Hanwha Techwin PRO815 Digital Camera User Manual H1 en 136 v03

Download:
Mirror Download [FCC.gov]
Document ID	572126
Application ID	xdcXJmLHCkRxf0uFSVtusA==
Document Description	Users Manual 7 of 7
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	246.57kB (3082107 bits)
Date Submitted	2005-08-16 00:00:00
Date Available	2005-08-16 00:00:00
Creation Date	2005-07-29 22:22:31
Producing Software	Acrobat Distiller 5.0.2 (Macintosh)
Document Lastmod	2005-07-29 22:26:11
Document Title	H1_en_136_v03
Document Creator	QuarkXPress(MAC): LaserWriter 8 8.3fc2
Document Author:	samyoung

Software Notes
Please ensure that you read the instruction manual carefully before use.
ㆍThe attached software is a camera driver and image editing software tool for Windows.
ㆍUnder no circumstances should all or part of either the software or the user manual be
reproduced.
ㆍCopyrights for software are licensed only for use with a camera.
ㆍIn the unlikely event of a manufacturing fault, we will repair or exchange your camera.
We cannot, however, be held responsible in any way for damage caused by inappropriate use.
ㆍUsing a Hand-made PC or a PC and OS that has not been guaranteed by the manufacturer
is not covered by the Samsung warranty.
ㆍBefore reading this manual, you should have a basic knowledge of computers and O/S
(Operating Systems).
System Requirements
For Windows
PC with processor better than MMX
For Macintosh
Power Mac G3 or later
Pentium 233MHz (XP : Pentium II 300MHz)
Windows 98/98SE/2000/ME/XP
Mac OS 9.2 ~ 10.3
Minimum 32MB RAM (XP : 128MB)
Minimum 64MB RAM
140MB of available hard-disk space
110MB of available hard-disk space
USB port
USB port
CD-ROM drive
CD-ROM drive
800x600 pixels, 16-bit colour display
QuickTime player
compatible monitor (24-bit color display
DivX(for movie clip)
recommended)
《136》
About the software
After inserting the software CD provided with this camera into the CD-ROM drive, the following
window should automatically run.
Before connecting the camera to the PC,
you should first install the camera driver.
■ Camera driver : This enables images to transfer between the camera and PC.
This camera uses the USB Storage Driver as the camera driver. You can use the camera as
a USB card reader. After installing the driver and connecting this camera to the PC, you can
find [Removable Disk] in [Windows Explorer] or [My computer]. A USB Storage Driver is
provided only for Windows. A USB Driver for MAC is not included with the Application CD.
But you can use the camera with Mac OS 9.2 ~ 10.3.
■ Digimax Master : This is the all-in-on multi media software solution
You can download, view, edit and save your digital image and movie clip with this software.
This software is only compatible with Windows.
■ Digimax Reader : Text recognition program
You can save an image file that was captured in the TEXT mode as a text file with this
program. This software is only compatible with Windows.
INFORMATION
● Be sure to check the system requirements before installing the driver.
● You should allow 5~10 seconds for running the automatic setup program according to the
capability of the computer. If the frame does not show, run the [Windows Explorer] and
select [Samsung.exe] in the CD-ROM Drive root directory.
《137》
Setting up the application software
To use this camera with a PC, install the application software first.
After this has been done, the stored images in the camera can be moved to the PC and can be
edited by an image editing program.
INFORMATION
● Close other programs before installing the application software.
● Before installing the application software, disconnect the USB connection.
You can visit the Samsung web-site through the internet.
http://www.samsungcamera.com : English
http://www.samsungcamera.co.kr : Korean
1. Click the [Install] menu in the Auto run frame.
The camera driver is installed automatically.
[Click !]
2. Installation is complete.
Click the [Finish] button.
[Click !]
3. The Software License Agreement window for
DirectX will be displayed.
If you agree to this, select [I accept the agreement]
and click [Next >] button. the window will then
move to the next step. If you disagree, select
[I do not accept the agreement] and click [Cancel]
button.
The installation program will be cancelled.
《138》
[Click !]
Setting up the application software
4. A window will open. Click the [Next(N) >] button.
[Click !]
5. DirectX Installation is completed.
Click the [Finish] button and Digimax Master
installation will be started.
* The system will not reboot even if the [Yes,
I want to restart the computer now] option is
selected.
* The screen shot of step 5 can be different
with the illustration according to the system
requirements.
[Click !]
