Hansol LCD B17BF LCD Monitor User Manual users manual
Hansol LCD Inc. LCD Monitor users manual
users manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 177306 |
| Application ID | JhZwwuTJTBFmm4SGR1fAjA== |
| Document Description | users manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 32.54kB (406758 bits) |
| Date Submitted | 2001-11-02 00:00:00 |
| Date Available | 2001-10-31 00:00:00 |
| Creation Date | 2001-10-22 14:38:13 |
| Producing Software | Acrobat Distiller 4.0.5 for Macintosh |
| Document Lastmod | 2001-10-22 14:38:20 |
| Document Title | users manual |
INFORMATION TO USER : This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and,if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation; if this equipment does cause harmful interference to radio or television reception, which can be determined by determined by turning the equipment off and on, the user is encouraged to try to crrent the interference by one or more of the fllowing measures: 1. Reorient/Relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. Table of Contents Parts Connection to Computer The range of control Angle Installing Monitor Driver Name and Function of Front Power Management Feature 10 Adjusting OSD 11 Standard Signal Table 17 Specification 18 Troubleshooting 19 Warning 21 3. Connect the equipment into an outlet on a circuit difference from that to which the recerver is connected. 4. Consult the dealer or an experienced radio/TV technician for help. Shielded interface cable has to be used to ensure product compliance. CAUTION : Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user's authority to operate the equipment Good Posture Guide Parts Place the monitor to face the user and then adjust the monitor angle. Take a break (for about 10 minutes) at every hour during the work with monitor. Refer to the following figure to take the correct posture. about 50cm Look down the monitor below the horizon. Adjust the monitor to prevent reflection. LCD Monitor Relax shoulders and arms, and sit back on the chair. Adjust the monitor stand to acquire required angle. Signal Cable AC Power Cable Maintain the arms horizontally and place hands softly on the keyboard. Keep feet flat on the ground. Installation Disk User's Manual / Warranty Card 12V-DC Adapter For use only with power supply MANUFACTURER : ILAN MODEL : F19603A MANUFACTURER : EDAC MODEL : EA1050A Installation Diskette The range of control Angle Connection to Computer Basic Connection 12V DC connection terminal How to Adjust the Stand Forward 4 Computer cable For PC For Macintosh Use adapter. Adapter for Macintosh (Optional) Default Refer to the table on the rear side of the optional Macintosh adapter and adjust DIP switch by the resolution. 1. Use 220 V or 110 V. (Free Voltage) 2. Connect monitor and computer via computer cable (See figure 3. Power on the monitor and computer. 4. Connection is finished. Backward 31 Installing Monitor Driver Run (Click) "Install" at Floppy driver and select the model name to set the optimum display in Window 95, 98 or 2000. Use the Driver provided. Automatic Installation 1. Insert the Diskette to the Floppy Diskette driver. 2. Double-click "Install.exe". 3. Select the model(H710) and click "OK" button. 4. Select inf file, and then click "OK" button. 5. Click "Exit" button to close the installation. Click 'Advanced..'. Click 'Monitor'. Click 'Display a list of all...'. Click 'Next>'. Click 'Next>'. Click 'Change..'. Click 'Have Disk..'. Manual Installation 1. Insert the Diskette to the Floppy Diskette driver. 2. Click 'My Computer' and follow the procedure below. Select the driver and click 'OK'. Click 'Next>'. Click 'Control Panel'. Click 'Display'. Click 'Settings'. Click 'Next>'. Click 'Finish'. 3. Select "Exit" if the monitor model is changed, and then reboot the Windows. Name and Function of Front Front panel Functions Power button Power button is located in the lower center of the Front Bezel. You can push the button to turn on/off the power. Power Indicating LED If the green LED in the power switch turns into blinking green, it indicates the monitor is in power saving mode. On Screen Display (OSD) Function Button OSD buttons on the front of bezel perform the following functions. MENU BUTTON +/ -/ SELECT/ AUTO BUTTON BUTTON MENU : Press this button to display menus. SELECT/ AUTO : Press this button, when OSD is not displayed, to perform automatic setting. When OSD is displayed, You can select icons. POWER : Power button. +/ -/ : By pressing these button when OSD is displayed, You