Hangshi Technology S29 Bluetooth Headset User Manual S29
Shenzhen Hangshi Technology Co., Ltd Bluetooth Headset S29
User Manual
1. Do not disassemble or modify the headphone in any reason.Otherwise
headphone can be malfunctioned orburnt.In this case the headphone
is out of warranty coverage.
2. Keep it away from any corrosive liquid.Otherwise it could cause serious
damage to headphone.Any damage caused by touching corrosive liquid
is not in warranty of manufacturer.
3. Do not use it in thunderstorm weather.Thunderstormcan cause
headphone doesn't work properly and increase the risk of electric shock.
4. When pulling out the plug,please be sure to hold Micro USB port cable
of headphone.
5. Do not overly oppress headphone cable,it may cause interruption or
destroy to circuit.
6. For the cleanness and hygiene of headphone,please often disassemble
silicone earphone tips and use mild detergent to clean.Keey headphone
dry and clean when not in use.
Please read safety instructions carefully before using.
1.Please do not use corrosive liquid to clean headphone.
2.Please keep headphone away from high temperature flame or fire.
3.Please avoid headphone falling from a height.
4.Please do not let headphone get touch with corrosive liquid.
5.Please do not charge headphone long-time over charging time.
6.Please do not disassemble headphone unauthorizedly.
To avoid damage to your hearing, please ensure that your music volume
is small when wearing headphone. After wearing well,Please adjust to an
appropriate volume.In case of hearing damage,please do not long-time
use loud volume to listen to music.Please be responsible for your hearing.
Warm reminder
Model
Audio decode
The noise reduction
Bluetooth version
Main control chipset
Support agreement
Bluetooth distance
Working time
Charging time
Standby time
S29
APT-X
CVC 6.0
Bluetooth 4.1
CSR 8645
HFP/HSP/A2DP/AVRCP
≥10M
14H
1.5-2H
≥360H
Battery capacity
Speaker unit
3.7V , 100mAhx2
φ8.2MM
Waterproof level IPX4
Response frequency 20Hz-20KHz
System compatibility iOS/Android/Windows
S29
User Manual
Specification Cleaning and maintenance Caution
Headphone introduction Pairing
Product list Weraring Method
Headphone
Right
Left
1. Low battery status: Red light flashes every 5 seconds, you will hear
“Battery low” voice prompt from the earphone evry 3 minutes;
2. Charging status: Red light keeps on.
3. Fully charge status: Blue light keeps on.
Headphone charging
LED indicator
Redial
last calling
Indicator flashes blue,
then flashes red
Indicator keeps red for 1 sec,
then goes off
Key 3 sec.
Key
Key
Key
Key
Key
Key
Key
KeyShort
Short
Key
Short
2 times.
2 times.
turns on.
Double
Key
Double
2
1. Identify the left and right earbuds and ear-fins.
earphones.
4. Adjust the positioning to get a snug
PLEASE NOTE: Using appropriate size
maximum external noise isolation and a
Pairing with one smartphone
·Select S29 from the dvice list, click S29 and wait for a moment;
·You will hear “connected” from the earphone after successful connecting.
3. Insert the assembled earphones into to your ears like
shown in the lower left corner images.
the eartips and ear-fins one size at a time
to find the best fit for each side.
· Long press Power button on the earphone for 3 seconds ,
do not lose your finger
· You will hear “Power ON” voice prompt from the earphone, keep
pressing Power button until you hear “Pairing” voice prompt.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for
help
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.