Hangzhou Hikvision Digital Technology 25IPC Network Camera User Manual ii

Hangzhou Hikvision Digital Technology Co., Ltd. Network Camera ii

Contents

User Manual ii

Network Bullet CameragQuick Start Guide 22 5. Tear off the protection film softly to complete the installation.  l Do not tear off the protection film until the installation is completed. l Do not touch the inside face of the bubble with your hands.  Wall Mounting 2.4Steps: 1. Install the wall bracket to the wall with the supplied screws in the wall bracket package.  You need to purchases a wall bracket separately if wall mounting is adopted.   Install Wall Bracket Figure 2-122. Fix the adapter plate to the wall bracket.
Network Bullet CameragQuick Start Guide 23   Fix the Adapter Plate Figure 2-133. Fix the dome drive to the wall bracket with the supplied screws.   Install the Camera Figure 2-144. Align the front cover to the dome drive and tighten the set screws on the front cover to complete the installation.
Network Bullet CameragQuick Start Guide 24   Install the Front Cover Figure 2-155. Tear off the protection film softly to complete the installation.  l Do not tear off the protection film until the installation is completed. l Do not touch the inside face of the bubble with your hands.  Install the Micro SD Card 2.5This series of camera supports local storage, please refer to the following steps to install the micro SD card. Steps: 1. Remove the front cover by loosening the set screws on it.
Network Bullet CameragQuick Start Guide 25   Remove the Front Cover Figure 2-162. Insert the micro SD card to the card slot until you hear a click. 3. (Optional)Slightly push the inserted micro SD card to uninstall it from the camera.  Figure 2-17 Install and Uninstall Micro SD Card Mirco SD Card
Network Bullet CameragQuick Start Guide 26 3 Setting the Network Camera over the LAN Note: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, please contact with your dealer or the nearest service center.  Wiring 3.1Please connect to the camera to the network according to the following figures   Connecting Directly Figure 3-1  Connecting via a Switch or a Router Figure 3-2
Network Bullet CameragQuick Start Guide 27  Activating the Camera 3.2You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported. We will take activation via SADP software and Activation via Web Browser as examples to introduce the camera activation. Please refer to the User Manual of Network Camera for Activation via Client Software.    Activation via Web Browser 3.2.1Steps: 1. Power on the camera, and connect the camera to the network. 2. Input the IP address into the address bar of the web browser, and click Enter to enter the activation interface. Notes: l The default IP address of the camera is 192.168.1.64.   l For the camera enables the DHCP by default, you need to activate the camera via SADP software and search the IP address.
Network Bullet CameragQuick Start Guide 28   Activation Interface(Web) Figure 3-33. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product. 4. Confirm the password. 5. Click OK to save the password and enter the live view interface.
Network Bullet CameragQuick Start Guide 29  Activation via SADP Software 3.2.2SADP software is used for detecting the online device, activating the camera, and resetting the password.   Get the SADP software from the supplied disk or the official website, and install the SADP according to the prompts. Follow the steps to activate the camera, please refer to the User Manual of Network Camera for other two activation methods. Steps: 1. Run the SADP software to search the online devices. 2. Check the device status from the device list, and select the inactive device.   SADP Interface Figure 3-4Note: The SADP software supports activating the camera in batch. Please refer to the user manual of SADP software for details.
Network Bullet CameragQuick Start Guide 30 3. Create a password and input the password in the password field, and confirm the password. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product. 4. Click OK to save the password. You can check whether the activation is completed on the popup window. If activation failed, please make sure that the password meets the requirement and try again.    Modifying the IP Address 3.3Purpose: To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet with your PC. Then, install the SADP software or client software to search and change the IP of network camera. We will take modifying the IP Address via SADP software as an example to introduce the IP address modification. Steps: 1. Run the SADP software. 2. Select an active device.
Network Bullet CameragQuick Start Guide 31 Note: Please refer to Chapter 3.2 to activate the camera if the camera is inactive.   3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP.   Modify the IP Address Figure 3-54. Input the password to activate your IP address modification. The batch IP address modification is supported by the SADP; please refer to the User Manual of SADP for details.
Network Bullet CameragQuick Start Guide 32 4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version   CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.0 and above version and Google Chrome 18 and above version Steps: 1. Open the web browser. 2. In the browser address bar, input the IP address of the network camera, and press the Enter key to enter the login interface. Note: l The default IP address is 192.168.1.64. l If the camera is not activated, please activate the camera first according to Chapter 3.2. 3. Input the user name and password. The admin user should configure the device accounts and user/operator permissions properly. Delete the unnecessary accounts and user/operator permissions. Note: The device IP address gets locked if the admin user performs 7 failed password attempts (5 attempts for the user/operator).
Network Bullet CameragQuick Start Guide 33 4. Click Login.   Login Interface Figure 4-15. Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in.  You may have to close the web browser to finish the installation of the plug-in.
Network Bullet CameragQuick Start Guide 34   Download Plug-in Figure 4-2  Install Plug-in (1) Figure 4-3
Network Bullet CameragQuick Start Guide 35   Install Plug-in (2) Figure 4-46. Reopen the web browser after the installation of the plug-in and repeat steps 2~4 to login.  For detailed instructions of further configuration, please refer to the user manual of network camera.

Navigation menu