Handlink Technologies WAP-001R2 In Wall Box Access Point User Manual

Handlink Technologies Inc. In Wall Box Access Point

UserManual.wiki >

Handlink Technologies >

WAP 001R2 User Manual

User manual

In Wall Box Access Point 2 Table of Contents 1Introduction ------------------------------------------------------------------------------------------------------------41-1Package Contents ---------------------------------------------------------------------------------------------------41-2Features ----------------------------------------------------------------------------------------------------------------51-3Precautions------------------------------------------------------------------------------------------------------------51-4Outlook------------------------------------------------------------------------------------------------------------------51-4-1Rear Panel---------------------------------------------------------------------------------------------------71-5Technical Specifications -------------------------------------------------------------------------------------------71-5-1Hardware Specifications ---------------------------------------------------------------------------------71-5-2Software Specifications ----------------------------------------------------------------------------------82Installation -----------------------------------------------------------------------------------------------------------102-1Installation Requirements----------------------------------------------------------------------------------------112-2Getting Start---------------------------------------------------------------------------------------------------------123 Configuring the In Wall Access Point -----------------------------------------------------------------------------153-1Internet Settings----------------------------------------------------------------------------------------------------173-2Wireless --------------------------------------------------------------------------------------------------------------203-2-1Wireless Basic Setting----------------------------------------------------------------------------------203-2-2Wireless Advanced Setting----------------------------------------------------------------------------213-2-3Multi-SSID Settings -------------------------------------------------------------------------------------223-3Advanced ------------------------------------------------------------------------------------------------------------243-3-1Management ----------------------------------------------------------------------------------------------243-3-2Daily Report -----------------------------------------------------------------------------------------------263-3-3FTP ----------------------------------------------------------------------------------------------------------273-3-4SNMP -------------------------------------------------------------------------------------------------------283-4System Tool ---------------------------------------------------------------------------------------------------------293-4-1Configuration----------------------------------------------------------------------------------------------293-4-2Firmware ---------------------------------------------------------------------------------------------------303-4-3Ping Command-------------------------------------------------------------------------------------------323-4-4Restart ------------------------------------------------------------------------------------------------------32Appendix A Signal Connection Arrangements -------------------------------------------------------------------- 33

In Wall Box Access Point 3 Appendix B Regulations/EMI Compliance -------------------------------------------------------------------------34LIMITED WARRANTY---------------------------------------------------------------------------------------------------35

In Wall Box Access Point 4 1 Introduction The WAP-001 Access Device revolutionizes the way wireless and wired IP-based services are delivered to hospitality and residential properties. The WAP-001 integrates wired and wireless connectivity into a small unit that can be quickly and discretely installed in a standard wall box. The WAP-001 provides Two Ethernet ports, a 2.4GHz 802.11b/g/n wireless access point. The WAP-001 requires a single powered cable drop to unlock its utility and, through the reduction in cabling, switch ports, and power-sourcing equipment, the WAP-001 represents the best value for the delivery of next generation entertainment services. 1-1 Package Contents Please inspect your package. The following items should be included: ◎ WAP-001 z One In Wall Box Access Point z One UTP Ethernet/Fast Ethernet cable (Cat.5 Twisted-pair) (10cm) z One Wall fixed plate z One Quick Installation Guide z One CD Contents If any of the above items are damaged or missing, please contact your dealer immediately.

In Wall Box Access Point 5 1-2 Features z Wireless data rates up to 300Mbps z Comprehensive security 64/128-bit WEP encryption WPA encryption WPA2 encryption z Intelligent Management 1-3 Precautions z Never remove or open the cover. You may suffer serious injury if you touch these parts. z Never install the system in the wet locations. 1-4 Outlook Front Panel The Front panel of the In Wall Box Access Point shown below. Figure 1 in Wall Box Access Point Front Panel