6. A window where you can choose the program you
want to install will appear. Click [Install].
For information on application software, please refer to
page 104, 105.
[Click !]
INFORMATION
● If you select [Exit] at step 6, the application program installation will be cancelled.
7. The Digimax Master installation window will be
displayed as shown alongside. Click the [Next >]
button.
[Click !]
《139》
Setting up the application software
8. A window will open. Click the [Next >] button.
[Click !]
INFORMATION
● If you select [Cancel] at step 8, a window for installing Digimax Reader will be displayed.
9. A destination selection window will open. Click [Next >].
To copy to the files to another folder, click [Browse..]
and choose a folder you want.
[Click !]
10. A window will open, asking you to choose a folder to
which program icons will be added. Click [Next >] button.
If you want to choose another folder, click [Browse..] and
choose a folder you want.
[Click !]
11. Click [Install(I)] button and Digimax Master starts installing.
[Click !]
《140》
Setting up the application software
12. Digimax Master installation is successfully completed.
Click the [Finish] button to install Digimax Reader.
* The screen shot of step 12 can be different with the
illustration according to the system requirements.
[Click !]
13. A window will be displayed as shown alongside.
Click the [INSTALL] button.
- Check the [MANUAL] button. Instructions for using
Digimax reader will be displayed.
- Click the [EXIT] button and Digimax reader
installation will be cancelled and a window for
restarting the computer.
[Click !]
14. A window will open. Click the [Next >] button.
[Click !]
15. The Software License Agreement window will be
displayed. If you agree to this, click [Yes],
the window will then move to the next step.
If you disagree, click [No] and the installation
program will be cancelled.
[Click !]
《141》
Setting up the application software
16. A destination selection window will open.
Click [Next >].
To copy to the files to another folder, click
[Browse...] and choose a folder you want.
[Click !]
17. Digimax Reader Installation is completed.
To apply changes, you must restart the computer.
Select [Yes, I want to restart my computer now],
and then click [Finish].
[Click !]
18. The screen shot of step 17 can be different with the
illustration according to the system requirements.
Click [Finish] button to restart the computer.
[Click !]
19. After restarting the computer, connect the PC to the camera with the USB cable.
20. Turn the camera power on.
[Found New Hardware Wizard] will open and the
computer will recognise the camera.
* If your OS is Windows XP, an image viewer
program will open.
If the download window of Digmax Master opens,
the camera driver was setup successfully.
《142》
Setting up the application software
21. If you can see [Removable Disk] under [My computer],
the camera driver installation was successful.
Now you can transfer image files from the camera to
PC via the USB cable.
INFORMATION
● If you have installed the camera driver, [Found New Hardware Wizard] may not open.
● On a Windows 98 or 98 SE system, the Found New Hardware Wizard dialog box opens
and a window asking you to select a driver file may appear. In this case, specify "USB
Driver" in the CD supplied. (for Windows 98 and 98 SE).
● Before connecting the camera to the PC, You should first install the camera driver.
● After installing the camera driver, you have to restart your PC.
● If you connect the camera to the PC before installing the camera driver, the [Found New
Hardware Wizard] will open.
In this case, cancel the [Found New Hardware Wizard] and disconnect the camera.
Install the camera driver and connect the camera to the PC again.
● Should the computer not find the camera driver after installation, please try one or more
of the following measures.
1. Delete the camera driver (p.123), and re-install the driver.
2. Refer to FAQ (p.132) to check for a possible solution to the problem.
3. If your PC’s central processing unit is VIA chip (This is shown in the USB Host
Controller), download the patch file from the Samsung Camera web page.
(http://www.samsungcamera.com)
《143》
Starting PC mode
• If you connect the USB cable to a USB port on your PC and then turn on the power,
the camera will automatically switch to "computer connection mode".
• In this mode, you can download stored images to your PC through the USB cable.
• The LCD monitor is always turned off in PC mode.
• The card access lamp will blink when the files are transferring via the USB connection.
■ Connecting the camera to a PC
1. Turn the PC power on.
2. Turn the camera power on.
3. Press the Menu button and select the [
] menu tab by
Video Out
pressing the Up/ Down button.
Quick View
4. Press the Right button and select the [USB] menu by
Auto Rotating
USB
Computer
pressing the Up/ Down button.
Printer
Reset All
5. Press the Right button and select a desired sub menu by
File
pressing the Up/ Down button.
