Hanwha Techwin PRO815 Digital Camera User Manual H1 en 136 v03

Samsung Techwin Co Ltd Digital Camera H1 en 136 v03

Users Manual 7 of 7

《136》Please ensure that you read the instruction manual carefully before use.ㆍThe attached software is a camera driver and image editing software tool for Windows.ㆍUnder no circumstances should all or part of either the software or the user manual bereproduced.ㆍCopyrights for software are licensed only for use with a camera.ㆍIn the unlikely event of a manufacturing fault, we will repair or exchange your camera.We cannot, however, be held responsible in any way for damage caused by inappropriate use.ㆍUsing a Hand-made PC or a PC and OS that has not been guaranteed by the manufacturer is not covered by the Samsung warranty.ㆍBefore reading this manual, you should have a basic knowledge of computers and O/S(Operating Systems).System RequirementsFor Windows For MacintoshPower Mac G3 or laterWindows 98/98SE/2000/ME/XP Mac OS 9.2 ~ 10.3Minimum 32MB RAM (XP : 128MB) Minimum 64MB RAM140MB of available hard-disk space 110MB of available hard-disk spaceUSB port USB portCD-ROM drive CD-ROM driveQuickTime playerDivX(for movie clip)PC with processor better than MMX Pentium 233MHz (XP : Pentium II 300MHz)800x600 pixels, 16-bit colour displaycompatible monitor (24-bit color displayrecommended)Software Notes
《137》After inserting the software CD provided with this camera into the CD-ROM drive, the followingwindow should automatically run.Before connecting the camera to the PC,you should first install the camera driver.■Camera driver : This enables images to transfer between the camera and PC.This camera uses the USB Storage Driver as the camera driver. You can use the camera asa USB card reader. After installing the driver and connecting this camera to the PC, you canfind [Removable Disk] in [Windows Explorer] or [My computer]. A USB Storage Driver isprovided only for Windows. A USB Driver for MAC is not included with the Application CD.But you can use the camera with Mac OS 9.2 ~ 10.3.■Digimax Master : This is the all-in-on multi media software solutionYou can download, view, edit and save your digital image and movie clip with this software.This software is only compatible with Windows.■Digimax Reader : Text recognition programYou can save an image file that was captured in the TEXT mode as a text file with thisprogram. This software is only compatible with Windows.●Be sure to check the system requirements before installing the driver.●You should allow 5~10 seconds for running the automatic setup program according to thecapability of the computer. If the frame does not show, run the [Windows Explorer] andselect [Samsung.exe] in the CD-ROM Drive root directory.INFORMATIONAbout the software
《138》To use this camera with a PC, install the application software first.After this has been done, the stored images in the camera can be moved to the PC and can beedited by an image editing program.You can visit the Samsung web-site through the internet.http://www.samsungcamera.com : Englishhttp://www.samsungcamera.co.kr : Korean1. Click the [Install] menu in the Auto run frame.The camera driver is installed automatically.●Close other programs before installing the application software.●Before installing the application software, disconnect the USB connection.INFORMATION2. Installation is complete.Click the [Finish] button.3. The Software License Agreement window forDirectX will be displayed.If you agree to this, select [I accept the agreement]and click [Next >] button. the window will thenmove to the next step. If you disagree, select [I do not accept the agreement] and click [Cancel]button.The installation program will be cancelled.[Click !][Click !][Click !]Setting up the application software
《139》6. A window where you can choose the program youwant to install will appear. Click [Install].For information on application software, please refer topage 104, 105.7. The Digimax Master installation window will bedisplayed as shown alongside. Click the [Next >]button.4. A window will open. Click the [Next(N) >] button.5. DirectX Installation is completed.Click the [Finish] button and Digimax Masterinstallation will be started.* The system will not reboot even if the [Yes, I want to restart the computer now] option isselected.* The screen shot of step 5 can be differentwith the illustration according to the systemrequirements.●If you select [Exit] at step 6, the application program installation will be cancelled.INFORMATION[Click !][Click !][Click !][Click !]Setting up the application software
