Hangzhou Tuya Information Technology TYWE2S Wi-Fi Module User Manual TYWE2S V1 02 ENx
Hangzhou AiXiangJi Technology Co., Ltd Wi-Fi Module TYWE2S V1 02 ENx
Users Manual
TYWE2S DATASHEET TYWE2S UserManual 1. Product Overview TYWE2S is a low power consumptionmodulewithbuilt-in Wi-Fi connectivity solution designed by Hangzhou AiXiangJi Technology Co., Ltd.The Wi-Fi Module consistsof a highly integratedwireless radio chip ESP8285 andsome extra componentthathas been programed with Wi-Fi network protocol and plenty of software examples.TYWE2Sincludea 32-bit CPU, 1M byte flash, 50kB SRAM and various peripheral resources. TYWE2S is a RTOS platform, embedded with all the Wi-Fi MAC and TCP/IP protocol function examples, users can customize their Wi-Fi product by using these software examples. Figure 1 shows the block diagramof the TYWE2S. Figure 1. The block diagram of the TYWE2S 1.1 Features Integrated low power consumption 32-bit CPU, also known as application processor Basic frequency of the CPU can support both 80MHz and 160MHz Supply voltage range: 3V to 3.6V Peripherals: 5 GPIO channels, 1 UART, 1 ADC Wi-Fi connectivity: 802.11 b/g/n20 Channel 1 to 11 @ 2.4GHz Support WPA/WPA2 +16dBm output power Support STA/AP/STA+AP operation mode Support SmartConfig function for both Android and IOS devices On-board PCB antenna TYWE2S DATASHEET Operating temperature range: -20℃ to 85℃ 1.2 Main ApplicationFields Intelligent Building Intelligent home, Intelligent household applications Health care Industrial wireless control Baby monitor Webcam Intelligent bus TYWE2S DATASHEET 2. Dimensions and Footprint 2.1Dimensions TYWE2S has 2 columns of Pins.The distance between each Pin is 2mm. Size of TYWE2S: 15mm (L) ×17.3mm (W) × 2.8 mm (H) Figure 2 shows the dimensions of TYWE2S. Figure 2. The dimensions of TYWE2S 2.2 Pin Definition Table 1 shows the generalpin attributes of TYWE2S Table 1. The typical pin definitionof TYWE2S PIN NO. NAME TYPE DISCREPTION RST I/O External reset (low level effects, there's already had pull‐up resistor) AD AI ADC terminal(10‐bits SAR ADC)(1) 13 I/O GPIO_13 04 I/O GPIO_04 05 I/O GPIO_05 3V3 Supply voltage (3.3V) GND Ground RX I/O UART0_RXD TX I/O 10 12 I/O UART0_TXD GPIO_12 11 14 I/O GPIO_14 (2) (2) Note: S: Power supply pins; I/O: Digital input or output pins; AI: Analog input.RST pin is the module hardware reset pin; it cannot eliminate module-pairing information. TYWE2S DATASHEET (*1) This pin can only be used as ADC input, cannot use it as normal I/O. when not using, just connect nothing. When used as ADC input, the input voltage range is 0~1.0V. (*2) UART0 is serial port, during power on progress; this serial port will output something, which can be ignored. 2.3Test PinDefinition Table 2 shows the general test pin definition of TYWE2S Table 2. The generaltest pin definitionof TYWE2S PIN NO Name IO Type Function 12 IO4 I/O GPIO_04 13 IO13 I/O GPIO_13 14 IO2 I/O UART1_TXD 15 RST I/O Reset Pin 16 IO5 I/O GPIO_05 17 IO0 I/O IO0 TYWE2S DATASHEET 3. Electrical Characteristics 3.1 Absolute Maximum Ratings Table 3. Absolute Maximum Ratings PARAMETERS DESCRIPTION MIN MAX UNIT Ts Storage temperature ‐20 85 ℃ VCC Supply voltage ‐0.3 3.6 Static electricity voltage (human model) TAMB‐25℃ ‐ KV Static electricity voltage (machine model) TAMB‐25℃ ‐ 0.5 KV 3.2 Electrical Conditions Table 4. Electrical Conditions PARAMETERS DESCRIPTION MIN TYPICAL MAX UNIT Ta Working temperature ‐20 ‐ 85 ℃ VCC Working voltage 3.3 3.6 VIL IO low level input ‐0.3 ‐ VCC*0.25 VIH IO high level input VCC*0.75 ‐ VCC VOL IO low level output ‐ ‐ VCC*0.1 VoH IO high level output VCC*0.8 ‐ VCC Imax IO drive current ‐ ‐ 12 mA 3.3 Wi-Fi Transmitting Current Consumptions Table 5. Wi-Fi TX current consumption PARAMETERS MODE RATE transmitting power TYPICAL UNIT IRF 11b 1Mbps 16dBm 220 mA IRF 11g 6Mbps 21dBm 110 mA IRF 11n MCS0 21.5dBm 100 mA 3.4 Wi-Fi Receiving CurrentConsumptions Table 6. Wi-Fi RX currentconsumption PARAMETERS MODE RATE TYPICAL UNIT IRF 11b 1Mbps 76 mA IRF 11g 6Mbps 76 mA IRF 11n MCS0 76 mA TYWE2S DATASHEET 3.5 Working Mode CurrentConsumptions Table 7. The module working currentconsumption WORK MODE AT TA=25℃ TYPICAL MAX* UNIT EZ Mode TYWE2S is under EZ paring mode, Wi‐Fi indicator light flashes quickly 80 151 mA AP Mode TYWE2S is under AP paring mode, Wi‐Fi indicator