HUBSAN INTELLIGENT 507DRX X4 STAR FPV User Manual 1 of 2

Download:
Mirror Download [FCC.gov]
Document ID	3263869
Application ID	lHKS8EVbv3NnSk28oqrgWg==
Document Description	User Manual (1 of 2)
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	406.73kB (5084163 bits)
Date Submitted	2017-01-18 00:00:00
Date Available	2017-01-18 00:00:00
Creation Date	2017-01-10 14:35:21
Producing Software	Adobe PDF library 10.01
Document Lastmod	2017-01-16 09:25:07
Document Title	PP1000715_01-说明书-H502D中文版说明书
Document Creator	Adobe Illustrator CS6 (Windows)

®
14+
READ THE INSTRUCTION MANUAL CAREFULLY BEFORE USE
X4 STAR FPV
H507D USER MANUAL
ARM/DISARM MOTORS, SEE PAGE 12
RTH FUNCTION, SEE PAGE 15
FOLLOW ME FUNCTION, SEE PAGE 16
TRANSMITTER CALIBRATION, SEE PAGE 22
01
©2016
Hubsan
哈博森科技 版权所有
COMPASS CALIBRATION
Compass Calibration is required after the binding as instructed on the transmitter.
1 ) Horizontally rotate the X4 in a clockwise direction when the LCD screen shows “Calib compass 1”
2 ) Put the X4 nose down and vertically rotate it in a clockwise direction when the LCD screen shows “Calib
compass 2”
3 ) Calibration is completed when the 4 LED indicators remain solid.
Horizontally rotate the X4 in a clockwise direction
Put the X4 nose down and vertically rotate it
when the LCD screen shows “Calib compass 1”
in a clockwise direction when the LCD screen shows “Calib compass 2”
START
COMPLETE
When the quadcopter yaws during flight, please calibrate the compass manually as insturcted below:
1) Pull the left stick to the left side, and move the right stick from left to right quickly
and repeat until the transmitter displays “Calib compass1”, and the 4 LED indicators blink circularly.
2) Horizontally rotate the X4 in a clockwise direction until the LCD screen shows “Calib compass 2”,
and the 4 LED indicators blink alternately.
3) Put the X4 nose down and vertically rotate it in a clockwise direction until the “Calib compass 2”
disappears.
4) Calibration is completed when the 4 LED indicators remain solid.
Pull the left stick to the left side
Move the right stick left to right
quickly, the LCD screen displays “Calib compass 1”
START
Horizontally rotate the X4 in a clockwise direction
Put the X4 nose down and vertically rotate it
until the LCD screen shows “Calib compass 2”
lockwise direction until the “Calib compass 2” disappears.
Calibration completed
02
©2016
Hubsan
哈博森科技 版权所有
Do not calibrate the compass in a strong magnetic field
Do not carry ferromagnetic materials with you while calibrating the compass,
such as keys, cell phones, etc.
Horizontal Calibration
Horizontal Calibration is required when the quadcopter drifts during flight.
Calibration Procedures:
Push the left stick to the most right side, and move the right stick from left to right quickly
until the 4 LED indicators blink slowly.
Calibration is completed when the 4 LED indicators remain solid.
CAUTION:
For safety, the quadcopter is default set to CAN NOT FLY WHEN NO GPS. If you prefer to
fly when GPS is not available, please reset the value as instructed below before using.
Pull the throttle stick to the lowest position and press the Elevator stick for 1.5 seconds to
enter into the MAIN MENU interface. Push the Elevator stick up/down to select “Fly When
no GPS”, push the stick right to enter into the “ Fly When no GPS” interface, select “YES”.
The Default Setting is “NO”.
Select “Exit” to exit.
0:08:49 M2
MAIN MENU
Set Reverse
Set Sensitivity
5.8G Frequency
Set Manual
Fly When no GPS
Show Version
Exit
03
©2016
Hubsan
哈博森科技 版权所有
0:08:49
M2
Fly When NO GPS
Exit
YES
Hubsan X4 User Manual
V1.0
2016.05
IMPORTANT SAFETY NOTES
OPERATION: Be extremely careful and responsible when using the Quad.
Small electronic components can be damaged by crashes or by dropping
into water. To avoid any injuries, do not use the quad with broken or
damaged components.