Power Off
6. Select the [Computer] menu and press the OK button.
7. Connect the PC and the camera via the USB cable.
- Insert the small plug of the USB cable into the camera USB connection terminal.
- Insert the large connector of the USB cable into the USB port of the PC.
- The plugs must be firmly inserted.
※ If you selected [Printer] in Step 6, when you
connect the camera to your computer, the
[Connecting Printer] message will be displayed
on the LCD monitor and the connection will not
be established. In this case, disconnect the
USB cable, and then follow the procedure
from Step 3 and onward.
■ Disconnecting the camera and PC : Refer to page 125 (Removing the removable disk).
INFORMATION
● The camera driver must be installed before using PC mode.
● To save battery power, it is recommended that you use an AC adapter (Optional) when
connecting the camera to a computer.
《144》
Starting PC mode
■ Downloading stored images
You can download the still images stored on the camera to your PC's hard disk and print
them or use a photo editing software to edit them.
1. Connect the camera to your PC with the USB cable.
2. On your computer's desktop display, select
[My computer] and double click [Removable Disk
→ DCIM → 100SSCAM].
The image files will then be displayed.
3. Select an image and press the right mouse button.
4. A pop-up menu will open.
Click [Cut] or [Copy] menu.
- [Cut] : cuts a selected file.
- [Copy] : copies files.
5. Click a folder where you want to paste the file.
《145》
Starting PC mode
6. Press the right mouse button and a pop-up menu
will open. Click [Paste].
7. An image file is transferred from the camera to
your PC.
- By using [Digimax Viewer], you can see the stored images in the memory directly on the
PC monitor and you can copy or move the image files.
《146》
Removing the USB Driver for Windows 98SE
■ To remove the USB driver, refer to the process shown below.
1. Trace [Start → Settings] and click [Control Panel].
2. Double-click [Add/Remove programs].
3. The [Add/Remove Programs Properties] window
will open.
Click [Pro 815] and click the [Add/Remove] button.
[Click !]
4. Uninstallation is complete.
Click the [Finish] button and the window will disappear.
[Click !]
《147》
Removable Disk
■ To use this camera as a Removable Disk, install (p.110) the USB Driver.
1. Before turning the camera power on, connect the camera to the PC with the USB cable.
2. Click [Removable Disk ] under [My Computer] or [Windows Explorer].
3. Image files stored in the Removable Disk (DCIM →100SSCAM) can be transferred to the PC.
INFORMATION
Important information whilst using the Removable Disk
● The [Removable Disk] indicator will not show when the camera power is off or the USB
cable is removed.
● We recommend that you should copy the images to the PC to view them. Opening
images directly from the removable disk may be subject to unexpected disconnection.
● When uploading images from the PC to the camera, ensure that the uploaded file names
are not the same as those already stored on the memory.
● When you upload a file that is not taken by this
camera to Removable Disk, the [File Error!]
message will be displayed on the LCD monitor in the
PLAY mode, and nothing is displayed in
THUMBNAIL mode.
● The card access lamp will blink, when a file is
transferred (copy or deletion) between the PC and
the camera. Do not remove the USB cable until the lamp stops blinking. To remove the USB
cable in Windows 2000/ME/XP, use the [Unplug or Eject Hardware] icon on the task bar.
《148》
Removing the removable disk
■ Windows 98/ 98SE
1. Check whether the camera and PC are transferring a file. If the card access lamp blinks,
you have to wait until the lamp is turned off.
2. Unplug the USB cable.
■ Windows 2000/ ME/ XP
(The illustrations may be different from the real display in accordance with the Windows O/S.)
1. Check whether the camera and PC are transferring a file. If the auto focus lamp blinks, you
have to wait until the lamp is turned off.
2. Double-click the [Unplug or Eject Hardware]
icon on the task bar.
[Double-click!]
3. The [Unplug or Eject Hardware] window will
open. Select the [USB Mass Storage
Device] and click the [Stop] button.
[Click !]
4. The [Stop a Hardware device] window will
open. Select the [USB Mass Storage
Device] and click the [OK] button.
[Click !]
5. A [Safe to Remove Hardware] window will
open. Click the [OK] button.
[Click !]
《149》
Removing the removable disk
6. A [Unplug or Eject Hardware] window will open.
Click the [Close] button and the removable disk
will be removed safely.
7. Unplug the USB cable.
[Click !]
Setting up the USB Driver for MAC
1. A USB Driver for MAC is not included with the software CD as MAC OS supports the
camera driver.
