Hansol LCD B15BF LCD Monitor User Manual

Hansol LCD Inc. LCD Monitor

User Manual

Parts 3Connection to Computer 4How to Adjust Monitor Angle 5Installing Monitor Driver 6Name and Function of Front 8Power Management Feature 10Adjusting OSD 11Standard Signal Table 17Specification 18Troubleshooting 19Warning 21Table of Contents
INFORMATION TO USER: This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation; if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Reorient / Relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit difference from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help. • Shielded interface cable has to be used to ensure product compliance. CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment
32PartsLCD MonitorPlace the monitor to face the user and then adjust the monitor angle.Take a break (for about 10 minutes) at every hour during the work with monitor. Refer to the following figure to take the correct posture. about 50cmLook down the monitorbelow the horizon.Relax shoulders and arms, and sit back on the chair.Adjust the monitor to prevent reflection.Adjust the monitor stand to acquire required angle.Keep feet flat on the ground.Maintain the arms horizontallyand place hands softly on the keyboard.Good Posture Guide12V-DC AdapterUser's Manual /Warranty CardSignal Cable AC Power CableInstallation DiskInstallation Diskette
5How to Adjust Monitor AngleHow to Default Stand4Connection to ComputerBasic Connection1. Use 220 V or 110 V. (Free Voltage)2. Connect monitor and computer via computer cable (See figure )3. Switch on power to monitor and computer.4. Installation is finished.12V DC connection terminal Computer cableFor PCFor MacintoshUse adapter.Adapter for Macintosh (Optional)Refer to the table on the rear side ofthe optional Macintosh adapter andadjust DIP switch by the resolution ofthe monitor.
76Click 'Finish'.Click 'Next>'.Click 'Advanced..'. Click 'Next>'.Click 'Monitor'.Click 'Display a list of all...'.Click 'Next>'.Click 'Have Disk..'.Select the driver and click 'OK'. Click 'Next>'.3. Select Exit if the monitor model is changed, and then reboot Windows.Installing Monitor Driver1. Insert the Diskette in the Floppy driver. 2. Double-click Install.exe in the Floppy driver folder using search function. 3. Select the model and click "OK".4. Select inf file of the model in Floppy driver, and then click "OK" button.5. Click "Exit" to close the installation.Automatic InstallationManual Installation1. Insert the Diskette in the Floppy driver.2. Click 'My Computer' and follow the procedure below.Click 'Control Panel'. Click 'Display'. Click 'Settings'.Run (Click) Install at Floppy driver and select the product model to set theoptimum display in Window 95, 98 or 2000.Use the Driver Floppy provided.
98Power SwitchPower switch is located in the lower center of the monitor stand.You can push the switch to turn on/off the power.Power Saving LEDIf the green LED around the power switch turns into blinking amber, it indicates the monitor is in power saving mode.On Screen Display (OSD) Function ButtonOSD buttons on the front of the monitor perform the following functions.MENU : Press this button to display menus.SELECT/ AUTO : Press this button, when OSD is not displayed, to performautomatic setting. When OSD is displayed, You can select the Item.POWER : Power switch.: By pressing this button when OSD is displayed, You can move cursor into the menus which You want.After press the select button, You can change the gauge level and items.FunctionsName and Function of Front Front panelSELECT/AUTO KEYMENU KEY+KEY-KEYPOWER KEY
11Horizontal PositionAdjusting OSDBrightnessContrastMENU1. Press the Menu button.2. Use to move Brightness ICON.3. Use SELECT button to select it.4. Use to adjust the brightness. SELECTMENU SELECTMENU SELECT1. Press the Menu button.2. Use to move Contrast ICON.3. Use SELECT button to select it.4. Use to adjust the contrast.1. Press the Menu button.2. Use to move H-Position ICON.3. Use SELECT button to select it.4. Use to adjust display left or right.10No image is displayed with LED blinking.Monitor is in power saving mode.Use mouse or keyboard to release power saving mode.No image is displayed without LED on.Power cable plug must be pulled out.Check the power plugs on monitor and on the wall."Out of range" displayed on the screen.This message is displayed when the signal from video card exceeds themaximum frequency of the monitor. Readjust resolution and frequency inaccordance with the monitor capacity. (Refer to Standard Signal Table)Power Management FeatureWhen not in use for a long period of time, the monitor automatically reduces its power consumption, meeting power savingstandards of EPA and NUTEK. The monitor is equipped with a power saving circuit that conforms to the world-standard Display Power Manager Signalling(DPMS) mode of Video Electronics Standard Association (VESA).The power management feature requires that the video card of thecomputer should support DPMS function. Status Color of LED Power ConsumptionNormal Green Normal PowerPower Cut Off Amber/Blinking( 2 second interval ) 5 W or Below