《140》8. A window will open. Click the [Next >] button.9. A destination selection window will open. Click [Next >].To copy to the files to another folder, click [Browse..]and choose a folder you want.11. Click [Install(I)] button and Digimax Master starts installing.10. A window will open, asking you to choose a folder towhich program icons will be added. Click [Next >] button.If you want to choose another folder, click [Browse..] andchoose a folder you want.●If you select [Cancel] at step 8, a window for installing Digimax Reader will be displayed.INFORMATION[Click !][Click !][Click !][Click !]Setting up the application software
《141》13. A window will be displayed as shown alongside.Click the [INSTALL] button.- Check the [MANUAL] button. Instructions for usingDigimax reader will be displayed.- Click the [EXIT] button and Digimax readerinstallation will be cancelled and a window forrestarting the computer.14. A window will open. Click the [Next >] button.[Click !]15. The Software License Agreement window will bedisplayed. If you agree to this, click [Yes],the window will then move to the next step.If you disagree, click [No] and the installationprogram will be cancelled.12. Digimax Master installation is successfully completed.Click the [Finish] button to install Digimax Reader.* The screen shot of step 12 can be different with theillustration according to the system requirements.[Click !][Click !][Click !]Setting up the application software
《142》16. A destination selection window will open.Click [Next >].To copy to the files to another folder, click[Browse...] and choose a folder you want.[Click !]17. Digimax Reader Installation is completed.To apply changes, you must restart the computer.Select [Yes, I want to restart my computer now],and then click [Finish].18. The screen shot of step 17 can be different with theillustration according to the system requirements.Click [Finish] button to restart the computer.19. After restarting the computer, connect the PC to the camera with the USB cable.20. Turn the camera power on.[Found New Hardware Wizard] will open and thecomputer will recognise the camera.* If your OS is Windows XP, an image viewerprogram will open.If the download window of Digmax Master opens,the camera driver was setup successfully.[Click !][Click !]Setting up the application software
《143》●If you have installed the camera driver, [Found New Hardware Wizard] may not open.●On a Windows 98 or 98 SE system, the Found New Hardware Wizard dialog box opensand a window asking you to select a driver file may appear. In this case, specify "USBDriver" in the CD supplied. (for Windows 98 and 98 SE).●Before connecting the camera to the PC, You should first install the camera driver.●After installing the camera driver, you have to restart your PC.●If you connect the camera to the PC before installing the camera driver, the [Found NewHardware Wizard] will open.In this case, cancel the [Found New Hardware Wizard] and disconnect the camera.Install the camera driver and connect the camera to the PC again.●Should the computer not find the camera driver after installation, please try one or moreof the following measures.1. Delete the camera driver (p.123), and re-install the driver.2. Refer to FAQ (p.132) to check for a possible solution to the problem.3. If your PC’s central processing unit is VIA chip (This is shown in the USB HostController), download the patch file from the Samsung Camera web page.(http://www.samsungcamera.com)INFORMATION21. If you can see [Removable Disk] under [My computer],the camera driver installation was successful.Now you can transfer image files from the camera toPC via the USB cable.Setting up the application software
