Hanwha Techwin SSA-R1101V RFID Reader User Manual 20101004 v1 Appen

Samsung Techwin Co Ltd RFID Reader 20101004 v1 Appen

User manual

RFID ReaderUser Manual SSA-R1001VSSA-R1101V
Copyright ©2010 Samsung Techwin Co., Ltd. All rights reserved.Trademarkis the registered logo of Samsung Techwin Co., Ltd. The name of this product is the registered trademark of Samsung Techwin Co., Ltd. Other trademarks mentioned in this manual are the registered trademark of their respective company.RestrictionSamsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung Techwin.DisclaimerSamsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. Samsung Techwin reserves the right to change the contents of this document without prior notice.WarrantyIf the product does not operate properly in normal conditions, please let us know. Samsung Techwin will resolve the problem for free of charge. The warranty period is 3 years. However, the followings are excluded: If the system behaves abnormally because you run a program irrelevant to the system operation. Deteriorated performance or natural worn-out in process of time Sensory phenomenon that does not affect the performance or quality of the product (ex : working noise)•••RFID ReaderUser Manual
English _ 3safety informationCAUTIONRISK OF ELECTRIC SHOCK.DO NOT OPENCAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit.This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.WARNINGTo reduce the risk of fi re or electric shock, do not expose this appliance to rain or moisture.WARNINGBe sure to use only the standard adapter that is specifi ed in the specifi cation sheet.Using any other adapter could cause fi re, electrical shock, or damage to the product.Incorrectly connecting the power supply or replacing battery may cause explosion, fi re, electric shock, or damage to the product.Do not connect multiple controllers to a single adapter. Exceeding the capacity may cause abnormal heat generation or fi re.Securely plug the power cord into the power receptacle. Insecure connection may cause fi re.When installing the controller, fasten it securely and fi rmly. The fall of controller may cause personal injury.Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers fi lled with water on top of the controller. Doing so may cause personal injury due to fi re, electric shock, or falling objects.Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fi re or electric shock.If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the power source and contact the service center. Continued use in such a condition may cause fi re or electric shock.If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifi cations or attempted repair.). When cleaning, do not spray water directly onto parts of the product. Doing so may cause fi re or electric shock.CAUTIONDo not drop objects on the product or apply strong blows to it. Keep away from a location subject to excessive vibration or magnetic interference.Do not install in a location subject to high temperature (over 50°C), low temperature (below -25°C), or high humidity. Doing so may cause fi re or electric shock.If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall it.Remove the power plug from the outlet when there is a lighting storm. Neglecting to do so may cause fi re or damage to the product.Keep out of direct sunlight and heat radiation sources. It may cause fi re.Install it in a place with good ventilation.Avoid aiming the controller directly towards extremely bright objects such as sun.Apparatus shall not be exposed to dripping or splashing and no objects fi lled with liquids, such as vases, shall be placed on the apparatus.The Mains plug is used as a disconnect device and shall stay readily operable at any time.•1.2.3.4.5.6.7.8.9.10.1.2.3.4.5.6.7.8.9.SAFETY INFORMATION
FCC StatementCaution : Any changes or modifi cations in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:This device may not cause harmful interference, andThis device must accept any interference received, including interference that may cause undesired operation.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, any cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.- Consult the dealer or an experienced radio/TV technician for help.1)2)Read these instructions.Keep these instructions.Heed all warnings.Follow all instructions.Do not use this apparatus near water.Clean only with dry cloth.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifi ers) that produce heat.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fi t into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Only use attachments/accessories specifi ed by the manufacturer. Use only with cart, stand, tripod, bracket, or table specifi ed by the manufacturer, or sold with the apparatus. Unplug this apparatus when a card is used. Use caution when moving the cart/ apparatus combination to avoid injury from tip-over. Refer all servicing to qualifi ed service personnel. Servicing is required when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.1.2.3.4.5.6.7.8.9.10.11.12.13.14.IMPORTANT SAFETY INSTRUCTIONS4_ safety informationsafety information
English _ 5CONTENTScontentsPRODUCT INTRODUCTION66 Features6 What’s included7 At a Glance8 Cable Color Scheme8 Cable SelectionINSTALLATION AND EXTERNAL CONNECTION99 Installation10 Precautions on installation11 External ConnectionINITIALIZATION1212 Basic OperationsOUTPUT FORMAT1313 WIEGAND Output14 RS-232 OutputTROUBLESHOOTING1515 TroubleshootingPRODUCT SPECIFICATIONS1616 Product Specifi cations
