Halsey Taylor Ovl Ii Er Q Users Manual 97793C
OVL-II SR-Q to the manual 952d709d-24b5-49a2-af67-dcc3190066fe
2015-02-09
: Halsey-Taylor Halsey-Taylor-Ovl-Ii-Er-Q-Users-Manual-563370 halsey-taylor-ovl-ii-er-q-users-manual-563370 halsey-taylor pdf
Open the PDF directly: View PDF 
.
Page Count: 12
| Download | |
| Open PDF In Browser | View PDF |
OVLERQ*C OVLSRQ*C OVLESRQ*F OVLSERQ*F HALSEY TAYLOR OWNERS MANUAL OVLTM Series Barrier-Free Water Coolers Refrigerated Fountains with Back Panel Figure 1 OVL-II ER-Q Figure 2 OVL-II SR-Q Figure 3 OVLII SER-Q Figure 4 OVL-II ESR-Q Figure Model Description 1 2 OVL-II ER-Q OVL-II SR-Q OVL-II Series - Extended Reach OVL-II Series - Standard Reach 3 4 OVL-II SER-Q OVL-II ESR-Q OVL-II Series - Dual Installation OVL-II Series - Dual Installation INSTALLER ! CAUTION: Review these instructions before beginning installation. Be sure that installation conforms to all plumbing, electrical and other applicable codes. ! WARNING: When installation is complete, ensure these instructions are left in the plastic bag provided inside the installed unit for future reference. ! WARNING: Service to be performed by authorized service personnel only. NOTE: It is common practice to ground electrical hardware such as telephones, computers and other devices to available water lines. This can, however, cause electrical feedback in the plumbing circuit, which results in an electrolysis effect occurring in the fountain. This may result in water which has a metallic taste to it or has a noticeable increase in the metallic content of the water. When inspecting plumbing circuit, remember the line may be grounded some distance from the installation, and may occur outside the building or area in which the unit is being installed. This condition can be avoided (in most cases) by using recommended materials during installation. Any drain fittings provided by the installer should be made of plastic which will electronically isolate the fountain from the remainder of the buildings plumbing circuits. 1 97793C - 10/01 OVLERQ*C OVLSRQ*C OVLESRQ*F OVLSERQ*F 1/4" O.D. TUBE WATER INLET TO COOLER 3/8" O.D. UNPLATED COPPER TUBE CONNECT COLD WATER SUPPLY Installation Package The components for installation are packed in three separate boxes, regardless of the type of unit being installed. The boxes contain the following: BUILDING WATER INLET NOTE: WATER FLOW DIRECTION Box No. 1: Wall Frame(s) Box No. 2: Remote Chiller, SJ8-Q Box No. 3: Fountain(s), Arm(s) and Panels SERVICE STOP (NOT FURNISHED) Additional materials, as noted in the Parts List, are also shipped in these boxes. Figure 5 Water Supply Connections Parts List Item Part No. OVL-II SR-Q OVL-II SER-Q OVL-II ESR-Q See Fig. Bottom Cover Standard Reach - 1 1 1 23 26988C Bottom Cover Extended Reach 1 - 1 1 23 55836C Push Arm Actuator 1 1 2 2 20 55991C Push Arm Actuator A.G. 1 1 2 2 20 51546C Bubbler S.S. 1 1 2 2 23 45396C Bubbler A.G. 1 1 2 2 23 Bubbler EasyFlex (option) 1 1 2 2 - 100322740560 Bubbler Gasket 1 1 2 2 23 160270508640 Strainer Plate S.S. 1 1 2 2 23 2 3 5 OVL-II ER-Q 26990C 1 4 Description Number Required Strainer Plate A.G. 1 1 2 2 23 6 101570540560 Drain Gasket 1 1 2 2 23 7 51575C Packing Ring 1 1 2 2 23 8 110346220550 Drain Nut 1 1 2 2 23 9 