《144》•If you connect the USB cable to a USB port on your PC and then turn on the power,the camera will automatically switch to "computer connection mode".•In this mode, you can download stored images to your PC through the USB cable.•The LCD monitor is always turned off in PC mode.•The card access lamp will blink when the files are transferring via the USB connection.■Connecting the camera to a PC1. Turn the PC power on.2. Turn the camera power on.3. Press the Menu button and select the [ ] menu tab bypressing the Up/ Down button. 4. Press the Right button and select the [USB] menu bypressing the Up/ Down button.5. Press the Right button and select a desired sub menu bypressing the Up/ Down button.6. Select the [Computer] menu and press the OK button.7. Connect the PC and the camera via the USB cable.- Insert the small plug of the USB cable into the camera USB connection terminal.- Insert the large connector of the USB cable into the USB port of the PC.- The plugs must be firmly inserted.●The camera driver must be installed before using PC mode.●To save battery power, it is recommended that you use an AC adapter (Optional) whenconnecting the camera to a computer.INFORMATION■Disconnecting the camera and PC : Refer to page 125 (Removing the removable disk).※If you selected [Printer] in Step 6, when youconnect the camera to your computer, the[Connecting Printer] message will be displayedon the LCD monitor and the connection will notbe established. In this case, disconnect theUSB cable, and then follow the procedurefrom Step 3 and onward.Video OutQuick ViewAuto RotatingUSBReset AllFilePower OffComputerPrinterStarting PC mode
《145》3. Select an image and press the right mouse button.4. A pop-up menu will open.Click [Cut] or [Copy] menu.- [Cut] : cuts a selected file.- [Copy] : copies files.■Downloading stored imagesYou can download the still images stored on the camera to your PC's hard disk and printthem or use a photo editing software to edit them.1. Connect the camera to your PC with the USB cable.2. On your computer's desktop display, select[My computer] and double click [Removable Disk→DCIM →100SSCAM].The image files will then be displayed.5. Click a folder where you want to paste the file.Starting PC mode
《146》6. Press the right mouse button and a pop-up menuwill open. Click [Paste].7. An image file is transferred from the camera toyour PC.- By using [Digimax Viewer], you can see the stored images in the memory directly on thePC monitor and you can copy or move the image files.Starting PC mode
《147》■To remove the USB driver, refer to the process shown below.1. Trace [Start →Settings] and click [Control Panel].4. Uninstallation is complete.Click the [Finish] button and the window will disappear.2. Double-click [Add/Remove programs].3. The [Add/Remove Programs Properties] windowwill open.Click [Pro 815] and click the [Add/Remove] button.[Click !][Click !]Removing the USB Driver for Windows 98SE
《148》■To use this camera as a Removable Disk, install (p.110) the USB Driver.1. Before turning the camera power on, connect the camera to the PC with the USB cable.2. Click [Removable Disk ] under [My Computer] or [Windows Explorer].3. Image files stored in the Removable Disk (DCIM →100SSCAM) can be transferred to the PC.Important information whilst using the Removable Disk●The [Removable Disk] indicator will not show when the camera power is off or the USBcable is removed.●We recommend that you should copy the images to the PC to view them. Openingimages directly from the removable disk may be subject to unexpected disconnection.●When uploading images from the PC to the camera, ensure that the uploaded file namesare not the same as those already stored on the memory.●When you upload a file that is not taken by thiscamera to Removable Disk, the [File Error!]message will be displayed on the LCD monitor in thePLAY mode, and nothing is displayed inTHUMBNAIL mode.●The card access lamp will blink, when a file istransferred (copy or deletion) between the PC and the camera. Do not remove the USB cable until the lamp stops blinking. To remove the USBcable in Windows 2000/ME/XP, use the [Unplug or Eject Hardware] icon on the task bar.INFORMATIONRemovable Disk