Maintenance: Do not try to fix the quad by yourself, please contact Hubsan
distributors authorized by Hubsan for customer services.
For more information, please visit official website at www.hubsan.com
Battery: Do not put the battery in high temperature area above 60 degrees.
Using a Hubsan dedicated charger for recharging.
Keep the batteries away from children.
Keep the batteries dry.
·Do not fly the quad in crowded places, always be aware of the safety of yourself and others.
·Do not fly in bad weather.
·Never try to catch the quad while it is in flight.
·This quad is intended for experienced pilots age 14+.
·Take off the battery if it is not in use, to avoid accidentally injuries.
·Keep your body away from propellers after power on, High speed propellers are very dangerous
Read the Disclaimer first before use.
※SYMBOL EXPLANATION
No operating
Important Notice
Instruction
Explanation, reference
USAGE ADVICE
Hubsan provides you with two files for your quad:
1.《Disclaimer》
2.《Quick Start Guide》
Watch the tutorial video and read the Disclaimer first,.
For detail information, please download User Manual at www.hubsan.com.
04
©2016
Hubsan
哈博森科技 版权所有
or
Safety Advisory Notice for Lithium-Polymer (LIPO) Batteries
LiPo batteries are different from conventional batteries in that their chemical contents
are encased in a relatively lightweight foil packaging. This has the advantage of
significantly reducing their weight but it does make them more susceptible to damage
if roughly or inappropriately handled. As with all batteries, there is a risk of fire or
explosion if safety practices are ignored:
● If you do not plan to fly the quad for a long time, store the battery approximately 50%
charged to maintain battery performance and battery life.
● Please use Hubsan chargers for battery charging.
● Discharging the battery within 5C current , do not over-discharging.
● Do not charge on carpet to avoid fire.
● Batteried need to be recharged if not in use for over 3 months.
1.Charge and store LiPo batteries in a location where a battery fire or explosion
(including smoke hazard) will not endanger life or property.
2.Keep LiPo batteries away from children and animals.
3.Never charge the LiPo battery that has ballooned or swelled.
4.Never charge the LiPo battery that has been punctured or damaged.
5.After a crash, inspect the battery pack for signs of damage. Discard in accordance
with your country’s recycling laws.
6.Never charge the LiPo battery in a moving vehicle.
7.Never overcharge the LiPo battery.
8.Never leave the LiPo battery unattended during recharging
9.Do not charge LiPo batteries near flammable materials or liquids.
10.Ensure that charging leads are connected correctly. Reverse polarity charging can
lead to battery damage or a fire or explosion.
11.Have a suitable fire extinguisher (electrical type) OR a large bucket of dry sand near
the charging area . Do not try to extinguish electrical (LiPo) battery fires with water.
12.Reduce risks from fire/explosion by storing and charging LiPo batteries inside a
suitable container.
13.Protect your LiPo battery from accidental damage during storage and
transportation. (Do not put battery packs in pockets or bags where they can short
circuit or can come into contact with sharp or metallic objects.).
14.If your LiPo battery is subjected to a shock (such as a crash), place it in a metal
container and observe for signs of swelling or heating for at least 30 minutes.
15.Do not attempt to disassemble or modify or repair the LiPo battery.
05
©2016
Hubsan
哈博森科技 版权所有
Contents
Compass Calibration
0 2
Safety Notes
0 4
6 Advanced Performance Setup
6.1GPS POSITIONING/ hOME POINT SETTING
1 4
Information
6.2 RTH Mode
1 5
SYMBOL EXPLANATION
0 4
6.3 Headless Mode
1 6
USAGE ADVICE
0 4
6.4 Follow Me Mode
1 6
0 6
6.5 Failsafe Mode
1 6
Contents
Introduction
1 Item List
0 7
2 LED Indicator Status
0 8
3 Quadcopter Battery
Transmitter
1 8
7.1 Key Function
1 9
7.2 Install TX Battery
1 9
3.1 Introduction
0 9
7.3 Reversing channel setup
1 9
3.2 Install the Battery
0 9
7.4 SENSITIVITY SETUP
2 0
3.3 Charging
0 9
7.5 manual MODE SETUP
2 1
8 Transmitter Calibration
2 2
9 Frequency selectable 5.8Ghz
2 2
Exploded View
2 3
H507D Spare Part List
2 5
Troubleshooting
2 6
Propeller
Start to Fly
5.1 Flight Environment
1 1
5.2 Safety check before flight 1 1
5.3 Binding
1 1
5.4 Arm/Disarm motors
1 2
5.5 Basic Flight
1 2
5.6 Photo/Video
1 4
06
©2016
Hubsan
哈博森科技 版权所有
INTRODUCTION
Thank you for buying the HUBSAN product. It is designed as an easy-to-use, multi-functional RC model,
capable of hovering and acrobatic flight maneuvers. Please read the manual carefully and follow all the
instructions. Be sure to keep the manual for future reference.