101637451550 Friction Ring 1 1 2 2 23 161637308640 Drain Plug S.S. 1 1 2 2 23 45398C Drain Plug A.G. 1 1 2 2 23 45683C Drain Tube 1 - 1 1 23 45682C Drain Tube - 1 1 1 23 10 45400C 11 12 100023340560 Waste Tube Gasket 1 1 2 2 23 13 161570808550 Slip Nut 1 1 2 2 23 14 61314C Regulator 1 1 2 2 22 15 50986C Regulator Holder 1 1 2 2 22 27006C Basin S.S. 1 1 2 2 23 27342C Basin A.G. 1 1 2 2 23 Basin Galaxy Gray Marblyte (option) 1 1 2 2 - Basin Golden Sand Marblyte (option) 1 1 2 2 - Basin Black Onyx Marblyte (option) 1 1 2 2 - 27000C Basin Liner S.S. 1 1 2 2 23 27344C Basin Liner A.G. 1 1 2 2 23 16 17 97793C - 10/01 Basin Liner Galaxy Gray Marblyte (option) 1 1 2 2 - Basin Liner Golden Sand Marblyte (option) 1 1 2 2 - Basin Liner Black Onyx Marblyte (option) 1 1 2 2 - 2 OVLERQ*C OVLSRQ*C OVLESRQ*F OVLSERQ*F Parts List Continued OVL-II ER-Q OVL-II SR-Q OVL-II SER-Q OVL-II ESR-Q See Fig. Screw #10-24 x 2 1 1 2 2 23 Top Plate Actuator 1 1 2 2 20 Bottom Plate Actuator 1 1 2 2 20 Extended Reach Arm S.S. 1 - 1 1 23 Extended Reach Arm A.G. 1 - 1 1 23 27004C Standard Reach Arm S.S. - 1 1 1 23 27340C Standard Reach Arm A.G. - 1 1 1 23 22 26992C Regulator Mounting Bracket 1 1 2 2 21 23 15005C Nut Retaining 1 1 2 2 22 24 40045C Hex Nut Unplated 1 1 2 2 22 25 27008C Reaction Bracket 1 1 2 2 21 26 70856C Screw #10-24 x 0.38 PHMS 1 1 2 2 21 27 70854C Rod Pivot 1 1 2 2 21 28 50198C Bushing Snap 1 1 2 2 21 29 51468C Bumper Regulator Valve Assy 1 1 2 2 21 30 22646C Regulator Arm Assembly 1 1 2 2 21 31 22635C Arm Regulator Adjustment 1 1 2 2 21 22797C Upper Panel (OVL-II ER) S.S. 1 - - - 13, 23 27885C Upper Panel (OVL-II ER) A.G. 1 - - - 13, 23 22799C Upper Panel (OVL-II SR) S.S. - 1 - - 13, 23 27887C Upper Panel (OVL-II SR) A.G. - 1 - - 13, 23 26958C Upper Panel (OVL-II SER) S.S. - - 1 - 13, 23 27889C Upper Panel (OVL-II SER) A.G. - - 1 - 13, 23 22795C Upper Panel (OVL-II ESR) S.S. - - - 1 12, 23 27891C Upper Panel (OVL-II ESR) A.G. - - - 1 12, 23 26833C Lower Panel (OVL-II ER-Q/SR-Q) S.S. 1 1 - - 15, 23 27893C Lower Panel (OVL-II ER-Q/SR-Q) A.G. 1 1 - - 15, 23 27026C Lower Panel (OVL-II SER-Q/ESR-Q) S.S. - - 1 1 15, 23 27895C Lower Panel (OVL-II SER-Q/ESR-Q) A.G. - - 1 1 15, 23 34 55996C Strainer 1 1 2 2 17, 18 35 70870C Union 3/8 1 1 - - 17 36 70745C Union 3/8 x 1/4 1 1 1 1 17, 18 Item Part No. 18 70861C 19 55840C 20 55839C 27002C 27338C 21 32 33 Description 37 70852C Tee 3/8 - - 1 1 18 N-S 27089C Upper Panel Hanger Bracket 1 1 - - - N-S 27090C Upper Panel Hanger Bracket - - 1 1 - N-S 15008C Bubbler Nipple Assembly 1 1 2 2 - N-S 56092C Tubing Poly (Cut To Length) 1 1 1 1 - NOTE: S.S. means Stainless Steel A.G. means Aztec Gold N-S means not shown. 3 97793C - 10/01 OVLERQ*C OVLSRQ*C OVLESRQ*F OVLSERQ*F Models OVL-II SER-Q OVL-II ESR-Q 1. Cut a rectangular wall opening 37-1/2 (953 mm) W x 37-3/4 H (959 mm) and 4-1/2 (114 mm) above the floor line (see Figure 7). The dimensions are required to obtain proper rim and bubbler heights for compliance with ANSI standard A117.1. 2. Reinforce the wall opening on all sides to adequately support the water fountain. This reinforcement must support up to 150 lbs. static load and provide a means for securing the frame assembly in place. NOTE: Figure 6 OVL-II SER-Q Rough-In Building construction must allow for adequate air flow on both sides and top of remote chiller unit a minimum of 4 (102 mm) is required. 