Hangzhou Tuya Information Technology TYZS1 Tuya Zigbee Module User Manual TYZS1 EN Datasheet V1 0 0
Hangzhou Tuya Information Technology Co.,Ltd Tuya Zigbee Module TYZS1 EN Datasheet V1 0 0
User Manual
TYZS1 DATASHEET Tuya Zigbee Module 1. Product Overview TYZS1 is a low power consumption module with built-in Zigbee connectivity solution designed by Hangzhou Tuya Information Technology Co., Ltd. The Zigbee Module consists of a highly integrated wireless radio chip EFR32MG1B132 and some extra component that has been programed with Zigbee network protocol 802.15.4 PHY/MAC and plenty of software examples. TYZS1 include a 32-bit ARM Cortex-M4 CPU, 256K byte flash, 32k SRAM and various peripheral resources. TYZS1 is a FreeRTOS platform, embedded with all the Zigbee MAC and TCP/IP protocol function examples, users can customize their Zigbee product by using these software examples. Figure 1 shows the block diagram of the TYZS1. Figure 1. The block diagram of the TYZS1 1.1 Features Integrated low power consumption 32-bit ARM Cortex-M4 CPU, with DSP command and float computing unit also using for application processor Basic frequency of the CPU can support 40MHz Supply voltage : DC3.3V Peripherals: 9 GPIO channels, 1 UART, 1 ADC Zigbee connectivity: 802.15.4 MAC/PHY Channel 11 to 26 @ 2.405-2.480 GHz, radio rate 250 kbps Embedded DC-DC circuit, maximally improving power efficiency +9.56dBm output power 1.4uA standby current at 63uA/MHz Automatic paring for terminals On-board PCB antenna Operating temperature range: -40℃ to 85℃ Hardware encryption, AES 128/256 TYZS1 DATASHEET 1.2 Main Application Fields Intelligent Building Intelligent home, Intelligent household applications Smart socket, smart lighting Industrial wireless control Health and measurement management Asset trace TYZS1 DATASHEET 2. Dimensions and Footprint 2.1 Dimensions TYZS1 has 2 columns of Pins. The distance between each Pin is 2mm. Size of TYZS1: 16mm(W)*24mm(L)*3.5mm(H) Figure 2 shows the dimensions of TYZS1. Figure 2. The dimensions of TYZS1 2.2 Pin Definition Table 1 shows the general pin attributes of TYZS1 Table 1. The typical pin definition of TYZS1 PIN NO. NAME TYP DISCREPTION nRST hardware reset pin, low level effects; the module will reset while booting, user could ignore the pin just in case ADC AI ADC terminal(12‐bits SAR ADC) (1) NC ‐ NC GPIO0 I/O GPIO0 SWO I/O also used for universal GPIO, can be used for output pin while in JLINK communication status PWM3 I/O also used for universal GPIO PWM1 I/O also used for universal GPIO VCC Supply voltage (3.3V) GND Ground 10 GPIO2 I/O also used for universal GPIO 11 SWDIO I/O JLINK SWDIO burning pin, also used for universal GPIO TYZS1 DATASHEET 12 SWCLK I/O JLINK SWCLK burning pin, also used for universal GPIO 13 PWM2 I/O also used for universal GPIO 14 GPIO3 I/O also used for universal GPIO 15 RXD I/O UART0_RXD 16 TXD UART0_TXD Note: S: Power supply pins; I/O: Digital input or output pins; AI: Analog input. RST pin is the module hardware reset pin; it cannot eliminate Zigbee module pairing information. (1) This pin can only be used as ADC input, cannot use it as normal I/O. when not using, just connect nothing. When used as ADC input, the input voltage range is 0~AVDD, can be configured by firmware. 2.3 Test Pin Definition Table 2 shows the general test pin definition of TYZS1 Table 2. The general test pin definition of TYZS1 PIN NO. SYMBOL TYPE DESCRIPTION ‐ ‐ Used for module’s production test Note: This test pin is not recommended to use. TYZS1 DATASHEET 3. Electrical Characteristics 3.1 Absolute Maximum Ratings Table 3. Absolute Maximum Ratings PARAMETERS DESCRIPTION MIN MAX UNIT Ts Storage temperature ‐50 150 ℃ VCC Supply voltage 3.0 3.8 Static electricity voltage (human model) TAMB‐25℃ ‐ 2.5 KV Static electricity voltage (machine model) TAMB‐25℃ ‐ 0.5 KV 3.2 Electrical Conditions Table 4. Electrical Conditions PARAMETERS DESCRIPTION MIN TYPICAL MAX UNIT Ta Working temperature ‐40 ‐ 85 ℃ VCC Working voltage 3.0 3.3 3.8 VIL IO low level input ‐0.3 ‐ VCC*0.25 VIH IO high level input VCC*0.75 ‐ VCC VOL IO low level output ‐ ‐ VCC*0.1 VoH