Contents
- 1. Users Manual 1
- 2. Users Manual 2
Users Manual 2
Safety and
regulatory guide
2 Safety and regulatory guide
Please read before proceeding
THE BATTERY IS NOT FULLY CHARGED WHEN YOU TAKE THE
PRODUCT OUT OF THE BOX.
YOUR WARRANTY IS INVALIDATED IF YOU DISASSEMBLE OR
ATTEMPT TO DISASSEMBLE THE DEVICE.
Disclaimers
ANY WEATHER, STOCK, OR OTHER INFORMATION, DATA, OR
DOCUMENTATION (“ACCESSED INFORMATION”) ARE PROVIDED
“AS IS” AND WITHOUT ANY WARRANTY OR ANY TECHNICAL
SUPPORT. TO THE MAXIMUM EXTENT PERMITTED BY
APPLICABLE LAW, HTC AND ITS AFFILIATES expressly disclaim
any and all representations and warranties, arising by law or
otherwise, related to the Accessed Information, including without
limitation any express or implied representation or warranty of
merchantability, fitness for a particular purpose, non-infringement,
quality, accuracy, completeness, effectiveness, reliability, or
usefulness. Without limiting the foregoing, it is further understood
that HTC and its Affiliates are not responsible for any use of the
Accessed Information or the results arising from such use, and
that you use such information at your own risk.
Safety and regulatory guide 3
Limitation of damages
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN
NO EVENT SHALL HTC OR ITS AFFILIATES BE LIABLE TO YOU,
ANY USER, OR THIRD PARTY FOR ANY INDIRECT, SPECIAL,
CONSEQUENTIAL, INCIDENTAL OR PUNITIVE DAMAGES OF
ANY KIND, ARISING IN CONTRACT, TORT, OR OTHERWISE,
INCLUDING, BUT NOT LIMITED TO, INJURY, LOSS OF REVENUE,
LOSS OF GOODWILL, LOSS OF BUSINESS OPPORTUNITY,
LOSS OF DATA, AND/OR LOSS OF PROFITS, REGARDLESS
OF THE FORESEEABILITY THEREOF OR WHETHER HTC OR
ITS AFFILIATES HAVE BEEN ADVISED OF THE POSSIBILITY
OF SUCH DAMAGES. AND IN NO EVENT SHALL THE TOTAL
LIABILITY OF HTC OR ITS AFFILIATES EXCEED THE AMOUNT
RECEIVED FROM YOU, REGARDLESS OF THE LEGAL THEORY
UNDER WHICH THE CAUSE OF ACTION IS BROUGHT. THE
FOREGOING DOES NOT AFFECT ANY STATUTORY RIGHTS
WHICH MAY NOT BE DISCLAIMED.
Important health information and safety
precautions
When using this product, the safety precautions below must be
taken to avoid possible legal liabilities and damages.
Retain and follow all product safety and operating instructions.
Observe all warnings in the operating instructions on the product.
To reduce the risk of bodily injury, electric shock, fire, and damage
to the equipment, observe the following precautions.
Electrical safety
This product is intended for use when supplied with power from
the designated battery or power supply unit. Other usage may be
dangerous and will invalidate any approval given to this product.
Safety precautions for proper grounding installation
CAUTION: Connecting to improperly grounded equipment can
result in an electric shock to your device.
This product is equipped with a USB Cable for connecting
with desktop or notebook computer. Be sure your computer is
properly grounded (earthed) before connecting this product to
the computer. The power supply cord of a desktop or notebook
computer has an equipment-grounding conductor and a
grounding plug. The plug must be plugged into an appropriate
4 Safety and regulatory guide
outlet which is properly installed and grounded in accordance with
all local codes and ordinances.
Safety precautions for power supply unit
Use the correct external power source
A product should be operated only from the type of power
source indicated on the electrical ratings label. If you are
not sure of the type of power source required, consult your
authorized service provider or local power company. For a
product that operates from battery power or other sources,
refer to the operating instructions that are included with the
product.
Handle battery packs carefully
This product contains a Lithium-ion polymer or Lithium-ion
battery. There is a risk of fire and burns if the battery pack
is handled improperly. Do not attempt to open or service
the battery pack. Do not disassemble, crush, puncture, short
external contacts or circuits, dispose of in fire or water, or
expose a battery pack to temperatures higher than 60˚C
(140˚F).