3. Install plumbing and electrical rough-ins. A junction box for a (3) wire, 10 amp branch circuit is provided on the inside of the chiller. (Standard 120 Volts, 60 Hz, and single phase.) 4. Remove frames and related hardware from packaging. Release the two shelf rods by cutting cable ties. Attach the two frames together through the upright supports with (4) 5/16 x 3/4 (19 mm) long bolts and nuts (not provided). Tighten securely. MAKE SURE FRAME CONFIGURATION MATCHES THE COOLER TO BE INSTALLED REVERSED CONFIGURATION: HIGHER UNIT ON THE RIGHT STANDARD CONFIGURATION: HIGHER UNIT ON THE LEFT Figure 7 Rough-In Assembly Dual-Station Mounting Frames 97793C - 10/01 4 5. OVLERQ*C OVLSRQ*C OVLESRQ*F OVLSERQ*F Install the frame assembly squarely in wall opening with frame upright support edges flush with the finished wall face. Secure the frame to the wall through holes with (12) 5/16 bolts or screws (not provided). Tighten securely. NOTE: 6. Be sure that frame is squared in location. Do not use less than required screw quantity and size. Attach the chiller shelf support rods to the right side of the frame uprights at the second set of holes counting from the bottom and to the shelf at the (2) side holes. Line up the other shelf holes with the frame bottom holes and fasten the assembly to the wall opening using appropriately sized screws or bolts and nuts (not provided). Legend Item Description A B 3/8 O.D. Tube - Water Outlet Connection 3/8 O.D. Tube - Water Inlet Connection C D 1-1/4 O.D. Tube - Waste Tube - Not provided Electrical Inlet on Chiller Figure 8 OVL-II SER-Q/OVL-II ESR-Q Rough-In Dimensions 5 97793C - 10/01 OVLERQ*C OVLSRQ*C OVLESRQ*F OVLSERQ*F Models OVL-II ER-Q OVL-II SR-Q 1. Cut a rectangular wall opening 18-3/4 (475 mm) W x 37-3/4 H (959 mm) and 4-1/2 (114 mm) above the floor line (see Figure 10). The dimensions are required to obtain proper rim and bubbler heights for compliance with ANSI standard A117.1. 2. Reinforce the wall opening on all sides to adequately support the water fountain. This reinforcement must support up to 150 lbs. static load and provide a means for securing the frame assembly in place. NOTE: Building construction must allow for adequate air flow on both sides and top of remote chiller unit. Minimum of 4 (102 mm) is required. Figure 9 OVL-II ER-Q/OVL-II SR-Q Rough-In 97793C - 10/01 3. Install plumbing and electrical rough-ins. A junction box for a (3) wire, 10 amp branch circuit is provided on the inside of the chiller. (Standard 120 Volts, 60 Hz, and single phase.) 4. Remove frame and related hardware from packaging. Release the two shelf rods by cutting cable ties. Figure 10 Rough-In Assembly Single-Station Mounting Frames 6 OVLERQ*C OVLSRQ*C OVLESRQ*F OVLSERQ*F 5. Install the frame squarely in wall opening with frame upright edges flush with the finished wall surface. Place shelf inside frame and line up the (2) holes on each. Insert loose ends of rods into holes on sides of shelf panel. Using appropriately sized screws or bolts (not provided), fasten the shelf and frame to the bottom of wall opening. Secure the frame sides and top to the wall opening using (10) 5/16 bolts or screws (not provided). NOTE: MODEL OVL-ER Legend Item A B C D Be sure that frame is squared in location. Do not use less than the required screw quantity and size. MODEL OVL-SR Description 3/8 O.D. Tube - Water Outlet Connection 3/8 O.D. Tube - Water Inlet Connection 1-1/4 O.D. Tube - Waste Tube - Not provided Electrical Inlet on Chiller Figure 11 OVL-II ER-Q/SR-Q Rough-In Dimensions 7 97793C - 10/01 OVLERQ*C OVLSRQ*C OVLESRQ*F OVLSERQ*F REQUIRED TOOLS AND MATERIALS 5. Install fountain: Remove access cover plate on underside of fountains and SAVE the screws. Mount the fountains to the upper panel and frame with (4) 5/16 x 3/4 (19mm) long bolts and nuts provided. Tighten securely. These tables show special tools and/or additional materials (not provided) which are necessary to complete installation of these units: Special Tools Item Description Quantity NONE Additional Materials Item Description 1 Unplated copper inlet pipe 2 Service Stop Quantity OVL-II ER-Q/SR-Q/SER-Q/ESR-Q INSTALLATION 1. 2. Assemble and place frame in wall as shown on preceding pages. Install chiller: Remove front panel of chiller. Remove and discard cardboard inner pack from between compressor and side panel. Slide chiller onto the shelf and position it to the left within the guides on the shelf. NOTE: Building construction must allow for adequate air flow on both sides, top and back of chiller. A minimum of 4 (102mm) on both sides and top is required. See chiller installation for additional instructions. Figure 13 Upper Panel Installation Note: With OVL-II SER-Q or OVL-II ESR-Q models, the standard reach fountain must be mounted at the upper position on panel. Figure 12 Chiller Installation 3. 4. Make water supply connections: Attach an unplated copper water inlet line and a service stop (not provided) to the chiller. Inlet port is marked on the chiller (3/8 O.D. copper tube). Bend the copper tube (provided) at an appropriate length from the chiller to opening in frame. Install a 3/8 O.D. tube tee fitting (provided) on the marked chiller outlet port. Turn on the water supply and flush the line thoroughly. Figure 14 Fountain Installation Hang the upper panel on the mounting frame hanger: Align holes in the panel with the holes in the mounting frame. Be sure that panel is engaged with hanger at top of frame before releasing it. 97793C - 10/01 8 6. Remove elbow from end of p-trap and attach it to drain tube. Re-attach elbow to p-trap and cut waste tube to required length using plumbing hardware and trap as a guide. 7. Make connection between remote chiller outlet tube and fountain strainer. Insert the water inlet line into inlet side of strainer by pushing it in until it reaches a positive stop, approximately 3/4 (19mm). Turn on water supply and check for leaks. OVLERQ*C OVLSRQ*C OVLESRQ*F OVLSERQ*F ! CAUTION: DO NOT SOLDER tubes into the strainer as damage to o-rings may result. 8. These products are designed to operate on 20-105 PSIG supply line pressure. If inlet pressure is above 105 PSIG, a pressure regulator must be installed in the supply line. ! CAUTION: Any damage caused by connecting these products to a supply line with pressure lower than 20 PSIG or higher than 105 PSIG IS NOT covered under warranty. 