Hansol LCD B19BF 19` LCD MONITOR User Manual users manual

Hansol LCD Inc. 19` LCD MONITOR users manual

Contents

users manual

Download: Hansol LCD B19BF 19` LCD MONITOR User Manual users manual
Mirror Download [FCC.gov]Hansol LCD B19BF 19` LCD MONITOR User Manual users manual
Document ID363862
Application IDJ4LOQjwJOxxezkvJDn+DDA==
Document Descriptionusers manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize55.12kB (688963 bits)
Date Submitted2003-10-09 00:00:00
Date Available2003-10-09 00:00:00
Creation Date2003-07-05 10:04:21
Producing SoftwareAcrobat Distiller 4.0.5 for Macintosh
Document Lastmod2003-07-19 09:04:49
Document Titleusers manual

19
Printed on the recyclable paper
Printed in Korea
Part No. 942205010002- 01
USER'S MANUAL
TFT-LCD Color Monitor
INFORMATION TO USER :
This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.This equipment generates, uses and can
radiate radio frequency energy and,if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation; if this equipment does cause harmful interference to radio or
television reception, which can be determined by determined by turning the
equipment off and on, the user is encouraged to try to crrent the interference by
one or more of the fllowing measures:
1. Reorient/Relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
Table of Contents
Parts
Connection to Signal Source
the range of control Angle
Installing Monitor Driver
Name and Function of Front
Power Management Feature
10
Adjusting OSD
11
Hot Key
19
Standard Signal Table
19
Specification
20
Troubleshooting
22
Warning
24
3. Connect the equipment into an outlet on a circuit difference
from that to which the recerver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
CAUTION
Changes or modifications not expressly approved by the
manufacturer responsible for compliance could void the user's
authority to operate the equipment
ENERGY STAR
As an ENERGY STAR partner, Hansol Electronics Inc.
has determined that this product meets energy Star guidelines
for energy efficiency.
Good Posture Guide
Parts
Place the monitor to face the user and then adjust the monitor angle.
Take a break (for about 10 minutes) at every hour during the work with monitor.
Refer to the following figure to take the correct posture.
about 50cm
Look down the monitor
below the horizon.
Adjust the monitor to
prevent reflection.
LCD Monitor
Relax shoulders and arms,
and sit back on the chair.
Adjust the monitor stand
to acquire required angle.
Maintain the arms horizontally
and place hands softly on
the keyboard.
Signal Cable (Analog)
Stereo Cable(Option)
AC Power Cable
Keep feet flat on the ground.
User's Manual /
Warranty Card
2 - English
Installation Diskette
Signal Cable (DVI)
English - 3
Connection to Signal Source
Basic Connection
The range of control Angle
How to Adjust the Stand
Port for AC power cable
Port for Audio cable from audio source.
Port for Head Phone or External Speaker
Port for signal cable from DVI signal source.
Kensington Lock
Port for signal cable from analog signal source.
Forward 5
< Power source connection >
< Signal cable connection>
General
For Macintosh
Default
Adapter for Macintosh (Optional)
Refer to the table on the rear side of
the optional Macintosh adapter and
adjust DIP switch by the resolution.
1. Use 220 V or 110 V. (Free Voltage)
2. Connect monitor and Signal Source via Signal cable
3. Power on the monitor and computer.
4. Connection is finished.
4 - English
Backward 33
English - 5
Installing Monitor Driver
Run (Click) "Install" at Floppy Diskette driver and select the model name to
set the optimum display in Window 95, 98 or 2000, XP.
Use the Driver provided.
Automatic Installation
1. Insert the Diskette to the Floppy Diskette driver.
2. Double-click "Install.exe".
3. Select the model and click "OK" button.
4. Select inf file, and then click "OK" button.
5. Click "Exit" button to close the installation.
Click 'Advanced..'.
Click 'Monitor'.
Click 'Display a list of all...'.
Click 'Next>'.
Click 'Next>'.