WARNING: Danger of explosion if battery is incorrectly
replaced. To reduce risk of fire or burns, do not
disassemble, crush, puncture, short external contacts,
expose to temperature above 60° C (140° F), or
dispose of in fire or water. Recycle or dispose of used
batteries according to the local regulations or reference
guide supplied with your product.
Take extra precautions
Keep the battery or device dry and away from water or any
liquid as it may cause a short circuit.
The device should only be connected to products that bear
the USB-IF logo or have completed the USB-IF compliance
program.
If the battery leaks:
Do not allow the leaking fluid to come in contact with
skin or clothing. If already in contact, flush the aected
area immediately with clean water and seek medical
advice.
•
•
•
•
Safety and regulatory guide 5
Do not allow the leaking fluid to come in contact with
eyes. If already in contact, DO NOT rub; rinse with clean
water immediately and seek medical advice.
Take extra precautions to keep a leaking battery away
from fire as there is a danger of ignition or explosion.
Safety precautions for direct sunlight
Keep this product away from excessive moisture and extreme
temperatures. Do not leave the product inside a vehicle or in
places where the temperature may exceed 60°C (140°F), such as
on a car dashboard, window sill, or behind a glass that is exposed
to direct sunlight or strong ultraviolet light for extended periods of
time. This may damage the product, overheat the battery, or pose
a risk to the vehicle.
Prevention of hearing loss
CAUTION: Permanent hearing loss may occur if
earphones or headphones are used at high volume
for prolonged periods of time.
NOTE: For France, Earphone (listed below) for this device
have been tested to comply with the Sound Pressure
Level requirement laid down in the applicable NF EN
50332-1:2000 and/or NF EN 50332-2:2003 standards as
required by French Article L. 5232-1.
Earphone, manufactured by HTC, Model RC E160.
Safety in aircraft
Due to the possible interference caused by this product to an
aircraft’s navigation system and its communications network,
using this device’s wireless function on board an airplane is against
the law in most countries. If you want to use this device when
on board an aircraft, remember to turn off wireless function by
switching to Airplane Mode.
Environment restrictions
Do not use this product in gas stations, fuel depots, chemical
plants or where blasting operations are in progress, or in
potentially explosive atmospheres such as fuelling areas, fuel
storehouses, below deck on boats, chemical plants, fuel or
chemical transfer or storage facilities, and areas where the air
contains chemicals or particles, such as grain, dust, or metal
powders. Please be aware that sparks in such areas could cause an
explosion or fire resulting in bodily injury or even death.
•
•
•
6 Safety and regulatory guide
Explosive atmospheres
When in any area with a potentially explosive atmosphere or
where flammable materials exist, the product should be turned off
and the user should obey all signs and instructions. Sparks in such
areas could cause an explosion or fire resulting in bodily injury
or even death. Users are advised not to use the equipment at
refueling points such as service or gas stations, and are reminded
of the need to observe restrictions on the use of radio equipment
in fuel depots, chemical plants, or where blasting operations are in
progress. Areas with a potentially explosive atmosphere are often,
but not always, clearly marked. These include fueling areas, below
deck on boats, fuel or chemical transfer or storage facilities, and
areas where the air contains chemicals or particles, such as grain,
dust, or metal powders.
Road safety
Full attention must be given to driving at all times in order to
reduce the risk of an accident. Using this device while driving
(even with a hands free kit) causes distraction and can lead to
an accident. You must comply with local laws and regulations
restricting the use of wireless devices while driving.
Safety precautions for RF exposure
Avoid using your device near metal structures (for example,
the steel frame of a building).
Avoid using your device near strong electromagnetic
sources, such as microwave ovens, sound speakers, TV and
radio.
Use only original manufacturer-approved accessories, or
accessories that do not contain any metal.
Use of non-original manufacturer-approved accessories may
violate your local RF exposure guidelines and should be
avoided.
Exposure to radio frequency (RF) signals
Your device contains a radio transmitter and receiver. When it is
ON, it receives and transmits RF energy. When you communicate
with your device, the system handling your connection controls
the power level at which your device transmits.
The radiated output power is far below the international radio
frequency exposure limits. These limits are part of comprehensive
guidelines and establish permitted levels of RF energy for the
Safety and regulatory guide 7
general population. The guidelines are based on the safety
standards previously set by international standards bodies:
American National Standards Institute (ANSI) IEEE. C95.1-
1992
National Council on Radiation Protection and Measurement
(NCRP). Report 86. 1986
International Commission on Non-Ionizing Radiation
Protection (ICNIRP) 1996
Ministry of Health (Canada), Safety Code 6. The standards
include a substantial safety margin designed to assure the
safety of all persons, regardless of age and health.