9. Figure 16 Stream Height TO BUBBLER Make electrical connections to the chiller. See chiller instructions. 10. Check stream height from bubbler. Stream height is factory set at 45-50 PSI. If supply pressure varies greatly from this, remove items 2, 19, and 20 (push arm and the bottom and the top actuator plates Figure 20) by removing the screws holding assembly together and adjust the screw on the regulator (Item 26 Figure 21). Clockwise adjustment will raise stream height and counterclockwise movement will lower stream height. For best adjustment, stream height should be approximately 1-1/2 (38mm) above the bubbler guard. (See Figure 16). 34 35 CHILLER OUTLET 36 CHILLER INLET 11. Mount lower panel. Loosen the two (2) #10-24 x 5/8 (16mm) screws at frame bottom lip. Slide upper tongue of lower panel under lower edge of already installed upper panel. Tighten previously loosened screws securely. 12. Replace bottom access panel to fountain basin using screws provided. Tighten securely. Figure 17 OVL-II ER-Q/SR-Q Tube Routing TO BUBBLER TO BUBBLER 34 37 CHILLER OUTLET 36 CHILLER INLET Figure 18 OVL-II SER-Q/ESR-Q Tube Routing Figure 15 Lower Panel Installation 9 97793C - 10/01 OVLERQ*C OVLSRQ*C OVLESRQ*F OVLSERQ*F TROUBLESHOOTING & MAINTENANCE Orifice Assembly: Mineral deposits on orifice can cause water flow to spurt or not regulate. Mineral deposits may be removed from the orifice by poking with a small round file not over 1/8 diameter, or using a small diameter wire. ! CAUTION: DO NOT file or cut orifice material. Stream Regulator: If orifice is clean, regulate flow as in Step 10 of the installation instructions. If replacement is necessary, see parts list for correct regulator part number. ! CAUTION: Cleaning of Aztec Gold Models requires special care. Outer surfaces must be cleaned with mild detergent or a mixture of vinegar and water only, rinsed and wiped dry. Abrasive and acidic cleaners may eventually damage the Aztec Gold finish. Figure 20 Push Arm Mechanism Actuation of Quick Connect Water Fittings: Cooler is provided with lead-free connectors which utilize an o-ring water seal. To remove tubing from the fitting, relieve water pressure, push in on the gray collar while pulling on the tubing. (See Figure 19) To insert tubing, push tube straight into fitting until it reaches a positive stop (approximately 3/4). SIMPLY PUSH IN TUBE TO ATTACH TUBE IS SECURED IN POSITION 28 PUSH IN COLLET TO RELEASE TUBE PUSHING TUBE IN BEFORE PULLING IT OUT HELPS TO RELEASE TUBE Figure 19 Quick Connect Fittings Figure 21 Regulator Mounting Mechanism 97793C - 10/01 10 OVLERQ*C OVLSRQ*C OVLESRQ*F OVLSERQ*F 23 15 24 14 REGULATOR MOUNTING BRACKET Figure 22 Regulator Assembly 32 16 3, 4 See Fig. 22 21 17 See Fig. 20 18 1 5 10 See Fig. 21 6 7 8 9 8 12 13 11 Figure 23 Fountain Assembly - Side View 11 97793C - 10/01 OVLERQ*C OVLSRQ*C OVLESRQ*F OVLSERQ*F 2222 CAMDEN COURT OAK BROOK, IL 60523 630.574.3500 PRINTED IN U.S.A. 97793C - 10/01 FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620 12
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 12 Create Date : 1910:11:20 40:75:22 Producer : Acrobat Distiller 3.02 Subject : 97793C Author : BLF Creator : Adobe PageMaker 6.52 Title : 97793CEXIF Metadata provided by EXIF.tools