can move cursor into the menus which you want. After press the SELECT button, you can change gauge level or select sub menus. When OSD is not displayed, you can adjust brightness or contrast. BUTTON POWER BUTTON Power Management Feature When not in use for a long time, the monitor automatically reduces its power consumption, meeting power saving standards of EPA and NUTEK. The monitor is equipped with a power saving circuit that confirms to the world-standard Display Power Manager Signalling (DPMS) mode of Video Electronics Standard Association (VESA). The power management feature requires that the video card of the computer should support DPMS function. Status Normal DPMS mode Color of LED Power Consumption Green Normal Power Green Blinking 5 W or Below ( 2 second interval ) Adjusting OSD Brightness MENU 1. Press the Menu button. 2. Use to move Brightness ICON. 3. Use SELECT button to select it. to adjust the brightness. 4. Use 5. Use SELECT button to return previously state. Contrast MENU No image is displayed with Green blinking. Monitor is in power saving mode. Use mouse or keyboard to release power saving mode. No image is displayed without LED on. Power cable plug must be pulled out. Check the power plug on monitor and on the wall. "Out of range" displayed on the screen. This message is displayed when the signal from video card exceeds the maximum frequency of the monitor. Readjust resolution and frequency in accordance with the monitor capacity. (Refer to Standard Signal Table) SELECT SELECT 1. Press the Menu button. 2. Use to move Contrast ICON. 3. Use SELECT button to select it. to adjust the contrast.. 4. Use 5. Use SELECT button to return previously state. Horizontal Position MENU SELECT 1. Press the Menu button. to move H-Position ICON. 2. Use 3. Use SELECT button to select it. 4. Use to adjust display left or right. 5. Use SELECT button to return previously state. According to the characteristic of video card, control range can be changed. 10 11 Vertical Position MENU SELECT 1. Press the Menu button. 2. Use to move V-Position ICON. 3. Use SELECT button to select it. to adjust display upward or downward. 4. Use 5. Use SELECT button to return previously state. Color MENU SELECT 1. Press the Menu button. 2. Use to move Color ICON. 3. Use SELECT button into the submenu. According to the characteristic of video card, control range can be changed. Preset Color Clock MENU MENU SELECT 1. Press the Menu button. to move Clock ICON. 2. Use 3. Use SELECT button to select it. 4. If Auto-config function fails to remove Video noise, Use or to remove vertical noise. ( Adjusting clock phase is required after the adjustment of clock.) 5. Use SELECT button to return previously state. Clock Phase Clock Phase 1. Use to select the Mode 1,Mode 2,Mode 3. 2. Press the Menu button to exit. Model 1 : Maximum state of red,green,blue Model 2 : Bluish white Model 3 : Reddish white User Color Clock Phase SELECT MENU SELECT 1. Press the Menu button. to move Clock Phase ICON. 2. Use 3. Use SELECT button to select it. 4. Use to correct fine trembling or Video noise. 5. Use SELECT button to return previously state. 12 MENU 1. Use to move Red, Green, Blue ICON. 2. Use SELECT button to select color what you want. 3. Use to increase or decrease each color. 4. Use SELECT button to return previously state. 5. Press the Menu button to exit. 13 OSD Overlay Special Video Sharpness Level SELECT MENU to move Video Level ICON. 1. Use 2. Use SELECT button to select it. 3. Use to SELET level. 4. Use SELECT button to return previously state. 5. Press the Menu button to exit. 1. Press the Menu button. to move SPECIAL ICON. 2. Use 3. Use SELECT button into the submenu. OSD Overlay Sharpness SELECT MENU to move Sharpness ICON. 1. Use 2. Use SELECT button to select it. 3. Use to adjust Sharpness. 4. Use SELECT button to return previously state. 5. Press Menu button to exit. SELECT SELECT MENU to move OSD Overlay ICON. 1. Use 2. Use SELECT button to select it. 3. Use to adjust OSD Overlay. 4. Use SELECT button to return previously state. 5. Press Menu button to exit. Scale Mode DOS Mode SELECT 1. Use to move DOS Mode ICON. 2. Use SELECT button to select it. 3. Use to move DOS Mode what you want. 4. Press SELECT button to select it. 14 MENU SELECT SELECT SELECT 1. Use to move Scale Mode. 2. Use SELECT button to select it. to move Mode what you want. 3. Use 4. Use SELECT button to select it. 15 Factory Auto-Config Reset Language MENU SELECT 1. Press the Menu button. to move Language ICON. 2. Use 3. Use SELECT button to select it. 4. Use to select language in order. 