Your mobile device is designed not to exceed the limits for
exposure to radio waves recommended by international guidelines.
These guidelines were developed by the independent scientific
organisation ICNIRP and include safety margins designed to
assure the protection of all persons regardless of age and health.
The guidelines use a unit of measurement known as the Specific
Absorption Rate, or SAR.
As mobile devices offer a range of functions, they can be used
in other positions, such as on the body as described in this user
guide**.
As SAR is measured utilising the device’s highest transmitting
power, the actual SAR of this device while operating is typically
below that indicated above. This is due to automatic changes to
the power level of the device to ensure it only uses the minimum
power required to communicate with the network.
**Please see the following section about body worn operation
As with other mobile radio transmitting equipment, users are
advised that for satisfactory operation of the equipment and for
the safety of personnel, it is recommended that no part of the
human body be allowed to come too close to the antenna during
operation of the equipment.
Your device has an internal antenna. Use of unauthorised or
modified antennas may impair transmission quality and damage
the device, causing loss of performance and SAR levels exceeding
the recommended limits as well as result in non-compliance with
local regulatory requirements in your country.
To assure optimal wireless performance and ensure human
exposure to RF energy is within the guidelines set forth in the
relevant standards; always use your device only in its normal-use
position. Do not touch or hold the antenna area unnecessarily
when using the wireless function. Contact with the antenna area
8 Safety and regulatory guide
may impair transmission quality and cause your device to operate
at a higher power level than needed. Avoiding contact with the
antenna area when the wireless function is IN USE optimises the
antenna performance and the battery life.
Body-worn Operation
This device was tested for typical body-worn operations. A
minimum separation distance must be maintained between the
user’s body and the handset, including the antenna:
0.5 cm to comply with the RF exposure requirements in the
U.S.
0.5 cm to comply with the RF exposure requirements in
Europe
Third-party belt-clips, holsters, and similar accessories used by this
device should not contain any metallic components. Body-worn
accessories that do not meet these requirements may not comply
with RF exposure requirements and should be avoided.
Use only the supplied or an approved antenna. Unauthorized
antennas, modifications, or attachments could impair wireless
quality, damage the device, or result in violation of regulations. Do
not use the device with a damaged antenna. If a damaged antenna
comes into contact with the skin, a minor burn may result. Please
contact your local dealer for replacement antenna.
SAR information
0.486 w/kg @ 10g (body)*
1.15 w/kg @ 1g (body)**
* NOTE: The Body SAR value of 0.486 w/kg @ 10g has been
tested with back of the device kept at 0.5 cm away from
the body.
** NOTE: The Body SAR value of 1.15 w/kg @ 1g has been tested
with back of the device kept at 0.5 cm away from the
body.
Safety and regulatory guide 9
Interference in cars
Please note that because of possible interference to electronic
equipment, some vehicle manufacturers forbid the use of mobile
device in their vehicles unless a handsfree kit with an external
antenna is included in the installation.
Interference with medical equipment functions
This product may cause medical equipment to malfunction. The
use of this device is forbidden in most hospitals and medical clinics.
If you use any other personal medical device, consult the
manufacturer of your device to determine if they are adequately
shielded from external RF energy. Your physician may be able to
assist you in obtaining this information.
Turn your device OFF in health care facilities when any regulations
posted in these areas instruct you to do so. Hospitals or health
care facilities may be using equipment that could be sensitive to
external RF energy.
Hearing aids
Some digital wireless devices may interfere with some hearing
aids. In the event of such interference, you may want to consult
your service provider, or call the customer service line to discuss
alternatives.
Nonionizing radiation
Your device has an internal antenna. This product should be
operated in its normal-use position to ensure the radiative
performance and safety of the interference. As with other
mobile radio transmitting equipment, users are advised that for
satisfactory operation of the equipment and for the safety of
personnel, it is recommended that no part of the human body be
allowed to come too close to the antenna during operation of the
equipment.
Use only the supplied integral antenna. Use of unauthorized or
modified antennas may impair transmission quality and damage
the device, causing loss of performance and SAR levels exceeding
the recommended limits as well as result in non-compliance with
local regulatory requirements in your country.
