Hanchett Entry Systems RF0010 Prox Reader User Manual FCC Part 15
Hanchett Entry Systems, Inc. Prox Reader FCC Part 15
Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1369957 |
| Application ID | S/CWOFV8WQUggeh1NlEZSQ== |
| Document Description | Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 50.52kB (631550 bits) |
| Date Submitted | 2010-11-02 00:00:00 |
| Date Available | 2010-11-03 00:00:00 |
| Creation Date | 2010-10-08 09:50:28 |
| Producing Software | Adobe Acrobat 8.1 |
| Document Lastmod | 2010-10-08 09:50:28 |
| Document Title | FCC Part 15 |
| Document Creator | Adobe Acrobat 8.1 Combine Files |
| Document Author: | Brooke Copeland |
Certification Exhibit FCC ID: VC3-RF0010 IC: 7160A-RF0010 FCC Rule Part: 15.209 IC Radio Standards Specification: RSS-210 ACS Report Number: 10-0242.W06.12.A Manufacturer: Hanchett Entry Systems, Inc Model: RF0010 Manual 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Installation Instructions RF0010 HES, Inc. 22630 N. 17th Ave. Phoenix, AZ 85027 800-626-7590 Prox Module Prox Module Dielectric Grease (for humid applications) #6-32 Module Mounting Screws (for optional strike mount) Reader/Antenna Body Reader/Antenna Mounting Screws Reader/Antenna Cover 24” Cable (connecting reader/antenna and strike) 2 pin DPS & LBM Pigtail Connector 10 11 4 pin 12V Strike Power Pigtail 8 pin Connector (Data Module) Prox Pigtail Door Position Sensor (DPS) 10 Access Control System Control Panel and Power Supply (By others) Dielectric Grease 11 The Prox Module can either be supported by the electrical connection to the Electric Strike, or by mounting it directly to the back of several HES Electric Strikes using the #6-32 Module Mounting Screws. Do not attempt to support the Prox Module with the 24” Antenna Cable. To Electric Strike Wiring Diagram 8 Pin Connector (Data Module) Red Black Green White Yellow Blue Orange Brown (+) Board Power (- ) Board Power Data 0 Data 1 LED/Buzzer Not Used Not Used Not Used 2 pin Connector (Strike Module) Tan Pink Common Door Closed and Latch Engaged 4 Pin Connector (12V Strike Power) Red (12VDC +) Black (−) Strike Power Strike Power OR 2 Pin Connector (Door Position Switch) Wire plugs into Hybrid Electric Strike 4 Pin Connector (24V Strike Power) Violet (24VDC +) (−) Black Strike Power Strike Power Installation Directions RF0010: Prox Module Prepare Frame and Strike Connect Components and Wiring 1. Prepare door jamb for the Electric Strike per the appropriate template provided with the electric strike. 2. Drill a 1” diameter hole for Reader/Antenna install per the image below The Reader/Antenna may be positioned as desired, within the limits of the 24”cable connected to the Prox Module. 5. Select the 12V AC/DC pigtail. 1-5/16” 33 5/8” 17 DPS: 3/8” [10] 1” 25 Reader/Antenna 3. The Prox Module can be mounted directly to the back of the several HES Electric Strikes, or supported in the frame by its electrical connection to the Electric Strike. Do not attempt to support the Prox Module with the 18” Antenna Cable. To attach the Prox Module to the Electric Strike, see page 1. 6. Verify that the wires running from the control panel are of adequate wire gauge (see Wire Gauge Diagram below). Connect the wire leads of the three pigtails provided to the control panel wiring based on the wiring diagram on page 2 and the appropriate termination at the control panel. 7. Mount the door position switch (DPS) into the frame. Route the 10” cable back to the Electric Strike and connect it to the 2 pin connector coming out of the Electric Strike. It does not matter which 2 pin connector is used. The LBM & DPS are wired in series--a ‘closed’ electrical circuit depicts a closed door and extended latchbolt into the hybrid Electric Strike. 8. Secure the Reader/Antenna Mounting Plate to the frame using the #6-32 screws provided. Connect the 24” cable to the Reader/Antenna, snap the Reader/Antenna to the Reader/Antenna Mounting Plate and pull the 24” cable through to the Prox Module. 9. Attach the 8, 4 and 2 pin connectors at the Electric Strike to the equivalent pigtail connectors routed from the control panel. Dielectric grease should be applied to the pigtail electrical terminals if used in a humid environment. 10. Install the Electric Strike unit in jamb cutout. Testing and Operation 4. Drill a 3/8” hole for the door position switch (DPS) as required. 11. When power is supplied, the LED will turn red, while the beeper beeps 3 times. This sequence indicated the micro-controller is operating properly. Wire Gauge Diagram 1. Present an Prox ID card to the Reader/Antenna. The LED will turn green, while the beeper beeps once. This indicates 24VDC Distance In ft, Round Trip 12VDC that the card was read successfully. Simultaneously, the 24 Gauge 24 Gauge 100’ or less 24 Gauge 22 Gauge 100’ to 200’ keeper will click open. This indicates that communication 24 Gauge 22 Gauge 200’ to 300’ between the control panel and the Electric Strike is 22 Gauge 22 Gauge 300’ to 400’ operational. 22 Gauge 20 Gauge 400’ to 500’ 500’ to 600’ 20 Gauge 22 Gauge 600’ to 700’ 18 Gauge 20 Gauge Warning Changes or modification to this device not expressly approved by HES, Inc., could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a class [B] digital device, pursuant to Part15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed andused in accordance with the instructions, may cause harmful int erference to radio communications. However, there is no guarantee that interference will not occur in a particular inst allation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help This class [B] digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareillage numérique de la classe [B] répond à toutes les exigences de l’inerférencé canadienne causant des réglements d’équipement. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l’interférence nocive, et (2) ce dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence quipeut causer l’opération peu désirée. 3078006.009 rev A © 2010 HES, Inc.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Tagged PDF : No XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Modify Date : 2010:10:08 09:50:28-04:00 Create Date : 2010:10:08 09:50:28-04:00 Metadata Date : 2010:10:08 09:50:28-04:00 Creator Tool : Adobe Acrobat 8.1 Combine Files Format : application/pdf Title : FCC Part 15 Creator : Brooke Copeland Document ID : uuid:9479eb42-84ca-40f6-9524-249fd344fc6a Instance ID : uuid:86633b26-f0b8-4b97-a256-a7da20a5ec51 Producer : Adobe Acrobat 8.1 Page Count : 3 Creator Version : 14 Container Version : 11 For : Josh Peabody, Bounding Box : -894 -93 1254 2010 Author : Brooke CopelandEXIF Metadata provided by EXIF.tools