Flight Weight: 164.5g (including prop protections & Battery)
FPV：First Person View，this feature enables you to experience every live moment of the flight
from the drone's point of view.
1. ITEMS INCLUDED IN THE BOX
Check all the items in the box before using.
S/N
Part Name
Quad copter
Photos
Q'ty
1PC
FCC ID:2AEXY507DRX
Propellers
8PCS
Transmitter
1PC
FCC ID:2AEXY901ATX
07
7.6V Li-Po battery
USB Charger
©2016 Hubsan
哈博森科技 版权所有
1PC
1PC
Remarks
Equipped with smart flight
controller,GPS and compass
Propeller A 4pcs, Propeller
B 4pcs
FPV Transmitter (powered by
4 X AA battery -Not included)
For quad copter
For Li-Po battery charging
2. QUAD COPTER MOTOR LED INDICATOR
Indicator Status:
Front LED is blue; Back LED is red.
1. Power on: 4 LED indicators blink simultaneously every 1.5 seconds.
2. Compass Calibration:
1). Horizontal calibration: 4 LED indicators blink circularly.
2). Vertical calibration: 4 LED indicators blink alternately.
3. Quadcopter Calibration: 4 LED indicators blink slowly.
4. GPS Flight: 4 LED indicators remain solid.
5. GPS Return : 2 front LED indicators remain solid, and 2 back LED indicators blink slowly.
6. Low Voltage: 2 front LED indicators remain solid, and 2 back LED indicators blink quickly.
7. Signal Lost: 2 front LED indicators blink slowly, 2 back LED indicators remain solid.
8. Photo: 2 front LED indicators remain lighted, 2 back LED indicators blink once.
9. Video: 2 front LED indicators remain lighted, 2 back LED indicators blink alternately.
10. LED indicators can be turned off by long pressing the LED SW on transmitter.
3. QUAD COPTER BATTERY
3.1 INTRODUCTION
The quad copter battery is a rechargeable Li-Po battery with 450mAh capacity and 7.6V voltage.
The battery should only be charged with the HUBSAN charger to avoid overcharge.
Please make sure the battery is fully charged before use it for the first time.
3.2 INSTALL THE BATTERY
Push the battery into the battery compartment correctly
and connect the battery plugs with the correct polarity.
Close the battery compartment cover.
3.3 CHARGING
Connect the battery to the USB charger, then connect the
USB charger to the USB device, such as a computer or a
mobile power charger.
It takes around 110 minutes to have the battery fully
charged. The USB LED indicator blink slowly in red when
charging and will remain solid when the battery is complete
charged. Please unplug the charger and battery when the
charging is completed.
Please fully charge the batteries to avoid loss of control due to low voltage.
Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the local regulations.
08
©2016
Hubsan
哈博森科技 版权所有
4. PROPELLERS
The quad copter uses the 5.3-inch propellers which are marked by A and B.
Propellers are consumables, please replace with new ones if there is any damage.
Attach the propellers to the corresponding motors that
are marked A and B,tighten the propellers and keep the
motors deadlocked with the screw-driver.
Black screw
Silver screw
Tighten the A propeller with black screw;
Tighten the B propeller with sliver screw.
“I” Mark
“D”Gap

Match the “I” mark on propellers to the “D” gap on
motor shafts when assembling, as figure 1 shown.
● Make sure that the A and B propellers are installed correctly. The X4 will not fly if
propellers are improperly installed.
● Keep the moving propellers away from your body as well as other people and any obstacles.
09
©2016
Hubsan
哈博森科技 版权所有
5. START TO FLY
In case of any injuries caused by improper operations, it is advised that beginners learn to
operare the quad under the guidance of professional.It is very improtant to choose the
right flight environment.
