Hangshi Technology S29 Bluetooth Headset User Manual S29

Shenzhen Hangshi Technology Co., Ltd Bluetooth Headset S29

User Manual

1. Do not disassemble or modify the headphone in any reason.Otherwise headphone can be malfunctioned orburnt.In this case the headphoneis out of warranty coverage. 2. Keep it away from any corrosive liquid.Otherwise it could cause serious damage to headphone.Any damage caused by touching corrosive liquid is not in warranty of manufacturer. 3. Do not use it in thunderstorm weather.Thunderstormcan causeheadphone doesn't work properly and increase the risk of electric shock.4. When pulling out the plug,please be sure to hold Micro USB port cableof headphone.5. Do not overly oppress headphone cable,it may cause interruption or destroy to circuit.6. For the cleanness and hygiene of headphone,please often disassemble silicone earphone tips and use mild detergent to clean.Keey headphone dry and clean when not in use.Please read safety instructions carefully before using.1.Please do not use corrosive liquid to clean headphone. 2.Please keep headphone away from high temperature flame or fire.3.Please avoid headphone falling from a height.4.Please do not let headphone get touch with corrosive liquid. 5.Please do not charge headphone long-time over charging time.6.Please do not disassemble headphone unauthorizedly.To avoid damage to your hearing, please ensure that your music volumeis small when wearing headphone. After wearing well,Please adjust to an appropriate volume.In case of hearing damage,please do not long-time use loud volume to listen to music.Please be responsible for your hearing. Warm reminderModelAudio decodeThe noise reductionBluetooth versionMain control chipsetSupport agreementBluetooth distanceWorking timeCharging timeStandby timeS29APT-XCVC 6.0Bluetooth 4.1CSR 8645HFP/HSP/A2DP/AVRCP≥10M14H1.5-2H≥360HBattery capacitySpeaker unit3.7V , 100mAhx2φ8.2MMWaterproof level IPX4Response frequency 20Hz-20KHzSystem compatibility iOS/Android/WindowsS29 User ManualSpecification Cleaning and maintenance CautionHeadphone introduction Pairing Product list Weraring MethodHeadphoneRightLeft1. Low battery status: Red light flashes every 5 seconds, you will hear “Battery low” voice prompt from the earphone evry 3 minutes;2. Charging status: Red light keeps on.3. Fully charge status: Blue light keeps on.Headphone charging LED indicatorRedial last callingIndicator flashes blue,then flashes red Indicator keeps red for 1 sec,then goes offKey 3 sec.KeyKeyKeyKeyKeyKeyKeyKeyShortShortKeyShort 2 times. 2 times. turns on.DoubleKeyDouble21. Identify the left and right earbuds and ear-fins. earphones.4. Adjust the positioning to get a snug PLEASE NOTE: Using appropriate size maximum external noise isolation and a Pairing with one smartphone·Select S29 from the dvice list, click S29 and wait for a moment;·You will hear “connected” from the earphone after successful connecting.3. Insert the assembled earphones into to your ears like shown in the lower left corner images.the eartips and ear-fins one size at a timeto find the best fit for each side. · Long press Power button on the earphone for 3 seconds , do not lose your finger· You will hear “Power ON” voice prompt from the earphone, keep pressing Power button until you hear “Pairing” voice prompt. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for helpChanges or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Navigation menu