Hager I 1303 DBL_ACT_SPRING_HINGE_REVB DBL ACT Spring Hinge Installation Instructions Revb

User Manual: Hager 1303 DBL ACT Spring Hinge Installation Instructions Installation Instructions

Open the PDF directly: View PDF PDF.
Page Count: 1

DownloadHager I-1303 DBL_ACT_SPRING_HINGE_REVB 1303 DBL ACT Spring Hinge Installation Instructions Revb
Open PDF In BrowserView PDF
TOP VIEW

REVISIONS

(FIG. 1)

T
RO ENS
D IO

TENSION LUG ON BOTTOM
N
IO
NS
TE O D
R

N

TENSION LUG ON TOP

DOOR

DOOR

TO INCREASE TENSION, INSERT TENSION ROD AND ROTATE AS SHOWN

JAMB
FLANGE

TENSION LUG WITH
ADJUSTMENT HOLES

DO

OR

JAMB
FLANGE

OR

DO

JAMB

JAMB
DOORS ROTATING AROUND JAMB FLANGE

TENSION PIN
DOOR
FLANGE

DOOR
FLANGE

DO

OR

JAMB

DETAIL A

TENSION LUG WITH
ADJUSTMENT HOLES

TENSION PIN

R

O
DO

JAMB

DETAIL B

DOORS ROTATING AROUND DOOR FLANGE

3” [76MM]

B

A
2” TO 3”
[50MM-76MM]

3/16” [5MM] MIN.
1/4” [6MM] TYP.

1/4” [6MM] MORTISED
5/16” [8MM] NON-MORTISED

B

B

DATE

A

FOR COMPUTER

01/27/06

B

ADDED CLEARANCES

02/28/06

APPROVED

1. TO PROPERLY MOUNT SPRING HINGES, IT IS NECESSARY TO RELEASE THE TENSION ON THE SPRINGS. INSERT
THE TENSION ROD INTO ONE OF THE ADJUSTMENT HOLES ON THE TENSION LUG AND TURN IT SO THAT THE
TENSION PIN CAN BE EASILY REMOVED (FIG. 1).
2. MOUNT THE DOOR LEAF TO THE DOOR FLANGE. THE DOOR LEAF MAY BE MORTISED OR SURFACE APPLIED AND
MUST BE CENTERED BETWEEN THE AXIAL CENTERS OF THE DOUBLE ACTING HINGE.
3. ALIGN THE DOOR CENTERLINE WITH THE CENTERLINE OF THE FRAME. ATTACH THE JAMB FLANGE TO THE
SURFACE OF THE DOOR CASING. SHIMS UNDER THE JAMB FLANGES MAY BE NECESSARY FOR PROPER DOOR
ALIGNMENT.
4. THE HINGES SHOULD BE MOUNTED AT THE HEIGHT LOCATIONS DESIGNATED IN FIG. 2.
5. THE AXIAL CENTER OF EACH HINGE MUST ALSO BE VERTICALLY ALIGNED.

SPRING ADJUSTMENT TENSIONING INSTRUCTIONS:
1. PLACE DOOR IN THE CLOSED POSITION AND WEDGE UP FROM THE FLOOR UNTIL IT IS PLUMB.
2. INSERT TENSION ROD INTO THE ADJUSTMENT HOLES ON THE TENSION LUG AND TURN IN THE CORRECT
DIRECTION (FIG. 1). TURN IT TOWARDS THE LEFT WHEN THE HINGE IS MOUNTED WITH THE TENSION LUG AT THE
TOP AND TOWARDS THE RIGHT WHEN IT IS MOUNTED WITH THE TENSION LUG AT THE BOTTOM. ONE HOLE OF
TENSION IS RECOMMENDED FOR THE BOTTOM HINGES. DO NOT EXCEED FIVE HOLES OF TENSION.
3. INSERT TENSION PIN AND REMOVE TENSION ROD.
4. INCREASE TENSION ON TOP HINGE IF THE DOOR SAGS OR RETURN ACTION IS TOO SLOW.
CAUTION: IMPROPER USE OR MOUNTING MAY CAUSE INJURY!
B DO NOT USE ON DOORS WITH HINGE EDGE BEVELED.

B

1/4” [6MM] MORTISED
5/16” [8MM] NON-MORTISED

7” [177MM]

FIG. 2

DESCRIPTION

INSTALLATION INSTRUCTIONS:

JAMB

JAMB

REV.

HINGE SIZE
3”
4”
5”
6”
HAGER RESERVES THE RIGHT TO
MAKE DESIGN CHANGES WITHOUT
NOTICE. CALL HAGER ENGINEERING
AT 1-800-325-9995 FOR THE LATEST
REVISION DATE OF TEMPLATE.
PRIMARY DIMENSIONS SHOWN IN INCHES,
DIMENSIONS IN [ ] ARE MILLIMETERS.

DOOR MORTISE DEPTH
5/64”
5/64”
3/32”
7/64”
DRAWN

DMH

01-27-06

ENG. APPR.
MATERIAL
FINISH

N/A
N/A

DO NOT SCALE DRAWING

Q.A.

TOLERANCES:
FRACTIONAL:
0.015”
ANGULAR: MACH:
1 BEND 1
TWO PLACE DECIMAL:
0.01”
THREE PLACE DECIMAL:
0.004”

1303 DBL ACT SPRING HINGE
INSTALLATION INSTRUCTIONS
SIZE

B

DWG. NO.

1-1303 DBL_ACT_SPRING_HINGE

SCALE: 1:4

WEIGHT: N/A

SHEET 1 OF 1

REV.

B
Source Exif Data: 
File Type                       : AI
File Type Extension             : ai
MIME Type                       : application/vnd.adobe.illustrator
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : 3.1.1-111
Format                          : application/pdf
Creator                         : 
Title                           : I-1303 DBL_ACT_SPRING_HINGE_REVB
Creator Tool                    : Adobe Illustrator CS2
Create Date                     : 2008:01:02 13:55:44-06:00
Modify Date                     : 2008:01:02 13:55:44-06:00
Metadata Date                   : 2008:01:02 13:55:44-06:00
Thumbnail Width                 : 256
Thumbnail Height                : 152
Thumbnail Format                : JPEG
Thumbnail Image                 : (Binary data 15990 bytes, use -b option to extract)
Document ID                     : uuid:FA2A382CB65511DC855A84EB262F6E80
Instance ID                     : uuid:b4278068-b96c-11dc-a7f7-0017f20e6f7c
Derived From Instance ID        : uuid:FA2A382BB65511DC855A84EB262F6E80
Derived From Document ID        : uuid:FA2A3826B65511DC855A84EB262F6E80
Revision                        : B
Producer                        : Adobe PDF library 7.77
Page Count                      : 1
Creator Version                 : 12
Container Version               : 9
For                             : Mac User, Hager Companies
Bounding Box                    : 26 17 985 580
Author                          : 
Image Height                    : 563
Image Width                     : 959
Image Size                      : 959x563
Megapixels                      : 0.540
EXIF Metadata provided by EXIF.tools

Navigation menu