Hanwha Techwin DIGIMAXV700 Digital Camera User Manual v700en 02 V05
Samsung Techwin Co Ltd Digital Camera v700en 02 V05
Users Manual
Thank you for buying a Samsung Camera.
This manual will guide you through using the camera, including capturing images, downloading images and
using the software applications. Please read this manual carefully before using your new camera.
Figures and images used in this manual are based on the Samsung Digimax V700.
ENGLISH
V100
2
Instructions
Use this camera in the following order
Insert the
USB cable
Set up the
camera driver
Before connecting the camera to a PC, via the
USB cable, you will need to set up the camera
driver. Install the camera driver that is contained in
Application software CD-ROM.(p.90)
Take a picture (p.19)
Insert the supplied USB cable into the PC’s USB
port and the camera’s USB connection
terminal.(p.98)
Check the camera’s power. If the power is turned
off, press the camera button to turn it on.
Take a picture
Check the
camera’s power
Check
[Removable Disk]
Open Window s EXPLORER and search for
[Removable Disk].(p.99)
If you use a card reader to copy the images on the memory card to your PC, the images
could be damaged. When transferring the images taken with the camera to your PC, be sure
to use the supplied USB cable to connect the camera to your PC. Please note that the
manufacturer holds no responsibility for loss or damage of images on the memory card due
to the use of a card reader.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION : Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
Information to the user
Getting to know your camera 5
About the icons 5
Danger 6
Warning 6
Caution 7
An FCC warning 7
System chart 8
Identification of features 10
Front & Top 10
Back & Bottom 11
Side/ 5-function button 12
Mode dial 12
Connecting to a Power Source 15
Using the batteries 15
Removing the battery 15
Using the AC power adapter
(SAC-51, 5.0V) 16
Instructions on how to use the
memory card 17
Maintenance of the memory card 17
Preserving the memory card data 17
Inserting the memory card 19
Removing the memory card 19
When Using the Camera for the
First Time 20
LCD monitor indicator 21
Starting the recording mode 22
How to use the AUTO mode 22
How to use the PROGRAM mode 23
How to use the A/S/M mode 23
How to use the MySET mode 24
How to use the VOICE RECORDING
mode 24
How to use the MOVIE CLIP mode 25
NIGHT SCENE mode 25
How to use the SCENE mode 26
Things to Watch Out for When Taking
Pictures 27
Using the camera buttons to adjust the
camera 28
POWER button 28
SHUTTER button/ Jog dial 28
ZOOM W/T button 28
Voice memo/ UP button 31
Macro/ Down button (Focusing) 32
Focus lock 33
FLASH/ LEFT button 34
Self-timer/ Remote/ Right button 36
MENU/ OK button 38
S button 38
MF button 44
LCD button 45
AEL button (Automatic Exposure Lock) 45
Using the LCD monitor to adjust the
camera settings 46
How to use the menu 48
Size 48
Quality 49
Metering 50
Effect 50
Sharpness 51
Continuous shot 51
Save / Load a specific camera
configuration(MySET) 52
Scene 53
Starting play mode 54
Playing back a still image 54
3
Contents
READY
RECORDING
PLAY
4
Contents
Playing back a movie clip 55
Playing back a recorded voice 55
LCD monitor indicator 56
Using the camera buttons to adjust the
camera 57
Thumbnail/ Enlargement button 57
Voice memo / Up button 58
Play & Pause/ Down button 59
LEFT/ RIGHT/ MENU/ OK button 60
LCD button 60
Delete button 61
Setting up the play back function using the
LCD monitor 62
Deleting images 64
Protecting images 65
Starting the slide show 66
Resize 67
Rotating an image 68
DPOF 68
DPOF : STANDARD 69
DPOF : INDEX 69
DPOF : PRINT SIZE 70
DPOF : CANCEL 70
PictBridge 71
PictBridge: Picture Selection 72
PictBridge: Print Setting 73
PictBridge: Picture Printing 74
PictBridge : DPOF AUTO PRINT 75
PictBridge : RESET 75
Setup menu 76
File name 77
Auto power off 78
Language 79
Formatting a memory card 79
Setting up the Date/ Time/ Date type 80
Imprinting the recording date 80
Function lamp 81
Sound 82
LCD brightness 82
Selecting Video out type 83
Quick view 84
Connecting an External Device (USB) 84
Initialisation(RESET ALL) 85
Setting up the MYCAM menu 86
Start up image 86
Start up sound 87
Shutter sound 87
Important notes 88
Warning indicator 90
Before contacting a service centre 91
Specifications 94
Software Notes 96
System Requirements 96
About the software 97
Setting up the application software 98
Starting PC Mode 107
Removing the USB Driver for
Windows 98SE 110
Removable Disk 111
Removing the removable disk 112
Setting up the USB Driver for MAC 113
Using the USB Driver for MAC 113
Digimax Viewer 2.1 114
Using PhotoImpression 115
Digimax Reader 116
FAQ 118
SETUP
SOFTWARE
5
Getting to know your camera
Thank you for buying a Samsung Digital Camera.
Prior to using this camera, please read the user manual thoroughly.
When you require After Sales service, please bring the camera and the cause of the camera
malfunction (such as Batteries, Memory card etc.) to the A/S centre.
Please check that the camera is operating properly prior to when you intend to use it (e.g. for
a trip or an important event) to avoid disappointment. Samsung camera takes no
responsibility for any loss or damages that may result from camera malfunction.
Keep the manual in a safe place.
Microsoft, Windows and Windows logo are registered trademarks of Microsoft Corporation
incorporated in the United States and/or other countries.
Apple, Mac and QuickTime logo are registered trademarks of Apple computer.
All brand and product names appearing in this manual are registered trademarks of their
respective companies.
This manual contains instructions on using this camera that will help you to use this camera
safely and correctly. This will help prevent danger and injury to others.
About the icons
DANGER
DANGER indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING
WARNING indicates a potentially hazardous situation, which, if not avoided,
could result in death or serious injury.
CAUTION
CAUTION indicates a potentially hazardous situation, which, if not avoided,
may result in a minor or moderate injury.
6
Danger
Do not attempt to modify this camera in any way. This may result in fire, injury, electric shock
or severe damage to you or your camera. Internal inspection, maintenance and repairs
should be carried out by your dealer or Samsung Camera Service centre.
Please do not use this product in close proximity to flammable or explosive gases, as this
could increase the risk of explosion.
Should any form of liquid or a foreign object enter the camera, do not use it. Switch off the
camera, and then disconnect the power source (batteries or AC Power Adapter). You must
contact your dealer or Samsung Camera Service centre. Do not continue to use the camera
as this may cause a fire or electric shock.
Do not insert or drop metallic or inflammable foreign objects into the camera through access
points e.g. the memory card slot and battery chamber. This may cause a fire or electric
shock.
Do not operate this camera with wet hands. This could pose a risk of electric shock.
Do not use the flash in close proximity to people or animals. Positioning the flash too close to
your subject’s eyes, may cause eyesight damage.
When taking photographs, never point the lens of the camera directly into very strong light.
This may result in permanent damage to your eyesight.
For safety reasons keep this product and accessories out of reach of children or animals to
prevent accidents e.g.:
Swallowing batteries or small camera accessories. If an accident should occur, please
consult a doctor immediately.
There is the possibility of injury from the camera’s moving parts.
Batteries and camera may become hot during prolonged use and it may result in camera
malfunction. Should this be the case, allow the camera to sit idle for a few minutes to allow it
time to cool.
Do not recharge non rechargeable batteries. This may cause an explosion.
Do not leave this camera in places subject to extremely high temperatures, such as a sealed
vehicle, direct sunlight or other places of extreme variances in temperature. Exposure to
extreme temperatures may adversely affect the camera s internal components and could
cause a fire.
When in use, do not cover the camera or AC Power Adapter. This may cause heat to build up
and distort the camera body or cause a fire. Always use the camera and its accessories in a
well-ventilated area.
Warning
7
Caution
Leaking, overheating, or burst batteries could result in fire or injury.
Use batteries with the correct specification for the camera.
Do not short circuit, heat or dispose of batteries in fire.
Do not insert the batteries with the reverse polarities.
Remove the batteries when not planning to use the camera for a long period of time.
Batteries may leak corrosive electrolyte and permanently damage the camera's components.
Do not fire the flash while it is in contact with hands or objects. Do not touch the flash after
using it continuously. It may cause burns.
Do not move the camera while it is switched on, if you are using the AC Power Adapter.
After use, always switch off the camera before unplugging the adapter from the wall socket.
Then make sure that any connector cords or cables to other devices are disconnected before
moving the camera. Failure to do so may damage the cords or cables and cause a fire or
electric shock.
A non-rechargeable (disposable) battery can be used but has a short lifespan because of its
relatively low battery capacity. We recommend the rechargeable battery which has a bigger
capacity and longer lifespan than the non rechargeable type. (Rechargeable batteries may
not be available everywhere).
An FCC warning
This device has been tested in accordance with the limits of a class B digital device
under item 15 of the FCC rules. These limits are designed to provide protection
against harmful interference in commercial installation. This equipment generates,
absorbs and can emit radio frequency energy. If it is not installed and used in
accordance with the instructions, it may cause harmful interference to radio
communication. There is however, no guarantee that interference will not occur in
some situations. Should any interference occur when this device is in operation,
please try one or more of the following measures.
Change the location and direction of any aerial.
Increase distance between the camera and the affected device.
Use a different socket away from the affected device.
Please contact a Samsung agent or a radio/TV engineer.
This device complies with part 15 of the FCC Rules.
Changes or modifications not expressly approved by the party responsible for
compliance could void user's authority to operate the equipment.
8
System chart
Please check that you have the correct contents before using this product. To buy the optional
equipment, contact your nearest Samsung dealer or Samsung service centre.
Pouch User manual Camera strap Software CD
(see p.90)
SD memory card
(see p.15)
DPOF compatible
printer(see p.59)
Rechargeable
battery(SLB-1137)
Battery charger
CHARGE
AC cord
Duracell
CP-1 battery
< Included items >
9
System chart
USB cable AV cable
PictBridge compatible
printer(see p.71)
Computer
(see p.107)
External monitor
Yellow cable – Video
White colour - Voice
(see p.76)
For Windows
PC with processor better than MMX Pentium
233MHz (XP : Pentium II 300MHz)
Windows 98/98SE/2000/ME/XP
Minimum 32MB RAM (XP : 128MB)
140MB of available hard-disk space
USB port
CD-ROM drive
800x600 pixels, 16-bit colour display
compatible monitor (24-bit colour display
recommended)
For Macintosh
Power Mac G3 or later
Mac OS 9.0 ~ 10.3
Minimum 64MB RAM
110MB of available hard-disk space
USB port
CD-ROM drive
QuickTime 6.0 or later for Movie Clip
System Requirements
When you connect the camera to a
computer, printer or external monitor, you
have to use the USB/ Video cable supplied
with the camera, or the external devices can't
recognise the camera.
CAUTION
10
Identification of features
Front & Top
Back
jog dial
Flash
Lens
Power button
Mode dial lamp
Microphone
Auto Focus
lamp & Self-
timer lamp
Mode dial
MF button
(Album button)
Autofocus indicator
lamp(Green)
Strap eyelet
Zoom T button
(Digital zoom)
Zoom W button
(Thumbnail)
Play mode button
LCD monitor
DC input
connection point
USB/ AV
connection terminal
Shutter button
Speaker
AEL/ASM
button
+/-, DELETE
button
Flash indicator lamp(Red) LCD button
5-function button
Remote control sensor
Tripod socket
Viewfinder
11
Identification of features
PROGRAM mode
Please select this mode for quick and easy picture taking
with minimal user interaction.
Selecting the automatic mode will configure the camera with
optimal settings. You can still manually configure all
functions except the iris and shutter speed.
AUTO mode
You can select the desired working mode by using the mode dial located on the back of the
camera. This digital camera has 8 recording modes. These are listed below.
Side/ 5-function button
Mode dial
Memory card slot
Battery chamber cover
FLASH/ LEFT
button
MENU/ OK
button
Macro/ Play & Pause button/ DOWN
button
SELF-TIMER/
RIGHT button
Voice Recording
/ Voice memo/ UP button
Battery
chamber
Battery holder
12
Identification of features
Set the aperture value for automatic exposure depends on the
brightness of the object by automatic shutter speed setting in
the camera.
A (Aperture priority) shooting mode
Set the shutter speed for automatic exposure depends on the
brightness of the object by automatic aperture value setting in
the camera.
S (Shutter priority) shooting mode
The user can manually set both the aperture value and the
shutter speed.
M (Manual) shooting mode
This mode allows users to save frequently used shooting
settings for later use.
MySET mode
A movie clip can be recorded for as long as the available
recording time of the memory capacity allows.
- Image size : 640X480, 320X240, 160X120 (user selectable)
- Movie clip file type : *.avi
MOVIE CLIP mode
Use the menu to easily configure optimal settings for a variety
of shooting situations. These include NIGHT, PORTRAIT,
CHILDREN, LANDSCAPE, CLOSE UP, TEXT,
RECOGNITION, SUNSET, DAWN, BACKLIGHT,
FIREWORKS and BEACH & SNOW scenes.
SCENE mode
13
Identification of features
Self-timer lamp (Based on 10-second Self-timer; see p. 35)
MODE
Icon
Icon
MODE SCENE
AUTO
PROGRAM
MySET
VOICE RECORDING
Night
MOVIE CLIP
PLAY
Children
Landscape
Close up
Sunset Dawn
Backlight Fireworks
Beach & Snow
Auto focus indicator lamp
Mode dial lamp
Flash indicator lamp
Mode icons
A priority
Portrait
Text
S priority
Manual
Colour Status Camera Status
Blinking
- For the first 7 seconds, the LED blinks at 1second intervals.
- For the final 3 seconds, the LED blinks quickly at 0.25-second
intervals.
Red
Colour Status Camera Status
Blinking
Recording Mode (lightly press the shutter button): Not focused
PC Mode: Transmitting Data
Recording Mode (lightly press the shutter button): Focused
On
Green
Colour Status Camera Status
Blinking Flash in the process of charging
Flash ready
ON
Red
Colour Status Camera Status
ON
Turned off the LCD with the LCD button.
PC Mode: When the USB cable is inserted.
Green
14
Connecting to a Power Source
Important information about battery usage
When the camera is not used, turn off the camera power.
Do not charge the non rechargeable batteries. It may cause an explosion.
Please remove the batteries if the camera will not be used for long periods.
Batteries can lose power over time and are prone to leaking if kept inside the camera.
Low temperatures (below 0°C) can affect the performance of the batteries and you may
experience reduced battery life.
Batteries will usually recover at normal temperatures.
During extended use of the camera, the camera body may become warm.
This is perfectly normal.
If the camera is in PC mode, slide show, playing back a voice recording or playing back a
movie clip, it is recommended that you use an AC adapter.
INFORMATION
There are two ways in which to provide the camera with power. You can use batteries or
alternatively, you can use an AC(100 ~ 250V) Adapter (DC 3.3V 2.0A).
We recommend using batteries for a digital camera (use batteries that are within a year of
their date of manufacture). The batteries are listed below. Non rechargeable batteries :
Duracell CP-1 batteryRechargeable batteries : SLB-1137
15
Connecting to a Power Source
Always turn off the power before taking the AC adapter out of the mains supply.
As with all mains powered devices, safety is important. Ensure that neither the camera
nor adapter comes into contact with water or metallic materials.
Please ensure that you use an AC adapter (3.3V 2.0A) with the correct specification for
the camera. Failure to do so may affect your warranty.
DANGER
If you have access to a mains supply, using an AC
Adapter (3.3V 2.0A) allows the camera to be used
for long periods of time. Plug the adapter into the
connection point (DC IN 3.3V) on the camera.
Remove the batteries from the camera when using
an AC adapter.
Using the AC power adapter (3.3V 2.0A)
16
Connecting to a Power Source
Using the batteries
Battery status
Battery indicator
The batteries are fully
charged Prepare new batteries
There is no battery capacity.
Replace with new batteries.