5. Use SELECT button to return previously state. MENU SELECT 1. Press the Menu button. 2. Use to move the Factory Reset ICON. 3. Use SELECT button to return to default setting. Auto-Config Information Auto-Config MENU MENU SELECT 1. Press the Menu button. to move the Auto-config ICON. 2. Use 4. Use SELECT button to readjust the display condition. 1. Press the Menu button. 2. Use to move the Auto-config ICON. You can know a display information (Horizontal, Vertical Frequency) In most case, Auto-Config adjusts display appropriately. Use PH or adjust CLK in accordance with graphic card to fine tune the display. 16 17 Specification Standard Signal Table Resolution VGA Horizontal Frequency (KHz) Vertical Frequency (Hz) Clock Frequency (MHz) 31.469 70.087 28.322 Type Amorphous active matrix super TFT LCD Screen Size 43.2cm (Diagonal) Maximum Resolution 1280 X 1024 @ 75 Hz Pixel Range 0.264 mm X 0.264 mm Display Colors 16.7M Color Contrast Rate 400 : 1 Visual Angle 80째 / 80째 / 80째 / 80째 (Left / Right / Up / Down) Response Speed 40 ms Brightness 250 cd/m2 (720 X 400) VGA (640 X 480) 31.469 59.940 25.175 VGA (640 X 480) 37.500 75.000 31.500 VGA (640 X 480) 43.269 85.008 36.000 SVGA (800 X 600) 46.875 75.000 49.500 SVGA (800 X 600) 53.674 85.061 56.250 XGA (1024 X 768) 48.363 60.004 65.000 XGA (1024 X 768) 60.023 75.029 78.750 XGA (1024 X 768) 68.677 84.997 94.500 SXGA (1280 X 1024) 63.981 60.020 108.000 SXGA (1280 X 1024) 79.976 75.025 135.000 MAC (640 X 480) 35.000 66.667 30.240 MAC (832 X 624) 49.726 74.551 57.284 MAC (1152 X 870) 68.681 75.062 100.000 LCD Panel Synchro Horizontal Frequency nization Vertical Frequency Video Input 18 Assignment Red Video Green Video Blue Video N.C Ground Pin No. 10 11 12 13 Assignment N.C Ground Ground SDA H.Sync Red Video Ground Green Video Ground Blue Video Ground 14 15 V.Sync SCL Video Signal Power Saving Mode 10 11 75 Hz (Max.) Analog RGB (0.714 Vpp) 75 ohm 50W Under 5 W Control key Front Part MENU, SELECT/AUTO, POWER, +/ Wall Mount VESA Standard Safety Standard 79.9kHz (Max.) Synchronous Signal Mode H, V Separate TTL Sync, Maximum Power Consumption Pin assignment table D-Sub Mini 15pin connector Pin No. H710(B17BF Model -/ UL, CE, TUV, CB Safety Standard EMI & EMI Low Radiation FCC Dimension Size and Weight 420 X192.8 X443.5 / 6.3 Kg MPR-II 15 15pin D-Sub 19 Troubleshooting Power LED is off. No picture. Message, "No signal." is displayed on the screen. Color is irregular. Adjust COLOR at User Mode in OSD Color Menu. Double images or 'ghosts'. Check the resolution and frequency of computer and video card, and set up again in reference to the current monitor mode and standard signal mode table. Check the power connection. (Refer to page 4) Check the computer connection cable. (Refer to page 4) Check the computer power is on. Picture is dark. Screen looks to be run down. Check the signal cable between monitor and computer. (Refer to page 4) Perform Auto_config. Picture is biased or cut or too wide. Screen is not clear. Display is unstable and trembling. 20 Adjust COLOR at User Mode in OSD Color Menu. Remove attaches to the signal line (Video extension cable and others) and switch on. Perform Clock and Adjust PHASE. Switch off/on the monitor. Power LED turns into amber or amber blinking. Perform Auto-Config. Monitor is in power saving mode. Check the resolution and frequency of computer and video card, and set up again refer to the current monitor mode and standard signal mode table. 21 Warning Memo To prevent damage or loss, please read this warning carefully. When connecting/disconnecting the plug, pull out the plug itself, and never pull the cord to prevent fire caused by short. To prevent electric shock, do not connect/disconnect the plug with wet hand. If you see smoke or smell something burning, stop using the unit, switch off the power, pull out the plug, and then contact your local service station. To prevent fire, do not connect a large number of equipments in a single line. To prevent fire and electric shock, pull out the plug in case of thunder and lightening. To prevent fire and electric shock, do not try to take the monitor apart or repair it yourself. Contact your local service station or customer service center for inspection, modification or repair. 22 23
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Create Date : 2001:10:22 14:38:13 Producer : Acrobat Distiller 4.0.5 for Macintosh Modify Date : 2001:10:22 14:38:20-04:00 Page Count : 12EXIF Metadata provided by EXIF.tools