Click 'Change..'.
Click 'Have Disk..'.
Manual Installation
1. Insert the Diskette to the Floppy Diskette driver.
2. Click 'My Computer' and follow the procedure below.
Select the driver and click 'OK'.
Click 'Next>'.
Click 'Control Panel'.
6 - English
Click 'Display'.
Click 'Settings'.
Click 'Next>'.
Click 'Finish'.
3. Select "Exit" if the monitor model is changed, and then reboot the Windows.
English - 7
Name and Function of Front
Front panel
Functions
Power button
Power button is located in the lower center of the Front Bezel.
You can push the button to turn on/off the power.
Power Indicating LED
Dark : Power off
Green : Normal mode
Green blinking : DPMS mode or Check Signal Cable mode.
On Screen Display (OSD) Function Button
OSD buttons on the front of bezel perform the following functions.
VOL / MUTE BUTTON
SOURCE BUTTON
MENU/EXIT BUTTON
/ + BUTTON
SELECT/ AUTO BUTTON
/ - BUTTON
POWER BUTTON
8 - English
SOURCE : Press this button to change Analog/DVI display.
MENU/EXIT : Press this button to display menus. if you press this button when
OSD is displayed, you can switch display to the previous menu and
exit menu.
SELECT/ AUTO : Press this button, when OSD is not displayed, to perform
automatic setting.
When OSD is displayed, You can select icons.
POWER : Power button.
+/
: By pressing these button when OSD is displayed, You can move
-/
cursor into the menus which you want.
After press the SELECT button, you can change gauge level or
select submenus.
When OSD is not displayed, you can adjust brightness or contrast.
VOLUME / MUTE : Press this button for volume control. when control is displayed,
You can control mute by pressing this button
English - 9
Power Management Feature
The monitor is equipped with a power saving circuit that
confirms to the world-standard Display Power Manager Signalling
(DPMS) mode of Video Electronics Standard Association (VESA).
The power management feature requires that the video card of the
computer should support DPMS function.
Status
LED Sign
Power Consumption
Normal mode
Green ON
Normal Power
DPMS mode
Green Blinking
Input Source
MENU
SELECT
1. Press the MENU button to access main menu.
2. Use
to move Input source ICON.
3. Press SELECT button into the submenu.
1W or Below(Analog)/
3.5W or Below(DVI)
DPMS with Audio (Option)
Mute ON
Adjusting OSD
1W or Below(Analog)/
3.5W or Below(DVI)
Digital Input
SELECT
Mute OFF
10W or Below
1. Use
to move Digital input ICON.
2. Press SELECT button to select DVI display.
No image is displayed with Green blinking.
Monitor is in power saving mode.
Use mouse or keyboard to release power saving mode.
No image is displayed without LED on.
Power cable plug must be pulled out.
Check the power plug on monitor and on the wall.
"Out of range" displayed on the screen.
This message is displayed when the signal from video card exceeds the
maximum frequency of the monitor. Readjust resolution and frequency in
accordance with the monitor capacity. (Refer to Standard Signal Table)
10 - English
Analog Input
SELECT
1. Use
to move Analog input ICON.
2. Press SELECT button to select Analog display.
English - 11
Image
Brightness &Contrast
MENU
SELECT
1. Press the MENU button to access main menu.
to move Brightness and Contrast ICON.
2. Use
3. Press SELECT button into the submenu.
Brightness
SELECT
1. Use
to move Brightness ICON.
2. Press SELECT button to select it.
3. Use
to adjust the brightness.
SELECT
MENU
1. Press the MENU button to access main menu.
2. Use
to move Image ICON.
3. Press SELECT button into the submenu.
Horizontal Position
SELECT
1. Use
to move H-Position ICON.
2. Press SELECT button to select it.
3. Use
to adjust display left or right.
According to the characteristic of video card,
control range can be changed.
Contrast
SELECT
1. Use
to move Contrast ICON.