There are 3 indicators for battery condition that are displayed on the LCD monitor.
Removing the battery
1. Turn off the camera power. Open the battery chamber
cover and move the battery holder aside. The battery will
be released.
2. Take out the battery and close the battery chamber cover.
: If the camera does not turn on after you have inserted batteries,
please check whether the batteries are inserted with the correct
polarity(+/-).
1. Open the battery chamber
cover by pushing in the
direction of the arrow.
2. Insert the batteries taking
note of the polarity (+ / -).
3. To close the battery
chamber cover, push it
until it clicks.
When the battery chamber cover is opened, do not press the battery chamber cover by
force. This may cause the battery chamber cover modification or breakage.
INFORMATION
17
Instructions on how to use the memory card
Be sure to format the memory card (see p.73) if you are using a newly purchased memory for
the first time, if it contains data that the camera cannot recognise, or if it contains images
captured with a different camera.
Turn off the camera power whenever the memory card is being inserted or removed.
Repeated use of the memory card will eventually reduce the memory card’s performance.
Should this be the case, you will need to purchase a new memory card.
Wear and tear on the memory card is not covered by the Samsung warranty.
The memory card is an electronic precision device.
Do not bend, drop or subject the memory card to any heavy impact.
Do not store the memory card in an environment with strong electronic or magnetic fields,
e.g. near loud speakers or TV receivers.
Please do not use or store in an environment where there are extremes in temperature.
Do not allow the memory card to become dirty or to come into contact with any liquid.
Should this happen, clean the memory card with a soft cloth.
Please keep the memory card in its case when not in use.
During and after periods of extended use, you may notice that the memory card is warm.
This is perfectly normal.
Do not use a memory card that is used in another digital camera.
To use the memory card in this camera, format first the memory card by using this camera.
Do not use a memory card formatted by another digital camera or memory card reader.
Maintenance of the memory card
Preserving the memory card data
If the memory card is subjected to any of the following, the recorded data may become
corrupted :
- When the memory card is used incorrectly.
- If the power is switched off or the memory card is removed while recording, deleting
(formatting) or reading.
Samsung cannot be held responsible for lost data.
It is advisable to copy important data onto other media as back-up e.g. floppy disks, hard
disks, CD etc.
If there is insufficient memory available : If you press the shutter button for the shot, a
[Card Full !] message will appear and the camera will not operate. To optimise the amount of
memory in the camera, replace the memory card or delete unnecessary images stored on
the memory.
18
Instructions on how to use the memory card
Don't remove the memory card when the Auto focus lamp(Green) is blinking as this may
cause damage to data in the memory card.
INFORMATION
[ SD(Secure Digital) memory card ]
Write
protect
switch
Label
Card
pins
Recorded image size TIFF S. Fine Fine Normal 30 FPS 15FPS
3072X2304 1 9 15 13 - -
2816X2112 1 10 18 26 - -
2592X1944 1 11 21 33 - -
2272X1704 2 14 26 40 - -
2048X1536 3 17 33 50 - -
1600X1200 4 30 51 75 - -
1024X768 11 60 106 129 - -
640X480 22 121 165 202 - -
640X480 - - - -
2MIN 4SEC 4MIN 1SEC
320X240 - - - -
4MIN 3SEC 7MIN 9SEC
160X128 - - - -
10MIN 10SEC 18MIN 11SEC
The camera can use SD Memory Cards and MMC (Multi Media Cards).
Please consult the enclosed manual for using the the MMC Cards.
The SD memory card has a write protect switch
that prevents image files from being deleted or
formatted.
By sliding the switch to the bottom of the SD
memory card, the data will be protected.
By sliding the switch to the top of the SD
memory card, the data protection will be
canceled. Slide the switch to the top of the SD
memory card before taking a picture.
When using a 32MB SD memory card, the specified shooting capacity will be as follows.
(These figures are intended as an indication of expected performance). These figures are
approximate as image capacities can be affected by variables such as subject matter.
Still
image
Movie
clip
19
Inserting the memory card
1. Turn off the camera’s power and pull the battery chamber
cover in the direction of the arrow to open.
2. Have the front of the memory card facing toward the front of
the camera (lens) and the card pins toward the back of the
camera (LCD monitor), and then push the memory card into
the card slot until you hear a click.
3. To close, push the battery chamber cover until you hear a
click. If the memory card does not slide in smoothly, do not
attempt to insert it by force. Check the direction of insertion,
and then insert it correctly. Do not insert the memory card the
wrong way round. Doing so may damage the memory card
slot.
1. Turn the power off using the power button.
Open the battery chamber cover and press the memory
card as shown in the image and release.
2. Remove the memory card and close the battery chamber
cover.
Removing the memory card
20
When Using the Camera for the First Time
If the camera is turned on for the first time, a menu will be displayed to set date, time and
language in the LCD monitor. This menu will not be displayed after setting up the date, time
and language. Set up the date, time and language before using this camera.
Setting up the date, time and date type
1. Select the [D & Time] menu by pressing the UP/DOWN
button and press the RIGHT button.
2. Press the UP/DOWN/LEFT/RIGHT button to select the
desired sub menu and press the OK button.
RIGHT button : Selects YEAR/ MONTH/ DAY/ HOUR /
MINUTE/DATE TYPE
LEFT button : Moves the cursor to the [D & Time]
main menu if the cursor is at the first
item of the date and time setup. In all other instances, the cursor will be
shifted to the left of its current position.
UP/ DOWN button : changes the value of each item.
You can select 18 languages. These are listed below: English, Korean, French, German,
Spanish, Italian, S. Chinese, T. Chinese, Japanese, Russian, Portuguese, Dutch, Danish,
Swedish, Finnish, Thai, BAHASA(MALAY/ INDONISIA) and Arabic.
Even if the camera is restarted, the language setting will be maintained.
INFORMATION
Setting up the language
1. Select the [Language] menu by pressing the UP/DOWN
button and press the RIGHT button.
2. Select the desired sub menu by pressing the UP/ DOWN
button and press the OK button.
Language
D & Time
ENGLISH
04/09/01
Setup
Language
D & Time
ENGLISH
04/09/01
Setup
21
LCD monitor indicator
[ Image & Full Status ]
The LCD monitor displays information about the shooting functions and selections.
No. Description Icons Page
1 Battery p.15
3 Shooting type p.27
4 Flash p.34
5 Self-timer p.36
6 Voice memo p.31
7 Macro p.32
8 Metering p.50
9 AEL
10
Manual/ Continuous auto focus
p.44
11 Sharpness p.51
12 Auto focus frame
13 Camera shake warning
14 Date/ Time 2005/01/01 01:00 PM
Recording mode2
p.12~13
22
LCD monitor indicator
Starting the recording mode
1. Insert the batteries (p.15). Insert the batteries taking
note of the polarity (+ / -).
2. Insert the memory card. (p.19)
3. Close the battery chamber cover.
4. Press the power button to turn on the camera.
(If the date/time that is displayed on the LCD monitor is
incorrect, reset the date/time before taking a picture.)
5. Select the AUTO mode by rotating the mode dial.
6. Point the camera towards the subject and compose the
image by using either the viewfinder or LCD monitor.
7. Press the shutter button to capture an image.
How to use the AUTO mode ( )
[ AUTO mode ]
If the auto focus frame turns to red when you press the shutter button down half way,
it means that the camera cannot focus on the subject. Should this be the case, the
camera is unable to capture an image clearly.
INFORMATION
15 Exposure compensation p.39
16 White Balance p.40
17 ISO p.41
18 RGB RGB
19 Image quality p.49
20 Image size p.48
Number of available shots remaining
16
Remaining time (Movie clip/ Voice recording)
00:01:30/ 01:00:00
22
Optical/ Digital Zoom bar
21
3072, 2816, 2592, 2272, 2048, 1600, 1024, 640
23
Starting the recording mode
How to use the PROGRAM mode ( )
Selecting the automatic mode will configure the camera
with optimal settings. You can still manually configure all
functions except the aperture value and shutter speed.
Steps from 1-4 are the same as those for AUTO mode.
5. Select the PROGRAM mode by rotating the mode dial.
6. Press the menu button to configure advanced functions
such as image size (p.48), quality (p.49), metering (p.50),
continuous shooting (p.51) , picture effects (p.50) and
special effects (p.51).
7. Point the camera towards the subject and compose the
image by using either the viewfinder or LCD monitor.
8. Press the shutter button to capture an image.
[ PROGRAM mode ]
[ Aperture priority mode ]
How to use the APERTURE PRIORITY mode ( )
Steps from 1-4 are the same as those for AUTO mode.
5. Select the APERTURE PRIORITY mode by rotating the
mode dial.
6. Select the desired aperture value by rotating the jog dial.
7. Point the camera towards the subject and compose the
image by using either the viewfinder or LCD monitor.
8. Press the shutter button to capture an image.
* Smaller Aperture values make the object sharp but blur
the background. Larger Aperture values make both the
object and background sharp.
24
Starting the recording mode
How to use the SHUTTER PRIORITY mode ( )
Steps from 1-4 are the same as those for AUTO mode.
5. Select the SHUTTER PRIORITY mode by rotating the
mode dial.
6. Select the desired aperture value by rotating the jog dial.
7. Point the camera towards the subject and compose the
image by using either the viewfinder or LCD monitor.
8. Press the shutter button to capture an image.
* High Shutter speeds can capture a moving object in a
still image as if the object is not moving. Low Shutter
speeds can capture a moving object with an ‘active’
effect.
[ Shutter Priority mode ]
How to use the MANUAL mode ( )
Steps from 1-4 are the same as those for AUTO mode.
5. Select the MANUAL mode by rotating the mode dial.
6. Press the ASM button to select the shutter speed or the
aperture value. Then select the desired speed or value by
rotating the jog dial.
7. Point the camera towards the subject and compose the
image by using either the viewfinder or LCD monitor.
8. Press the shutter button to capture an image.
[ Manual mode ]
25
Starting the recording mode
How to use the MySET mode ( )
This mode allows users to save frequently used shooting
settings for later use.
Steps from 1-4 are the same as those for AUTO mode.
5. Select the MySET mode by rotating the mode dial.
6. Press the menu button.
7. Use the Left/Right buttons to select the [Load Myset]
menu tap. Use the Up/Down buttons to select desired
MySET number.
8. Press the OK button to load the camera configuration
saved in the MySET number and close the menu
screen.
9. Point the camera towards the subject and compose the
image by using either the viewfinder or LCD monitor.
10. Press the shutter button to capture an image.
Please see page 52 for details of the MySET shooting
mode and menus.
[ MySET mode ]
How to use the MOVIE CLIP mode ( )
Steps from 1-4 are the same as those for AUTO mode.
5. Select the MOVIE CLIP mode by rotating the mode dial.
6. The MOVIE CLIP mode icon and available recording
time will display on the LCD monitor.
7. Point the camera towards the subject and compose
the image by using either the viewfinder or LCD monitor.
Press the shutter button and movie clips are recorded
for as long as the available recording time.
Movie clips will still be recorded if the shutter button is
released. The auto focus lamp(green) will blink during
the movie clip recording.
* If you wish to stop recording, press the shutter button
again.
* Image size and type are listed below.
- Image size : 640X480, 320X240, 160X128(Selectable)
- File type : *.avi
[ MOVIE CLIP mode ]
STANDBY
26
Starting the recording mode
Pausing while recording a movie clip (Successive Recording)
This camera allows you to temporarily stop during unwanted scenes, while recording a movie
clip. Using this function, you can record your favourite scenes into a movie clip without having
to create multiple movie clips.
Using Successive Recording
Steps from 1-6 are the same as those for MOVIE CLIP
mode.
7. Point the camera towards the subject and compose the
image by using the viewfinder or LCD monitor. Press
the shutter button and movie clips are recorded for as
long as the available recording time. Movie clips will still
be recorded if the shutter button is released.
8. Press the Pause button( ) to pause recording.
9. Press the Pause button( ) again to resume the
recording.
10. If you wish to stop recording, press the shutter button again.
00:00:04
640
[Successive recording of a movie clip]
Stop:Shutter
27
Starting the recording mode
How to use the SCENE mode ( )
Use the menu to easily configure optimal settings for a variety of shooting situations.
These include NIGHT, PORTRAIT, CHILDREN, LANDSCAPE, CLOSE UP, TEXT
RECOGNITION, SUNSET, DAWN, BACKLIGHT, FIREWORKS and BEACH & SNOW
scenes.
Steps from 1-4 are the same as those for AUTO mode.
5. Select the SCENE mode by rotating the mode dial.
6. Press the menu button and select the [Scene] menu by
pressing the left and right button.
7. Select the desired [Scene] sub menu by pressing the UP and
DOWN buttons and press the OK button. Please see page 53
for detailed descriptions for each screen.
8. The current scene icon is displayed at the top left of the
LCD.
9. Point the camera towards the subject and compose the
image by using either the viewfinder or LCD monitor.
10. Press the shutter button to capture an image.
[ SCENE mode ]
How to use the VOICE RECORDING mode ( )
1. Select the VOICE RECORDING mode by pressing the
Voice recording button twice. (In Movie clip mode, press
the Voice recording button once to select the VOICE
RECORDING mode)
2. Press the shutter button to record a voice.
- Press the shutter button once and voice is recorded for
as long as the available recording time (Max : 1 hour)
allows. The recording time will be displayed on the
LCD monitor. Voice will still be recorded if the shutter
button is released.
- If you wish to stop recording, press the shutter button
again.
- File type : *.wav
* A distance of 40cm between you and the camera
(microphone) is the best distance to record sound.
[ VOICE RECORDING mode ]
Start: Shutter
28
Things to Watch Out for When Taking Pictures
Pressing the shutter button down half way.
Lightly press the shutter button to confirm focus and flash battery charge.
Press the shutter button all way down to take the picture.
The available recording time may vary depending on shooting conditions and camera
settings.
When the Flash Off or Slow synchro mode is selected in a low lighting condition, the camera
shake warning indicator ( ) may appear on the LCD monitor. In this case, use a tripod,
support the camera on a solid surface or change the flash mode to flash shot mode.
Compensated shooting against the light :
Please do not take pictures to the sunlight direction. Taking a picture against the sun may
make the picture dark. To take a picture against the sun, please use the [Backlight] in the
scene shooting mode (see page 53), forced flash (see page 34), spot side light (see page 50),
or exposure compensation (see page 39).
Avoid obstructing the lens or the flash when you capture an image.
As there can be some differences between what is seen through the Viewfinder and the
resulting image when taken at a range closer than 1.5m, it is recommended that you use the
LCD monitor to compose these shots.
Using the LCD monitor extensively will drain the batteries.
We recommend turning off the LCD monitor and using the optical viewfinder as often as
possible in order to extend battery life.
Under certain conditions the auto focus system may not perform as expected.
- When photographing a subject that has little contrast.
- If the subject is highly reflective or shiny.
- If the subject is moving at high speed.
- When there is strong reflected light, or when the background is very bright.
- When the subject matter has only horizontal lines or the subject is very narrow
(such as a stick or flagpole).
- When the surroundings are dark.
[ Lightly press the shutter button ] [ Press the shutter button ]
29
Using the camera buttons to adjust the camera
The RECORDING (AUTO, PROGRAM, APERTURE PRIORITY, SHUTTER PRIORITY,
MANUAL, MySET, MOVIE CLIP, SCENE) mode function can be set up by using the camera
buttons.
Used for turning the camera’s power on / off.
If there is no operation during the specified time, the
camera's power will be turned off automatically to save
battery life. Refer to page 70 for more information about the
auto power off function.
Pressing the power button for over 3 seconds will deactivate
the start-up sound and sound function.
POWER button
Used for taking an image or recording voice in the
RECORDING mode.
In MOVIE CLIP mode :
Pressing the shutter button down fully starts the process for
recording a movie clip. Press the shutter button once and the
movie clip is recorded for as long as the available recording
time in the memory allows. If you wish to stop recording, press the shutter button again.