1312User ColorColorPreset Color1. Press the Menu button.2. Use to move Color ICON.3. Use SELECT button to select it.4. Use into the submenu.1. Use to move Red, Green, Blue ICON.2. Use SELECT button to select color what you want.3. Use to increase or decrease each color.4. Press the Menu button to exit.1. Use to select the I or II.2. Press the Menu button to exit.I: Blue tone II : Default colorClock PhaseVertical PositionClock 1. Press the Menu button.2. Use to move V-Position ICON.3. Use SELECT button to select it.4. Use to adjust display upward or downward.1. Press the Menu button.2. Use to move Clock Phase ICON.3. Use SELECT button to select it.4. Use to correct fine trembling or Video noise.1. Press the Menu button.2. Use to move Clock ICON.3. Use SELECT button to select it.4. If Auto-cnfig function fails to remove Video noise, Use orto remove vertical noise.( Adjusting clock phase is required after the adjustment of clock.) MENU SELECTMENU SELECTMENU SELECTMENUMENU SELECTMENUSELECT
1514LanguageOSD OverlayZoom Sharpness1. Use to move DOS Overlay ICON.2. Use SELECT button to select it.3. Use to adjust DOS Overlay.4. Press Menu button to exit.1. Use to move Zoom Sharpness ICON.2. Use SELECT button to select it.3. Use to adjust Sharpness.4. Press Menu button to exit.1. Press the Menu button.2. Use to move Language ICON.3. Use SELECT button to select it.4. Use to select language in order.SpecialVideo LevelDOS Mode1. Press the Menu button.2. Use to move SPECIAL ICON.3. Use SELECT button to select it.4. Use into the submenu.1. Use to move SPECIAL ICON.2. Use SELECT button to select it.3. Use to adjust level.4. Press the Menu button to exit.1. Use to move DOS Mode ICON.2. Use SELECT button to select it.3. Use to select DOS Mode what you want.4. Press Menu button to exit.MENU SELECTMENU SELECTMENUSELECTMENUSELECTMENUSELECTMENUSELECT
17Standard Signal TablePin assignment table D-SubMini 15pin connectorVGA (720 X 400)VGA (640 X 480)VGA (640 X 480)SVGA (800 X 600)XGA (1024 X 768)XGA (1024 X 768)MAC (640 X 480)MAC (832 X 624)MAC (1152 X 870)31.46931.46937.50046.87548.36360.02335.00049.72668.68170.08759.94075.00075.00060.00475.02966.66774.55175.06228.32225.17531.50049.50065.00078.75030.24057.284100.000ResolutionHorizontal Frequency (KHz)Vertical Frequency(Hz) Clock Frequency(MHz)1511 1561015pin D-SubPin No. Assignment Pin No. Assignment 1 Red Video 9 N.C2 Green Video 10 Ground3 Blue Video 11 Ground4 N.C 12 SDA5 Ground 13 H.Sync6 Red Video Ground 14 V.Sync7 Green Video Ground 15 SCL 8 Blue Video Ground16Auto-ConfigInformation1. Press the Menu button.2. Use to move the Auto-config ICON.You can know a display information(Horizontal, Vertical Frequency) 1. Press the Menu button.2. Use to move the Auto-config ICON.3. Use SELECT button to select it.4. Use or to readjust the display condition. In most cass, Auto-Config adjusts displayappropriately. Use PH or adjust CLKin accordance with graphic card to fine tunethe display.MENU SELECTMENUMENU SELECTMenu Exit1. Press the Menu button.2. Use to move the Exit ICON.3. Press SELECT button to exit.
1918TroubleshootingCheck the power connection. (Refer to page 4)Power LED is off.No picture.Check the signal cable between monitor and computer. (Refer to page 4)Perform Auto_config.Check the computer connection cable. (Refer to page 4)Check if computer power is on.Message, "No signal."is displayed on thescreen.Screen looks to be rundown.Perform Clock and Adjust PHASE.Switch off/on the monitor.Remove accessories (Video extension cable and others) and switch on.Screen is not clear.Check the resolution and frequency of computer and video card, and set up the again in reference to the current monitor mode and standard signal mode table.Display is unstable andtrembling.TypeAmorphous active matrix super TFT LCDScreen Size 38.1cm (Diagonal)Maximum Resolution1024 X 768 @ 75 HzPixel Range0.297 mm X 0.297 mmDisplay Colors 262,144 ColorContrast Rate 300 : 1Visual Angle 70° / 70° / 55° / 60° (Left / Right / Up / Down)Response Speed 25 msBrightness 250 cd/m 2Horizontal Frequency 80 kHz (Max.)Vertical Frequency 75 Hz (Max.)Video Signal Analog RGB (0.714 Vpp) 75 ohmSynchronous Signal Mode H, V Separate TTL Sync, SOG, COMPOSITEMaximum 47 WPower Saving Mode Under 5 WMENU, SELECT/AUTO, POWER, SWITCHInput: 85/265V (50~60 Hz), Output: 12V, 4.5A, 54WVESA StandardSafety Standard UL, CE, TUV, CBEMI FCC-BLow Radiation MPR-IISize and Weight 358 X 128 X 346 / 3.77 KgSpecificationLCDPanelSynchronizationModel B15BF l bVideoInputPower ConsumptionControl keyFront Part Wall MountSafetyStandard& EMIDimensionPower Adapter
2120WarningTo prevent damage or loss, please read this warning carefully.When connecting/disconnecting the plug, pull out the plug itself, and never pull the plug to prevent fire caused by short.To prevent electric shock, do not connect/dis-connect the plug with wet hand.To prevent fire, do not connect a large number ofequipment in a single line.To prevent fire and electric shock, pull out the plug incase of thunder and lightening.To prevent fire and electric shock, do not try to takethe monitor apart or repair it yourself. Contact yourlocal service station or customer service center forinspection, modification or repair.AUTO / EXIT VOLAUTO / EXIT VOLAUTO / EXIT VOLIf you see smoke or smell something burning, stopusing the unit, switch off the power, pull out the plug,and then contact your local service station.Check the resolution and frequency of computer and video card, and set up again in reference to the current monitor mode and standard signal mode table.Double images or'ghosts'.Perform Auto-Config.Adjust COLOR at User Mode in OSD Color Menu.Picture is dark.Picture is biased or cutor too wide.Monitor is in power saving mode.Power LED turns intoamber or blinkingamber.Adjust COLOR at User Mode in OSD Color Menu.Color is irregular.
22Memo

Navigation menu