In Wall Box Access Point 6 Figure 2 In Wall Box Access Point Front Panel LEDs Indication LED State Description Off The In Wall Box Access Point not receiving electrical power. PWR Green The In Wall Box Access Point receiving electrical power. Off The In Wall Box Access Point status is defective. Green The In Wall Box Access Point status is complete. SYS Green (Blinking) During firmware upgrades, this system LED will blink. Off Port has not established any network connection. Yellow A port has established a valid 10/100Mbps network connection. LINK / WAN Yellow (Blinking) 10/100Mbps traffic is traversing the port. Off Port has not established any network connection. Green A port has established a valid 10/100Mbps network connection. LAN Green (Blinking) 10/100Mbps traffic is traversing the port. Off The Wireless is not ready. WLAN Green The In Wall Box Access Point has established a valid wireless 1. RJ-45 Transparent Port 2. RJ-45 Ethernet Connector 3. WPS Button 4. Reset Button 5. WLAN 6. SYSTEM 7. POWER 8. LAN Port 9. LINK Port

In Wall Box Access Point 7 connection. Green (Blinking) The Wireless connection is active. 1-4-1 Rear Panel The rear panel of the In Wall Access Point Figure 3 In Wall Box Access Point Rear Panel 1-5 Technical Specifications 1-5-1 Hardware Specifications Network Specification IEEE802.3 10 Base TX Ethernet IEEE802.3u 100 Base TX Fast Ethernet IEEE802.3af Power over Ethernet IEEE802.11b Wireless LAN IEEE802.11g Wireless LAN IEEE802.11n Wireless LAN ANSI/IEEE 802.3 NWay auto-negotiation Static IP Client DHCP Client Wi-Fi Compatible Connectors One LAN Port (10BaseT/100BaseTX Auto cross-over) One LINK Port (10BaseT/100BaseTX Auto cross-over) Two RJ-45 transparent used 10. RJ-45 Ethernet Connector(802.3af PoE) 11. RJ-45 transparent

In Wall Box Access Point 8 Encryption WEP (Wired Equivalent Privacy) 64/128-bit RC4 WPA (Wi-Fi Protected Access) WPA2 (Wi-Fi Protected Access) WPA/WPA2 Mixed Mode WMM LED Indicators One POWER LED One Link 10/100M Link/Activity LED One LAN 10M/100M Link/Activity LED One Wireless Link/Activity LED One System LED Environment Conditions Operating Temperature: 0 to 50°C Storage Temperature: -10 to 60°C Operating Humidity: 10~80% non-condensing Storage Humidity: 10% to 90% non-condensing Certifications FCC part 15 Class B, Dimension Size: 39.3(W) x 71.6(L)x 55(H)/ mm Weight: About 85g (Net) 1-5-2 Software Specifications Networking • IEEE802.3 10BaseT Ethernet • IEEE802.3u 100BaseTX Fast Ethernet • IEEE802.3af Power over Ethernet • IEEE802.11b Wireless LAN • IEEE802.11g Wireless LAN • IEEE802.11n Wireless LAN • Static IP WAN Client • DHCP WAN Client

In Wall Box Access Point 9 Security and Firewall • WEP • WPA • WPA2 • WPA/WPA2 Mixed Mode • WMM Management • Web-based Management Tool • Firmware Upgrade via HTTP/TFTP • Backup/Restore/Factory Default Setting • Remote Authorized Management • SNMP • System Information Table

In Wall Box Access Point 10 2 Installation The followings are instructions for setting up the In Wall Access Point. Refer to the illustration and follow the simple steps below to quickly install your In Wall Access Point. Step 1：Slide the Bracket to align with screw holes on the In Wall Access Point, and fasten the Bracket tightly with screws on the In Wall Access Point Step 2：Slide the WAP-001 into the Bottom Faceplate and fasten tightly into the Bottom Faceplate until it’s flushed into the wall. Step 3：Line-up and push the Top faceplate onto Bottom faceplate until snaps securely into place.