《149》[Click !][Double-click!][Click !][Click !]■Windows 98/ 98SE1. Check whether the camera and PC are transferring a file. If the card access lamp blinks,you have to wait until the lamp is turned off.2. Unplug the USB cable.■Windows 2000/ ME/ XP(The illustrations may be different from the real display in accordance with the Windows O/S.)1. Check whether the camera and PC are transferring a file. If the auto focus lamp blinks, youhave to wait until the lamp is turned off.2. Double-click the [Unplug or Eject Hardware]icon on the task bar.3. The [Unplug or Eject Hardware] window willopen. Select the [USB Mass StorageDevice] and click the [Stop] button.4. The [Stop a Hardware device] window willopen. Select the [USB Mass StorageDevice] and click the [OK] button.5. A [Safe to Remove Hardware] window willopen. Click the [OK] button.Removing the removable disk
《150》1. A USB Driver for MAC is not included with the software CD as MAC OS supports thecamera driver.2. Check the MAC OS. This camera is compatible with MAC OS 10.0 or later.3. Connect the camera to the Macintosh and turn the camera power on.4. A new icon will be displayed on the desktop after connecting the camera to the MAC.Using the USB Driver for MACSetting up the USB Driver for MAC1. Double click a new icon on the desktop and the folder in the memory will be displayed.2. Select an image file and copy or move it to MAC.●For Mac OS 10.0 or later : First complete uploading from computer to camera and thenremove the removable disk with the Extract command.●If a movie clip can’t play back on the Mac OS, please visit the following site.http://www.divx.com/divx/mac/CAUTION6. A [Unplug or Eject Hardware] window will open.Click the [Close] button and the removable diskwill be removed safely.7. Unplug the USB cable.[Click !]Removing the removable disk
《151》■You can download, view, edit and save your digital image and movie clip with this software.This software is only compatible with Windows.■To start the program, click [Start →Programs →Samsung →Digimax Master].●Downloading images1. Connect the camera to your PC.2. A window for downloading images will display afterconnecting the camera and your PC.- To download the captured images, select the [All(A)]button.- Select desired folder in the window and click the[All(A)] button. You can save captured images andselected folder.- If you click the [Cancel] button, downloading will becancelled.3. Click [Next(N) >] button.[Click !][Click !]Digimax Master
《152》7. Downloaded images will be displayed.4. Select a destination and make a folder to savedownloaded images and folder.- Folders will be made in order of date and images willbe downloaded.- Folder name will be made as you want and imageswill be downloaded.- After selecting a folder that was made before, images will be downloaded.5. Click [Next(N) >] button.6. A window will open as shown alongside.The destination of selected folder will be displayedon the upper side of the window. Click the [Start]button to download the images.[Click !][Click !]Digimax Master
《153》●Image viewer : You can view the stored images.- Image viewer functions are listed below.①Menu bar : You can select menus.File, Edit, View, Tools, Change functions, Auto download, help, etc.②Image selection window : You can select desired image in this window.③Media type selection menu : You can select image viewer, image edit, movie clip editfunction in this menu.④Preview window : You can preview a image or a movie clip and check the multi mediainformation.⑤Zoom bar : You can change preview size.⑥Folder display window : You can see folder location of selected image.⑦Image display window : Images of selected folder are displayed.※Refer to the [Help] menu in Digimax Master for further information.①⑤⑥⑦②③④Digimax Master
《154》●Image edit : You can edit the still image.- Image edit functions are listed below.①Edit menu : You can select the following menus.[Tools] : You can resize or crop the selected image. See the [Help] menu.[Modify] : You can modify image quality. See the [Help] menu.[Retouch] : You can change image or insert effects on the image. See the [Help] menu.②Drawing tools : Tools for editing an image.③Image display window : a selected image displays in this window.④Preview window : You can preview the changed image.※Refer to the [Help] menu in Digimax Master for further information.①②③④Digimax Master