2. Press SELECT button to select it.
3. Use
to adjust the contrast.
Vertical Position
SELECT
1. Use
to move V-Position ICON.
2. Press SELECT button to select it.
3. Use
to adjust display upward or downward.
According to the characteristic of video card,
control range can be changed.
12 - English
English - 13
Preset Color
Clock Phase
MENU
SELECT
1. Press
to move Clock Phase ICON.
2. Use SELECT button to select it.
3. Use
to correct fine trembling or Video noise.
1. Use
to select the 6500K, and 9300K.
2. Press the Menu button to return previous state.
6500K : Reddish white
User Color
Clock
SELECT
SELECT
to move Clock ICON.
1. Use
2. Press SELECT button to select it.
3. Press or
to remove vertical noise.
( Adjusting clock phase is required after the
adjustment of clock.)
SELECT
1. Press MENU button to access main menu.
2. Use
to move Color ICON.
3. Press SELECT button into the submenu.
14 - English
MENU
1. Use
to move User color ICON.
2. Press SELECT button to select it.
3. Use
to Shift the Color what you want.
4. Use select button to select it.
5. Use
to increase or decrease each color.
6. Press the menu button to return previous state.
Special
Color
MENU
9300K : Bluish white
MENU
SELECT
1. Press MENU button to access main menu.
2. Use
to move Specal ICON.
3. Press SELECT button into the submenu.
English - 15
Language
MENU
SELECT
1. Use
to move Language ICON.
2. Press SELECT button to select it.
3. Use
to select language.
Factory
Auto-Config
Reset
SELECT
SELECT
1. Use
to move OSD H-Position ICON.
2. Press SELECT button to select it.
3. Use
to adjust OSD left or right.
OSD V-Position
SELECT
1. Use
to move the Factory Reset ICON.
2. Press SELECT button to return to default setting.
Auto-Config
Information
MENU
OSD H-Position
1. Use
to move OSD V-Position ICON.
2. Press SELECT button to select it.
3. Use
to adjust OSD upward or downward.
OSD Time
SELECT
1. Use
to move the Information ICON.
2. Press SELECT button to select it.
You can know display information
SELECT
1. Use
to move OSD Time ICON.
2. Press SELECT button to select it.
3. Use
to adjust OSD display time.
Accoding to the characteristic of video card,
display information can be incorrect
16 - English
English - 17
Sound
Auto-Config
(Option)
MENU
SELECT or
VOL BUTTON
1. Use
to move Sound ICON.
2. Press SELECT button to select it.
to control volume.
3. Use
4. Press MENU button to return previous state.
1. When change DVI display into Analog display, select source button located in the left.
Analog display will be showed after Analog input message.
2. When change Analog display into DVI display, select source button located in the left.
DVI display will be showed after DVI input message.
3. No signal input message will be displayed when video card output is not mated with
monitor source.
Standard Signal Table
Resolution
18 - English
Horizontal Frequency
(KHz)
Vertical Frequency
(Hz)
Clock Frequency
(MHz)
VGA
(720 X 400)
31.469
70.087
28.322
VGA
(640 X 480)
31.469
59.940
25.175
VGA
(640 X 480)
37.500
75.000
31.500
SVGA (800 X 600)
37.900
60.320
40.000
SVGA (800 X 600)
46.875
75.000
49.500
XGA (1024 X 768)
48.363
60.004
65.000
XGA (1024 X 768)
60.023
75.029
78.750
SXGA (1280 X 1024)
63.981
60.020
108.000
SXGA (1280 X 1024)
79.976
75.025
135.000
MAC (640 X 480)
35.000
66.667
30.240
MAC (832 X 624)
49.726
74.551
57.284
MAC (1152 X 870)
68.681
75.062
100.000
English - 19
Pin assignment table D-Sub
Mini 15pin connector
Specification
Model
Pin No.
Assignment
Red Video
Green Video
Blue Video
N.C
Ground
Red Video Ground
Pin No.
