissement
L’utilisateur ne doit pas tenter de faire ces raccordements lui-même; il doit
avoir recours à un service d’inspection des installations électriques, ou à
électricien, selon le cas.
L’indice de charge (IC) assigné à chaque dispositif terminal indique (REN:0.3),
pour éviter toute surcharge, le pourcentage de la charge totale qui peut être
raccordée à un circuit téléphonique bouclé utilisé par ce dispositif. La
terminaison du circuit bouclé peut être constituée de n’importe quelle
combinaison de dispositifs, pourvu que la somme des indices de charge de
l’ensemble des dispositifs ne dépasse pas 5.
Notice for Australia
The following notice applies when using the telephony functions:
WARNING: FOR SAFETY REASONS, ONLY CONNECT EQUIPMENT WITH A
TELECOMMUNICATIONS COMPLIANCE LABEL. THIS INCLUDES CUSTOMER
EQUIPMENT PREVIOUSLY LABELLED PERMITTED OR CERTIFIED.
72
ThinkPad® T30 Series Service and Troubleshooting Guide
Notice for New Zealand
For the modem with approval number PTC 211/00/206
1. The grant of a Telepermit for any item of terminal equipment indicates
only that Telecom has accepted that the item complies with minimum
conditions for connection to its network. It indicates no endorsement of
the product by Telecom, nor does it provide any sort of warranty. Above
all, it provides no assurance that any item will work correctly in all
respects with another item of Telepermitted equipment of a different make
or model, nor does it imply that any product is compatible with all of
Telecom’s network services.
2. This equipment is not capable under all operation conditions of correct
operation at the higher speeds for which it is designed. The 33.6 kbit/s
and 56 kbit/s connections are likely to be restricted to lower bit rates
when connected to some PSTN implementations. Telecom will accept no
responsibility should difficulties arise in such circumstances.
3. This equipment may not provide for the effective hand-over of a call to
another device connected to the same line.
4. Under power failure conditions, this telephone may not operate. Please
ensure that a separate telephone, not dependent on local power is
available for emergency use.
5. Some parameters required for compliance with Telecom’s Telepermit
requirements are dependent on the equipment (PC) associated with this
device. The associated equipment shall be set to operate within the
following limits for compliance with Telecom’s specifications:
v There shall be no more than 10 call attempts to the same number within
any 30-minute period for any single manual call initiation.
v The equipment shall go on-hook for a period of not less than 30 seconds
between the end of one attempt and the beginning of the next attempt
to the same number.
6. Some parameters required for compliance with Telecom’s Telepermit
requirements are dependent on the equipment (PC) associated with this
device. In order to operate within the limits for compliance with Telecom’s
specifications, the associated equipment shall be set to ensure that
automatic calls to different numbers are spaced such that there is no less
than 5 seconds between the end of one call attempt and the beginning of
another.
7. This equipment shall not be set up to make automatic calls to Telecom’s
’111’ emergency service.
8. Some parameters required for compliance with Telecom’s Telepermit
requirements are dependent on the equipment (PC) associated with this
device. In order to operate within the limits for compliance with Telecom’s
specifications, the associated equipment shall be set to ensure that calls are
answered between 3 and 30 seconds of receipt of ringing.
Appendix E. Notices
73
For the modem with approval number PTC 211/01/004
The grant of a Telepermit for any item of terminal equipment indicates only
that Telecom has accepted that the item complies with minimum conditions
for connection to its network. It indicates no endorsement of the product by
Telecom, nor does it provide any sort of warranty. Above all, it provides no
assurance that any item will work correctly in all respects with another item
of Telepermitted equipment of a different make or model, nor does it imply
that any product is compatible with all of Telecom’s network services.
Some parameters required for compliance with Telecom’s Telepermit
requirements are dependent on the equipment (PC) associated with this
device. The associated equipment shall be set to operate within the following
limits for compliance with Telecom’s Specification:
v There shall be no more than 10 call attempts to the same number within
any 30 minute period for any single manual call initiation, and
v The equipment shall go offline for a period of not less than 30 seconds
between the end of one call attempt and the beginning of the next attempt.
Where automatic calls are made to different numbers, the equipment shall
go offline for a period of not less than 5 seconds between the end of one
call attempt and the beginning of the next attempt.
v When used in the automatic answer mode, the equipment shall be set to
answer within 3 to 30 seconds of the receipt of ringing.