In STILL IMAGE mode
Pressing the shutter button down halfway activates the autofocus and checks the condition of
the flash. Pressing the shutter down fully takes the image and stores the relevant data
regarding the shot. If you select voice memo recording, the recording will start after the
camera has finished storing the image data.
Jog dial : Set focus distance while using the manual focusing (see page 44). Set the aperture
value and shutter speed in the A/S/M shooting mode (see page 42).
SHUTTER button/ Jog dial
If the menu is not displayed, this button works as the
OPTICAL ZOOM or DIGITAL ZOOM button.
ZOOM W/T button
30
ZOOM W/T button
This camera has a 3X optical zoom and a 10X digital zoom function. Using both will offer a
total zoom ratio of 30X.
TELE Zoom
Optical zoom TELE : Pressing the ZOOM T button. This will zoom into the subject i.e.
the subject will appear nearer.
Digital zoom TELE : When the maximum (3X) optical zoom is selected, pressing the
ZOOM T button activates the digital zoom software. Releasing
ZOOM T button stops the digital zooming at the required setting.
Once the maximum digital zoom (10X) is achieved, pressing the
ZOOM T button will have no effect.
[ WIDE zoom ] [ TELE zoom ] [ Digital zoom 5.0X ]
Pressing the
ZOOM T button
Pressing the
ZOOM T button
WIDE Zoom
Optical zoom WIDE : Pressing the ZOOM W button. This will zoom out from the subject
i.e. the subject will appear further away. Pressing the ZOOM W
button continuously will set the camera to its minimum zoom
setting i.e. the subject appears at its furthest from the camera.
Digital zoom WIDE : When the digital zoom is in operation, pressing the ZOOM W
button will reduce the digital zooming in steps. Releasing ZOOM W
button stops digital zooming. Pressing the ZOOM W button will
reduce the digital zoom and then it will continue to reduce the
optical zoom until the minimum setting is reached.
[ TELE zoom ]
[ Optical zoom 2X ]
[ WIDE zoom ]
Pressing the
ZOOM W button Pressing the
ZOOM W button
[ Digital zoom 5.0X ] [ TELE zoom ] [ WIDE zoom ]
Pressing the
ZOOM W button
Pressing the
ZOOM W button
Optical zoom
Digital zoom
31
ZOOM W/T button
To use the digital zoom the LCD monitor has to be turned on.
Images taken using the digital zoom may take a little longer for the camera to process.
Allow time for this to take place.
Only the digital zoom can be activated during the movie clip recording.
You may notice a decrease in image quality when using the digital zoom.
The digital zoom can’t be activated in the [Night], [Close up] and [Text] scene modes.
Take care not to touch the lens to avoid taking an unclear image and possibly causing
camera malfunction. If the image is dim, turn the camera power off and on again to modify
the lens position.
Take care not to press the lens as this may cause a camera malfunction.
When the camera is turned on, take care not to touch the camera's moving lens parts as
this may cause the resulting image to be dim and unclear.
Take care not to touch the lens during zoom operation as this may cause damage.
INFORMATION
32
Voice memo( ) / UP button
While the menu is showing, press the UP button to move up the submenu cursor.
When the menu is not displayed on the LCD monitor, the UP button operates as the voice
memo ( ) button. You can add your voice-over to a stored still image.
Recording a voice memo
1. Rotate the MODE DIAL to select a RECORDING mode with the exception of MOVIE CLIP
mode.
2. Press the VOICE MEMO ( ) button. If the voice memo indicator is displayed on the
LCD monitor, the setting is completed.
3. Press the shutter button and take a picture. The picture is stored on the memory card.
4. Voice memo will be recorded for ten seconds from the moment the picture is stored.
In the middle of the sound recording, pressing the shutter button will stop the voice memo.
[Recording Voice Memo]
[Preparing for Voice Memo]
A distance of 40cm between you and the camera (microphone) is the best distance to
record sound.
INFORMATION
STOP:SHUTTER
33
Available focusing method, by recording mode
(O:Selectable, X:Not selectable, :Infinity focus range)
OOOOOOOO
XOOOOOOX
OXXXX XXX
Mode
Auto
Macro
Auto macro
Mode
Auto
Macro
Auto macro
OO XX O O
XXXOOXXXXX
XXXXXXXXXX
Macro( ) / Down button (Focusing)
When the macro mode is selected, it is possible that camera shake will occur. If this is the
case, use a tripod to eliminate this.
When you take a picture within 30cm(MACRO focus), select the FLASH OFF mode.
In the AUTO mode, the Auto macro will be selected by pressing the macro button.
INFORMATION
While the menu is showing, press the DOWN button to move from the main menu to a
submenu, or to move down the submenu cursor.
When the menu is not showing, you can use the MACRO/ DOWN button to take macro
pictures (within the distance range of 4-80 cm).
[ Macro ][ Auto focus ]
Pressing the macro
button
WIDE TELE WIDE TELE WIDE TELE
80 ~ 80 ~ 4 ~ 80 25 ~ 80 4 ~ 25 ~
Unit : cm
Types of focus modes and focus ranges
Focus type
Focus range
Macro Auto macroAuto
34
Focus lock
To focus on the subject positioned outside of the centre, use the focus lock function.
Using the Focus Lock
1. Ensure the subject in the centre of the autofocus frame.
2. Press the SHUTTER button halfway. When the green auto lights up, it means the camera
is focused on the subject. Be careful not to press the SHUTTER button all the way down to
avoid taking an unwanted pictured.
3. With the SHUTTER button still pressed down only halfway, move the camera to
recompose your picture as desired, and then press the SHUTTER button completely to
take the picture. If you release your finger from the SHUTTER button, the focus lock
function will be cancelled.
[ The image to be
captured ]
[ Press the SHUTTER button ]
halfway and focus on the subject
[ Recompose the picture ]
and fully depress the
SHUTTER button
FLASH( ) / LEFT button
[ Selecting the Auto flash ]
When the menu is displayed on the LCD monitor,
pressing the LEFT button makes the cursor shift to the left
tab.
When the menu is not displayed on the LCD monitor, the
LEFT button operates as the FLASH ( ) button.
Selecting the flash mode
1. Rotate the MODE DIAL to select a RECORDING mode
with the exception of MOVIE CLIP and VOICE
RECORDING modes.
2. Press the Flash button until the desired flash mode indicator displays on the LCD monitor.
3. A flash mode indicator will be displayed on the LCD monitor. Use the correct flash to suit
the environment.
35
FLASH( ) / LEFT button
Unit : m
Flash range
Using the flash frequently will reduce the life of the batteries.
Under normal operating conditions the charging time for the flash is normally within 7
seconds. If the batteries are weak, the charging time will be longer.
During the continuous shot, movie clip mode, the flash function will not operate.
Take photographs within the flash range.
The image quality is not guaranteed if the subject is too close or highly reflective.
The LCD monitor is turned off for a while after using the flash to recharge it.
INFORMATION
WIDE TELE WIDE TELE WIDE TELE
0.8~3.0 0.8~2.0 0.2~0.8 0.25~0.8 0.2~3.0 0.25~2.0
ISO
AUTO
MACRO AUTO MACROAUTOFOCUS
36
FLASH( ) / LEFT button
Icon Flash mode Description
Flash mode indicator
If the subject or background is dark, the camera flash will operate
automatically.
Auto flash
Auto &
Red eye
reduction
Fill in flash
Slow synchro
Flash off
If a subject or background is dark, the camera flash will work
automatically and will reduce the red-eye effect by using the red-eye
reduction function.
The flash will operate in conjunction with a slow shutter speed in
order to obtain the correct exposure. We recommend using a tripod
for this function. When you take an image in a condition with poor
light, the camera shake warning indicator ( ) will display on the
LCD monitor.
The flash fires regardless of available light.
The intensity of the flash will be controlled, according to the
prevailing conditions. The brighter the background or subject is, the
less intense the flash will be.
The flash does not fire. Select this mode when capturing images in a
place or situation where flash photography is prohibited. When you
capture an image in a poorly lit condition, the camera shake warning
indicator ( ) will display on the LCD monitor.
Available flash mode, by recording mode
XOX XXOXXXXXXXXXXO
OOXXXOXOOXXXXX XXX
XOOOOOXXXXXXXXOXX
XOOOOOOXXXXXXX XXX
OOOOOOOOOOOOOO XOX
37
Self-timer( ) / Remote ( )/ Right button
When the menu is displayed on the LCD monitor, pressing the Right button makes the cursor
shift to the right tab. The right button can also be used to move to a sub menu to select a
different setting.
When the menu is not displayed on the LCD monitor, the RIGHT button operates as the Self-
timer ( ) and Remote ( ) button. This function is used when the photographer would
also like to be in the image.
Using the self-timer and remote control.
1. Rotate the mode dial to the RECORDING mode.
2. Press the SELF-TIMER button until the desired mode indicator displays on the LCD
monitor. A self-timer icon or remote control icon appears on the LCD monitor.
- Selecting a self-timer : When you press the SHUTTER button, the picture will be
taken after the specified time has elapsed and the self-timer
function will be canceled.
- Selecting a remote mode : Pressing the shutter button of remote control will allow an
interval of 2 seconds before the image is taken. In the remote
mode, the shutter button of the camera can’t be activated. After
taking a picture, the remote mode will be maintained. But,
pressing the power button, rotating the mode dial, pressing the
play mode button and pressing the self-timer button will cancel
the remote mode.
[Selecting the 2 SEC self-timer] [Selecting the remote control]
Description of Self-timer/Remote mode
Icon Mode Description
Pressing the shutter button will allow an interval of 2 seconds
before the image is taken.
Pressing the shutter button will allow an interval of 10 seconds
before the image is taken.
A picture will be taken after about 10 seconds and 2 seconds
later a second picture will be taken.
You can take a picture by remote control instead of using the
shutter button of the camera.
Double
Remote
mode
2s
10s
38
Self-timer( ) / Remote ( )/ Right button
Self-timer/ remote mode setting
Remote control range
When you take a picture by using the remote control, refer
to the illustrations shown alongside about the remote
control range.
Off 2s self-timer 10s self-timer
Double self-timer Remote
Off 10s self-timer Remote
Mode dial
AUTO
PROGRAM
A/S/M, MySET
SCENE
MOVIE CLIP
[ Shutter button on the
remote control ]
When taking a picture using the self-timer, the self-timer lamp works as follows:
2 second self-timer setting : The self-timer lamp blinks at 0.25 second interval for 2
seconds.
10 second self-timer setting : The self-timer lamp blinks at 1 second interval for the first 7
seconds. It blinks at 0.25 second interval for the remaining
3 seconds.
If you operate the Mode dial and Self-timer button during the self-timer operation, the self-
timer function is canceled.
Use a tripod to prevent the camera from shaking.
In Movie Clip mode, only the 10s self-timer and remote will work.
INFORMATION
Setting ( marked camera working mode is the default setting.)
39
Self-timer( ) / Remote ( )/ Right button
Replacing batteries for the remote control
MENU/ OK button
Make sure the + polarity is toward the top and the polarity is toward the bottom while
installing batteries for the remote control. Replace batteries for the remote control in the local
service centre. Use the CR 2025 3V batteries.
If the menu is displayed, use the 5-Function buttons to change the data values and for your
changes to be accepted
If the menu is not displayed, press the MENU/OK button to display a menu for the current
camera mode on the LCD monitor. Press the button again to return to the previous state.
- There is no menu for VOICE RECORDING mode.
- The menu screen may not show on the LCD when another button is pressed or image data
is being processed. (The green lamp next to the view finder blinks)
- When the menu is showing on the LCD monitor, it is not possible to operate the shutter
button i.e. capture an image. To capture an image, simply cancel the menu display by
pressing the MENU button.
[ Menu on ]
[ Menu off ]
Pressing
the MENU
button
3072X2304
2816X2112
2592X1944
2272X1704
3072
Size
40
+/- button
RGB : Allows the user to adjust the R (Red), G (Green), and B (Blue) values of the images to
be captured.
Setting RGB Values
1. Press the +/- button, and then use the UP and DOWN
buttons to select the RGB icon ( ).
The RGB menu bar will appear as shown.
2. Use the UP/ DOWN/ LEFT and RIGHT buttons to select
the desired RGB value.
- Up/Down Button: Navigates between R, G, and B
icons.
- Left/Right Button: Changes value of each icon.
3. When you press the +/- button again, the value you set will be saved and RGB setup
mode will end.
You can use the +/- button to adjust the values for the RGB, ISO, white balance and
exposure compensation.
Main menu Sub menu Available camera mode
RGB
-2.0~0.0~+2.0(1/3EV steps)Exposure compensation
ISO
WHITE BALANCE
R (Red), G (Green), B (Blue)
AUTO, DAYLIGHT, CLOUDY, FLUORESCENT H,
FLUORESCENT L, TUNGSTEN, CUSTOM.
AUTO, 50, 100, 200, 400
41
+/- button
Selecting an ISO Sensitivity
1. Press the +/- button, and then use the UP and DOWN
buttons to select the ISO icon( ). The ISO menu bar
will appear as shown.
2. Use the LEFT and RIGHT buttons to select the desired
ISO sensitivity value.
- AUTO : The camera's sensitivity is automatically
changed by variables such as lighting value or subject brightness.
- 50, 100, 200, 400 : You can increase the shutter speed while the same amount of light is
present, by increasing the ISO sensitivity. However, the image may be saturated in high
luminance. The higher the ISO value, the higher the camera’s sensitivity to light is and
therefore the greater its capacity to take pictures in dark conditions. However, the noise
level in the image will increase as the ISO value increases, making the image appear
coarse.
3. When you press the +/- button again, the value you set will be saved and ISO setup mode
will end.
White balance : The white balance control allows you to adjust the colours to appear more
natural looking.
Selecting a White Balance
1. Press the +/- button, and then use the UP and DOWN
buttons to select the white balance icon ( ).
The white balance menu bar will appear as shown.
2. Use the LEFT and RIGHT buttons to set the white
balance to the desired value. The value you set will be
displayed on the LCD monitor.
AUTO : The camera automatically
selects the appropriate white
balance settings, depending on the prevailing lighting conditions.
DAYLIGHT : For taking images outside.
CLOUDY : For taking images under a cloudy and overcast sky.
Fluorescent H : For shooting under daylight fluorescent types of three-way
fluorescent lighting.
Fluorescent L : Shooting under white fluorescent lighting.
TUNGSTEN : For shooting under tungsten (standard light bulb) lighting.
CUSTOM : Allows the user to set the white balance according to the shooting
condition.
Different lighting conditions may cause a colour cast on your images.
3. Press the +/- button again. The value you set will be saved and White Balance setup mode
will end.
ISO: You can select the ISO sensitivity when taking pictures.
The speed or specific light-sensitivity of a camera is rated by ISO numbers.
42
+/- button
Using the Custom White Balance
White balance settings may vary slightly depending on the shooting environment. You can
select the most appropriate white balance setting for a given shooting environment by setting
up the custom white balance.
1. Select the CUSTOM ( ) menu of the White Balance.
You can select CUSTOM 1 or CUSTOM 2 white
balance.
2. Place a sheet of white paper in front of the camera so
that the LCD monitor shows only white, and then press
the SHUTTER button.
3. The value you set will be saved.
- The custom white balance value will be applied, starting
with the next picture you take.
- The user configured white balance will remain effective
until it is overwritten.
[White paper]
MEASURE : SHUTTER
Exposure compensation : This camera automatically adjusts the exposure according to the
ambient lighting conditions.
You can also select the exposure value by using the +/- button.
Compensating Exposure
1. Press the +/- button, and then use the UP and DOWN
buttons to select the exposure compensation icon ( ).
The exposure compensation menu bar will appear as
shown.
2. Use the LEFT and RIGHT buttons to set the desired
exposure compensation factor.
3. Press the +/- button again. The value you set will be
saved and the Exposure Compensation setup mode will close. If you change the exposure
value, the exposure indicator ( ) will be displayed on the bottom of the LCD monitor.
* A negative exposure compensation value reduces the exposure.
Note that a positive exposure compensation value increases the exposure and the LCD
monitor will appear white or you may not get good pictures.