In Wall Box Access Point 11 2-1 Installation Requirements Before installing the In Wall Access Point, make sure your network meets the following requirements. System Requirements The In Wall Box Access Point requires one of the following types of software: z Windows 98 Second Edition/NT/2000/XP/Vista/Win 7 z Red Hat Linux 7.3 or later version z MAC OS X 10.2.4 or later version z Any TCP/IP-enabled systems like Mac OS and UNIX (TCP/IP protocol installed) z Web Browser Software (Microsoft I.E 5.0 or later version or Netscape Navigator 5.0 or later version) z One computer with an installed 10Mbps, 100Mbps or 10/100Mbps Ethernet card z UTP network Cable with a RJ-45 connection (Package contents) Note: Prepare twisted-pair cables with RJ-45 plugs. Use Cat.5 cable for all connections. Make sure each cable not exceed 328 feet (Approximately 100 meters).

In Wall Box Access Point 12 2-2 Getting Start WAP-001 support web-based configuration. Upon the completion of hardware installation, can be configured through PC/NB by web browser such as Internet Explorer, Firefox, and Opera. ¾ Default IP Address:10.59.1.254 ¾ Default Subnet Mask:255.255.255.0 ¾ Default Username and Password: admin/admin Note：Set the IP segment of the administrator’s computer to be in the same range as WAP-001 for accessing the system. Do not duplicate the IP address used here with IP address of WAP-001 or any other device within the network. Step1：Click StartÆSettingÆControl Panel, and then “Control Panel” window appears, Click on “Network connection” window appears. Step2：In “Local Area Connection properties” window, select “Internet Protocol (TCP/IPv4)” and click on “properties” button.

In Wall Box Access Point 13 Step 3：Launch your browser, and then enter the factory default IP address 10.59.1.254 in your browser’s location box. Press Enter. Step 4：.The WAP-001 login screen will appear. In the Username and Password field, type the factory default user name admin and password admin and click Setup. The WAP-001 setup screen will appear. Note: It is important to remember your password. If for any reason you lose or forget your password, press the reset button located on the top of the device. Reset action will re-initialize the settings. All configurations, including username, password and IP address(s), will be reset, and requires re-entering. Example: IP Address:10.59.1.109 Subnet Mask:255.255.255.0 Username: admin Password: admin

In Wall Box Access Point 14 PoE (Power over Ethernet) Application Note: To use the WAP-001’s PoE feature, follow the instructions for your specific PoE device.

In Wall Box Access Point 15 3 Configuring the In Wall Access Point Step 1: Start your browser, and then enter the factory default IP address 10.59.1.254 in your browser’s location box. Press Enter. Figure 4 Web Browser Location Field (Factory Default) Step 2: The In Wall Box Access Point configuration tools menu will appear. In the Username and Password field, type the factory default user name admin and password admin and click Login. Figure 5 Configuration Tools Menu Note: ) This Web agent is best viewed with IE 5.0 or Netscape 6.0 and above browsers. ) Username and Password can consist of up to 20 alphanumeric characters and are case sensitive. ) If for some reason your password is lost or you cannot gain access to the In Wall Box Access Point Configuration Program, please press the reset button to load the device to manufacturer defaults. ) If the In Wall Box Access Point doesn’t send packet in 5 minutes (default), the In Wall Box Access Point will logout automatically. ) Proxy needs to set disable first when administrator accesses admin UI Username: admin Password: admin

In Wall Box Access Point 16 The Setting enables you to configure advanced settings related to accessing the Internet；Display in Wall Box Access Point basic status and process Firmware upgrade, change password and backup or restore configuration. Including, z Network Setting z Wireless Setting ¾ Basic ¾ Advanced ¾ Multi-SSID Setting z Administration Setting ¾ Management ¾ Daily Report ¾ FTP ¾ SNMP z System Tool ¾ Configuration ¾ Firmware Upgrade ¾ Ping ¾ Restart z Logout Figure 6 Configuration Tools Menu

In Wall Box Access Point 17 3-1 Internet Settings The IP address can be manually set or automatically assigned by a DHCP server on the LAN. If you are manually setting the IP address, Subnet mask, and Gateway IP address settings, set them appropriately, so that they comply with your LAN environment. Figure 7 the TCP/IP Setting DHCP Client The device can work as a DHCP client. This allows the device to obtain the IP address and other TCP/IP settings from your switch or IP router. If your device comes with this feature, please enable Use DHCP Client. Figure 8 DHCP Client Setting Screen Item Default Description MTU Setting 1500 MTU (Maximum Transfer Unit) specifies maximum transmission unit size. Static IP