5.1 FLIGHT ENVIRONMENT
(1) The flying area should be open and is without tall buildings, otherwise the GPS
may not work.
(2) Do not fly in bad weather like windy, snowy, rainy or foggy days.
(3)Stay away from obstacles, crowds, power cables, trees and water etc.
(4) Do not fly near the radio towers or airports.
(5) The quad will not work in the Antarctic Circle or the Arctic Circle.
(6) Obey the local laws and regulations, do not fly in restricted areas.
(7) Only fly in good weather conditions and air temperatures between 0-40℃
(not including rain, wind or other extreme weather.)
High Tension Line
Airport
Interference
Rain
5.2 SAFETY CHECK BEFORE FLIGHT
(1) Make sure the batteries are fully charged. (Quad,transmitter or smart device)
(2) Make sure propellers are installed properly.
(3) Insert Micro-SD card for pictures and videos.
(4) Check if motors work well after binding.
5.3 BINDING
The binding is completed in the factory.
For re-binding, press Photo button and power on the transmitter simultaneously until “Bind to
Plane” is displayed, then power on the drone and place it very close to the transmitter, the binding
process will be completed after one “ beep” sound.
If the binding failed, please power off the drone and repeat the above steps.
10
©2016
Hubsan
哈博森科技 版权所有
5.4 ARM/ DISARM THE MOTORS
Arm the motors
Method : Pull both sticks to the lower outer corner as shown
on the picture to arm the motors. Release both sticks
after the motors are armed.
If the motors can not be armed after binding, please make sure:
1. Compass calibration is completed
2. The value of Fly When No GPS is “YES”
3. GPS switch and RTH switch is OFF.
Disarm the motors
Method : Pull both sticks to the lower outer corner again to arm the motors, and release both sticks
after the motors are disarmed.
Do not stop the motors during the flight to avoid crashing.
Push the sticks lightly. Release the sticks after the motors are armed or disarmed.
5.5 Basic Flight
The operations of the controller are based on Mode 2.
The left stick controls the altitude and rudder of quadcopter, and the right stick controls
its forward, backward, left and right flight.
Transmitter (Mode 2)
X4
UP
Remarks
The throttle stick controls the ascent and
descent .
Push up the stick and the X4 will ascend.
Pull down the stick and the X4 will descend.
When the stick is in the center, the X4 will hover
and hold its alititude automatically .
Down
Right rotation
Move the throttle stick above the center position
to take off. (Move the stick gradually to prevent
the X4 from ascending too quickly.)
The Rudder stick controls the rotate direction
Push the stick to the left and the X4 will rotate
counter-clockwise
Push the stick to the right and the X4 will rotate
clockwise.
When the stick is in the center,the X4 will keep
the current direction and not rotate.
Pushing harder will cause the X4 to rotate
faster in the corresponding directions.
Left rotation
11
©2016
Hubsan
哈博森科技 版权所有
Forward
The Elevator stick moves the X4 forward and
backward.
Push the stick up the and the X4 will fly
forward.
Pull the stick down and the X4 will fly
backward.
When the stick is in the center, the X4 will hold
its position.
The angle of stick movement corresponds to
the angle of tilt and flight speed.
Backward
The Aileron stick controls left and right flight.
Push the stick to the left and the X4 will fly to
the left.
Push the stick to the right and the X4 will fly to
the right.
The X4 will keep the current status when the
stick is in the center.
Left
Right
The angle of stick movement corresponds to
the angle of tilt and flight speed.
The GPS Switch controls the position-hold
function.
In position 1 (up), the GPS function works.
position 1 (upward)
GPS Switch
Photo Button
position 2 (downward)
In position 2 (down), the GPS function is
inactive.
RTH Switch
Video Button
The RTH Switch controls the automatic return
home function.
In position 1 (up), the RTH function works.
In position 2 (down), the RTH function is
inactive.
Important Note: The GPS and RTH functions are only available
outdoors.Please make sure the two switches keep downward when
indoors.
For the Photo/Video function, always
power off the quadcopter and the
transmitter when inserting or removing
the SD card
12
©2016
SD
Hubsan
哈博森科技 版权所有
5.6 PHOTO/VIDEO
PHOTO
VIDEO
Insert the SD card into quadcopter before using Photo/Video function.