43
You can use the ASM button to select the Aperture Value and Shutter speed in the Manual mode.
AEL/ASM button
The camera measures brightness of the object and automatically set the best exposure
value. If difference between the exposure values of the object and background is too great,
use the AEL button to manually set the exposure value against sunlight or in strong light.
This button is available in the PROGRAM, Aperture priority(A), Shutter priority(S), MySET
and MOVIE CLIP mode.
Use the automatic exposure lock.
1. Ensure the subject in the centre of the autofocus frame.
2. Move the camera to point the automatic focus mark on the object of desired exposure.
3. Press the AEL button to lock the exposure and display the AEL icon in the bottom of the
LCD.
4. Focus the camera again and press the shutter button again for shooting.
[ Screen for shooting ] [ Focus to the object and ]
press the AEL button
[ Refocus and fully press ]
the shutter button
Using the ASM button in the M mode
1. Rotate the MODE DIAL to select the M mode.
2. Press the ASM button and the aperture value and
shutter speed are displayed. To select the aperture
value or shutter speed, press the ASM button.
The selected item is then highlighted in red.
3. Rotate the jog dial to select the aperture value and
shutter speed. Press the SHUTTER button to take the
picture.
In the Manual mode, the exposure information will be displayed by pressing the shutter
button down halfway.
44
MF button
Use this button to select the focusing method. Repeatedly press the MF button to rotate [Manual
focusing] [Continuous automatic focusing] [Automatic focusing].
Automatic focusing : Slightly press the shutter to let the camera measure distance to the
object and select the best focusing.
If successfully focused with the slight press of the shutter, the automatic
focusing mark is turned green.
Manual focusing : Where the automatic focusing is not available, for example, in very dark
conditions, use the manual focus. Please be careful when using the
manual focus as the picture can be blurred easily.
Focus distance of 0.04~0.3m are only supported in the Wide zoom.
The flash is fixed as not available.
The focus value displayed in the LCD while manually focusing is measured from the end
of the lens
INFORMATION
Long distance
Close-up
Manual focusing.
1. Press the MF button to display the MF bar.
The MF icon is displayed in the bottom of the LCD.
2. Use the jog dial to set the focus distance.
Turn to the left : Move the focus farther.
Turn to the right : Move the focus closer.
45
LCD button
[Image & full information]
[Image & basic information]
[Histogram] [LCD off]
You can check the recording status in the LCD monitor. In any mode
with the exception of VOICE RECORDING mode, pressing the LCD
button will change the display as shown below.
If the LCD monitor is turned off, the mode dial lamp will light up.
Histogram
Shows you the distribution of brightness in recorded
images. If the bars in the histogram are higher towards the
right, the image may be too bright. If the bars are higher on
the left, the image may be too dark. If the lighting
conditions are too bright to check the subject by using the
LCD monitor, checking the histogram will enable more
precise exposure control for the shots.
Pressing
the LCD
button
Pressing
the LCD
button
Pressing
the LCD
button
Pressing the LCD button
Pixel
Dark Bright
Distribution of brightness
46 46
Using the LCD monitor to adjust the camera settings
The following functions are available, depending on the mode you have selected.
The items indicated by are default settings.
You can use the menu on the LCD monitor to set up recording functions. In any mode with
the exception of VOICE RECORDING mode, pressing the MENU button displays the menu
on the LCD monitor.
The menu will not be displayed on the LCD monitor in the following circumstances:
- When another button is being operated.
- While image data is being processed.
(when the green lamp next to the viewfinder blinks)
- When there is no battery capacity.
When the menu is showing on the LCD monitor, it is not possible to operate the shutter
button i.e. capture an image. To capture an image, simply cancel the menu display by
pressing the MENU button.
INFORMATION
Onglet de menu Menu principal Sous-menu
Mode apprareil en fonction
Page
3072X2304
2816X2112
2592X1944
2272X1704
2048X1536
1600X1200
1024X768
640X480
640X480
320X240
160x128
30 FPS
15 FPS
Frame Rate p.49
p.48
p.48
Size
47
Using the LCD monitor to adjust the camera settings
Onglet de menu Menu principal Sous-menu
Mode apprareil en fonction
Page
TIFF
S. Fine
Fine
Normal
Multi
Spot
Single
Continuous
AEB
AFB
Soft
Normal
Vivid
Normal
B & W
Sepia
Negative
Off
Range 1
Range 2
Range 3
Off
2 Parts
3 Parts
4 Parts
Off
Frame1
Frame2
Frame3
p.49
Quality p.49
Metering
Shooting p.51
Effect p.50
Special Effect
p.50
p.50
Sharpness p.51
HighLight
Photo
Frame
Composite
48
Using the LCD monitor to adjust the camera settings
* Menus are subject to change without prior notice.
Onglet de menu Menu principal Sous-menu
Mode apprareil en fonction
Page
MYSET1
MYSET2
MYSET3
MYSET1
MYSET2
MYSET3
Off
On
Load Myset
Scene
p.52
p.52
p.53
Stabilizer
Save Myset
Night, Portrait, Children,
Landscape, Close up,
Text, Sunset, Dawn,
Backlight,
Firework,
Beach&Snow
49
How to use the menu
3. Use the UP and DOWN buttons to select a sub menu.
4. Select a sub menu, and then press the OK button. The value you set will be saved and the
menu will disappear.
1. Turn on the camera and press the MENU button. A menu for each camera mode appears.
However, there is no menu for Voice Recording mode ( ).
2. Use the LEFT and RIGHT buttons to navigate through the menus.
Press the LEFT
or RIGHT button.
Press the LEFT
or RIGHT button.
Press the UP or
DOWN button.
Press the UP or
DOWN button.
You can select the image size appropriate for your application.
Mode
Icon
3072 2816 2592 2272 2048 1600 1024 640 640 320 160
Size
3072X2304 2816X2112 2592X1944 2272X1704 2048X1536 1600X1200 1024X768 640X480 640X480 320X240 160X128
STILL IMAGE mode
MOVIE CLIP mode
The higher the resolution, the lower the number of available shots will be because high
resolution images require more memory than lower resolution images.
INFORMATION
Size
Metering
Multi
Spot
3027
Shooting
Single
Continuous
AEB
AFB
Effect
Normal
B & W
Sepia
Negative
NOR
[ PROGRAM mode ]
Size
3072X2304
2816X2112
2592X1944
2272X1704
3072
[ MOVIE CLIP mode ]
Size
640X480
320X240
160X128
320
30FPS
Effect Effect
Normal
B & W
Sepia
Negative
Normal
B & W
Sepia
Negative
NOR
Quality
TIFF
S.Fine
Fine
Normal
3072
50
Quality
You can select the compression ratio appropriate for your
application of the captured images. The higher the
compression ratio, the lower the picture quality.
Mode
Icon
TIFF
Sub menu
TIFF
S. Fine Fine Normal
30FPS 15FPS
File Format
tif jpeg jpeg jpeg avi avi
STILL IMAGE mode MOVIE CLIP mode
TIFF is the highest quality and NORMAL is the lowest setting.
Choose the setting appropriate for your needs.
The TIFF file format is for professionals and provides the best quality.
However, large file size reduces number of available pictures to take and increases
saving time to the memory card.
[Please Wait !] message is displayed while saving a TIFF file to the memory card.
If you select the TIFF file format, the double self-timer can’t be selected.
This file format complies with the DCF(Design rule for Camera File system).
JPEG (Joint Photographic Experts Group): JPEG is the image compression standard
developed by the Joint Photographic Experts Group. This type of compression is most
commonly used for compressing photos and graphics because it can compress the files
efficiently without damaging the data.
INFORMATION
[ PROGRAM mode ]
Quality
TIFF
S.Fine
Fine
Normal
3072
51
Metering
If you cannot obtain suitable exposure conditions, you can change the metering method to
take brighter pictures.
Multi ( ) : Exposure will be calculated based on
an average of the available light in the
image area.
However, the calculation will be biased
towards the centre of the image area.
This is suitable for general use.
Spot ( ) : Only the rectangular area in the centre
of the LCD monitor will be metered for
light. This is suitable when the subject in the centre is exposed correctly,
regardless of the back lighting.
[ PROGRAM mode ]
Metering
Multi
Spot
3072
52
Continuous shot
You can select continuous shot, AEB (Auto Exposure Bracketing) and AFB (Auto Focus
Bracketing). If you select CONTINUOUS, AEB or AFB, the flash will automatically be set to
Flash Off.
[Single]:
Take one picture only
[Continuous]:
Images will be taken continuously until the shutter button is
released. The shooting capacity depends on the memory.
If less than 3 pictures are available in the memory, the Sequential and the AEB shooting
are not available.
If you select 3072X2304 or 2816X2112 image size, the maximum numbers of continuous
shot are 3.
It is best to use a triangular support for the AEB shooting for saving time is long and hand
shaking may occur.
If you selected the TIFF image format, you can t select the [Continuous], [AEB] and [AFB]
menu.
If you select the [S.Fine] image quality, you can’t select the [Continuous] menu.
The self-timer can’t be activated during the continuous shooting.
INFORMATION
[ PROGRAM mode ]
Shooting
Single
Continuous
AEB
AFB
[AEB]:
You can select the exposure bracket range( 0.3EV step,
6 steps) by rotating the jog dial. Three pictures are taken in
a series in different exposure value. Use this menu if it is
hard to decide exposure of the object.
[AFB]:
You can select the focus bracket range( 1 step, 3 steps)
by rotating the jog dial. Three pictures are taken in a series
in different focus range. Use this menu if it is hard to
decide distance of the object.
NOR
Shooting
NOR
Shooting
NOR
Single
Continuous
AEB
AFB
Single
Continuous
AEB
AFB
53
Sharpness
By using the camera's digital processor, it is possible to add special effects to your images.
Normal : No effect is added to the image.
B & W : Converts the image to black and white.
Sepia : Captured images will be stored in a sepia tone (a gradient of yellowish brown
colours).
Negative : Save the image in negative mode.
Effect
You can adjust the sharpness of the picture you want to take.
You cannot check the sharpness effect on the LCD monitor
before you take a picture, because this function is applied
only when the captured image is stored on the memory.
[ PROGRAM mode ]
Sharpness
Soft
Normal
Vivid
[ PROGRAM mode ] [ MOVIE CLIP mode ]
Effect
Normal
B & W
Sepia
Negative
NOR
NOR
Sub menu Icon Description
Vivid
Normal
Soft
The edges of the image are softened.
This effect is suitable for editing images on your PC.
The edges of the image are sharp.
This is suitable for printing.
The edges of the image are emphasized. The edges will appear
sharp, but noise may occur in the recorded image.
Effect
Normal
B & W
Sepia
Negative
NOR
30FPS
54
Special Effect
By using the camera s digital processor, it is possible to add special effects to your images.
You can select this menu only in the PROGRAM, MySET, Aperture priority, Shutter priority
and MANUAL modes.
You can select this menu only in the 2592x1944, 2272x1704, 2048x1536, 1600x1200,
1024x768, 640x480 image size.
You can select the preset focus frame, Part shot and Photo frame function. If a special effect
is selected, the rest special functions set before are canceled automatically.
You can make the subject stand out from its surroundings. The subject will be sharp and in
focus while making the rest out of focus.
1. Select the PROGRAM, MySET, Aperture priority, Shutter
priority or MANUAL modes. Then press the menu button.
2. Press the LEFT/ RIGHT button and select the [Special
Effect] menu tab.
3. Select the [Out Focus] menu by pressing the UP/ DOWN
button and press the Right button.
4. Select a desired sub menu by pressing the UP/ DOWN
button and press the OK button.
- [Cancel] : The preset focus frame will not be added.
Special Effect : Preset focus frames
5. Press the menu button twice and the menu will disappear.
6. When you press the Shutter button half-way, autofocus
will be performed and the preset focus frame area will
appear simultaneously.
[Range 1] [Range 2] [Range 3]
Special Effect
HighLight
Composite
Photo Frame
Off
Off
Off
NOR
Move : Change:
55
Special Effect : Part shot
[The result image][1/2] [2/2]
You can combine 2~4 different shots in a still image.
1. Select the PROGRAM, MySET, Aperture priority, Shutter priority or MANUAL modes.
Then press the menu button.
2. Press the LEFT/ RIGHT button and select the [Special
Effect] menu tab.
3. Select the [Part Shot] menu by pressing the UP/ DOWN
button and press the Right button.
4. Select a desired sub menu by pressing the UP/ DOWN
button and press the OK button.
- [Off] : cancels the part shot
- [2 Parts] : 2 different shots are combined in a still image.
- [3 Parts] : 3 different shots are combined in a still image.
- [4 Parts] : 4 different shots are combined in a still image.
5. Press the menu button twice and the menu will disappear.
6. The number of frames you selected in step 4 is displayed on the LCD monitor.
Press the shutter button to start the Part shot.
Pressing the
shutter button
Pressing the
shutter button
Selecting 2 Parts shot
Special Effect
HighLight
Composite
Photo Frame
Off
Off
Off
NOR
Move : Change:
You can use the flash button, self-timer button, macro button, +/- button and the Zoom
W/T button during the composite shots.
If you change the image size, press the camera buttons (Play mode button , Voice menu(UP)
button) or rotate the mode dial during the composite shots, the captured images aren’t saved
and the first step of the composite shot will display on the LCD monitor. Do not press the
camera buttons or rotate the mode switch during the composite shots.
To insert the voice memo, press the voice memo button before starting the composite
shot. The voice memo will start after taking the last composite shot.
If you select [Cancel] in the [Composite] menu, the composite shot will be cancelled.
INFORMATION
56
Special Effect : Photo Frame
You can add 3 types of frame-like borders to a still image you want to capture.
[Frame 1] [Frame 2] [Frame 3]
1. Select the PROGRAM, MySET, Aperture priority,
Shutter priority or MANUAL modes. Then press the
menu button.
2. Press the LEFT/ RIGHT button and select the [Special
Effect] menu tab.
3. Select the [Photo Frame] menu by pressing the UP/
DOWN button and press the Right button.
4. Select a desired sub menu by pressing the UP/ DOWN
button and press the OK button.
- [Cancel] : The photo frame will not be added.
5. Press the menu button twice and the menu will
disappear. If you select the [Frame 1~3] menu, the
preset focus frame area will appear.
* You can check the photo frame you added to pictures
in Quick View or Play mode.
Special Effect
HighLight
Composite
Photo Frame
Off
Off
Off
NOR
Move : Change:
57
Save / Load a specific camera configuration (MySET)
Use the MySET mode to save frequently used camera settings (Save Myset) and use it later
(Load Myset)
Saving the camera configuration : Available in the PROGRAM, A, S and M shooting mode.
1. Use the camera buttons and menu to set desired camera configuration.
2. Press the menu button in any mode except AUTO,
VOICE RECORDING, MOVIE CLIP, SCENE and MySET
mode.
3. Press the Left/Right buttons to select the [Save Myset]
menu tap.
4. Press the Up/Down buttons to select desired MySET slot
number to save.
5. Press the OK button to save the current configuration in
the selected MySET slot and close the menu.
Loading the saved camera configuration: available in the MySET shooting mode.
1. Turn the mode dial to select the MySET shooting mode
and press the menu button.
2. Press the Left/Right buttons to select the [Load Myset]
menu tap.
3. Press the Up/Down buttons to select a MySET slot
number to load.
4. Press the OK button to set the camera configuration as
saved in the MySET slot.
* The current MySET slot number is displayed in the top left of the LCD.
Saving is available for the following camera functions.
Functions using the camera buttons - Macro, flash, white balance, ISO, Aperture value
and Shutter speed.
Functions using the menu screen - Size, quality, metering, effect, sharpness and
continuous shot.
INFORMATION
[ PROGRAM mode ]
[ MySET mode ]
Save Myset
Myset 1
Myset 2
Myset 3
NOR
Load Myset
Myset 1
Myset 2
Myset 3
3072
58
Scene
Sub menu Icon Description
Children
Landscape
Close up
Sunset
Dawn
Backlight
Firework
Beach&Snow
Select the [Scene] submenu to automatically configure
optimal settings, depending on the selected scene. Only
available in the SCENE Mode.