《155》●Movie edit : You can get the still image, movie clip, narration, music files together in a movie clip.- Movie clip edit functions are listed below.①Edit menu : You can select the following menus.[Add] : You can add a desired multi media in a movie clip.[Edit] : You can change the brightness, contrast, colour and saturation.[Effect] : You can insert an effect.[Text] : You can insert texts.[Narration] : You can insert a narration.[Make] : You can save the edited multi media as a new file name.②Frame display window : You can insert multi media in this window.※Refer to the [Help] menu in Digimax Master for further information.①②Digimax Master
《156》■Digimax Reader is a Text recognition program. You can save an image file that is captured inthe Text mode, as a text file with this program.This software is only compatible with Windows.■To start the program, click [Start →Programs →Digimax Reader Eng].The following screen will appear.■How to use the Digimax Reader1. Connect the camera and the PC with a USB cable and download the images that werestored in the camera to the PC. * Please see page 120 ~ 122 for details on Connecting a camera and PC, Downloadingimages.2. Run the Digimax Reader.3. Click the Open( ) icon as shown alongside.Digimax Master
《157》4. Select the image you want to save as a text file.* Only an image that was taken with SAMSUNGcamera can be opened. 5. Click the Area Analysis( ) icon to scan the image.6. Part of the image you selected will be displayed asshown.7. Click the Character Recognition( ) icon.The part selected in the previous step will berecognized as text. 8. To save the section as a text, click the Save( )icon. A window as shown alongside will bedisplayed. Digimax Master
《158》●To get an image that can be recognized as a text : - Keep a distance of 20cm between the subject and the camera.- The subject need to be centered.- Avoid the camera shake to get a good image.●Refer to the [Help] menu in Digimax Reader for further information.INFORMATION 9. Select a file type that you want to.Selectable file type : *.TXT, *.HWP, *.DOC, *.RTFFAQ■Please check the following if the USB connection malfunctions.[Case 1] The camera power is off.→Turn the camera power on. We recommend using an AC power adapter in PCmode.[Case 2] USB Driver is not installed correctly.→Install the USB Driver correctly. Refer to page 110.[Case 3] The USB cable is not connected or you are using a cable with an incorrectspecification.→Use a USB cable with the correct specification.[Case 4] The camera is not recognized by your PC.Sometimes, the camera may appear under [Unknown Devices] in DeviceManager.→Install the camera driver correctly.Turn off the camera, remove the USB cable, plug in the USB cable again, andthen turn on the camera.Digimax Master
《159》[Case 5] There is an unexpected error during file transfer→Turn the camera power off and on again. Transfer the file again.[Case 6] How do I know my computer supports a USB Interface?→Check the USB port in your computer or keyboard.→Check the OS version. A USB Interface is available in Windows 98, 98SE,2000, ME .XP.→Check [Universal Serial Bus controllers] in Device Manager. Do the following tocheck [Universal Serial Bus controllers].Win 98/ME : Trace [Start →Settings →Control Panel →System →Device Manager →Universal Serial Bus controllers].Win 2000 : Trace [Start →Settings →Control Panel →System →Hardware →Device Manager →Universal Serial Buscontrollers].Win XP : Trace [Start →Control Panel →Performance andMaintenance →System →Hardware →Device Manager →Universal Serial Bus controllers].There must be USB Host Controller and USB root hub under [Universal SerialBus controllers].In addition, double-click on the USB Universal Host Controller and the USBRoot Hub to check if the Device Status states "This device is working properly".If the Device Status says the device is "not working properly", click the "Driver"tab and then click [Update Driver] or [Reinstall Driver].→When all the conditions mentioned above are met, the computer can supportthe USB interface.[Case 7] When using the USB hub.→There may be a problem in connecting the camera to the PC through the USBhub if the PC and the hub are not compatible. Wherever possible, connect thecamera to the PC directly.[Case 8] Are other USB cables connected to the PC?→The camera may malfunction when it is connected to the PC at the same timeas another USB cable. In this case, disconnect the other USB cable, andconnect only one USB cable to the camera.FAQ