10 Safety and regulatory guide
To assure optimal device
performance and ensure human
exposure to RF energy is within
the guidelines set forth in the
relevant standards, always use
your device only in its normal-use
position. Contact with the antenna
area may impair transmission
quality and cause your device to
operate at a higher power level
than needed. Avoiding contact
with the antenna area when the
device is IN USE optimizes the
antenna performance and the
battery life.
Antenna location
Electrical safety
Accessories
Use only approved accessories.
Do not connect with incompatible products or accessories.
Take care not to touch or allow metal objects, such as coins or
key rings, to contact or short-circuit the battery terminals.
Connection to a car
Seek professional advice when connecting a device interface to
the vehicle electrical system.
Faulty and damaged products
Do not attempt to disassemble the device or its accessory.
Only qualified personnel must service or repair the device or
its accessory.
•
•
•
•
•
Safety and regulatory guide 11
General precautions
You alone are responsible for how you use your device and any
consequences of its use. You must always switch off your device
wherever the use of a wireless device is prohibited. Use of your
device is subject to safety measures designed to protect users and
their environment.
Avoid applying excessive pressure to the device
Do not apply excessive pressure on the screen and the device to
prevent damaging them and remove the device from your pants’
pocket before sitting down. It is also recommended that you
store the device in a protective case and only use your finger
when interacting with the touch screen. Cracked display screens
due to improper handling are not covered by the warranty.
Device getting warm after prolonged use
When using your device for prolonged periods of time, such
as when you’re charging the battery or browsing the Web,
the device may become warm. In most cases, this condition is
normal and therefore should not be interpreted as a problem
with the device.
Heed service markings
Except as explained elsewhere in the Operating or Service
documentation, do not service any product yourself. Service
needed on components inside the device should be done by an
authorized service technician or provider.
Protect your device
Always treat your device and its accessories with care and
keep them in a clean and dust-free place.
Do not expose your device or its accessories to open flames
or lit tobacco products.
Do not expose your device or its accessories to liquid,
moisture or high humidity.
Do not drop, throw or try to bend your device or its
accessories.
Do not use harsh chemicals, cleaning solvents, or aerosols to
clean the device or its accessories.
Do not paint your device or its accessories.
Do not attempt to disassemble your device or its accessories,
only authorised personnel must do so.
Do not expose your device or its accessories to extreme
temperatures, minimum -20 and maximum 50 degrees Celsius.
Please check local regulations for disposal of electronic
products.
•
•
•
•
•
•
•
•
•
12 Safety and regulatory guide
Do not carry your device in your back pocket as it could break
when you sit down.
Damage requiring service
Unplug the product from the electrical outlet and refer servicing
to an authorized service technician or provider under the
following conditions:
Liquid has been spilled or an object has fallen into the product.
The product has been exposed to rain or water.
The product has been dropped or damaged.
There are noticeable signs of overheating.
The product does not operate normally when you follow the
operating instructions.
Avoid hot areas
The product should be placed away from heat sources such as
radiators, heat registers, stoves, or other products (including
amplifiers) that produce heat.
Avoid wet areas
Never use the product in rain, or near washbasins or other wet
locations. If your product gets wet, do not try to dry the product
with the use of an oven or dryer, as this may damage your
product.
Avoid using your device after a dramatic change in
temperature
When you move your device between environments with very
different temperature and/or humidity ranges, condensation
may form on or within the device. To avoid damaging the device,
allow sufficient time for the moisture to evaporate before using
the device.
NOTICE: When taking the device from low-temperature
conditions into a warmer environment or from high-
temperature conditions into a cooler environment,
allow the device to acclimate to room temperature
before turning on power.
Avoid pushing objects into product
Never push objects of any kind into cabinet slots or other
openings in the product. Slots and openings are provided for
ventilation. These openings must not be blocked or covered.
Air bags
Do not place a device in the area over an air bag or in the air
bag deployment area. Store the device safely before driving
your vehicle.
•
•
•
•
•
•
Safety and regulatory guide 13
Mounting accessories
Do not use the product on an unstable table, cart, stand,
tripod, or bracket. Any mounting of the product should follow
the manufacturer’s instructions, and should use a mounting
accessory recommended by the manufacturer.
Avoid unstable mounting
Do not place the product with an unstable base.
Use product with approved equipment
This product should be used only with personal computers and
options identified as suitable for use with your equipment.