To take a still picture of moving children
Portrait To take a picture of a person
Night Use this for shooting still images at night or in other dark conditions.
Close-up shooting for small objects such as plants and insects
For taking pictures of sunsets
Scenery with green woods or blue sky
Daybreak scenes
Portrait without shadows caused by backlight
Firework scenes
Text Use this mode to shoot a document
For ocean, lake, beach and snowscape scenes
[SCENE mode]
When the close-up, sunset, dawn, fireworks are selected, it is possible that camera shake
will occur. If this is the case, use a tripod to eliminate this.
In the [Children] and [Close up] scene mode, the Continuous Automatic Focusing (CAF)
function will be activated and the CAF icon is displayed at the bottom of the LCD monitor.
Continuous automatic focusing : The camera keeps focusing while the object is moving
even if the shutter button is not slightly pressed. Note that using the Continuous automatic
focusing uses more battery than the Automatic focusing does.
INFORMATION
Scene
Night
Portrait
Children
Landscape
3072
59
Movie Clip frame stabiliser
This function helps stabilize images captured during movie recording.
You can select this menu only in the MOVIE CLIP mode.
How to use this function
1. Select the MOVIE CLIP mode by sliding the mode switch
and press the menu button. Select the [Stabilizer] menu
and press the right button.
2. Select a desired sub menu by pressing the Up/Down
button and press the OK button.
[On] : Prevents camera shake during movie recording.
The recording frame range will become narrower
than when you select the [Off] menu.
Pre-view frames may not display smoothly on the LCD monitor, but stored movie
clips have no problems.
[Off] : Movie clip frame stabilizer function becomes disabled.
Stabilizer
Off
On
NOR
60
Starting play mode
Turn the camera on and select Play mode by pressing the play mode button ( ).
The camera can now play back the images stored in the memory.
If you have turned on the camera by pressing the POWER button, you can press the PLAY
MODE button once to switch to Play mode and press it again to switch to Recording mode.
You can turn the power on with the play mode button. The camera is turned on in play mode.
Press the play mode button again to turn off the camera. Switch the mode dial to change to
another shooting mode while the camera is on.
You can set up the PLAY mode function by using the camera buttons and LCD monitor.
If you press the PLAY button to switch to Play mode, the camera lens will retract into the
camera body for protection of the lens after about 10 seconds.
Playing back a still image
1. Select the PLAY mode by pressing the play
mode button ( ).
2. The last image stored on the memory is
displayed on the LCD monitor.
3. Select an image that you want to view by
pressing the LEFT / RIGHT button.
Press and hold the LEFT or RIGHT button to
play back the images quickly.
Manner mode : Pressing the power button for more than 3 seconds changes the buzzer
and start-up sound setting to OFF, even though you may have set these to ON.
Even if the camera’s power is off, you can start the play mode by pressing the play mode
button.
INFORMATION
61
Starting play mode
Playing back a movie clip
Steps from 1-2 are the same as those to play back a still image.
3. Select the recorded movie clip that you want to play back
by using the LEFT/RIGHT button. If you select a movie
clip, the movie clip indicator ( ) will be displayed on
the LCD monitor.
4. Press the play & pause button ( ) to play back a
movie clip file.
- To pause a movie clip file while playing it back, press
the play & pause button again.
- Pressing the play & pause button again will cause the
movie clip file will restart.
- To rewind the movie clip while it is playing, press the
LEFT button. To fast forward the movie clip, press the
RIGHT button.
- To stop playback of the movie clip, press the play &
pause button, and then press the LEFT or RIGHT button.
How to capture the movie clip
Steps 1-2 are the same as those for playing back a still
image.
3. Select the recorded movie clip that you want to play
back by using the LEFT/RIGHT button.
4. Press the Play/Pause button to play the movie clip
5. Press the Play/Pause button while playing the movie
clip. Then press the Shutter button.
6. The paused movie clip is saved in a new file name.
* The captured movie clip file has same size as the original
movie clip (640X480, 320X240, 160X128).
Movie clip capture function: capture still images from the movie clip.
[ Paused ]
[ Press the shutter button ]
9
PLAY
REW FF
Trim:T Capture:SH
62
Starting play mode
On camera movie trimming : You can extract desired frames of movie clip during the movie
clip play back.
1. Select a desired movie clip in the play mode.
2. Play back the movie clip by pressing the Play &
Pause button.
3. Press the Pause button at the point of the movie clip
that you want to start extracting.
4. Press the T button. (The start point. Doesn t display
on the status bar, but the start point will be marked.)
5. Press the Play button and the extracted range will be
displayed on the status bar.
6. At the point of movie clip that you want to stop
extracting, press the Pause button.
7. Press the T button and a confirmation window will
display.
8. Select a desired sub menu by pressing the UP/
DOWN button and press the OK button.
[Trimming] : The extracted frames are saved as a
new file name.
[Cancel] : The movie trimming will cancel.
If the running time is under 10 seconds, the movie clip can t be trimmed.
If you want to extract the movie clip at the beginning of the frame, press the Zoom T
button before starting the movie clip.
If the time line bar passes by the start point by pressing the REW button, the first frame of
the movie clip will display.
If you doesn t specify the ending point of the movie clip, the trimming confirmation
window will display at the point of the last frame.
INFORMATION
9
PLAY
REW FF
Trim:T Capture:SH
9
PLAY
REW FF
Trim:T
9
PLAY
REW FF
Trimming?
Trimming
Cancel
Confirm : OK
63
Starting play mode
Playing back a recorded voice
Steps from 1-2 are the same as those to play back a still
image.
3. Select the recorded voice that you want to play back by
using the LEFT/RIGHT button. If you select a recorded
voice file, the voice indicator ( ) will be displayed on
the LCD monitor.
4. Press the play & pause button ( ) to play back a
recorded voice file.
- To pause a recorded voice file, while playing it back,
press the play & pause button again.
- To resume playback of the voice file, press the play & pause button.
- To rewind the voice file while it is playing, press the LEFT button.
To fast forward the voice file, press the RIGHT button.
- To stop playback of the voice file, press the play & pause button, and then press the
LEFT or RIGHT button.
3
PLAY
64
LCD monitor indicator
The LCD monitor displays information about the shooting conditions.
Size : 3072X2304 Size
Av : F2.8 Aperture value
Tv : 1/60 Shutter speed
ISO : 75 ISO sensitivity
Flash : Off Whether or not the
flash is used.
Date : 2005/01/01 Recording date
Size : 3072X2304
Av : F2.8
Tv : 1/60
ISO : 75
Flash : Off
Date : 2005/01/01
If you press the LCD button, you can check the following recording information:
No. Description Icon Page
1 Battery p.16
2 Play mode
3 File Type
4 Voice memo p.60
5 Protect indicator p.67
6 DPOF indicator p.70
7 Stored image number 9
8 TIFF file
65
Using the camera buttons to adjust the camera
In Play mode, you can use the buttons on the camera to conveniently set up the Play mode
functions.
Image enlargement
1. Select an image that you want to enlarge and press the enlargement button.
2. Different parts of the image can be viewed by pressing
the 5 function button.
3. Pressing the thumbnail button will zoom back to the
original full sized image.
- You can tell whether the image displayed is an
enlarged view by checking the image enlargement
indicator shown at the bottom left of the LCD monitor.
(If the image is not an enlarged view, the indicator will
not be displayed.) You can also check the area of
enlargement.
- Movie clips and WAV files can’t be enlarged.
- If an image is enlarged, a loss of quality may occur.
Thumbnail ( ) / Enlargement ( ) button
You can view multiple pictures, enlarge a selected picture, and crop and save a selected area
of an image.
Thumbnail display
1. While an image is displayed full screen, press the
thumbnail button.
2. The thumbnail display will highlight the image that had
been showing at the time the thumbnail mode was
selected.
3. Press the 5 function button to move to a desired image.
4. To view an image separately, press the enlargement
button ( ).
[ Normal display mode ] [ Thumbnail display mode ]
Pressing the thumbnail
button ( )
Pressing the enlargement
button ( )
Highlighted image
66
Thumbnail( ) / Enlargement( ) button
The maximum enlargement rate in proportion to the image size.
Trimming : You can extract part of the image that you want
and save it separately.
1. Select an image that you want to enlarge and press the
enlargement button.
2. Different parts of the image can be viewed by pressing
the 5 function button.
3. Press the MENU button and a message will be
displayed as shown alongside.
4. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button.
- [Trim] :
The trimmed image will save as a new file name, and display on the LCD monitor.
- [Cancel] : The trimming menu will disappear.
* If there is little memory space to save the trimmed image, the image can’t be trimmed.
* To delete the enlarged image during the trimming function, press the delete button.
Image size 3072 2816 2592 2272 2048 1600 1024 640
Maximum enlargement rate
X12.0 X11.0 X10.1 X8.8 X8.0 X6.2 X4.0 X2.5
Voice ( ) memo / Up button
When the menu is displayed on the LCD monitor, pressing the UP button makes the menu
cursor move up.
When the menu is not displayed on the LCD monitor, the UP button operates as the voice
memo button. You can add your voice to a stored still image.
Adding a Voice Memo to a Still Image
1. Press the LEFT/ RIGHT button to select an image that
you wish to add sound to.
2. Press the voice memo button ( ) and the voice memo
indicator will display. The camera is now ready to record
a voice memo.
Trimming?
Trim:OK
Cancel
Confirm:OK
Start:Shutter
67
Voice ( ) memo / Up button
3. Press the shutter button to start recording and voice will
be recorded to the still image for 10 seconds.
While the voice is recording, the recording status
window will be displayed as shown alongside.
4. The recording can be stopped by pressing the shutter
button again.
5. The ( ) icon will be displayed on the LCD monitor
after voice memo recording has finished.
- Voice memos can’t be recorded onto movie clip files.
- A distance of 40cm between you and the camera
(microphone) is the best distance to record sound.
- The voice memo will be saved in *.wav format, but has
the same file name as the still image to which it
corresponds.
- If you add a new voice memo to the still image that
already has a voice memo, the existing voice memo will be erased.
Play & Pause ( )/ Down button
In Play mode, the play & pause/ down button works as follows:
- If the menu is displayed
Press the DOWN button to move from the main menu to a sub menu, or to move down the
sub menu cursor.
- If a still image with a voice memo, a voice file, or a movie clip is playing
In Stop mode : Plays a still image with a voice memo, a voice file, or a movie clip.
During playback : Temporarily stops playback.
In Pause mode : Resumes playback
Stop:Shutter
[ Voice recording is stopped ]
3
[ Voice recording is paused ][ Voice recording is playing ]
3
3
PLAY
PAUSE
PLAY
68
LEFT/ RIGHT/ MENU/ OK button
LEFT / RIGHT/ MENU/ OK buttons activate the following.
- LEFT button : While the menu is showing, press the LEFT button to select the menu
tab to the left of the cursor.
- RIGHT button : While the menu is showing, press the RIGHT button to select the menu
tab to the right of the cursor, or to move an secondary menu.
- MENU button : When you press the MENU button, the play mode menu will be
displayed on the LCD monitor. Pressing it again will return the LCD to
the initial display.
- OK button : When the menu is displayed on the LCD monitor, the OK button is used
for confirming data that is changed by using the 5 function button.
The shooting information will be displayed on the LCD monitor.
The last image stored in the memory is displayed on the
LCD monitor by pressing the play mode button.
Pressing the LCD( ) button in the PLAY mode will
change the display as shown below. [Image & Icons]
[Image & Information] [Image only]
[ Image & Icons ] [ Image & Information ] [ Image only ]
Pressing the LCD button
Pressing
the LCD
button
Pressing
the LCD
button
LCD ( ) button
Size :
3072X2304
Av : F2.8
Tv : 1/60
ISO : 75
Flash : Off
Date : 2005/01/01
69
Deleting Images in Play Mode
1. Select an image that you want to delete by pressing the
LEFT / RIGHT button and press the DELETE ( )
button.
2. A message will display as shown alongside on the LCD
monitor.
3. Press the OK button to delete the image.
Delete ( ) button
This deletes images stored on the memory card.
Before deleting images from the camera, you should protect (p.67) or download images
(p.106) to your computer that you wish to keep.
INFORMATION
Deleting Images in Thumbnail Display Mode
1. Use the Up/Down/Left/Right buttons to select an image to delete.
2. Press the Delete button to display the following message in the LCD monitor.
Press the DELETE
button.
112233
445566
778899
112233
445566
778899
3. Press the OK button to delete the image.
Delete?
Delete
Cancel
Confirm:OK
Delete?
Delete
Cancel
Confirm:OK
70
Album button (MF button)
You can organise the captured still images into albums
by using the MF button.
This camera has 8 albums and each album can take up
to 100 images.
How to use the album
Selecting the album
1. In the play mode, press the MF button.
2. Select [Select] menu by pressing the Up/Down button
and press the Right button.
3. Select a desired album by pressing the
Up/Down/Left/Right buttons and press the OK button.
Inserting still images into the album
1. After selecting an album, press the menu button.
2. Select the [Add] menu by pressing the Up/Down
button and press the Right button.
All A1 A2
A3 A4 A5
A6 A7 A8
Select
Slide
Add
Remove
Exit:MENU Move :
All A1 A2
A3 A4 A5
A6 A7 A8
Select
Slide
Add
Remove
Set : OK
A4
Select
Slide
Add
Remove
Select:T Set:OK
71
Album button (MF button)
Removing still images from the album
1. Select a desired album and press the menu button.
2. Select [Remove] menu by pressing the Up/Down button
and press the Right button.
3. Select a desired sub menu and press the OK button.
- [All Pics] : All of the still images in the album will be
removed.
- [Select] : Specific still images in the album can be
removed.
If [Select] is selected :
- Select images that you want to remove by pressing the
Up/Down/Left/Right buttons and press the Zoom T
button. V marks are displayed on the selected images.
4. Press the OK button and a confirmation window will
display.
Select a desired sub menu by pressing the UP/ DOWN
button and press the OK button.
[Remove] : Removes the selected images from the
album.
[Cancel] : Cancels the removing images.
* The removed images are not deleted from the memory,
but just removed from the album.
A4
Select:T Set:OK
A4
A4
Select:T Set:OK
A4
A4
Select
Slide
Add
Remove
Set : OK
Remove
Remove
Cancel
Confirm:OK
Select
All Pics
Select:T Set:OK
Select:T Set:OK
Select
Slide
Add
Remove
Select
Slide
Add
Remove
Add
Add
Cancel
Confirm:OK
3. Select the still images you wish to add by pressing the
Up/Down/Left/Right buttons and press the Zoom T
button. V marks are displayed on the selected images.
* To cancel the selection, press the Zoom T button again.
4. Press the OK button and a confirmation window will
display. Select a desired sub menu by pressing the UP/
DOWN button and press the OK button.
[Add] : Inserts the selected images into the album.
[Cancel] : Cancels the inserting images.
72
Album button (MF button)
If an image is deleted from the memory, the image doesn’t display on an album.
An image can’t be added twice into the same album.
An image can be added into the different albums.
INFORMATION
Playing back the albums
Playing back all of the albums
1. Select [All] menu and press the OK button.
All of the albums will be selected.
2. Press the menu button.
3. Select [Slide] menu by pressing the Up/Down button
and press the Right button.
You can select [Start], [Interval] and [Repeat] menus.
- [Start] : Start the slide show
- [Interval] : Set the slide show play interval
- [Repeat] : Choose to repeat the slide show after
finishing the first cycle.
- [Effect] : Unique screen effects can be used for the
slide show.
4. Select the [Start] menu by pressing the Up/Down button
and press the OK button to start the slide show.
Playing a desired album
1. Select a desired album and press the OK button.
2. Press the menu button.
3. Select [Slide] menu by pressing the Up/Down button
and press the Right button.
You can select [Start], [Interval], [Repeat] and [Effect]
menu.
4. Select [Start] menu and press the OK button to start the
slide show.
