Hangzhou Tuya Information Technology TYWE3L Wi-Fi Module User Manual TYWE3L V1 00 ENx
Hangzhou Tuya Information Technology Co.,Ltd Wi-Fi Module TYWE3L V1 00 ENx
TYWE3L DATASHEET Wi-Fi Module UserManual 1. Product Overview TYWE3L is a low power consumption module with built-in Wi-Fi connectivity solution designed by HangZhouTuya Information Technology Corporation. The Wi-Fi Module consists of a highly integrated wireless radio chip ESP8266 and some extra component that has been programed with Wi-Fi network protocol and plenty of software examples.TYWE3L include a 32bit CPU, 1M byte flash, 50k SRAM and various peripheral resources. TYWE3L is a RTOS platform, embedded with all the Wi-Fi MAC and TCP/IP protocol function examples, users can customize their Wi-Fi product by using these software examples. Figure 1 shows the block diagram of the TYWE3L. Figure 1. The block diagram of the TYWE3L 1.1 Features Integrated low power consumption 32-bit CPU, also known as application processor Basic frequency of the CPU can support 160MHz Supply voltage range: 3V to 3.6V Peripherals: 9 GPIO channels, 1 UART, 1 ADC Wi-Fi connectivity: 802.11 b/g/n channel 1 to email@example.comG for FCC Support WPA/WPA2 +20.22dBm output power in 802.11b mode Support STA/AP/STA+AP operation mode Support SmartConfig function for both Android and IOS devices On-board PCB antenna TYWE3L DATASHEET Operating temperature range: -20℃ to 105℃ 1.2 Main ApplicationFields Intelligent Building Intelligent home, Intelligent household applications Health care Industrial wireless control Baby monitor Webcam Intelligent bus 2. Dimensions and Footprint 2.1Dimensions TYWE3L has 2 columns of Pins.The distance between each Pin is 2mm. Size of TYWE3L: 16mm(W)*24mm(L)*3.5mm(H) Figure 2 shows the dimensions of TYWE3L. Figure 2. The dimensions of TYWE3L 2.2 Pin Definition Table 1 shows the generalpin attributes of TYWE3L RST TXD ADC RXD EN IO5 IO16 IO4 IO14 IO0 IO12 IO2 IO13 IO15 VCC GND TYWE3L DATASHEET Table 1. The typical pin definitionof TYWE3L PIN NO. NAME RST TYP I/O ADC AI GPIO12 GPIO13 VCC GND 10 GPIO15 11 GPIO2 12 13 14 15 16 GPIO_14 GPIO_12 GPIO_13 Supply voltage (3.3V) I/O Ground I/O GPIO_15(processing during initials, caution when used) I/O GPIO0 I/O RXD0 AI GPIO4 GPIO5 GPIO_16（10k pull-up resistor needed) I/O I/O GPIO14 ADC terminal(10-bits SAR ADC)(1) Enable pin for module, high level effects I/O GPIO16 External reset (low level effects, there's already had pull-up resistor) EN DISCREPTION UART0_TXD(used to print module's internal information) GPIO_0(processing during initials, caution when used) GPIO_04 GPIO_05 I/O TXD0 UART0_RXD (2) UART0_TXD (2) I/O Note: S: Power supply pins; I/O: Digital input or output pins; AI: Analog input.RST pin is the module hardware reset pin; it cannot eliminate module-pairing information. (*1) This pin can only be used as ADC input, cannot use it as normal I/O. when not using, just connect nothing. When used as ADC input, the input voltage range is 0~1.0V. (*2) UART0 is serial port, during power on progress; this serial port will output something, which can be ignored. 2.3Test PinDefinition Table 2 shows the generaltest pindefinition of TYWE3L Table 2. The generaltest pindefinitionof TYWE3L PIN NO. NAME TYPE DESCRIPTION TEST Used for module’s production test Note: This test pin is not recommended to use. TYWE3L DATASHEET 3. Electrical Characteristics 3.1 Absolute Maximum Ratings Table 3. Absolute Maximum Ratings PARAMETERS DESCRIPTION MIN MAX UNIT Ts Storage temperature -20 105 VCC Supply voltage -0.3 3.6 ℃ Static electricity voltage (human model) TAMB-25℃ KV Static electricity voltage (machine model) TAMB-25℃ 0.5 KV 3.2 Electrical Conditions Table 4. Electrical Conditions PARAMETERS DESCRIPTION MIN TYPICAL MAX UNIT Ta Working temperature -20 105 VCC Working voltage 3.3 3.6 ℃ VIL IO low level input -0.3 VCC*0.25 VIH IO high level input VCC*0.75 VCC VOL IO low level output VCC*0.1 VoH IO high level output VCC*0.8 VCC Imax IO drive current 12 mA 3.3 Wi-Fi Transmitting Current Consumptions