2. Check the MAC OS. This camera is compatible with MAC OS 10.0 or later.
3. Connect the camera to the Macintosh and turn the camera power on.
4. A new icon will be displayed on the desktop after connecting the camera to the MAC.
Using the USB Driver for MAC
1. Double click a new icon on the desktop and the folder in the memory will be displayed.
2. Select an image file and copy or move it to MAC.
CAUTION
● For Mac OS 10.0 or later : First complete uploading from computer to camera and then
remove the removable disk with the Extract command.
● If a movie clip can’t play back on the Mac OS, please visit the following site.
http://www.divx.com/divx/mac/
《150》
Digimax Master
■ You can download, view, edit and save your digital image and movie clip with this software.
This software is only compatible with Windows.
■ To start the program, click [Start → Programs → Samsung → Digimax Master].
● Downloading images
1. Connect the camera to your PC.
2. A window for downloading images will display after
connecting the camera and your PC.
- To download the captured images, select the [All(A)]
button.
- Select desired folder in the window and click the
[All(A)] button. You can save captured images and
selected folder.
- If you click the [Cancel] button, downloading will be
cancelled.
[Click !]
3. Click [Next(N) >] button.
[Click !]
《151》
Digimax Master
4. Select a destination and make a folder to save
downloaded images and folder.
- Folders will be made in order of date and images will
be downloaded.
- Folder name will be made as you want and images
will be downloaded.
- After selecting a folder that was made before,
images will be downloaded.
5. Click [Next(N) >] button.
[Click !]
6. A window will open as shown alongside.
The destination of selected folder will be displayed
on the upper side of the window. Click the [Start]
button to download the images.
[Click !]
7. Downloaded images will be displayed.
《152》
Digimax Master
● Image viewer : You can view the stored images.
①
⑤
⑥
⑦
②
③
④
- Image viewer functions are listed below.
① Menu bar : You can select menus.
File, Edit, View, Tools, Change functions, Auto download, help, etc.
② Image selection window : You can select desired image in this window.
③ Media type selection menu : You can select image viewer, image edit, movie clip edit
function in this menu.
④ Preview window : You can preview a image or a movie clip and check the multi media
information.
⑤ Zoom bar : You can change preview size.
⑥ Folder display window : You can see folder location of selected image.
⑦ Image display window : Images of selected folder are displayed.
※ Refer to the [Help] menu in Digimax Master for further information.
《153》
Digimax Master
● Image edit : You can edit the still image.
①
④
②
③
- Image edit functions are listed below.
① Edit menu : You can select the following menus.
[Tools] : You can resize or crop the selected image. See the [Help] menu.
[Modify] : You can modify image quality. See the [Help] menu.
[Retouch] : You can change image or insert effects on the image. See the [Help] menu.
② Drawing tools : Tools for editing an image.
③ Image display window : a selected image displays in this window.
④ Preview window : You can preview the changed image.
※ Refer to the [Help] menu in Digimax Master for further information.
《154》
Digimax Master
● Movie edit : You can get the still image, movie clip, narration, music files together in a movie clip.
①
②
- Movie clip edit functions are listed below.
① Edit menu : You can select the following menus.
[Add] : You can add a desired multi media in a movie clip.
[Edit] : You can change the brightness, contrast, colour and saturation.
[Effect] : You can insert an effect.
[Text] : You can insert texts.
[Narration] : You can insert a narration.
[Make] : You can save the edited multi media as a new file name.
② Frame display window : You can insert multi media in this window.
※ Refer to the [Help] menu in Digimax Master for further information.
《155》
Digimax Master
■ Digimax Reader is a Text recognition program. You can save an image file that is captured in
the Text mode, as a text file with this program.
This software is only compatible with Windows.
■ To start the program, click [Start → Programs → Digimax Reader Eng].
The following screen will appear.
■ How to use the Digimax Reader
1. Connect the camera and the PC with a USB cable and download the images that were
stored in the camera to the PC.
* Please see page 120 ~ 122 for details on Connecting a camera and PC, Downloading
images.
2. Run the Digimax Reader.
3. Click the Open(
《156》
) icon as shown alongside.
Digimax Master
4. Select the image you want to save as a text file.
* Only an image that was taken with SAMSUNG
camera can be opened.
5. Click the Area Analysis(
) icon to scan the image.
6. Part of the image you selected will be displayed as
shown.
7. Click the Character Recognition(
) icon.