This equipment shall not be set-up to make automatic calls to the Telecom 111
emergency service.
For the modem with approval number PTC 211/99/255
Not all phones connected to the phone port will respond to incoming ringing.
Do not report this as a fault unless the same phone will not respond to
ringing when connected to a standard phone socket.
This equipment shall not be set up to make automatic calls to the Telecom 111
Emergency Services.
The grant of a Telepermit for a device in no way indicates Telecom acceptance
of responsibility for the correct operation of that device under all operating
conditions. In particular, higher speeds at which this modem is capable of
operating depend on a specific network implementation which is only one of
many ways of delivering high quality voice telephony to customers. Failure to
operate should not be reported as a fault to Telecom.
In addition to satisfactory line conditions a modem can only work properly if:
it is compatible with the modem at the other end of the call and,
74
ThinkPad® T30 Series Service and Troubleshooting Guide
the application using the modem is compatible with the application at the
other end of the call - e.g. accessing the Internet requires suitable software
in addition to a modem.
This equipment should not be used in a manner which could constitute a
nuisance to other Telecom customers.
Some parameters required for compliance with Telecom’s PTC Specifications
are dependent on the equipment (PC) associated with this modem. The
associated equipment shall be set up to operate within the following limits for
compliance with Telecom specifications:
There shall be no more than 10 call attempts to the same number within
any 30 minute period for a single manual call initiation.
The equipment shall go back on-hook for a period of not less than 30
seconds between the end of one call attempt and the beginning of the next.
Automatic calls to different numbers shall be not less than 5 seconds apart.
When used in the Auto-Answer mode, the S0 register must be set with a
value between 2 and 5. This ensures:
A person calling your modem will hear a short burst of ringing before the
modem answers. This confirms that the call has been successfully switched
through the network.
Caller identification information (which occurs between the first and
second ring cadence) is not destroyed.
This equipment does not meet Telecom’s impedance requirements.
Performance limitations may occur when used in conjunction with some parts
of the network. Telecom will accept no responsibility should difficulties arise
in such circumstances.
The code for Call Waiting disable is *52 on the Telecom New Zealand
telephone network.
For the modem with approval number PTC 211/99/020
v The grant of a Telepermit for any item of terminal equipment indicates only
that Telecom has accepted that the item complies with minimum conditions
for connection to its network. It indicates no endorsement of the product by
Telecom, nor does it provide any sort of warranty. Above all, it provides no
assurance that any item will work correctly in all respects with another item
of Telepermitted equipment of a different make or model, nor does it imply
that any product is compatible with all of Telecom’s network services.
v This equipment is not capable, under all operating conditions, of correct
operation at the higher speeds for which it is designed. Telecom will accept
no responsibility if difficulties arise in such circumstances.
Appendix E. Notices
75
v This device is equipped with pulse dialling, whereas the Telecom standard
is DTMF tone dialing. There is no guarantee that Telecom lines will always
continue to support pulse dialling.
v Use of pulse dialling, when this equipment is connected to the same line as
other equipment, may give rise to bell tinkle or noise and may also cause a
false answer condition. If such problems occur, the user should NOT
contact the Telecom Faults Service.
v This equipment shall not be set to make automatic calls to the Telecom 111
Emergency Service.
v This equipment might not provide for the effective hand-over of a call to
another device connected to the same line.
v This equipment must not be used under any circumstances that might
constitute a nuisance to other Telecom customers.
v Some parameters required for compliance with Telecom’s Telepermit
requirements are dependent on the software. In order to operate within the
limits for compliance with Telecom’s specifications, the software shall be set
to ensure that calls are answered between 3 and 30 seconds of receipt of
ringing.
v All persons using this device for recording telephone conversations shall
comply with New Zealand law. This requires that at least one party to the
conversation is to be aware that it is being recorded. In addition, the
Principles enumerated in the Privacy Act 1993 shall be complied with in
respect to the nature of the personal information collected, the purpose for
its collection, how it is to be used, and what it disclosed to any other party.
For the modem with approval number PTC 211/01/050
The grant of a Telepermit for any item of terminal equipment indicates only
that Telecom has accepted that the item complies with minimum conditions
for connection to its network. It indicates no endorsement of the product by
Telecom, nor does it provide any sort of warranty. Above all, it provides no
assurance that any item will work correctly in all respects with another item
of Telepermitted equipment of a different make or model, nor does it imply
that any product is compatible with all of Telecom’s network services.