In Wall Box Access Point 18 Figure 9 Static IP Setting Screen Item Default Description IP Address 10.59.1.254 Enter the IP address for the xDSL/Cable connection (provided by your ISP). Subnet Mask 255.255.255.0 Enter the subnet mask for the IP address. Gateway IP Gateway Empty Enter the Gateway IP address for the xDSL/Cable connection Primary DNS Server Empty A primary DNS server IP address for the xDSL/Cable connection Secondary DNS Server Empty A secondary DNS server IP address for the xDSL/Cable connection. If the primary DNS Server IP were not available, meanwhile, Secondary DNS Server IP would start in the same time. MTU Setting 1500 MTU (Maximum Transfer Unit) specifies maximum transmission unit size.

In Wall Box Access Point 19 VLAN ID Setting Item Default Description VLAN ID Disable Enable or Disable Ethernet and wireless VLAN ID Function Ethernet VLAN ID Empty Defines the VLAN ID for the port (1~4095). Management VLAN ID Disable Click Tick to enable management VLAN ID, and defines the VLAN ID port number (1~4095) VLAN aware device on Ethernet port Disable Enable or disable VLAN aware device on Ethernet port

In Wall Box Access Point 20 3-2 Wireless 3-2-1 Wireless Basic Setting Figure 10 Wireless Basic Setting Screen Item Default Description General Settings Country ETSI Select the desired country code. The options are US and ETSI. Channel 6 Select the channel ID for wireless connection. 802.11 Mode 802.11g+802.11b Select the 802.11 mode of following:： -802.11n+802.11g+802.11b -802.11n+802.11g -802.11g+802.11b -802.11n only -802.11g only -802.11b only Channel Width Auto 20/40MHz Select of channel width of Auto 20/40 MHz or 20MHz Transmit Power 14 dBm To Adjust the output power of the system to get the appropriate coverage of your wireless network. Select the value that you need for your environment.

In Wall Box Access Point 21 3-2-2 Wireless Advanced Setting Figure 11 Wireless Advanced Setting Screen Item Default Description Beacon Interval 200 This value valid range is 1 to 1000 indicates the frequency interval of the beacon. RTS Threshold 2347 This value valid range is 256-2342. This setting determines the packet size at which the Wireless Subscriber Gateway issues a request to send (RTS) before sending the packet. A low RTS Threshold setting can be useful in areas where many client devices are associating with the Wireless Subscriber Gateway, or in areas where the clients are far apart and can detect only the Wireless Subscriber Gateway and not each other. Fragmentation Threshold 2446 This setting determines the size at which packets are fragmented. Enter a setting ranging from 256 to 2432 bytes. Use a low setting in areas where communication is poor or where there is a great deal of radio interference. Preamble Type Dynamic preamble The preamble type is a section of data at the head of a packet that contains information and client devices need when sending and receiving packets. The setting menu allows you to select a long, short or dynamic preamble type. Click Apply button to save the new settings.

In Wall Box Access Point 22 3-2-3 Multi-SSID Settings Figure 12 Wireless Security Setting Screen Figure 13 Wireless Security Setting Screen Item Default Description General Setting Active Active or Inactive the ESSID to activation in your network. ESSID Wireless The ESSID is the unique name that is shared among all points in a wireless network. It is case sensitive and must not exceed 32 characters. Broadcast Enable Enable or Disable Broadcast VLAN ID Empty Defines the VLAN ID for the port (1~4095). WMM Disable Enable or Disable WMM Support Intra-BSS Blocking Disable Enable or Disable intra-Bss Blocking.