Adjust the volume
Turn down the volume before using headphones or other audio
devices.
Cleaning
Unplug the product from the wall outlet before cleaning. Do not
use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning, but NEVER use water to clean the LCD screen.
Small children
Do not leave your device and its accessories within the reach
of small children or allow them to play with it. They could hurt
themselves or others, or could accidentally damage the device.
Your device contains small parts with sharp edges that may
cause an injury or which could become detached and create a
choking hazard.
Repetitive motion injuries
To minimise the risk of RSI, when Texting or playing games with
your device:
Do not grip the device too tightly
Press the buttons lightly
Make use of the special features in the handset which minimise
the number of buttons which have to be pressed, such as
message templates and predictive text.
Take lots of breaks to stretch and relax.
Operating machinery
Full attention must be given to operating the machinery in order
to reduce the risk of an accident.
Electrostatic discharge (ESD)
Do not touch the SIM card’s metal connectors.
Loud noise
This device is capable of producing loud noises which may
damage your hearing.
•
•
•
•
14 Safety and regulatory guide
Regulatory agency identifications
For regulatory identification purposes, your product is assigned a
model number of PG41400.
To ensure continued reliable and safe operation of your device, use
only the accessories listed below with your PG41400.
Operating temperature range: 32°F to 104°F (0°C to 40°C)
NOTE: This product is intended for use with a certified Class 2
Limited Power Source, rated 9 Volts DC, maximum 1.67
Amp power supply unit.
European Union notice
Products with CE marking comply with the R&TTE Directive
(99/5/EC), the EMC Directive (2004/108/EC), and the Low
Voltage Directive (2006/95/EC) issued by the Commission of the
European Community.
Compliance with these directives implies conformity to the
following European Norms (in parentheses are the equivalent
international standards).
EN 301 489-1
EN 301 489-3
EN 301 489-17
EN 300 328
EN 300 440-1
EN 300 440-2
EN 60950-1
EN 62311
EN 62209-2
EN 50332-1
This equipment may be operated in:
AT BE BG CH CY CZ DE DK
EE ES FI FR GB GR HU IE
IT IS LI LT LU LV MT NL
NO PL PT RO SE SI SK TR
•
•
•
•
•
•
•
•
•
•
Safety and regulatory guide 15
Federal Communications Commission notice
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or TV reception, which can
be determined by turning the equipment on and off, the user is
encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent
from that to which the receiver is connected.
Consult the dealer or an experienced radio or television
technician for help.
Modifications
The FCC requires the user to be notified that any changes or
modifications made to the device that are not expressly approved
by HTC Corporation may void the user’s authority to operate the
equipment.
FCC RF Radiation Exposure Statement
This Transmitter has been demonstrated co-location
compliance requirements with Bluetooth and WLAN.
This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
This equipment complies with FCC RF radiation exposure
limits set forth for an uncontrolled environment.
16 Safety and regulatory guide
Telecommunications & Internet Association (TIA)
safety information
Pacemakers
The Health Industry Manufacturers Association recommends that
a minimum separation of 15 cm (6 inches) be maintained between
a handheld wireless device and a pacemaker to avoid potential
interference with the pacemaker. These recommendations
are consistent with the independent research by and
recommendations of Wireless Technology Research.
Persons with pacemakers:
Should ALWAYS keep the device more than
15 cm (6 inches)
from their pacemaker when the device is turned ON.
Should not carry the device in a breast pocket.
Should use the ear opposite the pacemaker to minimize
the potential for interference. If you have any reason to
suspect that interference is taking place, turn the device OFF
immediately.
Hearing aids
Some digital wireless devices may interfere with some hearing
aids. In the event of such interference, you may want to consult
your service provider, or call the customer service line to discuss
alternatives.
WEEE notice
The Directive on Waste Electrical and Electronic Equipment
(WEEE), which entered into force as European law on 13th
February 2003, resulted in a major change in the treatment of
electrical equipment at end-of-life.
The purpose of this Directive is, as a first priority, the prevention of
WEEE, and in addition, to promote the reuse, recycling and other
forms of recovery of such wastes so as to reduce disposal.