light flashes slowly 90 451 mA Operation Mode TYWE2S is connected, Wi‐Fi indicator light is on 58.5 411 mA Disconnection Mode TYWE2S is disconnected, Wi‐Fi indicator light is off 80 430 mA 4. WLAN Radio Specification 4.1 Basic Radio Frequency Characteristics Table 8.Basic Radio frequency characteristics PARAMETERS DESCRIPTION Frequency band 2.4GHz to 2.5GHz Wi‐Fi standard IEEE 802.11n/g/b 11b:1,2,5.5,11(Mbps) Data transmitting rate 11g:6,9,12,18,24,36,48,54(Mbps) 11n:HT20,MCS0~7 Antenna type On‐board PCB Antenna 4.2Wi-Fi TransmittingPower Table 9. Wi-Fi transmitting power PARAMETERS MIN TYPICAL MAX UNI RF average output power, 802.11b CCK Mode 1M ‐ 16 ‐ dBm RF average output power, 802.11g OFDM Mode 6M ‐ 21 ‐ dBm RF average output power, 802.11n OFDM Mode MCS0 ‐ 21.5 ‐ dBm ‐10 ‐ 10 ppm MAX UNI The Frequency error 4.3Wi-Fi Receiving Sensitivity Table 9. Wi-Fi Receiving sensitivity PARAMETERS MIN TYPICAL TYWE2S DATASHEET PER<8%, Receiving sensitivity, 802.11b CCK Mode 1M ‐ ‐91 ‐ dBm PER<10%, Receiving sensitivity, 802.11g OFDM Mode 6M ‐ ‐75 ‐ dBm PER<10%, Receiving sensitivity, 802.11n OFDM Mode MCS0 ‐ ‐72 ‐ dBm TYWE2S DATASHEET 5. Antenna Information 5.1 Antenna Type Antenna can be connected only using On-board PCB antenna. 5.2 Reduce Antenna Interference While using the On-board PCBantenna, in order to have the best Wi-Fi performance, it’s recommended to keep a minimum15mm distance between the antenna part and the other metal pieces. User’s own PCBA design is recommended NOT to pass any wire, NOT do copper pour under the region of the module’s antenna, to avoid interferences. TYWE2S DATASHEET 6. Packaging Information And Production Guide 6.1 Mechanical Dimensions Figure 3. Top view of the module Figure 4. The module’s mechanical view 6.2PCBRecommended Package Figure 5. PCB schematic Drawing TYWE2S DATASHEET Figure 6. PCB Package Drawing 6.3 Production Guide The storage for the delivered module should meet the following condition: 1. The anti-moisture bag should be kept in the environment withtemperature< 30℃ and humidity< 85% RH. 2. The expiration date is 6 months since the dry packaging products was sealed. Cautions: 1. All the operators should wear electrostatic ringin the whole process of production. 2. While operating, water and dirt should not have any contact with the modules. 6.4 Recommended furnace temperature curve Figure 7. PCB Package DrawingRecommended furnace temperature curve TYWE2S DATASHEET FCC Waring $Q\&KDQJHVRUPRGLILFDWLRQVQRWH[SUHVVO\DSSURYHGE\WKHSDUW\UHVSRQVLEOHIRUFRPSOLDQFHFRXOG YRLGWKHXVHU¶VDXWKRULW\WRRSHUDWHWKHHTXLSPHQW This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference (2) this device must accept any interference received, including interference that may cause undesired operation. )&&5DGLDWLRQ([SRVXUH6WDWHPHQW This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. FCC/ISED Label Instructions The outside of final products that contains this module device must display a label referring to the enclosed module. This exterior label can use wording such as: "Contains Transmitter Module FCC ID:2ANDL-TYWE2S or IC:23243-TYWE2S"or “Contains FCC ID:2ANDL-TYWE2S or IC:23243-TYWE2S", Any similar wording that expresses the same meaning may be used. ISED RSS Warning: This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. ISED5DGLDWLRQ([SRVXUH6WDWHPHQW This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment .This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Le rayonnement de la classe b repecte ISED fixaient un environnement non contrôlés.Installation et mise en œuvre de ce matériel devrait avec échangeur distance minimale entre 20 cm ton corps.Lanceurs ou ne peuvent pas coexister cette antenne ou capteurs avec d’autres.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Author : baclsh93 Create Date : 2017:09:19 11:29:39+08:00 Modify Date : 2017:10:09 17:12:37-07:00 Has XFA : No XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Creator Tool : PScript5.dll Version 5.2.2 Metadata Date : 2017:10:09 17:12:37-07:00 Format : application/pdf Title : Microsoft Word - TYWE2S_V1.02_EN.docx Creator : baclsh93 Producer : Acrobat Distiller 11.0 (Windows) Document ID : uuid:183c9388-9fd3-447f-a75b-54083c5d6436 Instance ID : uuid:acb8ab4a-9b81-4664-a8b6-bd17480022b6 Page Count : 11EXIF Metadata provided by EXIF.tools