A4
Select
Slide
Add
Remove
Exit:MENU Move:
All A1 A2
A3 A4 A5
A6 A7 A8
Select
Slide
Add
Remove
Exit:MENU Move :
Start
Interval
Repeat
Effect
1 Sec
Off
Cancel
A4
Select
Slide
Add
Remove
Start
Interval
Repeat
Effect
1 Sec
Off
Cancel
Move: Set:OK
A4
Select
Slide
Add
Remove
Move : Set:OK
73
Setting up the play back function using the LCD monitor
PLAY mode functions can be changed by using the LCD monitor. In the PLAY mode,
pressing the MENU button displays the menu on the LCD monitor. The menus you can set
up in Play mode are as follows. To capture an image after setting up the play menu, press
the PLAY button.
Menu tab Main menu Sub menu Secondary menu Page
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Slide
p. 56
p. 56
p. 55
-
1, 3, 5, 10sec
Off, On
Cancel
Effect 1, 2, 3, 4
Right 90
Left 90
180
Horizontal
Vertical
Start
Interval
Repeat
DPOF
Standard
Index
Size
Select/ All Pics/ Cancel
No/ Yes
Select/ All Pics/ Cancel
Protect
Delete
Effect
Select
All Pics
Select
All Pics
Unlock / Lock
Resize
Rotate
p. 57
2816x2112
2592x1944
2272x1704
2048x1536
1600x1200
1024x768
640x480
User Image
74
Setting up the play back function using the LCD monitor
This menu is available while the camera is connected to a PictBridge supporting printer
(direct connection to the camera, sold separately) with a USB cable.
Menu tab Main menu Sub menu Secondary menu Page
-
-
-
-
Auto
Postcard
4X6
L
2L
A4
A3
Auto
Full
1
2
4
8
9
16
Auto
Plain
Photo
Fastphoto
Auto Set
Custom Set
Images
p. 75
p. 75
p. 74
No
Yes
Size
Layout
Type
One Pic
All Pics
75
Setting up the play back function using the LCD monitor
Menus are subject to change without prior notice.
Menu tab Main menu Sub menu Secondary menu Page
Auto
Draft
Normal
Fine
Auto
Off
On
Auto
Off
On
Standard -
Index -
No -
Yes -
No -
Yes -
Print
Custom Set
p. 76
p. 76
p. 77
p. 75
DPOF Print
Reset
Quality
Date
File Name
76
Starting the slide show
Images can be displayed continuously at pre-set intervals. You can view the slide show by
connecting the camera to an external monitor.
1. Press the play mode button and press the menu button.
2. Press the LEFT/ RIGHT button and select the [Slide]
menu tab.
Start the slide show: The slide show can start only in the
[Start] menu.
1. Use the Up/Down buttons to select the [Start] menu.
2. Press the OK button to start the slide show.
- Press the Pause button to pause the slide show.
- Press the Pause button ( ) again to resume the slide show.
- To stop the slide show, press the play & pause button, and then press the LEFT or RIGHT
button.
Setting play interval: Set the slide show play interval.
1. Select the [Interval] sub menu by pressing the UP/DOWN button and press the RIGHT
button.
2. Use the Up/Down buttons to select the desired interval.
3. Press the OK button to save the configuration.
Repeat setting : setting the slide show to repeat after the first cycle.
1. Use the Up/Down buttons to select the [Repeat] menu and press the Right button.
2. Use the Up/Down buttons to select the desired sub menu.
[Off] Selected : The slide show is closed after one cycle.
3. Press the OK button to save the configuration.
The loading time depends on the image size and quality.
While the slide show is playing, only the first frame of a MOVIE file is displayed.
INFORMATION
Exit: MENU Move :
Start
Interval 1 sec
Repeat OFF
Slide
77
Starting the slide show
Protecting images
Configure slide show effects: Unique screen effects can be used for the slide show.
1. Select the [Effect] sub menu by pressing the UP/ DOWN button and press the RIGHT
button.
2. Use the Up/Down Button to select the type of effect.
[Cancel] : Normal display.
[Effect 1] : Image is displayed slowly.
[Effect 2] : Image is displayed slowly from the centre
outwards.
[Effect 3] : Image moves from the top left.
[Effect 4] : The image slides diagonally from top left to
bottom right.
3. Press the OK button to confirm the setting.
This is used to protect specific shots from being accidentally erased (Lock).
It also unprotects images that have been previously protected (Unlock).
Protecting Images
1. Press the play mode button and press the menu button.
2. Press the LEFT/ RIGHT button and select the [Protect]
menu tab.
3. Select a desired sub menu by pressing the UP/ DOWN
button and press the OK button.
[Select] : Selection window for an image to be
protected/released is displayed.
- Up/Down/Left/Right : Select an image
- Zoom W/T Button : Protect/release the image
- Menu Button : Your changes will be saved and the
menu will disappear.
[All Pics] : Protect/release all saved images
- Zoom W/T Button : Protect/release the images
- Menu Button : Your changes will be saved and the
menu will disappear.
SET:OK
WUnlock T
SET:OK
WLock T
Back: Set : OK
Slide
Interval Cancel
Repeat Effect1
Effect Effect2
Exit: MENU Move :
Select
All Pics
Protect
78
Protecting images
- If you protect an image, the protect icon will be displayed
on the LCD monitor. (An unprotected image has no
indicator)
- An image in LOCK mode will be protected from the
delete function or [Delete] functions, but will NOT be
protected from the [Format] function.
Deleting images
Of all the files stored in the memory card, the unprotected files in the DCIM subfolder will be
deleted. Remember that this will permanently delete unprotected images.
Important shots should be stored on a computer before deletion takes place. The startup
image is stored in the camera's internal memory (i.e., not on the memory card) and it will not
be deleted even if you delete all files on the memory card.
Deleting images
1. Press the play mode button and press the menu button.
2. Press the LEFT/ RIGHT button and select the [Delete]
menu tab.
3. Select a desired sub menu by pressing the UP/ DOWN
button and press the OK button.
[Select]: Selection window for an image to delete is
displayed.
- Up/Down/Left/Right: Select an image
- Zoom T Button: Select the image for deletion.
( mark)
- OK Button: Press the OK Button to display the
confirmation message. Press the OK Button
again to delete V marked images.
[All Pics] : Displays confirmation window. Select the
[Delete] menu and press the OK button to
delete all unprotected images.
4. After deletion, the screen will be changed to the play
mode screen.
Del:OK
Select:T
Del:OK
Delete?
Delete
Cancel
Confirm:OK
Exit: MENU Move :
Select
All Pics
Delete
79
Resize
Change the resolution (size) of pictures taken. Select [User Image] to save an image to be
the start-up image. The resized image will have a new file name.
1. Press the play mode button and press the menu button.
2. Press the LEFT/ RIGHT button and select the [Resize]
menu tab.
3. Select a desired sub menu by pressing the UP/ DOWN
button and press the OK button.
A large sized image can be resized to a smaller sized image, but not vice versa.
Only JPEG images can be resized.
TIFF, Movie clip(AVI) and Voice recording(WAV) files can’t be resized.
You can change the resolution of only those files compressed in the JPEG 4:2:2 format.
The resized image will have a new file name. The [User Image] image is stored not on the
memory card but on the internal memory.
Only two [User Image] images can be saved. If you save a new [User Image] image, the
existing startup image will be deleted in order.
If the memory capacity is insufficient to store the resized image, a [Card Full!] message
will display on the LCD monitor and the resized image will not be stored.
INFORMATION
Image Resize Types
3072 O O O O O O O O
2816 X O O O O O O O
2592 X X O O O O O O
2272 X X X O O O O O
2048 X X X X O O O O
1600 X X X X X O O O
1024 X X X X X X O O
640 X X X X X X X O
Resize
2272X
1704
2816X
2112
2592X
1944
2048X
1536
1600X
1200
1024X
768
640X
480
User
Image
Exit: MENU Move :
2816X2112
2592X1944
2272X1704
Resize
80
Rotating an image
You can rotate the stored images by 90, 180, or 270 degrees.
1. Press the play mode button and press the menu button.
2. Press the LEFT/ RIGHT button and select the [Rotate]
menu tab.
3. Select a desired sub menu by pressing the UP/ DOWN
button.
4. Press the OK button and a confirmation window will
display. Select a desired sub menu by pressing the UP/
DOWN button and press the OK button.
[Rotate] : The image will be rotated.
[Cancel] : The rotation will be cancelled.
5. Press the OK button and the rotated image will be displayed.
If you display the rotated image on the LCD monitor, empty spaces may appear to the left and
right of the image.
[Right 90 ] : Rotate picture in
a clock-wise
direction
[Left 9 ] : Rotate picture in a
counter clock- wise
direction
[180 ] : Rotate picture 180
degrees
[Horizontal] : Rotate picture
horizontally
[Vertical] : Rotate picture
vertically
Exit: MENU Move :
Right 90˚
Left 90˚
180˚
Rotate
81
DPOF : STANDARD
This function allows you to embed print quantity information on a stored image.
1. Press the play mode button and press the menu button.
2. Press the LEFT/ RIGHT button and select the [DPOF]
menu tab.
3. Select the [Standard] menu by pressing the UP/ DOWN
button and press the RIGHT button.
4. Select a desired sub menu by pressing the UP/ DOWN
button and press the OK button.
[Select]: Selection window for an image to print is
displayed.
- Up/Down/Left/Right: Select an image to print.
- Zoom W/T Button: Select the number of prints.
[All Pics] : Configure number of prints for all pictures
except movie and voice files.
- Zoom W/T Button: Select the number of prints.
[Cancel] : Cancel the print setup.
5. Press the OK button to confirm the setting. If an image
carries DPOF instructions, the DPOF indicator ( )
will show.
DPOF
DPOF(Digital Print Order Format) allows you to embed printing information on your memory
card’s MISC folder. Select the pictures to be printed and how many prints to make.
The DPOF indicator will display on the LCD monitor when an image that has DPOF
information plays back. Images can then be printed on DPOF printers, or at an increasing
number of photo labs.
This function is not available for Movie clips and Voice recording files.
Set:OK
W 0 Prints T
Set:OK
W0 Prints T
Exit: MENU Move :
Standard Select
Index No
Size Select
DPOF
82
DPOF : INDEX
Images (except for movie clips and voice file) are printed as index type.
1. Press the play mode button and press the menu button.
2. Press the LEFT/ RIGHT button and select the [DPOF]
menu tab.
3. Select the [Index] menu by pressing the UP/ DOWN
button and press the RIGHT button.
4. Select a desired sub menu by pressing the UP/ DOWN
button.
If [No] is selected : Cancel the index print setting.
If [Yes] is selected : The image will be printed in index format.
5. Press the OK button to confirm the setting.
DPOF : PRINT SIZE
You can specify the print size when printing images stored on the memory card.
The [Size] menu is available only for DPOF 1.1 compatible printers.
Setting the Print Size
1. Press the play mode button and press the menu button.
2. Press the LEFT/ RIGHT button and select the [DPOF]
menu tab.
3. Select the [Size] menu by pressing the UP/ DOWN button
and press the RIGHT button.
4. Select a desired sub menu by pressing the UP/ DOWN
button and press the OK button.
[Select] : Selection window for an image to be changed
printed size is displayed.
- Up/Down/Left/Right : Select an image.
- Zoom W/T Button : Change the print size.
- OK button : Your changes will be saved and the menu
will disappear.
[All Pics] : Change print size of all saved images
- Zoom W/T button : Change the print size
- OK button : Confirm the changed setting.
[Cancel] : Cancel all of the print size settings.
* DPOF [Size] secondary menu : Cancel, 3X5, 4X6, 5X7,
8X10
Back: Set : OK
DPOF
Standard
Index No
Size Yes
Back: Set : OK
DPOF
Standard Select
Index All Pics
Size Cancel
Set:OK
W Cancel T
Set:OK
W Cancel T
83
PictBridge
You can use the USB cable to connect this camera to a printer that supports PictBridge (sold
separately) and print the stored images directly. TIFF, Movie clips and voice files cannot be
printed. You can set up the following settings from the PictBridge menu.
Images : Select the pictures to be printed.
PRINTER SETUP : Setting up printing(Auto Set/Custom Set)
Print : Printing pictures
DPOF Print : Printing the DPOF files
Reset : Initialising the PictBridge functions
Connecting the Camera to a Printer
1. Press the POWER button to turn on the camera.
2. In a mode other than Voice Recording mode, press the
MENU button.
3. Press the LEFT/ RIGHT button and select [Setup] menu
tab.
4. Select [USB] menu by pressing the UP/ DOWN button
and press the RIGHT button.
5. Select [Printer] menu by pressing the UP/ DOWN button
and press the OK button.
6. Press the menu button twice and the menu will disappear.
7. Use the supplied USB cable to connect the camera to the printer as shown below.
8. Turn on the printer to connect the camera to the printer.
If you selected [Computer] in Step 5, when you connect the camera to your printer, the Mode
dial lamp(Green) will illuminate and the connection will not be established. In this case,
disconnect the USB cable, and then follow the procedure from Step 2 and onward.
Back: Set : OK
Setup
Imprint
Sound Computer
USB Printer
84
PictBridge: Picture Selection
Select pictures to print
1. Connect the camera to your printer. The USB menu must
be set to [Printer] before you connect the camera to the
printer.(See p.86)
2. The [Images] menu will appear.
3. Use the UP and DOWN buttons to select the desired
submenu value, and then press the OK button.
When [One Pic] is selected : The PictBridge function will
be applied only to the picture currently displayed.
When [All Pics] is selected : The PictBridge function will be applied to all pictures, excluding
TIFF, movie clips and voice files.
[ When [One Pic] is selected ] [ When [All Pics] is selected ]
- Press the Up/Down button to select the number of prints. Maximum 30 prints.
- Use the Left/Right button to select another picture and select the number of prints for
another picture.
- After setting the number of prints, press the OK button to save.
- Press the Shutter button to return to the menu without setting the number of prints.
0
Exit:Shutter Set:OK
Setting the Number of Copies to Print
- Select [One Pic] or [All Pics]. A screen where you can set the number of copies to print will
appear as shown below.
PREV NEXT
0
Exit:Shutter Set:OK
Exit: MENU Move :
One Pic
All Pics
Images
85
PictBridge: Print Setting
Menu
Size Setting the size of the printing paper
Auto, Postcard, 4x6, L, 2L, A4, A3
Layout
Setting the number of pictures to be printed on a sheet of paper
Auto, Full, 1, 2, 4, 8, 9, 16
Type Setting the quality of the printing paper Auto, Plain, Photo, Fastphoto
Quality
Setting the quality of the picture to be printed
Auto, Draft, Normal, Fine
Date Setting whether to print the date Auto, Off, On
File Name Setting whether to print the file name Auto, Off, On
AUTO SET
1. Connect the camera to your printer. The USB menu
must be set to [Printer] before you connect the camera
to the printer. (See p.86)
2. Use the LEFT and RIGHT buttons to select the [Auto
Set] menu tab.
3. Use the UP and DOWN buttons to select the desired
submenu value, and then press the OK button.
[No] : [Custom Set] values are kept.
[Yes] : All values in the [Custom Set] are automatically changed.
Some menu options are not supported in all manufacturer and printer models. If not
supported, the menus are still displayed in the LCD, but are not selectable.
If the setting values are not changed in the automatic/manual setting, the setting values are
automatically kept.
1. Connect the camera to your printer. The [USB] menu
must be set to [Printer] before you connect the camera to
the printer.(See p.86)
2. Use the LEFT and RIGHT buttons to select the [Custom
Set] menu tab.
3. Use the UP and DOWN buttons to select the desired
submenu value, and then press the RIGHT button.
4. Use the UP and DOWN buttons to select the desired
submenu value, and then press the OK button.
CUSTOM SET : You can select the Paper Size, Print Format, Paper Type, Print Quality, Date
Print, and File Name Print menus for printed pictures.
Function Sub menu
The menus you can set up are as follows:
Exit: MENU Move :
No
Yes
Auto Set
Custom Set
Back:
Set : OK
Size Auto
LayOut PostCard
Type 4X6
86
PictBridge: Printing
Printing Pictures
1. Connect the camera to your printer. The USB menu
must be set to [Printer] before you connect the camera
to the printer. (See p.86)
2. Use the LEFT and RIGHT buttons to select the [Print]
menu tab.