10
11
12
13
14
Assignment
5V Input
Ground
Ground
SDA
H.Sync
V.Sync
Green Video Ground
Blue Video Ground
15
SCL
10
11
LCD
Panel
15
15pin D-Sub
H950 (B19AF
Type
Amorphous active matrix super TFT LCD
Screen Size
48.3cm (Diagonal)
Maximum Resolution
1280 X 1024 @ 75 Hz
Pixel Range
0.294 mm X 0.294 mm
Display Colors
16.7M Color
Contrast Ratio
500 : 1
Viewing Angle
85째 / 85째 / 85째 / 85째 (Left / Right / Up / Down)
Response Time
25 msec
Luminance
250 cd/m
Synchro Horizontal Frequency
nization Vertical Frequency
Video
Input
8 D1
D2
Analog RGB (0.714Vpp) 75 ohm/ Digital(TMDS)
Sync Type
H, V Separate TTL Sync,
Maximum
Power
Consumption Power Saving Mode
D4
Pin No.
Assignment
Audio
Output
Under 1 W(Analog) / Under 3.5 W(DVI)
SOURCE MENU / EXIT, AUTO/SELECT, POWER,
, +/ , VOL/MUTE
Normal
1W/Ch
Max
1.5W/Ch
Power Supply
Input : 100-240Vac (50/60 Hz), 0.6A
Wall Mount
VESA Standard
Safety Standard
20 - English
48W
-/
24 D3
Pin No. Assignment Pin No. Assignment Pin No. Assignment
75 Hz (Max.)
Video Signal
Control key Front Part
17
79.9kHz (Max.)
UL, CE, TUV, CB
Safety
Standard EMI
& EMI
Low Radiation
MPR-II
Dimension Size and Weight
418 200 437.2 / 6.3kg
FCC,RRL
English - 21
Troubleshooting
Power LED is dark.
No picture.
OSD, "check signal."
is displayed on the
screen.
Message, "check cable."
is displayed on the
screen.
Screen looks to be run
down.
Check the power connection.
(Refer to page 4)
Color is irregular.
Adjust COLOR at User Mode in OSD Color
Menu.
Check the computer power is on.
Double images or
'ghosts'.
Check the resolution and frequency of
computer and video card, and set up
again in reference to the current monitor
mode and standard signal mode table.
Check the signal cable between monitor
and computer. (Refer to page 4)
Picture is dark.
Perform Auto_config.
Picture is biased or cut
or too wide.
Screen is not clear.
Display is unstable and
trembling.
22 - English
Adjust COLOR at User Mode in OSD Color
Menu.
Remove attaches to the signal line
(Video extension cable and others)
and switch on.
Perform Auto-config.
Adjust clock and PHASE.
Check the resolution and frequency of
computer and video card, and set up
again refer to the current monitor
mode and standard signal mode table.
Power LED turns into
Green blinking.
NO SOUND
Perform Auto-Config.
Monitor is in DPMS mode.
Check the voice signal connection code or
adjust volume
English - 23
Warning
To prevent damage or loss, please read this warning carefully.
When connecting/disconnecting the plug, pull out
the plug itself, and never pull the cord to prevent fire
caused by short.
To prevent electric shock, do not connect/disconnect the plug with wet hand.
If you see smoke or smell something burning, stop
using the unit, switch off the power, pull out the plug,
and then contact your local service station.
To prevent fire, do not connect a large number of
equipments in a single line.
To prevent fire and electric shock, pull out the plug in
case of thunder and lightening.
To prevent fire and electric shock, do not try to take
the monitor apart or repair it yourself. Contact your
local service station or customer service center for
inspection, modification or repair.
24 - English
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 2003:07:05 10:04:21
Producer                        : Acrobat Distiller 4.0.5  for Macintosh
Modify Date                     : 2003:07:19 09:04:49+09:00
Page Count                      : 14
EXIF Metadata provided by EXIF.tools
FCC ID Filing: MSAB19BF

Navigation menu