Table 5. Wi-Fi TX current consumption PARAMETERS MODE RATE IRF 11b 1Mbps IRF 11g IRF 11n transmitting power TYPICAL UNIT + 20.22dBm 220 mA 6Mbps +23.00dBm 110 mA MCS0 +22.74dBm 100 mA 3.4 Wi-Fi Receiving CurrentConsumptions Table 6. Wi-Fi RX currentconsumption PARAMETERS MODE RATE TYPICAL UNIT IRF 11b 1Mbps 76 mA IRF 11g 6Mbps 76 mA IRF 11n MCS0 76 mA TYWE3L DATASHEET 3.5 Working Mode CurrentConsumptions Table 7. The module working currentconsumption WORK MODE AT TA=25℃ TYPICAL MAX* UNIT EZ Mode TYWE3L is under EZ paring mode, Wi-Fi indicator light flashes quickly 80 151 mA AP Mode TYWE3L is under AP paring mode, Wi-Fi indicator light flashes slowly 90 451 mA Operation Mode TYWE3L is connected, Wi-Fi indicator light is on 58.5 411 mA Disconnection Mode TYWE3L is disconnected, Wi-Fi indicator light is off 80 430 mA 4. WLAN Radio Specification 4.1 Basic Radio Frequency Characteristics Table 8.Basic Radio frequency characteristics PARAMETERS DESCRIPTION Frequency band 2.412GHz to 2.462GHz Wi-Fi standard IEEE 802.11n/g/b (Terminal 1-11) Data transmitting rate 11b:1,2,5.5,11(Mbps) 11g:6,9,12,18,24,36,48,54(Mbps) 11n:HT20,MCS0~7 Antenna type On-board PCB Antenna 4.2Wi-Fi TransmittingPower Table 9. Wi-Fi transmitting power PARAMETERS MIN TYPICAL MAX UNI RF average output power, 802.11b CCK Mode 1M 20.22 dBm RF average output power, 802.11g OFDM Mode 6M 23.00 dBm RF average output power, 802.11n OFDM Mode MCS0 22.74 dBm 10 ppm MAX UNI The Frequency error -10 4.3Wi-Fi Receiving Sensitivity Table 9. Wi-Fi Receiving sensitivity PARAMETERS MIN TYPICAL TYWE3L DATASHEET PER<8%, Receiving sensitivity, 802.11b CCK Mode 1M -91 dBm PER<10%, Receiving sensitivity, 802.11g OFDM Mode 6M -75 dBm PER<10%, Receiving sensitivity, 802.11n OFDM Mode MCS0 -72 dBm TYWE3L DATASHEET 5. Antenna Information 5.1 Antenna Type Antenna can be connected only using On-board PCB antenna. 5.2 Reduce Antenna Interference While using the On-board PCBantenna, in order to have the best Wi-Fi performance, it’s recommended to keep a minimum15mm distance between the antenna part and the other metal pieces. User’s own PCBA design is recommended NOT to pass any wire, NOT do copper pour under the region of the module’s antenna, to avoid interferences. TYWE3L DATASHEET 6. Packaging Information And Production Guide 6.1 Mechanical Dimensions Figure 3. Top view of the module Figure 4. The module’s mechanical view TYWE3L DATASHEET 6.2PCBRecommended Package Figure 5. PCB schematic Drawing Figure 6. PCB Package Drawing 6.3 Production Guide The storage for the delivered module should meet the following condition: 1. The anti-moisture bag should be kept in the environment withtemperature< 30℃ and humidity< 85% RH. 2. The expiration date is 6 months since the dry packaging products was sealed. Cautions: 1. All the operators should wear electrostatic ringin the whole process of production. 2. While operating, water and dirt should not have any contact with the modules. TYWE3L DATASHEET 6.4 Recommended furnace temperature curve Figure 7. PCB Package DrawingRecommended furnace temperature curve FCC Statement Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. FCC Label Instructions The outside of final products that contains this module device must display a label referring to the enclosed module. This exterior label can use wording such as: “Contains Transmitter Module FCC ID:2ANDL-TYWE3L”,or “Contains FCC ID:2ANDL-TYWE3L”, Any similar wording that expresses the same meaning may be used.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : No Author : 35003 Create Date : 2018:06:03 07:08:38+08:00 Modify Date : 2018:06:19 17:35:34-07:00 Has XFA : No XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Format : application/pdf Creator : 35003 Title : Microsoft Word - TYWE3L_V1.00_EN.docx Metadata Date : 2018:06:19 17:35:34-07:00 Producer : Microsoft: Print To PDF Document ID : uuid:cec9e420-3c2e-4975-8916-d32c56687a1c Instance ID : uuid:a137ef63-0522-41a7-b92b-f743019c2f21 Page Count : 10EXIF Metadata provided by EXIF.tools