Hangzhou Tuya Information Technology WR1 Wi-Fi Module User Manual WR1 x

Hangzhou Tuya Information Technology Co.,Ltd Wi-Fi Module WR1 x

User Manual

Download: Hangzhou Tuya Information Technology WR1 Wi-Fi Module User Manual WR1 x
Mirror Download [FCC.gov]Hangzhou Tuya Information Technology WR1 Wi-Fi Module User Manual WR1 x
Document ID3943607
Application IDFs3vrK+wypLPcTZ6vtiRCA==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize40.02kB (500291 bits)
Date Submitted2018-07-30 00:00:00
Date Available2018-07-30 00:00:00
Creation Date2018-07-17 14:45:48
Producing SoftwareAcrobat Distiller 11.0 (Windows)
Document Lastmod2018-07-30 11:24:50
Document TitleMicrosoft Word - WR1_User manual.docx
Document CreatorPScript5.dll Version 5.2.2
Document Author: baclks150

WR1 DATASHEET
Tuya SmartWi-Fi Module
1. Product Overview
WR1 is a low power consumption module with built-in Wi-Fi connectivity solution designed
by Hangzhou Tuya Information Technology Co., Ltd. The Wi-Fi Module consists of a highly
integrated wireless radio chip W302 12E75M2 and some extra flash that has been programed
with Wi-Fi network protocol and plenty of software examples.WR1 include a ARM CM4F,
WLAN MAC, 1T1R WLAN, maximum frequency reaches 125MHz, 256K SRAM, 1M byte
flash and various peripheral resources.
WR1 is a RTOS platform, embedded with all the Wi-Fi MAC and TCP/IP protocol function
examples, users can customize their Wi-Fi product by using these software examples.
Figure 1 shows the block diagram of the WR1.
Figure 1. The block diagram of the WR1
1.1 Features





Integrated low power consumption 32-bit CPU, also known as application processor
Basic frequency of the CPU can support 125 MHz
Supply voltage range: 3V to 3.6V
Peripherals: 6 GPIO channels, 2 UART, 1 ADC
Wi-Fi connectivity:
 802.11 B/G/N20/N40
 Channel 1 to 11 @ 2.4GHz
 Support WPA/WPA2
 +21.10dBm output power in 802.11b mode
WR1 DATASHEET



Support SmartConfig function for both Android and IOS devices
On-board PCB antenna
Operating temperature range: -20℃ to 105℃
1.2 Main Application Fields







