Hansol LCD B15BF LCD Monitor User Manual
Hansol LCD Inc. LCD Monitor
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 158237 |
| Application ID | nwXNz5sMp2HxcDZC/I3EuQ== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 40.42kB (505199 bits) |
| Date Submitted | 2001-07-06 00:00:00 |
| Date Available | 2001-07-06 00:00:00 |
| Creation Date | 2001-06-01 11:40:33 |
| Producing Software | Acrobat Distiller 4.0.5 for Macintosh |
| Document Lastmod | 2001-07-06 10:49:00 |
| Document Title | User Manual |
Table of Contents Parts Connection to Computer How to Adjust Monitor Angle Installing Monitor Driver Name and Function of Front Power Management Feature 10 Adjusting OSD 11 Standard Signal Table 17 Specification 18 Troubleshooting 19 Warning 21 INFORMATION TO USER: This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation; if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Reorient / Relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit difference from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help. • Shielded interface cable has to be used to ensure product compliance. CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment Good Posture Guide Parts Place the monitor to face the user and then adjust the monitor angle. Take a break (for about 10 minutes) at every hour during the work with monitor. Refer to the following figure to take the correct posture. about 50cm Look down the monitor below the horizon. LCD Monitor Adjust the monitor to prevent reflection. Relax shoulders and arms, and sit back on the chair. Adjust the monitor stand to acquire required angle. Signal Cable AC Power Cable 12V-DC Adapter Maintain the arms horizontally and place hands softly on the keyboard. Installation Disk Keep feet flat on the ground. User's Manual / Warranty Card Installation Diskette Connection to Computer How to Adjust Monitor Angle Basic Connection 12V DC connection terminal How to Default Stand Computer cable For PC For Macintosh Use adapter. Adapter for Macintosh (Optional) Refer to the table on the rear side of the optional Macintosh adapter and adjust DIP switch by the resolution of the monitor. 1. Use 220 V or 110 V. (Free Voltage) 2. Connect monitor and computer via computer cable (See figure 3. Switch on power to monitor and computer. 4. Installation is finished. Installing Monitor Driver Run (Click) Install at Floppy driver and select the product model to set the optimum display in Window 95, 98 or 2000. Use the Driver Floppy provided. Click 'Advanced..'. Click 'Next>'. Click 'Monitor'. Automatic Installation 1. Insert the Diskette in the Floppy driver. 2. Double-click Install.exe in the Floppy driver folder using search function. 3. Select the model and click "OK". 4. Select inf file of the model in Floppy driver, and then click "OK" button. 5. Click "Exit" to close the installation. Click 'Display a list of all...'. Click 'Next>'. Click 'Have Disk..'. Manual Installation 1. Insert the Diskette in the Floppy driver. 2. Click 'My Computer' and follow the procedure below. Select the driver and click 'OK'. Click 'Next>'. Click 'Control Panel'. Click 'Display'. Click 'Settings'. Click 'Next>'. Click 'Finish'. 3. Select Exit if the monitor model is changed, and then reboot Windows. Name and Function of Front Front panel Functions Power Switch Power switch is located in the lower center of the monitor stand. You can push the switch to turn on/off the power. Power Saving LED If the green LED around the power switch turns into blinking amber, it indicates the monitor is in power saving mode. On Screen Display (OSD) Function Button OSD buttons on the front of the monitor perform the following functions. MENU : Press this button to display menus. SELECT/ AUTO : Press this button, when OSD is not displayed, to perform automatic setting. When OSD is displayed, You can select the Item. POWER : Power switch. : By pressing this button when OSD is displayed, You can move cursor into the menus which You want. After