This equipment is not capable, under all operating conditions, of correct
operation at the higher speeds for which it is designed. Telecom will accept no
responsibility should difficulties arise in such circumstances.
If a charge for local calls is unacceptable, the ’Dial’ button should not be used
for local calls. Only the seven digits of your local number should be dialled
from your modem. Do not dial the area code digit or ’0’ prefix.
This equipment should not be used under any circumstances that may
constitute a nuisance to other Telecom customers.
76
ThinkPad® T30 Series Service and Troubleshooting Guide
Some parameters required for compliance with Telecom’s Telepermit
requirements are dependent on the equipment (PC) associated with this
device. The associated equipment shall be set to operate within the following
limits for compliance with Telecom’s specifications:
Automatic re-attempts to the same number
There shall be no more than 10 call attempts to the same number within
any 30 minute period for any single manual call initiation, and
The equipment shall go on-hook for a period of not less than 30 seconds
between the end of one attempt and the beginning of the next call attempt.
Automatic calls to different numbers
Automatic calls to different numbers shall be spaced such that there is no
less than 5 seconds between the end of one call attempt and the beginning
of another.
Call answering
The associated equipment shall be set to ensure that calls are answered
between 3 and 30 seconds of receipt of ringing.
Appendix E. Notices
77
Notice for European Union countries
Hereby Ambit declares that this “J07M058” modem is in conformity with the
essential requirements and other relevant provisions of Directive 1999/5/EC.
78
ThinkPad® T30 Series Service and Troubleshooting Guide
Product notice requirements
The following notice applies to machines equipped with both a DVD and a
TV-out function:
This product incorporates copyright protection technology that is protected by
method claims of certain U.S. patents and other intellectual property rights owned by
Macrovision Corporation and other rights owners. Use of this copyright protection
technology must be authorized by Macrovision Corporation and is intended for home
and other limited viewing use only, unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is prohibited.
Trademarks
The following terms are trademarks of the IBM Corporation in the United
States or other countries or both:
IBM
HelpCenter
PS/2
ThinkLight
ThinkPad
TrackPoint
Ultrabay
UltraNav
Microsoft, Windows, and Windows NT are trademarks of Microsoft
Corporation in the United States and/or other countries.
Intel, Pentium, and SpeedStep are trademarks of Intel Corporation in the
United States and/or other countries. (For a complete list of Intel trademarks,
see www.intel.com/tradmarx.htm)
Other company, product, or service names may be the trademarks or service
marks of others.
Appendix E. Notices
79
80
ThinkPad® T30 Series Service and Troubleshooting Guide
Index
storage device, upgrading
Access ThinkPad
30
telephone, help by 35
testing with PC-Doctor 10
ThinkPad Assistant v
TrackPoint problems 17
battery
problems 23
BIOS Setup 27
carrying the computer 6
cleaning the computer 8
computer display problems
configuration
setup 27
UltraNav problems
21
17
Web, help by
34
electronic help v
error messages 11
errors without messages
14
fax, help by
35
hard disk
problems 24
upgrading 30
hibernation problems
18
IBM help
keyboard problems
16
on-board help
password problems 15
PC-Doctor for Windows 10
power switch problems 16
problems, troubleshooting 11
recovering software
28
safety instruction 39
standby problems 18
© Copyright IBM Corp. 2002
81
82
ThinkPad® T30 Series Service and Troubleshooting Guide
򔻐򗗠򙳰
Part Number: 62P9256
(1P) P/N: 62P9256

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Subject                         : 
Modify Date                     : 2002:04:01 18:02:43+09:00
Create Date                     : 2002:04:01 16:11:45Z
Page Count                      : 96
Creation Date                   : 2002:04:01 16:11:45Z
Mod Date                        : 2002:04:01 16:11:45Z
Producer                        : IBM (ID Workbench)
Author                          : IBM
Keywords                        : 
Metadata Date                   : 2002:04:01 16:11:45Z
Creator                         : IBM
Title                           : ThinkPad. T30 Series Service and Troubleshooting Guide
Description                     : 
Page Mode                       : UseOutlines
EXIF Metadata provided by EXIF.tools
FCC ID Filing: MCLU58H004

Navigation menu