Press the Photo button once to take photo.
Press the Video button once to take video and press again to save the video.
Stop recording before the SD card is removed.
6. ADVANCED PERFORMANCE SETUP
6.1 GPS POSITIONING/ HOME POINT SETTING
1.) GPS Positioning works ONLY when the GPS signal has no less than 6 satellites.
00:23:59
X4
7.3V
R 0
P 0
H 247
0.3m/s
1.5m
0m
00:23:59
X4
7.3V
R 0
P 0
H 247
0.3m/s
1.5m
0m
X4 GPS 6
GPS 6
N22.7914931
E:114.0479740
N:22.7914650
E:114.0479983
X4 GPS 6
N22.7914931
E:114.0479740
N:22.7914650
E:114.0479983
Altitude
GPS 6
Altitude
Push up the GPS switch to activate the GPS positioning.
Pull down the GPS switch to exit the GPS positioning (only altitude hold will be active).
13
©2016
Hubsan
哈博森科技 版权所有
2.) Home Point is recorded when armed the motors with no less than 6 GPS satellites.
3.) You should be in an open place to search for the GPS satellites, it’ll take 3 mins to finish the
searching, and the GPS signal strength depends on the flying environment.
6.2 RTH MODE (RETURN TO HOME)
ENTER INTO RTH MODE
Push the GPS Switch and the RTH Switch up, and the quad copter will enter into RTH mode.
The flight control system will control the quad copter to fly back to the home point and land
automatically.
! The RTH MODE only works when the GPS mode is activated with no less than 6 satellites.
The Home Point is recorded when armed the motors with no less than 6 GPS satellites.
EXIT RTH MODE
Pull down the RTH Switch, the X4 will exit the RTH Mode.
14
©2016
Hubsan
哈博森科技 版权所有
6.3 HEADLESS MODE
Headless mode means the X4
will default any directions
(corresponding to the directions
of transmitter sticks) as the up ahead
when the mode is activated.
MODE 2
MODE 1
Short press down the throttle stick to switch on/ off headless mode.
Short press down the throttle stick to enter into Headless Mode, indicated by two "beep" sounds
and the “HEADLESS ON” displays on the LCD screen.
Short press down the throttle stick again to exit Headless Mode, indicated by one "beep" sound
and the ”HEADLESS OFF” displays on the LCD screen.
6.4 FOLLOW ME MODE
Follow Me Mode means the
drone follows the transmitter
automatically as it has
built-in GPS system.
MODE 2
MODE 1
Short press down the elevator stick to switch on/ off follow me mode.
Short press down the elevator stick to enter into the follow me Mode, indicated by two "beep" sounds,
the “ FOLLOW ON” displays on the LCD screen, the drone will turn and face to the transmitter.
Important Notice: When the quadcopter is in follow me mode, press any sticks or trims may exit
the mode except the throttle stick.
Short press down the elevator stick again to exit follow me Mode, indicated by one "beep" sound a
nd the “ FOLLOW OFF” displays on the LCD .
! The follow me mode only works when the GPS (both on transmitter and on drone) has
no less than 6 satellites.
6.5 FAILSAFE MODE
The quad copter will enter into failsafe mode when the connection is lost from the transmitter, or
when the power is low. The flight control system will control the quad copter to return to the
HOME POINT and land automatically. The failsafe mode helps to avoid injuries or damages.
15
©2016
Hubsan
哈博森科技 版权所有

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1-701
Modify Date                     : 2017:01:16 09:25:07+08:00
Create Date                     : 2017:01:10 14:35:21+08:00
Metadata Date                   : 2017:01:16 09:25:07+08:00
Creator Tool                    : Adobe Illustrator CS6 (Windows)
Format                          : application/pdf
Title                           : PP1000715_01-说明书-H502D中文版说明书
Document ID                     : uuid:816425ff-ec45-44d2-bdd4-8cc6f99d0aa0
Instance ID                     : uuid:0b137bf6-587c-4a93-bb56-cc21842f6dfb
Producer                        : Adobe PDF library 10.01
Has XFA                         : No
Page Count                      : 15
Creator                         : Adobe Illustrator CS6 (Windows)

EXIF Metadata provided by EXIF.tools