3. Use the UP and DOWN buttons to select the desired
submenu value, and then press the OK button.
[Standard] : Print the pictures stored in the
memory card in set numbers. One picture is printed on one piece of
paper.
[Index] : Print multiple images on one sheet of paper.
1. Connect the camera to your printer. The [USB] menu
must be set to [Printer] before you connect the camera
to the printer. (See p.86)
2. Use the LEFT and RIGHT buttons to select the [DPOF
Print] menu tab.
3. Use the UP and DOWN buttons to select the desired
submenu value, and then press the OK button.
[Yes] : Directly print the file with the DPOF information
[No] : Cancel the printing
Depending on the manufacturer and printer model, some menus may not be available.
With a printer without supporting the DPOF, the menu is still displayed but not available.
4. The screen shown on the right will appear and the
picture will be printed. If no picture is selected, the [No
Image !] message will be displayed. Press the Menu/OK
button while printing to cancel the printing and the
[Images] menu is displayed.
Number of pictures in a index print varies depends on
the printer used.
DPOF PRINT : This allows you to directly print the files with DPOF information.
Print
Exit : MENU Move:
Standard
Index
Now Printing
1/1
Cancel : OK
DPOF Print
Exit : MENU Move:
No
Yes
87
PictBridge : RESET
Initialises user-changed configurations.
1. Connect the camera to your printer. The [USB] menu
must be set to [Printer] before you connect the camera
to the printer. (See p.86)
2. Use the LEFT and RIGHT buttons to select the [Reset]
menu tab.
3. Use the UP and DOWN buttons to select the desired
submenu value, and then press the OK button.
- If [Yes] is selected : All print and image settings will be reset.
- If [No] is selected : Settings will not be reset.
Default print setting varies depending on the printer manufacturer.
For your printer’s default setting, refer to the user’s guide that came with your printer.
Reset
Exit : MENU Move:
No
Yes
88
Setup menu
In this mode, you can set up basic settings.
You can use the setup menu in all camera modes, except Voice Recording mode.
The items indicated by are default settings.
Menu tab Main menu Sub menu Secondary menu Page
Reset -
Series -
PWR OFF Off, 1, 3, 5, 10 min - p.80
ENGLISH
P”CCK»…
PORTU.
FRANÇAIS DUTCH
DEUTSCH DANSK
ESPAÑOL SVENSKA
ITALIANO SUOMI
BAHASA
No -
Yes -
05/01/01 13:00 -
yy/mm/dd -
dd/mm/yy -
mm/dd/yy -
Off -
IMPRINT Date - p.82
D & Time -
Off -
Low -
Medium -
High -
FILE
FORMAT
D & TIME
SOUND
p.79
p.81
p.82
p.83
89
Setup menu
This function allows the user to select the file naming format.
Assigning File Names
1. In any mode with the exception of Voice Recording mode,
press the MENU button.
2. Press the LEFT/ RIGHT button and select the [Setup]
menu tab.
3. Select the [File] menu by pressing the UP/ DOWN button
and press the RIGHT button.
4. Select a desired sub menu by pressing the UP/ DOWN
button and press the OK button.
[Reset] : After using the reset function, the next file name will be set from 0001 even
after formatting, deleting all or inserting a new memory card.
[Series] : New files are named using numbers that follow the previous sequence, even
when a new memory card is used, or after formatting, or after deleting all
pictures
5. Press the menu button twice and the menu will disappear.
File name
* Menus are subject to change without prior notice.
Back:Set : OK
File
Reset
Power Off Series
Language
3072
Setup
Menu tab Main menu Sub menu Secondary menu Page
Computer -
Printer -
Off -
On -
Dark -
LCD Normal - p.85
Bright -
NTSC -
PAL -
Quick View Off/ 1, 3, 5 sec -
No -
Yes -
USB
Video Out
AF Lamp
Reset
p.83
p.84
p.85
p.86
90
File name
The first stored folder name is 100SSCAM, and the first file name is SV100001.
File names are assigned sequentially from SV100001 SV100002 ~ SV109999.
The folder number is assigned sequentially from 100 to 999 as follows
: 100SSCAM 101SSCAM ~ 999SSCAM.
The files used with the memory card conform to the DCF(Design rule for Camera File
systems) format.
INFORMATION
Even if the batteries or AC adapter are removed and inserted again, the power off setting
will be preserved.
Note that the automatic power off function will not operate if the camera is in PC mode, slide
show, playing back a voice recording, playing back a movie clip or during composite shooting.
INFORMATION
Auto power off
Setting Power Off
1. In any mode with the exception of Voice Recording mode,
press the MENU button.
2. Press the LEFT/ RIGHT button and select the [Setup]
menu tab.
3. Select the [Power Off] menu by pressing the UP/ DOWN
button and press the RIGHT button.
4. Select a desired sub menu by pressing the UP/ DOWN
button and press the OK button.
Selecting [Off] : The power off function will not operate.
[1~10 min] : The power will turn off automatically if not used for the period of time
specified.
5. Press the menu button twice and the menu will disappear.
This function switches the camera off after a set amount of time in order to prevent
unnecessary battery drainage.
Back:Set : OK
File
Off
Power Off 1 min
Language 3 min
3072
Setup
91
Language
Setting Language
1. In any mode with the exception of Voice Recording mode,
press the MENU button.
2. Press the LEFT/ RIGHT button and select the [Setup]
menu tab.
3. Select the [Language] menu by pressing the UP/ DOWN
button and press the RIGHT button.
4. Select a desired sub menu by pressing the UP/ DOWN
button and press the OK button.
LANGUAGE sub menu : English, Korean, French, German, Spanish, Italian, S. Chinese,
T. Chinese, Japanese, Russian, Portuguese, Dutch, Danish, Swedish, Finnish, Thai,
BAHASA(MALAY/ INDONISIA) and Arabic.
5. Press the menu button twice and the menu will disappear.
Formatting a Memory Card
1. In any mode other than Voice Recording mode, press the
MENU button.
2. Press the LEFT/ RIGHT button and select the [Setup]
menu tab.
3. Select the [Format] menu by pressing the UP/ DOWN
button and press the RIGHT button.
4. Select a desired sub menu by pressing the UP/ DOWN
button and press the OK button.
If [No] is selected : The memory card will not be formatted.
Press the menu button twice and the menu display will disappear.
If [Yes] is selected : A [Please Wait !] message appears and the memory card will be
formatted. If you ran FORMAT in Play mode, a [No Image !]
message will appear.
There is a choice of languages that can be displayed on the LCD monitor. Even if the batteries or
AC adapter are removed and inserted again, the language setting will be preserved.
Formatting a memory card
This is used for formatting the memory card. If you run [Format] on the memory card, all
images, including the protected images, will be deleted. Be sure to download important
images to your PC before formatting the memory card.
Be sure to run [Format] on the following types of memory card.
- A new memory card, or an unformatted memory card.
- A memory card that has a file this camera can t recognise or one that has been taken
from another camera.
Note that the automatic power off function will not operate if the camera is in PC mode, slide
show, playing back a voice recording, playing back a movie clip and the [Composite] shots.
INFORMATION
Back:Set : OK
File
English
Power Off
Language
Français
3072
Setup
Back:Set : OK
Power Off
Language No
Format
Yes
3072
Setup
92
Setting up the Date/ Time/ Date type
You can change the date and time that will be displayed on the captured images and set up
the date type.
Setting Date/Time & Selecting Date Format
1. In any mode with the exception of Voice Recording mode,
press the MENU button.
2. Press the LEFT/ RIGHT button and select the [Setup]
menu tab.
3. Select the [D & Time] menu by pressing the UP/ DOWN
button and press the RIGHT button.
4. Use the UP, DOWN, LEFT, and RIGHT buttons to select
the desired submenu value, and then press the OK button.
RIGHT button : Selects the year/month / day/hour / minute date type.
LEFT button : Moves the cursor to the [D & Time] main menu if the cursor is at the first item
of the date and time setup. In all other cases, the cursor will be shifted to the
left of its current position.
UP and DOWN buttons : Changes the setting value.
- Date type : [yy/mm/dd] /[dd/mm/yy] /[mm/dd/yy]
5. Press the menu button twice and the menu will disappear.
There is an option to include DATE/TIME on still images.
Date Imprinting
1. In any mode with the exception of Voice Recording mode,
press the MENU button.
2. Press the LEFT/ RIGHT button and select the [Setup]
menu tab.
3. Select the [Imprint] menu by pressing the UP/ DOWN
button and press the RIGHT button.
4. Use the UP and DOWN buttons to select the desired date
imprint type, and then press the OK button.
[Off] : The DATE & TIME will not be imprinted on the image file.
[Date] : Only the DATE will be imprinted on the image file.
[D & Time] : The DATE & TIME will be imprinted on the image file.
5. Press the menu button twice and the menu will disappear.
* The Date & Time are imprinted at the bottom right side of the still image.
* The date will be imprinted as a DATE TYPE setting.
* TIME is imprinted in the following way : [Hour : Minute] and hours are shown using the 24
hour clock.
* The imprint function is applied only to still images except for the images taken in the [Text]
scene mode.
Imprinting the recording date
Back:Set : OK
Format Off
D & Time Date
lmprint D & Time
3072
Setup
Back:Set : OK
Language
Format
D & Time
3072
Setup
05 / 01/ 01 01:00
yy/mm/dd
93
Sound
Connecting an External Device (USB)
If you set the operation sound to ON, various sounds will be activated for camera startup,
when button are pressed, and if there is a card error, so that you can be aware of the camera
operation status.
Setting Operation Sounds
1. In any mode with the exception of Voice Recording mode,
press the MENU button.
2. Press the LEFT/ RIGHT button and select the [Setup]
menu tab.
3. Select the [Sound] menu by pressing the UP/ DOWN
button and press the RIGHT button.
4. Select a desired sub menu by pressing the UP/ DOWN
button and press the OK button.
[Sound] sub menu : Off/ Low/ Medium/ High
5. Press the menu button twice and the menu will disappear.
You can select an external device to which you want to connect the camera using the USB
cable.
Selecting an External Device
1. In any mode with the exception of Voice Recording mode,
press the MENU button.
2. Press the LEFT/ RIGHT button and select the [Setup]
menu tab.
3. Select the [USB] menu by pressing the UP/ DOWN button
and press the RIGHT button.
4. Select a desired sub menu by pressing the UP/ DOWN
button and press the OK button.
[Computer] : Select this if you want to connect the camera to your PC.
Refer to page 105 for instructions on how to connect the camera to your
PC.
[Printer] : Select this if you want to connect the camera to your printer.
Refer to page 73 for instructions on how to connect the camera to your
printer.
5. Press the menu button twice and the menu will disappear.
Back:Set : OK
D & Time Off
lmprint Low
Sound Medium
3072
Setup
Back:Set : OK
lmprint
Sound Computer
USB Printer
3072
Setup
94
Auto Focus lamp
LCD brightness
You can adjust the LCD brightness.
Adjusting LCD Brightness
1. In any mode with the exception of Voice Recording mode,
press the MENU button.
2. Press the LEFT/ RIGHT button and select the [Setup]
menu tab.
3. Select the [LCD] menu by pressing the UP/ DOWN button
and press the RIGHT button.
4. Select a desired sub menu by pressing the UP/ DOWN
button and press the OK button.
[LCD] sub menu : Dark, Normal, Bright
5. Press the menu button twice and the menu will disappear.
You can turn on and off the Auto Focus lamp
How to set up the lamp
1. In any mode with the exception of Voice Recording mode,
press the MENU button.
2. Press the LEFT/ RIGHT button and select the [Setup]
menu tab.
3. Select the [AF Lamp] menu by pressing the UP/ DOWN
button and press the RIGHT button.
4. Select a desired sub menu by pressing the UP/ DOWN
button and press the OK button.
If [Off] is selected : The AF lamp will not light up.
If [On] is selected : The AF lamp will light up.
If you select [Off] menu and take an image in poorly lit condition or select the [Night]
scene mode, the camera may not take exact focus.
Back:Set : OK
Sound
USB Off
AF Lamp On
3072
Setup
Back:Set : OK
USB Dark
AF Lamp Normal
LCD Bright
3072
Setup
95
Selecting Video out type
The Movie output signal from the camera can be NTSC or PAL.
Your choice of output will be governed by the type of device (monitor or TV, etc.) to which the
camera is connected. PAL mode can support only BDGHI.
Setting the Video Out Type
1. In any mode with the exception of Voice Recording mode,
press the MENU button.
2. Press the LEFT/ RIGHT button and select the [Setup]
menu tab.
3. Select the [Video Out] menu by pressing the UP/ DOWN
button and press the RIGHT button.
4. Select a desired sub menu by pressing the UP/ DOWN
button and press the OK button.
[Video Out] sub menu : NTSC, PAL
5. Press the menu button twice and the menu will disappear.
NTSC : U.S.A, Canada, Japan, South Korea, Taiwan, Mexico.
PAL : Australia, Austria, Belgium, China, Denmark, Finland, Germany, U.K., Holland,
Italy, Kuwait, Malaysia, New Zealand, Singapore, Spain, Sweden, Switzerland,
Thailand, Norway.
When using a TV as an external monitor, you will need to select the external or AV
channel of the TV.
There will be a digital noise on the external monitor, but it is not a malfunction.
If the image is not in the centre of the screen, use the TV controls to centre it.
When the camera is connected to an external monitor, the menu will be visible on the
external monitor and the menu functions are the same as those indicated on the LCD
monitor.
INFORMATION
Connecting to an external monitor
In RECORDING/ PLAY mode, you can
view the stored still images or movie clips
by connecting the camera to an external
monitor via the A/V cable. When the
camera is connected to an external
monitor, the LCD monitor will be turned
off automatically.
Yellow Colour-Video
White Colour-Voice
Back:Set : OK
AF Lamp
LCD NTSC
Video Out PAL
3072
Setup
96
Quick view
If you enable Quick View before capturing an image, you can view the image you just
captured on the LCD monitor for the duration set in the [Quick View] setup. Quick view is
possible only with still images.
Setting Quick View
1. In any mode with the exception of Voice Recording mode,
press the MENU button.
2. Press the LEFT/ RIGHT button and select the [Setup]
menu tab.
3. Select the [Quick View] menu by pressing the UP/ DOWN
button and press the RIGHT button.
4. Select a desired sub menu by pressing the UP/ DOWN
button and press the OK button.
[off] : The quick view function can’t be activated.
[1 ~ 3 sec] : The captured image is briefly displayed during the selected time.
5. Press the menu button twice and the menu will disappear.
Initialisation(RESET ALL)
All camera menu and function settings will be restored to their default values.
However, values for DATE/ TIME, LANGUAGE, and VIDEO OUT will not be changed.
Initialising the Camera
1. In any mode with the exception of Voice Recording mode,
press the MENU button.
2. Press the LEFT/ RIGHT button and select the [Setup]
menu tab.
3. Select the [Reset] menu by pressing the UP/ DOWN
button and press the RIGHT button.
4. Select a desired sub menu by pressing the UP/ DOWN
button and press the OK button.
If [No] is selected : Settings will not be restored to their defaults.
If [Yes] is selected : All settings will be restored to their defaults.
5. Press the menu button twice and the menu will disappear.
Back:Set : OK
LCD Off
Video Out 1 sec
Quick View 3 sec
3072
Setup
Back:Set : OK
Video Out
Quick View No
Reset Yes
3072
Setup
97
Setting up the MYCAM menu
You can set up a start up image, start up sound and shutter sound. Every camera working
mode (with the exception of Voice recording mode) has the MyCAM menu.
The items indicated by are default settings.
Menu tab Main menu Sub menu Page
Off LOGO
User Image 1 User Image 2
Off Sound 1
Sound 2 Sound 3
Off Sound 1
Sound 2 Sound 3
S.Image
S.Sound
SH.Sound
p.87
p.88
p.88
You can select the image that is first displayed on the LCD monitor whenever the camera is
turned on.