The part selected in the previous step will be
recognized as text.
8. To save the section as a text, click the Save(
icon. A window as shown alongside will be
displayed.
《157》
Digimax Master
9. Select a file type that you want to.
Selectable file type : *.TXT, *.HWP, *.DOC, *.RTF
INFORMATION
● To get an image that can be recognized as a text :
- Keep a distance of 20cm between the subject and the camera.
- The subject need to be centered.
- Avoid the camera shake to get a good image.
● Refer to the [Help] menu in Digimax Reader for further information.
FAQ
■ Please check the following if the USB connection malfunctions.
[Case 1]
The camera power is off.
→ Turn the camera power on. We recommend using an AC power adapter in PC
mode.
[Case 2]
USB Driver is not installed correctly.
→ Install the USB Driver correctly. Refer to page 110.
[Case 3]
The USB cable is not connected or you are using a cable with an incorrect
specification.
→ Use a USB cable with the correct specification.
[Case 4]
The camera is not recognized by your PC.
Sometimes, the camera may appear under [Unknown Devices] in Device
Manager.
→ Install the camera driver correctly.
Turn off the camera, remove the USB cable, plug in the USB cable again, and
then turn on the camera.
《158》
FAQ
[Case 5]
There is an unexpected error during file transfer
→ Turn the camera power off and on again. Transfer the file again.
[Case 6]
How do I know my computer supports a USB Interface?
→ Check the USB port in your computer or keyboard.
→ Check the OS version. A USB Interface is available in Windows 98, 98SE,
2000, ME .XP.
→ Check [Universal Serial Bus controllers] in Device Manager. Do the following to
check [Universal Serial Bus controllers].
Win 98/ME
: Trace [Start → Settings → Control Panel → System →
Device Manager → Universal Serial Bus controllers].
Win 2000
: Trace [Start → Settings → Control Panel → System →
Hardware → Device Manager → Universal Serial Bus
controllers].
Win XP
: Trace [Start → Control Panel → Performance and
Maintenance → System → Hardware → Device Manager →
Universal Serial Bus controllers].
There must be USB Host Controller and USB root hub under [Universal Serial
Bus controllers].
In addition, double-click on the USB Universal Host Controller and the USB
Root Hub to check if the Device Status states "This device is working properly".
If the Device Status says the device is "not working properly", click the "Driver"
tab and then click [Update Driver] or [Reinstall Driver].
→ When all the conditions mentioned above are met, the computer can support
the USB interface.
[Case 7]
When using the USB hub.
→ There may be a problem in connecting the camera to the PC through the USB
hub if the PC and the hub are not compatible. Wherever possible, connect the
camera to the PC directly.
[Case 8]
Are other USB cables connected to the PC?
→ The camera may malfunction when it is connected to the PC at the same time
as another USB cable. In this case, disconnect the other USB cable, and
connect only one USB cable to the camera.
《159》
FAQ
[Case 9]
When I open the Device Manager (by clicking Start → (Settings) → Control
Panel → (Performance and Maintenance) → System → (Hardware) → Device
Manager), there are「Unknown Devices」or「Other Devices」entries with a
yellow question mark(?) beside them or devices with an exclamation mark(!)
beside them.
→ Right-click on the entry with the question(?) or exclamation (!) mark and select
"Remove". Restart the PC and connect the camera the again. For Windows 98
PC, remove the camera driver also, restart the PC, and then reinstall the
camera driver.
→ Double-click on the entry with the question (?) or exclamation (!) mark, click the
"Driver" tab, and click [Update Driver] or [Reinstall Driver]. If a message appears
asking you to specify the location of the appropriate device driver, specify "USB
Driver" in the CD supplied.
[Case 10]
In some security programs (Norton Anti Virus, V3, etc.), the computer may not
recognise the camera as a removable disk.
→ Stop the security programs and connect the camera to the computer. Refer to
the security program instructions about how to stop the program.
■ When the movie clip doesn’t play back on the PC
※ When the movie clip recorded by the camera doesn’t play back on the PC, the causes are
mostly due to the codec installed on the PC.
● When the DirectX 9.0 or later is not installed
→ Install the DirectX 9.0 or later
1) Insert the CD provided with the camera
2) Run the windows explorer and select [CD-ROM drive:\ USB Driver\DirectX 9.0] folder and
click the DXESETUP.exe file.The DirectX will be installed. Visit the following site for
downloading the DirectX.http://www.microsoft.com/directx
《160》
FAQ
■ If a PC (Windows 98) stops responding while the camera and PC are connected repeatedly
→ If a PC (Windows 98) is turned on for a long time and connect the camera repeatedly, the
PC may not recognise the camera. In this case, re-start the PC.