In Wall Box Access Point 23 Security Setting Security Disable Select disable to allow wireless station to communicate with the device without any data encryption. Select enable to enable WPA or WEP data encryption. WPA/WPA2 /Mixed Mode Encryption Wi-Fi Protected Access Encryption Pre-shared Key Empty Enter a pre-shared key from 8 to 63 case sensitive ASCII characters. Group Key Re-Keying 86400 Seconds Enter a number in the field to set the force re-keying interval. Pre-shared Key Empty Enter a pre-shared key from 8 to 63 case sensitive ASCII characters. Group Key Re-Keying 86400 Seconds Enter a number in the field to set the force re-keying interval. WEP WEP Key 1 This selects which of the Keys the In Wall Box Access Point uses when it transmits. You can change the selected encryption key every now and then to increase the security of your network. Note: You have to configure all WEP keys (1~4), and select one of the four WEP key. Enter 5 characters (case sensitive) for ASCII 64-bit WEP Key. Enter 10 characters (case sensitive) for Hex 64-bit WEP Key. Enter 13 characters (case sensitive) for ASCII 128-bit WEP Key. Enter 26 characters (case sensitive) for Hex 128-bit WEP Key. Click Apply button to save the new settings. Figure 14 Restart Dialog Box Click Apply button, the restart dialog box appears. Click on Apply to restart the system.

In Wall Box Access Point 24 3-3 Advanced 3-3-1 Management Define the In Wall Box Access Point Management configuration Figure 15 Management Setting Screen

In Wall Box Access Point 25 Item Default Description Username admin The username can consist of up to 20 alphanumeric characters and is sensitive. Administrator Setting Password admin The password can consist of up to 20 alphanumeric characters and is sensitive. Date/Time Date (Year/Month/Day) System Date The system date of the In Wall Access Point. The valid setting of year is from 2002 to 2035. Time (Hour:Minute:Second) System Time The system time of the In Wall Access Point. - Click “Get from my Computer” button to correct the system date and time. - Click “Get from NTP server” button to correct the system date and time. NTP Setting Disable Enables or disables NTP (Network Time Protocol) Time Server. Network Time Protocol can be utilized to synchronize the time on devices across a network. A NTP Time Server is utilized to obtain the correct time from a time source and adjust the local time. Server IP/Domain Name Empty Enter the IP address/domain name of NTP server. The maximum allowed characters length is 100. Time Zone GMT-12:00 Select the appropriate time zone for your location. Update Time 0 hours Enter the number of hours for update time. Disable Enables or disables Daylight Saving Time (DST). Daylight Saving Time Month/Day Set the Daylight Saving Time (DST) on the In Wall Access Point. Adjust the begin time and end time. LED Setting Disable Enable or Disable Device LED lighting. Secure administrator IP Addresses Any Options: Any and Specify. Administrator can specify 5 IP addresses or a range to allow remote control access from network. Allow remote user to ping the device Enable This function allows remote user to ping the In Wall Box Access Point through Internet. Ping is normally used to test the physical connection between two devices, to ensure that everything is working correctly.

In Wall Box Access Point 26 3-3-2 Daily Report Figure 16 Daily Report Setting Screen Item Default Description Send the daily report to Syslog Server Disable Enables or disables the syslog server function. Server IP Address Empty Enter syslog server’s IP address. The WG-500P 24Roam will send all of its logs to the specified syslog server. Server MAC Address Empty Enter the syslog server’s MAC address. The WG-500P 24Roam will send all of its logs to the specified syslog server. Server 1 IP Address Empty Enter IP address of first syslog server. Server 2 IP Address Empty Enter IP address of second syslog server. Send to Email Disable Enables or disables the send to e-mail function. E-mail Server IP Address or Empty Enter the SMTP server IP address or domain name. The

In Wall Box Access Point 27 Domain Name maximum allowed characters length is 50. SMTP Port 25 The SMTP port allowed range is 25 or 2500 to 2599. E-mail (SMTP) Server needs to check my account Disable If your SMTP server requires authentication before accepting e-mail, click on check box. These values (username and password) are supplied by your network administrator, SMTP server provider or ISP. Username Empty Enter the username for the SMTP server. The maximum allowed characters length is 64. Password Empty Enter the password for the SMTP server Email From Name Empty Enter the name you would like to appear in the “message from” field of your outgoing message. The maximum allowed characters length is 20. Email Address Empty Enter your e-mail address. This is the address others will use to send email to Email Address 1/Email Address 2. Email To Email Address 1 Empty Enter your first e-mail address to receive the logs. Email Address 2 Empty Enter your second e-mail address to receive the logs. 3-3-3 FTP You can use FTP (File Transfer Protocol) to upload and download the WAP-001’s firmware and configuration files. To use this feature, your computer must have an FTP client. Figure 17 FTP Setting Screen Item Description Server Port You may change the server port number for a service if needed, however you must use the same port number in order to use FTP to access the WAP-001 Secured Client IP Address A secured client is a “trusted” computer that is allowed to communicate with the WAP-001 using this service. Select All to allow any computer to access the WAP-001 using FTP. Choose Selected to just allow the computer with the IP address