Setting a Startup Image
1. In any mode with the exception of Voice Recording mode,
press the MENU button.
2. Press the LEFT/ RIGHT button and select the [MyCam]
menu tab.
3. Select the [S.Image] menu by pressing the UP/ DOWN
button and press the RIGHT button.
4. Select a desired sub menu by pressing the UP/ DOWN
button and press the OK button.
5. Press the menu button twice and the menu will disappear.
Start up image
Use a saved image for the start-up image with the [LOGO] in the [Resize] menu in the
play mode.
The start-up image will not be deleted by deleting all images or [Format] menu.
The User images will be deleted by [Reset] menu.
INFORMATION
* Menus are subject to change without prior notice.
Back:Set : OK
S.Image
S.Sound
SH.Sound
3072
Mycam
98
Start up sound
You can select the shutter sound.
Selecting the Shutter Sound
1. In any mode with the exception of Voice Recording mode,
press the MENU button.
2. Press the LEFT/ RIGHT button and select the [MyCam]
menu tab.
3. Select the [SH.Sound] menu by pressing the UP/ DOWN
button and press the RIGHT button.
4. Select a desired sub menu by pressing the UP/ DOWN
button and press the OK button.
5. Press the menu button twice and the menu will disappear.
Shutter sound
Setting the Startup Sound
1. In any mode with the exception of Voice Recording mode,
press the MENU button.
2. Press the LEFT/ RIGHT button and select the [MyCam]
menu tab.
3. Select the [S.Sound] menu by pressing the UP/ DOWN
button and press the RIGHT button.
4. Select a desired sub menu by pressing the UP/ DOWN
button and press the OK button.
5. Press the menu button twice and the menu will disappear.
Back:Set : OK
3072
Mycam
S.Image Off
S.Sound Sound1
SH.Sound Sound2
Back:Set : OK
3072
Mycam
S.Image Off
S.Sound Sound1
SH.Sound Sound2
You can select the sound that is activated whenever the camera is turned on.
99
Important notes
Be sure to observe the following precautions!
This unit contains precision electronic components. Do not use or store this unit in the
following locations.
- Areas exposed to severe changes in temperature and humidity.
- Areas exposed to dust and dirt.
- Areas exposed to direct sunlight or the inside of a vehicle in hot weather.
- Environments where there is high magnetism or excessive vibration.
- Areas with high explosives or highly flammable materials.
Do not let the unit come into contact with dust, vinyl goods, or chemicals, such as
insecticides, for an extended period of time.
Sand can be particularly troublesome to cameras.
- Do not let sand get inside the unit when using it on beaches, coastal dunes, or other areas
where there is lots of sand.
- Doing so may result in failure or may permanently render the unit unusable.
Handling the camera
- Never drop the camera or subject it to severe shocks or vibrations.
- This camera is not waterproof. To avoid dangerous electrical shocks, never hold or operate
the camera with wet hands.
- If you use this camera in wet places, such as beach or pool, do not let water or sand get
inside the camera.
Extremes in temperature may cause problems.
- If the camera is transferred from a cold to a warm and humid environment, condensation
can form on the delicate electronic circuitry. If this occurs, turn the camera off and wait for at
least 1 hour until all moisture is dispersed. Moisture build up can also occur in the memory
card. If this happens, turn off the camera and remove the memory card. Wait until the
moisture has dispersed.
100
Important notes
Caution on Using the Lens
- If the lens is subjected to direct sunlight, it could result in discoloration and deterioration of
the image sensor.
- Pay attention not to get fingerprints or foreign substances on the surface of the lens.
If the digital camera is not used for a long period, an electric discharge can occur.
It is a good idea to remove the batteries and the memory card if you do not intend using the
camera for an extended period of time.
If the camera is exposed to an electronic interference, it will turn itself off to protect the
memory card.
Camera Maintenance
- Use a soft brush (available from photo stores) to gently clean the lens and LCD assemblies.
If this does not work, lens-cleaning paper with lens cleaning fluid can be used.
Clean the camera body with a soft cloth. Do not allow this camera to come into contact with
solvent materials such as benzol, insecticide, thinners etc. This may damage the body shell
of the camera and also affect its performance. Rough handling can damage the LCD
monitor. Take care to avoid damage and keep the camera in its protective carry case at all
times when not in use.
Do not attempt to disassemble or modify the camera.
Under certain conditions, static electricity can cause the flash unit to fire. This is not harmful to
the camera and is not a malfunction.
When images are uploaded or downloaded, the data transfer may be affected by static
electricity. In this case, disconnect and re-connect the USB cable before trying the transfer
again.
Before a important event or going on a trip, you should check the camera condition.
- Take a picture for testing the camera condition and prepare extra batteries.
- Samsung cannot be held responsible for camera malfunctions.
101
Warning indicator
There are several warnings that may appear on the LCD display.
Card Error !
Memory card error
Turn off the camera power and turn it on again
Insert the memory card again
Insert the memory card and format the memory card (p.73)
No Card !
A memory card is not inserted
Insert a memory card
The camera can t recognise the memory card
Insert the memory card again
Turn off the camera power and turn it on again
Card Locked !
The memory card is locked
SD memory card : Slide the write protect switch to the top of the memory card
Card Full !
There is insufficient memory capacity to take an image
Insert a new memory card
Delete unnecessary image files to free up some memory
No Image !
There are no images stored on the memory card
Take images
Insert a memory card that is holding some images
File Error !
File error
Format the memory card
Memory card error
Contact a camera service centre
Low Battery !
There is low battery capacity
Insert fresh batterie
102
Warning indicator
Please check the following
Before contacting a service centre
Low Light !
When taking pictures in dark places
Use a tripod and take pictures in Flash Photography mode
Set USB
[USB] sub menu and connected device are not matched.
Reconfigure [USB] in the [SETUP] menu.
Out Of Number
When selecting too many printing pages in the PictBridge menu.
Select printing page within the limitation.
The camera doesn’t switch on
There is low battery capacity.
Insert fresh batteries.
Batteries are inserted incorrectly with the reverse polarities.
Insert the batteries according to the polarity marks (+, -).
The camera power ceases while in use.
The batteries are exhausted.
Insert fresh batteries.
The Camera is turned off automatically.
Turn off the camera power and turn it on again.
Batteries drain quickly
The Camera is being used in low temperatures.
Keep the camera in warm conditions (i.e. inside a coat or jacket) and only remove it in
order to take images.
103
Before contacting a service centre
Camera does not take images when pressing the Shutter button
There is insufficient memory capacity.
Delete unnecessary image files
The memory card has not been formatted
Format the memory card (p.73)
The memory card is exhausted
Insert a new memory card
The memory card is locked
Refer to [Card Locked !] error message (p.93)
The camera’s power is off
Turn the camera power on
The batteries are exhausted
Insert fresh batteries
Batteries are inserted incorrectly with the reverse polarities.
Insert the batteries according to the polarity marks (+, -).
The camera suddenly stops working while in use
The camera was stopped due to a malfunction
Remove /re-insert batteries and switch the camera on
The images are unclear
A picture was taken within 0.8 m from the subject without setting an appropriate macro mode
If the subject is closer than 0.8m, select macro shot mode
Taking a picture beyond the flash range
Take a picture within the flash range
The lens is smudged or dirty
Clean the lens
The flash does not fire
Flash off mode has been selected
Dis-engage flash off mode
The camera mode can’t use the flash
Refer to the FLASH instruction (p.27)
Incorrect date and time is displayed
The date and time have been set incorrectly or the camera has adopted the default settings
Reset the date and time correctly
104
Before contacting a service centre
The images don't play back
Incorrect file name (Violation of DCF format)
Do not change the image file name
Colour of image is different to the original scene
White balance setting is incorrect
Select appropriate White balance
Images are too bright
Exposure is excessive
Reset exposure compensation
No image on external monitor
The external monitor has not been connected properly with the camera
Check the connection cables
There are incorrect files in the memory card
Insert a memory card that has correct files
When using the PC’s explorer, the [Removable Disk] file does not show
Cable connection is incorrect
Check the connection
The camera is off
Turn the camera on
The operating system is not Windows 98, 98SE, 2000, ME, XP/ Mac OS 9.0 ~ 10.3.
Alternatively the PC does not support USB
Install Windows 98, 98SE, 2000, ME, XP/ Mac OS 9.0 ~ 10.3 to PC that supports USB
The camera driver is not installed
Install a [USB Storage Driver]
105
Specifications
Type 1/1.8" CCD
Effective Pixel Approx. 7.1 Mega-pixel
Total Pixel Approx. 7.4 Mega-pixel
SHD Lens f = 7.8 ~ 23.4 mm
(35mm film equivalent : 38 ~ 114 mm)
F No. F2.8 ~ F7.7
Still Image mode : 1.0X ~ 10.0X
Play mode : 1.0X ~ 12.0X (depends on image size)
Optical Viewfinder
Real image optical viewfinder
LCD Monitor 2.0" Colour TFT LCD (117,600 dot)
Type TTL auto focus, Manual focus
Normal : 80cm ~ infinity
Macro : 4 ~ 80cm (Wide), 25 ~ 80cm (Tele)
Auto Macro : 4cm ~ infinity (Wide), 25 ~ infinity (Tele)
Type Mechanical and Electronic shutter
Shutter Auto : 1 ~ 1/2,000 sec. Manual : 15 ~ 1/2,000 sec.
Night : 8 ~ 1/2,000 sec.
Program AE, Shutter Priority AE, Aperture Priority AE or
Control Manual Exposure
Metering : Multi, Spot
Compensation 2.0EV (0.3EV steps)
ISO Equivalent Auto, 50, 100, 200, 400
Auto, Auto & Red-eye reduction,
Slow sync, Fill-in, Off
Range Wide : 0.2 ~ 3.0m, Tele : 0.25 ~ 2.0m
Recharging Time
Approx. 7 sec.
Sharpness Soft, Normal, Vivid
Effect Normal, B&W, Sepia, Negative. RGB
Auto, Daylight, Cloudy, Fluorescent_H, Fluorescent_L,
Tungsten, Custom1, Custom 2
Voice Recording (max. 1 hour)
Voice Memo in Still Image (max. 10 sec.)
Date Imprinting Date&Time, Date, Off (user selectable)
Modes : Auto, Program, A, S, M, MySET, Manual, Scene
* Scene : Night, Portrait, Children, Landscape, Close-up,
Text, Sunset, Dawn, Backlight, Fireworks,
Beach/Snow
Continuous : Single, Continuous, AEB, AFB
Self-timer : 2 sec., 10 sec., Double, Remote control
With audio (recording time : memory capacity dependent)
Size : 640x480, 320x240, 160x128
Frame rate : 30 fps, 15 fps
Digital zoom : Max. 3X
Image Sensor
Lens
Focal Length
Range
Speed
Modes
Digital Zoom
Focusing
Exposure
Flash
Shooting
Voice Recording
White Balance
Movie Clip
Still Image
Viewfinder
106
Specifications
Media SD : up to 1GB guaranteed (MMC Compatible)
Still Image : JPEG (DCF), EXIF 2.2, DPOF 1.1, PictBridge 1.0
Movie Clip : avi (MPEG-4) Audio : WAV
3072 : 3072x2304pixels, 2816 : 2816x2112pixels,
2592 : 2592x1944pixels, 2272 : 2272x1704pixels,
2048 : 2048x1536pixels, 1600 : 1600x1200pixels,
1024 : 1024x768pixels, 640 : 640x480pixels
3072 : Super fine 9 Fine 15 Normal 23 TIFF 1
2816 : Super fine 10 Fine 18 Normal 26 TIFF 1
2592 : Super fine 11 Fine 21 Normal 33 TIFF 1
2272 : Super fine 14 Fine 26 Normal 40 TIFF 2
2048 : Super fine 17 Fine 33 Normal 50 TIFF 3
1600 : Super fine 30 Fine 51 Normal 75 TIFF 4
1024 : Super fine 60 Fine 106 Normal 129 TIFF 11
640 : Super fine 121 Fine 165 Normal 202 TIFF 22
* These figures are measured under Samsung’s standard
conditions and may vary depending on shooting conditions
and camera settings.
Type Single image, Thumbnails, Slide show, Movie Clip
Editing Trimming, Resizing, Rotating
Digital output connector : USB 2.0
Audio : Mono
Video output : NTSC, PAL (user selectable)
DC power input connector : 3.3V
Primary battery : CP1(3V)
Rechargeable battery : Li-ion(SLB-1137, 3.7V, 1,130mAh)
AC Adapter : SAC - 32(DC 3.3V, 2.0A)
Dimensions (W x H x D) 105 x 56.5 x 30.2 mm
Weight Approx. 150.8g (without batteries and card)
Operating Temperature 0 ~ 40˚C
Operating Humidity 5 ~ 85%
Camera Driver
Storage Driver (Windows98/98SE/2000/ME/XP, Mac OS 9.0 ~ 10.3)
Digimax Viewer, Arcsoft PhotoImpression,
Arcsoft VideoImpression, Digimax Reader
* Specifications are subject to change without prior notice.
* All trademarks are the property of their respective owners.
Capacity
(32MB)
Image Size
Storage
Image Play
Power Source
Special Features
Software
Interface
File Format
MPEG-4 VGA 30fps Movie Clip
Text recognition(Digimax Reader included)
A World Superior Schneider Lens
Safety Flash mode
Application
6806-2432
SAMSUNG TECHWIN CO., LTD.
OPTICS & DIGITAL IMAGING DIVISION
145-3, SANGDAEWON 1-DONG, JUNGWONGU,
SUNGNAM-CITY, KYUNGKI-DO, KOREA
462-121
TEL : (82) 31-740-8086,8088, 8090, 8092, 8099
FAX : (82) 31-740-8398, 8111
www.samsungcamera.com
SAMSUNG OPTO-ELECTRONICS AMERICA, INC.
HEADQUARTERS
40 SEAVIEW DRIVE, SECAUCUS, NJ07094, U.S.A.
TEL : (1) 201-902-0347
FAX : (1) 201-902-9342
WESTERN REGIONAL OFFICE
18600 BROADWICK ST.,
RANCHO DOMINGUEZ, CA 90220, U.S.A.
TEL : (1) 310-900-5263/5264
FAX : (1) 310-537-1566
www.samsungcamerausa.com
SAMSUNG OPTO-ELECTRONICS UK LIMITED
SAMSUNG HOUSE
1000 HILLSWOOD DRIVE
HILLSWOOD BUSINESS PARK
CHERTSEY KT16 OPS U.K.
TEL : 00800 12263727
(free for calls from UK only)
SERVICE HOTLINE : 01932455320
www.samsungcamera.co.uk
SAMSUNG OPTO-ELECTRONICS GMBH
AM KRONBERGER HANG 6
D-65824 SCHWALBACH/TS., GERMANY
TEL : (49) 6196 66 53 03
FAX : (49) 6196 66 53 66
www.samsungcameras.de
SAMSUNG FRANCE S.A.S.
BP 51 TOUR MAINE MONTPARNASSE
33, AV .DU MAINE
75755, PARIS CEDEX 15, FRANCE
HOTLINE PHOTO NUMÉRIQUE :
00 800 22 26 37 27(Numéro Vert-Appel Gratuit)
TEL : (33) 1-4279-2200
FAX : (33) 1-4538-6858
www.samsungphoto.fr
SAMSUNG TECHWIN MOSCOW OFFICE
RUSSIA, 125167, MOSCOW LENNINGRADSKY,
PR-KT, 37-A, KORP14
TEL : (7) 095-258-9299/96/98
FAX : (7) 095-258-9297
http://www.samsungcamera.ru
TIANJIN SAMSUNG OPTO-ELECTRONICS CO.,LTD.
7 PINGCHANG ROAD NANKAI DIST., TIANJIN
P.R CHINA
POST CODE:300190
TEL : (86) 22-2761-8867
FAX : (86) 22-2761-8864
www.samsungcamera.com.cn
Internet address - http : //www.samsungcamera.com/
The CE Mark is a Directive conformity
mark of the European Community (EC)