press the select button, You can change the gauge level and items. + KEY MENU KEY - KEY SELECT/ AUTO KEY POWER KEY Power Management Feature When not in use for a long period of time, the monitor automatically reduces its power consumption, meeting power saving standards of EPA and NUTEK. The monitor is equipped with a power saving circuit that conforms to the world-standard Display Power Manager Signalling (DPMS) mode of Video Electronics Standard Association (VESA). The power management feature requires that the video card of the computer should support DPMS function. Status Adjusting OSD Brightness MENU SELECT 1. Press the Menu button. 2. Use to move Brightness ICON. 3. Use SELECT button to select it. 4. Use to adjust the brightness. Color of LED Power Consumption Normal Green Normal Power Power Cut Off Amber/Blinking 5 W or Below ( 2 second interval ) Contrast MENU SELECT 1. Press the Menu button. 2. Use to move Contrast ICON. 3. Use SELECT button to select it. 4. Use to adjust the contrast. No image is displayed with LED blinking. Monitor is in power saving mode. Use mouse or keyboard to release power saving mode. No image is displayed without LED on. Power cable plug must be pulled out. Check the power plugs on monitor and on the wall. "Out of range" displayed on the screen. This message is displayed when the signal from video card exceeds the maximum frequency of the monitor. Readjust resolution and frequency in accordance with the monitor capacity. (Refer to Standard Signal Table) 10 Horizontal Position MENU SELECT 1. Press the Menu button. to move H-Position ICON. 2. Use 3. Use SELECT button to select it. 4. Use to adjust display left or right. 11 Color Vertical Position MENU SELECT 1. Press the Menu button. 2. Use to move V-Position ICON. 3. Use SELECT button to select it. 4. Use to adjust display upward or downward. MENU SELECT 1. Press the Menu button. 2. Use to move Color ICON. 3. Use SELECT button to select it. 4. Use into the submenu. Clock MENU Preset Color SELECT 1. Press the Menu button. 2. Use to move Clock ICON. 3. Use SELECT button to select it. 4. If Auto-cnfig function fails to remove Video noise, to remove vertical noise. Use or ( Adjusting clock phase is required after the adjustment of clock.) MENU 1. Use to select the I or II. 2. Press the Menu button to exit. I : Blue tone II : Default color Clock Phase MENU SELECT 1. Press the Menu button. to move Clock Phase ICON. 2. Use 3. Use SELECT button to select it. to correct fine trembling or Video noise. 4. Use 12 User Color SELECT MENU to move Red, Green, Blue ICON. 1. Use 2. Use SELECT button to select color what you want. 3. Use to increase or decrease each color. 4. Press the Menu button to exit. 13 OSD Overlay Special MENU SELECT SELECT 1. Use to move DOS Overlay ICON. 2. Use SELECT button to select it. 3. Use to adjust DOS Overlay. 4. Press Menu button to exit. 1. Press the Menu button. 2. Use to move SPECIAL ICON. 3. Use SELECT button to select it. 4. Use into the submenu. Zoom Sharpness Video Level SELECT SELECT MENU Language DOS Mode to move DOS Mode ICON. 1. Use 2. Use SELECT button to select it. to select DOS Mode what you want. 3. Use 4. Press Menu button to exit. 14 MENU to move Zoom Sharpness ICON. 1. Use 2. Use SELECT button to select it. 3. Use to adjust Sharpness. 4. Press Menu button to exit. 1. Use to move SPECIAL ICON. 2. Use SELECT button to select it. to adjust level. 3. Use 4. Press the Menu button to exit. SELECT MENU MENU MENU SELECT 1. Press the Menu button. to move Language ICON. 2. Use 3. Use SELECT button to select it. to select language in order. 4. Use 15 Standard Signal Table Auto-Config MENU SELECT 1. Press the Menu button. 