Safety and regulatory guide 17
The WEEE logo (shown at the left) on the
product or on its box indicates that this product
must not be disposed of or dumped with
your other household waste. You are liable
to dispose of all your electronic or electrical
waste equipment by relocating over to the
specified collection point for recycling of such
hazardous waste. Isolated collection and proper
recovery of your electronic and electrical waste
equipment at the time of disposal will allow us
to help conserving natural resources. Moreover,
proper recycling of the electronic and electrical
waste equipment will ensure safety of human
health and environment. For more information
about electronic and electrical waste equipment
disposal, recovery, and collection points, please
contact your local city center, household
waste disposal service, shop from where you
purchased the equipment, or manufacturer of
the equipment.
RoHS compliance
This product is in compliance with Directive 2002/95/EC of the
European Parliament and of the Council of 27 January 2003,
on the restriction of the use of certain hazardous substances in
electrical and electronic equipment (RoHS) and its amendments.
18 Safety and regulatory guide
RF Exposure Information (SAR)
This device meets the government’s requirements for exposure to
radio waves.
This device is designed and manufactured not to exceed the
emission limits for exposure to radio frequency (RF) energy set by
the Federal Communications Commission of the U.S. Government.
The exposure standard employs a unit of measurement known
as the Specific Absorption Rate, or SAR. The SAR limit set
by the FCC is 1.6W/kg. Tests for SAR are conducted using
standard operating positions accepted by the FCC with the EUT
transmitting at the specified power level in different channels.
The highest SAR value for the device as reported to the FCC is 1.15
W/kg when placed next to the body.
The FCC has granted an Equipment Authorization for this device
with all reported SAR levels evaluated as in compliance with the
FCC RF exposure guidelines. SAR information on this device is
on file with the FCC and can be found under the Display Grant
section of www.fcc.gov/oet/ea/fccid after searching on FCC ID:
NM8PG41400.
This device is compliance with SAR for general population
/uncontrolled exposure limits in ANSI/IEEE C95.1-1999 and had
been tested in accordance with the measurement methods and
procedures specified in OET Bulletin 65 Supplement C.
Safety and regulatory guide 19
IC Warning Statement
This device complies with Industry Canada licence-exempt RSS
standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference
that may cause undesired operation of the device.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.
This Category II radiocommunication device complies with
Industry Canada Standard RSS-310.
Ce dispositif de radiocommunication de catégorie II respecte la
norme CNR-310 d’Industrie Canada.
IMPORTANT NOTE:
IC Radiation Exposure Statement
This EUT is compliance with SAR for general population/
uncontrolled exposure limits in IC RSS-102 and had been tested
in accordance with the measurement methods and procedures
specified in IEEE 1528. This equipment should be installed and
operated with minimum distance 1.5 cm between the radiator &
your body.
This device and its antenna(s) must not be co-located or operating
in conjunction with any other antenna or transmitter.
The County Code Selection feature is disabled for products
marketed in the US/Canada.
For product available in the USA/ Canada markets, only channel
1~11 can be operated. Selection of other channels is not possible.
23, Xinghua Rd.,
Taoyuan 330, Taiwan
宏達國際電子股份有限公司
HTC Corporation
DECLARATION OF CONFORMITY
Intended for use in EU
For the following equipment:
Tablet PC
(Product Description)
HTC Flyer
(Product Marketing Name)
PG41400
(Product Name)
HTC Corporation
(Manufacturer Name)
No.23, Xinghua Rd., Taoyuan City, Taoyuan County 330, Taiwan.
(Manufacturer Address)
is herewith confirmed to comply with the essential requirements of Article 3 of the R&TTE 1999/5/EC
Directive, if used for its intended use and that the following standards has been applied:
1.
Health (Article 3.1.a of the R&TTE Directive):
Applied standard(s): EN62311: 2008/ EN 62209-2:2010
2. Safety (Article 3.1.a of the R&TTE Directive)
Applied standard(s): EN60950-1:2006+A11:2009, EN50332-1:2000,
3. Electromagnetic compatibility (Article 3.1.b of the R&TTE Directive)
Applied standard(s): EN 301 489-1 V1.8.1/-3 V1.4.1/-17 V2.1.1
4. Efficient use of the radio frequency spectrum (Article 3.2 of the R&TTE Directive)
Applied standard(s): EN 300 328 V1.7.1, EN 300 440-1 V1.6.1/-2 V1.4.1
Person responsible for making this declaration:
Philip Blair
(Name and signature)
Product Director
(Position / Title)
Taiwan 2011/4/18
(Place) (Date)
91H0xxxx-xxM Rev.A
htc.com