■ If a PC connected with the camera stops responding while Windows is starting.
→ In this case, disconnect the PC and the camera and Windows will start.
If the problem happens continuously, set the Legacy USB Support to disable and re-start
the PC. The Legacy USB Support is in the BIOS setup menu. (The BIOS setup menu
differs from the PC manufacturers and some BIOS menus don’t have Legacy USB
Support) If you can’t change the menu by yourself, contact to the PC manufacturer or
BIOS manufacturer.
■ If the movie clip can’t be deleted, removable disk can’t be extracted or an error message
displays during the file transfer.
→ If you install only the Digimax Viewer, the problems mentioned above occasionally happen.
- Close the Digimax Viewer program by clicking the Digimax Viewer icon on the Taskbar.
- Install all the application programs included in the software CD.
(You must install the Movie clip codec)
《161》
SAMSUNG TECHWIN CO., LTD.
OPTICS & DIGITAL IMAGING DIVISION
145-3, SANGDAEWON 1-DONG, JUNGWONGU,
SUNGNAM-CITY, KYUNGKI-DO, KOREA
462-121
TEL : (82) 31-740-8086,8088, 8090, 8092, 8099
FAX : (82) 31-740-8398, 8111
www.samsungcamera.com
SAMSUNG OPTO-ELECTRONICS AMERICA, INC.
HEADQUARTERS
40 SEAVIEW DRIVE, SECAUCUS, NJ07094, U.S.A.
TEL : (1) 201-902-0347
FAX : (1) 201-902-9342
WESTERN REGIONAL OFFICE
18600 BROADWICK ST.,
RANCHO DOMINGUEZ, CA 90220, U.S.A.
TEL : (1) 310-900-5263/5264
FAX : (1) 310-537-1566
www.samsungcamerausa.com
SAMSUNG OPTO-ELECTRONICS UK LIMITED
SAMSUNG HOUSE
1000 HILLSWOOD DRIVE
HILLSWOOD BUSINESS PARK
CHERTSEY KT16 OPS U.K.
TEL : 00800 12263727
(free for calls from UK only)
UK Service Hotline : 01932455320
www.samsungcamera.co.uk
SAMSUNG OPTO-ELECTRONICS GMBH
AM KRONBERGER HANG 6
D-65824 SCHWALBACH/TS., GERMANY
TEL : (49) 6196 66 53 03
FAX : (49) 6196 66 53 66
www.samsungcameras.de
SAMSUNG FRANCE S.A.S.
BP 51 TOUR MAINE MONTPARNASSE
33, AV .DU MAINE
75755, PARIS CEDEX 15, FRANCE
HOTLINE PHOTO NUMÉRIQUE :
00 800 22 26 37 27(Numéro Vert-Appel Gratuit)
TEL : (33) 1-4279-2200
FAX : (33) 1-4538-6858
www.samsungphoto.fr
SAMSUNG TECHWIN MOSCOW OFFICE
RUSSIA, 125167, MOSCOW LENNINGRADSKY,
PR-KT, 37-A, KORP14
TEL : (7) 095-258-9299/96/98
FAX : (7) 095-258-9297
http://www.samsungcamera.ru
TIANJIN SAMSUNG OPTO-ELECTRONICS CO.,LTD.
7 PINGCHANG ROAD NANKAI DIST., TIANJIN
P.R CHINA
POST CODE:300190
TEL : (86) 22-2761-8867
FAX : (86) 22-2761-8864
www.samsungcamera.com.cn
＊ Internet address - http : //www.samsungcamera.com/
The CE Mark is a Directive conformity
mark of the European Community (EC)
2008. 4. 24
6806-2415

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 2005:07:29 22:22:31+09:00
Modify Date                     : 2005:07:29 22:26:11+09:00
Page Count                      : 27
Creation Date                   : 2005:07:29 13:22:31Z
Mod Date                        : 2005:07:29 13:22:31Z
Producer                        : Acrobat Distiller 5.0.2 (Macintosh)
Author                          : samyoung
Metadata Date                   : 2005:07:29 13:22:31Z
Creator                         : samyoung
Title                           : H1_en_136_v03

EXIF Metadata provided by EXIF.tools