2. Use to move the Auto-config ICON. 3. Use SELECT button to select it. 4. Use or to readjust the display condition. In most cass, Auto-Config adjusts display appropriately. Use PH or adjust CLK in accordance with graphic card to fine tune the display. Resolution Horizontal Frequency (KHz) Vertical Frequency (Hz) Clock Frequency (MHz) VGA (720 X 400) 31.469 70.087 28.322 VGA (640 X 480) 31.469 59.940 25.175 VGA (640 X 480) 37.500 75.000 31.500 SVGA (800 X 600) 46.875 75.000 49.500 XGA (1024 X 768) 48.363 60.004 65.000 XGA (1024 X 768) 60.023 75.029 78.750 MAC (640 X 480) 35.000 66.667 30.240 MAC (832 X 624) 49.726 74.551 57.284 MAC (1152 X 870) 68.681 75.062 100.000 Information MENU 1. Press the Menu button. 2. Use to move the Auto-config ICON. You can know a display information (Horizontal, Vertical Frequency) Menu Exit MENU SELECT 1. Press the Menu button. 2. Use to move the Exit ICON. 3. Press SELECT button to exit. 16 Pin assignment table D-Sub Mini 15pin connector Pin No. Assignment Red Video Pin No. Assignment N.C Green Video Blue Video 10 11 Ground Ground N.C Ground Red Video Ground 12 13 14 SDA H.Sync V.Sync Green Video Ground Blue Video Ground 15 SCL 10 11 15 15pin D-Sub 17 Specification Model LCD Panel B15BF Type Amorphous active matrix super TFT LCD Screen Size 38.1cm (Diagonal) Maximum Resolution 1024 X 768 @ 75 Hz Pixel Range 0.297 mm X 0.297 mm Display Colors 262,144 Color Contrast Rate 300 : 1 Visual Angle 70° / 70° / 55° / 60° (Left / Right / Up / Down) Response Speed 25 ms Brightness 250 cd/m 2 Synchro Horizontal Frequency nization Vertical Frequency Video Input Video Signal Front Part Power Adapter Wall Mount 18 Power LED is off. No picture. Message, "No signal." is displayed on the screen. Check the power connection. (Refer to page 4) Check the computer connection cable. (Refer to page 4) Check if computer power is on. 80 kHz (Max.) 75 Hz (Max.) Screen looks to be run down. Analog RGB (0.714 Vpp) 75 ohm Check the signal cable between monitor and computer. (Refer to page 4) Perform Auto_config. Synchronous Signal Mode H, V Separate TTL Sync, SOG, COMPOSITE Maximum Power Consumption Power Saving Mode Control key Troubleshooting 47 W Under 5 W MENU, SELECT/AUTO, POWER, SWITCH Screen is not clear. Input: 85/265V (50~60 Hz), Output: 12V, 4.5A, 54W Perform Clock and Adjust PHASE. Switch off/on the monitor. Remove accessories (Video extension cable and others) and switch on. VESA Standard Safety Standard Safety Standard EMI & EMI Low Radiation UL, CE, TUV, CB FCC-B Dimension Size and Weight 358 X 128 X 346 / 3.77 Kg MPR-II Display is unstable and trembling. Check the resolution and frequency of computer and video card, and set up the again in reference to the current monitor mode and standard signal mode table. 19 Warning To prevent damage or loss, please read this warning carefully. Color is irregular. Double images or 'ghosts'. Picture is dark. Adjust COLOR at User Mode in OSD Color Menu. When connecting/disconnecting the plug, pull out the plug itself, and never pull the plug to prevent fire caused by short. Check the resolution and frequency of computer and video card, and set up a gain in reference to the current monitor mode and standard signal mode table. To prevent electric shock, do not connect/disconnect the plug with wet hand. Adjust COLOR at User Mode in OSD Color Menu. If you see smoke or smell something burning, stop using the unit, switch off the power, pull out the plug, and then contact your local service station. AUTO / EXIT Picture is biased or cut or too wide. Perform Auto-Config. Power LED turns into amber or blinking amber. Monitor is in power saving mode. To prevent fire, do not connect a large number of equipment in a single line. To prevent fire and electric shock, pull out the plug in case of thunder and lightening. AUTO / EXIT AUTO / EXIT 20 VOL VOL VOL To prevent fire and electric shock, do not try to take the monitor apart or repair it yourself. Contact your local service station or customer service center for inspection, modification or repair. 21 Memo 22
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Create Date : 2001:06:01 11:40:33 Producer : Acrobat Distiller 4.0.5 for Macintosh Modify Date : 2001:07:06 10:49:00-07:00 Page Count : 13EXIF Metadata provided by EXIF.tools