In Wall Box Access Point 28 that you specify to access the WAP-001 using FTP. Apply Choose “Read”, “Write”, “Trap Recipients” and “All” for different privileges. The defaults are all “read”. 3-3-4 SNMP The SNMP Agent Configuration screen enables you to access to your device via Simple Network Management Protocol. If you are not familiar with SNMP, please consult your Network Administrator or consult SNMP reference material. You must first enable SNMP on the SNMP Agent Configuration screen. Figure 18 SNMP Setting Screen Item Default Description SNMP Disable Disables or enables the SNMP management. SNMP Port 161 Trap Port 162 If the SNMP enables, also allowed to specific the SNMP port number via NAT. The allowed SNMP port numbers are 161 (default), 16100-16199 and Trap port numbers are 162 (default), 16200-16299. This Port setting is useful for remote control via NAT network. Configuration Community Name public/private Every unit with SNMP enable must be configured to recognize one or more community names up to 20 characters. The default setting for the community of entry is “public”

In Wall Box Access Point 29 NMS Address ANY The address of the NMS. The default settings for the NMS Networking are “ANY”. Privileges Read Choose “Read”, “Write”, “Trap Recipients” and “All” for different privileges. The defaults are all “read”. Status Valid/Invalid Chosen “Valid” or “Invalid”. The default setting of entry is all invalid. 3-4 System Tool 3-4-1 Configuration This feature can backup the system configuration from this device to your PC or restore your stored system configuration to this device. Figure 19 Configuration Setting Screen Item Default Description Backup Click it to save the system configuration to your computer. (export.cfg) Remote TFTP Server IP Address Empty Enter the IP address of TFTP Server. File Name Empty Enter the file name in the File Name field. Restore Click it to restore your system configuration. Local PC File Path Empty Enter the file pathname of the system configuration file in the

In Wall Box Access Point 30 Local PC File Path field. Remote TFTP Server IP Address Empty Enter the IP address of TFTP Server. File Name Empty Enter the file name in the File Name field. Reset the system back to factory defaults Erase all setting and back to factory setting. 3-4-2 Firmware The Firmware Upgrade menu loads updated firmware to be permanent in flash ROM. The download file should be a binary file from factory; otherwise the agent will not accept it. After downloading the new firmware, the agent will automatically restart it. z Manual Firmware Upgrade Figure 20 Manual Firmware Upgrade Setting Screen Item Default Description This allow administrator to upgrade the firmware via HTTP. Local PC File Path Empty Enter the file name and location in the Local PC File Path field. This allows administrator use TFTP server to upgrade firmware. Remote TFTP Server IP Address Empty Enter the IP address of TFTP Server. File Name Empty Enter the file name in the File Name field. Note: 1. Before downloading the new firmware, users must save the configuration file for restore configuration parameters of the device. 2. Do not turn the power off during the upgrade process. This will damage the unit.

In Wall Box Access Point 31 z Scheduled Firmware Upgrade Scheduled Firmware Upgrade is a program that enables an automatic upgrade to the latest firmware version through the TFTP server. Figure 21 Scheduled Firmware Upgrade Setting Screen Item Default Description Disable/Enable Disables or enables the scheduled firmware upgrade function. TFTP Server IP Empty Enter the IP address of TFTP Server. File Synchronization Empty Enter the file name and location in the File Synchronization field. Click the button to display synchronization file example. Frequency Weekly Set the firmware upgrade time. The default value is “Weekly”. Figure 22 Synchronization File Sample Code Note: Do not turn the power off during the upgrade process. This will damage the unit.

