HOTA TECHNOLOGY D6PRO AC/DC Dual Channel Smart Charger User Manual D6 Pro

SHENZHEN HOTA TECHNOLOGY CO.,LTD AC/DC Dual Channel Smart Charger D6 Pro

User Manual

使用说明1、连接电源、等待开机自检完成;2、选择已连接好电池的通道;3、通过显示屏及飞梭键设置适用于您的电池的充电参数;4、开始享用。通道选择通道1平衡口通道2平衡口通道2输出口飞梭键通道1输出口5V输出AC接口DC接口 无线充电升级口功能参数净重输入电压充电功率放电功率555gUSB输出口 5V / 2.1A外部放电电流 1~15A x 2AC100~240V / DC 6.5~30VDC 325W x 2 AC 200W (自动分配)内部放电: 15W x 2(平衡口10Wx2)外部放电: 325W x 2(650W)平衡电流显示屏尺寸充电电流 放电电流 0.1~3A x 2最大1600mA x 22.8〃320×240 26万色外形尺寸 108mm×105mmx76mm存储温度 -20~60°C工作温度 0~40°C电池类型LiHv/LiPo/LiFe/Lilon/Lixx : 1~6SNiZn/Nicd/NiMH : 1~16SSmart Battery : 1~6SLead Acid(Pb) : 2~24VEnelop : 1~16S0.1~15A x 2AC/DC双通道智能充电器外观专利:201730627674.9     无线专利:201721700843.8安全注意事项:1、使用过程中确保充电器远离热源及潮湿环境,并注意通风散热;2、切勿让儿童操作充电器,请勿让充电器离开视线范围工作;3、正确设定电池充放电的参数,错误的设定可能导致意外;4、使用结束后,应尽快断开输入电源及移除电池。接入电源前请确保电源输出电压与充电器工作电压范围相符。警 告!远离火源!www.hota-exp.comUSB5V         2.1A
Internal discharge:15W × 2(balance port 10W)External discharge:325W × 2(650W) 1.  Connect the power supply, wait for self-testing to be completed;2.  Select the channel you wanna use then connect your battery to the       chosen channel;3.  Set up charging parameters applicable to your battery through the          display and speed shuttle key;4.  Enjoy.Channel SwitchBalance Port for Channel 1Balance Port for Channel 2Speed Shuttle KeyUSB Port 5VAC PortDC Port Wireless ChargingUpdate PortSpecificationsNet WeightInput VoltageCharge PowerDischarge Power555gUSB Output 5V / 2.1AExternal Discharge Current1~15A x 2AC100~240V / DC 6.5~30VDC 325W x 2AC 200W (Support power distribution)Balance CurrentScreen SizeCharge CurrentDischarge Current 0.1~3A x 21600mA x 22.8〃320×240 260000 colorsDimensions 108×105x76mmStorage Temperature-20~60°COperating Temperature0~40°CBattery TypeLiHv/LiPo/LiFe/Lilon/Lixx : 1~6SNiZn/Nicd/NiMH : 1~16SSmart Battery : 1~6SLead Acid(Pb) : 2~24VEnelop : 1~16S0.1~15A x 2AC/DC Dual Channel Smart ChargerAppearance Patent: 201730627674.9     Wireless Patent: 201721700843.8www.hota-exp.comUSB5V         2.1ABattery Port for Channel 2Battery Port for Channel 1InstructionsWARNING!FIRE HAZARD!NEVER USE CHARGER UNSUPERVISED!Batteries pose a SEVERE risk of fire if not propely handled.Read Entire operation manual before using charger.This unit may emit heat during use.Only operate this device in a cool ventilated area away from flammable objects.Failure to observe safety procedures may cause damages to property or injury.
FCC STATEMENT :   This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.  NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving an tenna.  Increase the separation between the equipment and receiver.   Connect the equipment into an outlet on a circuit different from that to which the  receiver is connected.  Consult the dealer or an experienced radio/TV technician for help.   FCC Radiation Exposure Statement: This  equipment  complies  with  FCC  radiation  exposure  limits  set  forth  for  an uncontrolled  environment.  This  equipment  should  be  installed  and  operated with minimum distance 20cm between the radiator & your body.

Navigation menu