HON HAI PRECISION IND WINA2 WiFi 11 b/g/n module User Manual WIN A2 030211

HON HAI Precision Ind. Co., Ltd. WiFi 11 b/g/n module WIN A2 030211

User manual

                                                                             Confidential  1                                           ʳʳʳʳʳʳʳʳʳʳʳʳʳʳWIN-A2 WIFI ModuleUser ManualRev. 0.01
                                                                             Confidential  2Review Dates Department Name Plan Results Hardware Engineering  GaoJian
                                                                             Confidential  31.  Introduction Project Name: 802.11b/g/n WIFI module. This documentation describes the product specification of the WIFI 802.11b/g/n module, it is a confidential document of FOXCONN. 1.1 Scope The device provide communications for applications operating in the globally available 2.4GHz unlicensed ISM band, which utilizing direct sequence spread spectrum and OFDM/CCK technology, the maximum data rate can reach to 65 Mbps(MCS7) for HT20. 1.2 Function ¾  Support single-band IEEE 802.11b/g and handheld device class 802.11n.¾  1x1 single stream with antenna diversity. ¾  SDIO v2.0 4bit mode interface support. ¾  Full support for power saving modes.
                                                                             Confidential  42. Product Specification 2.1 Output Center And Symbol Clock Frequency Tolerance Center frequency tolerance CH1/CH7/CH13Spec. (ppm)  +/-25 2.2 RF Specification 2.2.1 Spectrum Mask spec Mode of Operation 802.11g  Specifications 802.11 g at r 9 MHz Offset  0 dBr 802.11 g at r 11 MHz Offset  -20 dBr 802.11 g at r 20 MHz Offset  -28 dBr 802.11 g at r 30 MHz Offset  -40 dBr Mode of Operation 802.11b  Specifications 802.11b at +/-11MHz~+/-22MHz Offset  -30 dBr 802.11b at >+22MHz,<-22MHz Offset  -50 dBr Mode of Operation 802.11n-HT20  Specifications 802.11n at r9 MHz offset  0 dBr 802.11n at r11 MHz offset  -20 dBr 802.11n at r20 MHz offset  -28 dBr 802.11n at r30 MHz offset  -45 dBr
                                                                             Confidential  52.3 Electrical Specification 2.3.1 Absolute Maximum Ratings The specification indicates levels where permanent damage to the device can occur. Functional operation is not guaranteed under these conditions. Operation at absolute maximum conditions for extended can adversely affect long-term reliability of the device. Rating  Symbol  Value  Unit DC supply voltage for the device  VDD  -0.5~6  V 2.3.2 Recommended operating condition Parameter Minimum Typical   Maximum UnitDC Supply Voltage   3  3.3ʳ 3.6  [v]  2.3.3 Current consumption in active on WLAN modes
                                                                             Confidential  63. Mechanical Drawing
                                                                             Confidential  74. Regulatory Information USA-Federal Communications Commission (FCC)This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. CautionAny changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Labeling Hon Hai Precision WiFi 11b/g/n module WIN-A2 labeled as below. FCC ID: MCLWINA2 The proposed with FCC ID label format is to be placed on the module. If FCC ID is not visible when the module is installed into the system, “Contains FCC ID: MCLWINA2” shall be placed on the outside of final host system.  Caution: Exposure to Radio Frequency Radiation. To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. This device must not be co-located or operating in conjunction with any other antenna or transmitter.
                                                                             Confidential  8Canada-Industry Canada (IC)This device complies with RSS 210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of this device. The term “IC” before the equipment certification number only signifies that the Industry Canada technical specifications were met. Caution: Exposure to Radio Frequency Radiation. To comply with IC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and allpersons. This device must not be co-located or operating in conjunction with anyother antenna or transmitter.

Navigation menu