IO high level output VCC*0.8 ‐ VCC Imax IO drive current ‐ ‐ 12 mA 3.3 Zigbee Transmitting Current Consumptions Table 5. Zigbee TX current consumption PARAMETERS RATE IRF 250kbps IRF IRF Transmitting power TYPICAL UNIT +9.56dBm 32 mA 250kbps +9.55dBm 17 mA 250kbps +7.10dBm 11.8 mA Note: continuously transmitting data while testing the result shown above, duty cycle=100% 3.4 Zigbee Receiving Current Consumptions Table 6. Zigbee RX current consumption PARAMETERS RATE TYPICAL UNIT IRF 250kbps mA Note: Receiving current 14mA while in active mode. TYZS1 DATASHEET 3.5 Working Mode Current Consumptions Table 7. The module working current consumption WORK MODE AT TA=25℃ TYPICAL MAX* UNIT Quick pairing Mode TYZS1 is under quick paring mode with Gateway. 10 40 mA Connection Mode TYZS1 is connected 0.005 mA Deep sleep Mode TYZS1 is in deep sleep mode, reserving 64KB flash 1.4 uA 4. WLAN Radio Specification 4.1 Basic Radio Frequency Characteristics Table 8. Basic Radio frequency characteristics PARAMETERS DESCRIPTION Frequency band 2.405GHz to 2.480GHz Zigbee standard IEEE 802.15.4 Data transmitting rate 250kbps Antenna type On‐board PCB Antenna >120m Visible transmitting distance 4.2 Zigbee Transmitting Power Table 9. Zigbee transmitting power PARAMETERS MIN Maximum output power ‐ Minimum output power ‐ Output power adjust step The Frequency error Output frequency adjacent channel suppression TYPICAL MAX UNI +9.56 ‐ dBm ‐ dBm ‐ +7.10 0.5 ‐15 ‐ +15 ppm ‐31 dB dBc Note: If more coverage expansion needed, it’s recommended to use TYZS3 module, the module has pin definition compatible with TYZS1 but with higher penetration performance. 4.3 Zigbee Receiving Sensitivity Table 9. Zigbee Receiving sensitivity TYZS1 DATASHEET PARAMETERS MIN TYPICAL MAX UNIT PER<10%, Receiving sensitivity, 250kbps @ OQPSK ‐ ‐102 ‐ dBm TYZS1 DATASHEET 5. Antenna Information 5.1 Antenna Type Antenna default connected using On-board PCB antenna 5.2 Reduce Antenna Interference While using the On-board PCB antenna, in order to have the best Zigbee performance, it’s recommended to keep a minimum 15mm distance between the antenna part and the other metal pieces. User’s own PCBA design is recommended NOT to pass any wire, NOT do copper pour under the region of the module’s antenna, to avoid interferences. TYZS1 DATASHEET 6. Packaging Information And Production Guide 6.1 Mechanical Dimensions Figure 3. Top view of the module Figure 4. The module’s mechanical view 6.2 PCB Recommended Package TYZS1 DATASHEET Figure 5. PCB Package Drawing TYZS1 DATASHEET 6.3 Production Guide The storage for the delivered module should meet the following condition: 1. The anti-moisture bag should be kept in the environment with temperature < 30℃ and humidity < 85% RH. 2. The expiration date is 6 months since the dry packaging products was sealed. Cautions: 1. All the operators should wear electrostatic ring in the whole process of production. 2. While operating, water and dirt should not have any contact with the modules. 6.4 Recommended furnace temperature curve Figure 6. PCB Package Drawing Recommended furnace temperature curve FCC Statement: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. FCC Label Instructions: The outside of final products that contains this module device must display a label referring to the enclosed module. This exterior label can use wording such as: “Contains Transmitter Module FCC ID:2ANDL-TYZS1”,or “Contains FCC ID:2ANDL-TYZS1”, Any similar wording that expresses the same meaning may be used.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Author : baclsh47 Create Date : 2018:07:16 09:01:52+08:00 Modify Date : 2018:07:31 13:55:35-07:00 Has XFA : No XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Format : application/pdf Title : Microsoft Word - TYZS1_EN_Datasheet_V1.0.0 Creator : baclsh47 Creator Tool : PScript5.dll Version 5.2.2 Metadata Date : 2018:07:31 13:55:35-07:00 Producer : Acrobat Distiller 9.0.0 (Windows) Document ID : uuid:61ce84c4-5132-4667-a5c4-1a37ac3ce24d Instance ID : uuid:83a78d51-12f2-4dc8-9c56-42a4a425745f Page Count : 11EXIF Metadata provided by EXIF.tools