In Wall Box Access Point 32 3-4-3 Ping Command The Ping function can check the Wireless Subscriber Gateway networking connective or not. Figure 23 Ping Command Screen Item Description IP or URL Enter the IP address or the URL link. 3-4-4 Restart If you’re In Wall Box Access Points not operating correctly, you can choose this option to display the restart Wireless Subscriber Gateway screen. Clicking the apply button restart the In Wall Access Point, with all of your settings remaining intact. Figure 24 Restart Screen

In Wall Box Access Point 33 Logout If you would like to leave the configuration page, please click apply to exit. Figure 25 Logout Screen Appendix A Signal Connection Arrangements RJ-45 Ethernet Port The In Wall Box Access PointRJ-45 Ethernet port can connect to any networking devices that use a standard LAN interface, such as a Hub/Switch Hub or Router. Use unshielded twisted-pair (UTP) or shield twisted-pair (STP) cable to connect the networking device to the RJ-45 Ethernet port. Depending on the type of connection, 10Mbps or 100Mbps, use the following Ethernet cable, as prescribed. 10Mbps: Use EIA/TIA-568-100-Category 3, 4 or 5 cables. 100Mbps: Use EIA/TIA-568-100-Category 5 cable. Figure 26 RJ-45 Connector and Cable Pins Note: To prevent loss of signal, make sure that the length of any twisted-pair connection does not exceed 100 meters.

In Wall Box Access Point 34 Appendix B Regulations/EMI Compliance Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: ● Reorient or relocate the receiving antenna. ● Increase the separation between the equipment and receiver. ● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ● Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for Compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. NCC警語: (1)「經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能」警語以及(2)「低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾」警語。

In Wall Box Access Point 35 LIMITED WARRANTY In Wall Box Access Point What the warranty covers: We warrant its products to be free from defects in material and workmanship during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, we will at its sole option repair or replace the product with a like product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components. How long the warranty is effective: The Easy Hotspot Kit is warranted for one year for all parts and one year for all labor from the date of the first consumer purchase. Who the warranty protects: This warranty is valid only for the first consumer purchaser. What the warranty does not cover: 1. Any product, on which the serial number has been defaced, modified or removed. 2. Damage, deterioration or malfunction resulting from: a. Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure to follow instructions supplied with the product. b. Repair or attempted repair by anyone not authorized by us. c. Any damage of the product due to shipment. d. Removal or installation of the product. e. Causes external to the product, such as electric power fluctuations or failure. f. Use of supplies or parts not meeting our specifications. g. Normal wears and tears. h. Any other cause that does not relate to a product defect. 3. Removal, installation, and set-up service charges. How to get service: 1. For information about receiving service under warranty, contact our Customer Support. 2. To obtain warranted service, you will be required to provide (a) the original dated sales slip, (b) your name, (c) your address (d) a description of the problem and (e) the serial number of the product. 3. Take or ship the product prepaid in the original container to your dealer, and our service center. 4. For additional information, contact your dealer or our Customer Service Center. Limitation of implied warranties: THERE ARE NOWARRANTIED, EXPRESSED OR IMPLIED, WHICH EXTEND BEYOND THE DESCRIPTION CONTAINED HEREIN INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Exclusion of damages: Our LIABILITY IS LIMITED TO THE COST OF REPAIR OR REPLACEMENT OF THE PRODUCT. We SHALL NOT BE LIABLE FOR: 1. DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECTS IN THE PRODUCT, DAMAGES BASED UPON INCONVENCE, LOSS OF USE OF THE PRODUCT, LOSS OF TIME, LOSS OF PROFITS, LOSS OF BUSINESS OPPORTUNITY, LOSS OF GOODWILL, INTERFERENCE WITH BUSINESS RELATIONSHIPS, OR OTHER COMMERCIAL LOSS, EVEN IF ADVISED OF THE POSSIBLITY OF SUCH DAMAGES. 2. ANY OTHER DAMAGES, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE. 3. ANY CLAIM AGAINST THE CUSOMER BY ANY OTHER PARTY.

Navigation menu