《160》■When the movie clip doesn’t play back on the PC※When the movie clip recorded by the camera doesn’t play back on the PC, the causes aremostly due to the codec installed on the PC.●When the DirectX 9.0 or later is not installed→Install the DirectX 9.0 or later1) Insert the CD provided with the camera2) Run the windows explorer and select [CD-ROM drive:\ USB Driver\DirectX 9.0] folder andclick the DXESETUP.exe file.The DirectX will be installed. Visit the following site fordownloading the DirectX.http://www.microsoft.com/directx[Case 9] When I open the Device Manager (by clicking Start →(Settings) →ControlPanel →(Performance and Maintenance) →System →(Hardware) →DeviceManager), there are 「Unknown Devices」or 「Other Devices」entries with ayellow question mark(?) beside them or devices with an exclamation mark(!)beside them.→Right-click on the entry with the question(?) or exclamation (!) mark and select"Remove". Restart the PC and connect the camera the again. For Windows 98PC, remove the camera driver also, restart the PC, and then reinstall thecamera driver.→Double-click on the entry with the question (?) or exclamation (!) mark, click the"Driver" tab, and click [Update Driver] or [Reinstall Driver]. If a message appearsasking you to specify the location of the appropriate device driver, specify "USBDriver" in the CD supplied.[Case 10] In some security programs (Norton Anti Virus, V3, etc.), the computer may notrecognise the camera as a removable disk.→Stop the security programs and connect the camera to the computer. Refer tothe security program instructions about how to stop the program.FAQ
《161》■If a PC (Windows 98) stops responding while the camera and PC are connected repeatedly→If a PC (Windows 98) is turned on for a long time and connect the camera repeatedly, thePC may not recognise the camera. In this case, re-start the PC.■If a PC connected with the camera stops responding while Windows is starting.→In this case, disconnect the PC and the camera and Windows will start.If the problem happens continuously, set the Legacy USB Support to disable and re-startthe PC. The Legacy USB Support is in the BIOS setup menu. (The BIOS setup menudiffers from the PC manufacturers and some BIOS menus don’t have Legacy USBSupport) If you can’t change the menu by yourself, contact to the PC manufacturer orBIOS manufacturer.■If the movie clip can’t be deleted, removable disk can’t be extracted or an error messagedisplays during the file transfer.→If you install only the Digimax Viewer, the problems mentioned above occasionally happen.- Close the Digimax Viewer program by clicking the Digimax Viewer icon on the Taskbar.- Install all the application programs included in the software CD.(You must install the Movie clip codec)FAQ
6806-2415SAMSUNG TECHWIN CO., LTD.OPTICS & DIGITAL IMAGING DIVISION145-3, SANGDAEWON 1-DONG, JUNGWONGU,SUNGNAM-CITY, KYUNGKI-DO, KOREA462-121TEL : (82) 31-740-8086,8088, 8090, 8092, 8099FAX : (82) 31-740-8398, 8111www.samsungcamera.comSAMSUNG OPTO-ELECTRONICS AMERICA, INC.HEADQUARTERS40 SEAVIEW DRIVE, SECAUCUS, NJ07094, U.S.A.TEL : (1) 201-902-0347FAX : (1) 201-902-9342WESTERN REGIONAL OFFICE18600 BROADWICK ST.,RANCHO DOMINGUEZ, CA 90220, U.S.A.TEL : (1) 310-900-5263/5264FAX : (1) 310-537-1566www.samsungcamerausa.comSAMSUNG OPTO-ELECTRONICS UK LIMITEDSAMSUNG HOUSE1000 HILLSWOOD DRIVEHILLSWOOD BUSINESS PARKCHERTSEY KT16 OPS U.K.TEL : 00800 12263727(free for calls from UK only)UK Service Hotline : 01932455320www.samsungcamera.co.ukSAMSUNG OPTO-ELECTRONICS GMBHAM KRONBERGER HANG 6D-65824 SCHWALBACH/TS., GERMANYTEL : (49) 6196 66 53 03FAX : (49) 6196 66 53 66www.samsungcameras.deSAMSUNG FRANCE S.A.S.BP 51 TOUR MAINE MONTPARNASSE33, AV .DU MAINE75755, PARIS CEDEX 15, FRANCEHOTLINE PHOTO NUMÉRIQUE :00 800 22 26 37 27(Numéro Vert-Appel Gratuit)TEL : (33) 1-4279-2200FAX : (33) 1-4538-6858www.samsungphoto.frSAMSUNG TECHWIN MOSCOW OFFICERUSSIA, 125167, MOSCOW LENNINGRADSKY,PR-KT, 37-A, KORP14TEL : (7) 095-258-9299/96/98FAX : (7) 095-258-9297http://www.samsungcamera.ruTIANJIN SAMSUNG OPTO-ELECTRONICS CO.,LTD.7 PINGCHANG ROAD NANKAI DIST., TIANJINP.R CHINAPOST CODE:300190TEL : (86) 22-2761-8867FAX : (86) 22-2761-8864www.samsungcamera.com.cn＊Internet address - http : //www.samsungcamera.com/The CE Mark is a Directive conformitymark of the European Community (EC)2008. 4. 24

Navigation menu