Intelligent Building
Intelligent home, Intelligent household applications
Healthy devices
Industrial wireless control
Baby monitor
Webcam
Intelligent bus
WR1 DATASHEET
2. Dimensions and Footprint
2.1Dimensions
WR1 has 2 columns of Pins (2*9).The distance between each Pin is 1.5 mm.
Size of WR1: 18mm(W)*23.5mm(L)*3.1mm(H)
Figure 2 shows the dimensions of WR1.
Figure 2. The dimensions of WR1
2.2 Pin Definition
Table 1 shows the generalpin attributes of WR1
Table 1. The typical pin definition of WR1
PIN
NO.
NAME
TYP
DISCREPTION
VCC
Supply voltage (3.3V)
UART0_TX
I/O
UART0_TXD
UART0_RX
I/O
UART0_RXD
VD33
Supply voltage (3.3V)
GND
Ground
GPIOA_14
I/O
GPIOA_14
GPIOA_15
I/O
GPIOA_15
WR1 DATASHEET
LOG_TXD
I/O
UART_Log_TXD(used to print module's internal information)
GPIOA_0
I/O
GPIOA_0, can not be pull‐up while booting, can be used as GPIO
while in normal working mode
10
GPIOA_5
I/O
GPIOA_5
11
LOG_RXD
I/O
UART_Log_RXD (used to print module's internal information)
12
GPIOA_19
I/O
GPIOA_19
13
GPIOA_22
I/O
GPIOA_22
14
GND
Ground
15
GND
Ground
16
CHIP_EN
I/O
External reset singal(low level effects)
17
ADC
AI
ADC terminal(input 5V maximally)
18
GND
Ground
Note: S: Power supply pins; I/O: Digital input or output pins; AI: Analog input.
WR1 DATASHEET
3. Electrical Characteristics
3.1 Absolute Maximum Ratings
Table 3.1. Absolute Maximum Ratings
PARAMETERS
DESCRIPTION
MIN
MAX
UNIT
Ts
Storage temperature
‐20
105
℃
VCC
Supply voltage
‐0.3
3.6
Static electricity voltage
(human model)
TAMB‐25℃
‐
KV
Static electricity voltage
(machine model)
TAMB‐25℃
‐
0.5
KV
3.2 Electrical Conditions
Table 3.2. Electrical Conditions
PARAMETERS
DESCRIPTION
MIN
TYPICAL
MAX
UNIT
Ta
Working temperature
‐20
‐
105
℃
VCC
Working voltage
‐
3.6
VIL
IO low level input
‐0.3
‐
VCC*0.25
VIH
IO high level input
VCC*0.75
‐
VCC
VOL
IO low level output
‐
‐
VCC*0.1
VoH
IO high level output
VCC*0.8
‐
VCC
Imax
IO drive current
‐
‐
16
mA
Cpad
Input capacitor
‐
‐
pF
3.3 Wi-Fi Transmitting Current Consumptions
Table 3.3. Wi-Fi TX current consumption
PARAMETERS
MODE
RATE
Transmitting power
TYPICAL
UNIT
IRF
11b
1Mbps
+21.10dBm
287
mA
IRF
11g
6Mbps
+19.97dBm
255
mA
IRF
IRF
11n-HT20
MCS0
MCS0
+20.09dBm
+20.19dBm
244
220
mA
mA
11n-HT40
WR1 DATASHEET
3.4 Wi-Fi Receiving Current Consumptions
Table 3.4. Wi-Fi RX currentconsumption
PARAMETERS
MODE
TYPICAL
UNIT
IRF
CPU sleep
90
mA
IRF
CPU active
120
mA
3.5 Working Mode Current Consumptions
Table 3.5. The module working currentcon sumption
WORK MODE
AT TA=25℃
TYPICAL
MAX*
UNIT
EZ Mode
WR1 is under EZ paring mode, Wi‐Fi indicator
light flashes quickly
121.8
141
mA
Standby Mode
WR1 is connected, Wi‐Fi indicator light is on
52
125
mA
Operation Mode
WR1 is connected, Wi‐Fi indicator light is on
180
312
mA
Disconnection
Mode
WR1 is disconnected, Wi‐Fi indicator light is off
46
120
mA
Note: peak continuous time is about 5us.
The parameter shown above will vary dependingon different firmware functions.
4. WLAN Radio Specification
4.1 Basic Radio Frequency Characteristics
Table 41.Basic Radio frequency characteristics
PARAMETERS
DESCRIPTION
Frequency band
2412MHz-2462MHz
Wi‐Fi standard
IEEE 802.11n20/n40/g/b (Terminal 1‐11)
Data transmitting rate
11b:1,2,5.5,11(Mbps)
11g:6,9,12,18,24,36,48,54(Mbps)
11n:HT20,MCS0~7
11n:HT40,MCS0~7
Antenna type
On‐board PCB Antenna
4.2Wi-Fi Transmitting Power
Table 4.2. Wi-Fi transmitting power
WR1 DATASHEET
PARAMETERS
MIN
TYPICAL
MAX
UNI
RF average output power, 802.11b CCK Mode
1M
‐
21.10
‐
dBm
RF average output power, 802.11g OFDM Mode
6M
‐
19.97
‐
dBm
RF average output power, 802.11n20 OFDM Mode
MCS0
‐
20.09
‐
dBm
RF average output power, 802.11n40 OFDM Mode
MCS0
‐
20.19
‐
dBm
‐10
‐
10
ppm
The Frequency error
4.3Wi-Fi Receiving Sensitivity
Table 4.3. Wi-Fi Receiving sensitivity
PARAMETERS
MIN
TYPICAL
MAX
UNI
PER<8%, Receiving sensitivity, 802.11b CCK Mode
1M
‐
‐91
‐
dBm
PER<10%, Receiving sensitivity, 802.11g OFDM Mode
6M
‐
‐75
‐
dBm
PER<10%, Receiving sensitivity, 802.11n OFDM Mode
MCS0
‐
‐72
‐
dBm
WR1 DATASHEET
5. Antenna Information
5.1 Antenna Type
Antenna can be connectedusing On-board PCB antenna
Figure 5.1. Resistor definition for on-board PCB antenna Figure 5.2. Resistor definition for external antenna
5.2 Antenna Interference
While using the On-board PCBantenna, in order to have the best Wi-Fi performance, it’s
recommended to keep a minimum15mm distance between the antenna part and the other metal
pieces.
User’s own PCBA design is recommended NOT to pass any wire, NOT do copper pour under
the region of the module’s antenna, to avoid interferences.
WR1 DATASHEET
6. Packaging Information And Production Guide
6.1 Mechanical Dimensions
Figure 6.1. Top view of the module
6.2PCB Recommended Package
WR1 DATASHEET
6.3 Production Guide

The storage for the delivered module should meet the following condition:
1. The anti-moisture bag should be kept in the environment withtemperature< 30℃ and
humidity< 85% RH.
2. The expiration date is 6 months since the dry packaging products was sealed.
 Cautions:
1. All the operators should wear electrostatic ringin the whole process of production.
2. While operating, water and dirt should not have any contact with the modules.
6.4 Recommended furnace temperature curve
Figure 6.4. PCB Package DrawingRecommended furnace temperature curve
WR1 DATASHEET
Figure A.1. The application schematic design of the module
FCC Statement
Any Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment .This equipment should be installed and operated with
minimum distance 20cm between the radiator& your body.
FCC Label Instructions:
The outside of final products that contains this module device must display a label
referring to the enclosed module. This exterior label can use wording such as: “Contains
Transmitter Module FCC ID:2ANDL-WR1”,or “Contains FCC ID:2ANDL-WR1”, Any similar
wording that expresses the same meaning may be used.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : baclks150
Create Date                     : 2018:07:17 14:45:48+08:00
Modify Date                     : 2018:07:30 11:24:50-07:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2018:07:30 11:24:50-07:00
Producer                        : Acrobat Distiller 11.0 (Windows)
Format                          : application/pdf
Title                           : Microsoft Word - WR1_User manual.docx
Creator                         : baclks150
Document ID                     : uuid:cddff0be-20fe-45b6-83d2-e5fdca8d1cbf
Instance ID                     : uuid:132ba991-5311-4554-874e-ccbe76248745
Page Count                      : 11
EXIF Metadata provided by EXIF.tools
FCC ID Filing: 2ANDL-WR1

Navigation menu