6_ product introductionFEATURESThis model is an elegant-looking proximity reader that can be easily attached to a metal doorframe or the wall. Featured by the epoxy adhesion and aluminium case, R1001V/R1101V is shock-resistant with a high level of weather-proofi ng in any challenging weather conditions. The red and green indicators as well as the Piezo buzzer guarantee a stable and proper operation for you.13.56 MHz [MIFARE] Contactless Smart Card ReaderCompatible with ISO14443 Type A 3 Array LED Indicators (red and green) and Built-in Buzzer34 bit Wiegand / RS-232 Data OutputControl of External LED IndicatorsControl of External BuzzerEpoxy adhesion and aluminium caseReverse Polarity ProtectionWeatherproof and DustproofWHAT’S INCLUDEDCheck if the following items are included in the product package.What’s included in SSA-R1001VSSA-R1001VRFID Readeruser manual SSA-R1001VSSA-R1101VSSA-R1001VBezel READER Module 3mm Hex Wrench (x1)3.5x40mm screws (x2)3.5x25mm screws (x2)6x30mm Plastic Anchor (x2) Quick Guide CD ManualWhat’s included in SSA-R1101VRFID Readeruser manual SSA-R1001VSSA-R1101VSSA-R1101VBezel READER Module 3mm Hex Wrench (x1)3.5x40mm screws (x2)3.5x25mm screws (x2)6x30mm Plastic Anchor (x2)Quick Guide CD Manual◆◆◆◆◆◆◆◆◆product introduction
English _ 7PRODUCT INTRODUCTIONAT A GLANCEFront/RearLED Displays the system operation status using red and green indicators.Buzzer Piezo buzzer.Connection Cable Used to connect to the power or I/O cable.Fixing Hole Fixing hole for wall-mounting.Tamper Switch A tamper switch to detect falling from the wall.
8_ product introductionproduct introductionCABLE COLOR SCHEMEItem Cable Color Signal Line DescriptionPowerRed DC +12V DC +12V suppliedBlack GND Earth-grounding for powerInputBlue Buzzer Control BUZZER Control Input PortYellow LED Control LED Control Input PortOutputGreen Out Wiegand 0Wiegand Data 0 Output PortWhite Out Wiegand 1Wiegand Data 1 Output PortCommunicationPurple RS-232(TX)RS-232 Transmission Output PortTamperPinkTamper Output (COM)Tamper Output PortLight yellowTamper Output (NC)Tamper Output PortNot usedGrayNCNot ConnectedBrownOrangeCABLE SELECTIONItem Cable TypeCable Type1Power (DC12V) Belden #9409, 18 AWG 2 Conductor, UnshieldedBelden #9409, 18 AWG 2 Conductor, Unshielded 2WIEGAND OutputBuzzer ControlLED ControlTamper OutputBelden #9512, 22 AWG 4 Conductor, Shielded Belden #9514, 22 AWG 8 Conductor, Shielded3RS-232 Cable Belden #9829, 24 AWG 2-twisted pair, Shielded
English _ 9INSTALLATION AND EXTERNAL CONNECTIONinstallation and external connectionINSTALLATION- Inserted in the doorframe / attached to the wallTwo 6-32 or M3 holes are 3.3” (8.38 cm) away from each other vertically; between the two exists one 1/2” hole through which the reader cables are arranged. The midway hole is located 1.7” (4.31cm) down from the upper hole.(If the product is already installed, you can skip the follow step)Insert the reader cables to the midway hole and fi x the reader module with two 6-32 or M3 screws.Insert the reader module into the appearance case and tighten the screw (M6x8mm) using the hex wrench.1.2.3.Electric Gang Box MountWall MountMullion MountLowerReaderModuleBezel6-32 hole3.3”(8.38cm)Upper6-32 hole1/2”hole1.7”(4.31cm)6-32 or M3 Screws 6-32 or M3 ScrewsReaderModuleBezelGang Box3mm Hex Wrench 3mm Hex Wrench
10_ installation and external connectioninstallation and external connectionPRECAUTIONS ON INSTALLATIONIf installing on a metal wallIf you install the reader on a metal wall, the read range may be reduced.To avoid this problem, it is recommended to insert the spacer between the metal wall and the reader as shown below.If installing more than one reader side by side or front and backIf you install more than one reader side by side or front and back, the read range may be reduced. In this case, if you present a card to one reader, the other reader may recognize the same card, meaning two readers read the same card simultaneously.To avoid this problem, keep at least 20 cm of space between the two readers.MetalWallSpacerReader#Reader 2#Reader 1Minimum 20cm#Reader 1#Reader 2Minimum20cm<Front and Back><Side by Side>
English _ 11INSTALLATION AND EXTERNAL CONNECTIONEXTERNAL CONNECTIONWiring DiagramItemCable WiringPower Supply UnitConnect the DC+12V to the red line.Connect GND to the black line.Wiegand ConnectionConnect the green line of the product to the Wiegand D0 input port of the controller.Connect the white line of the product to the Wiegand D1 input port of the controller.LED Control To control the LED indicators, connect the yellow line to the output port (relay) of the controller.Buzzer Control To control the built-in buzzer, connect the blue line to the output port (relay) of the controller.RS-232 Connection Connect to the COM port of the PC. (Connect pin 2 of the DB-9 connector to the purple line; connect the black line of the device (GND) to pin 5 of the DB-9 connector)Tamper ConnectionConnect the pink line of the product to the GND terminal of the controller.Connect the light yellow wire of the product to the GND terminal of the controller.BlueYellowRS-232(GND)RS-232(TX)Red BlackBuzzer Control InLED Control InDC +12V GNDSSA-R1001V/SSA-R1101VWiegand Data 0 OutWiegand Data 1 OutGreenWhiteBrownBlack PCCONTROLLERPOWERTamper Output(COM)Tamper Output(NC)PinkLight yellow
12_ initializationinitializationBASIC OPERATIONSInitial State (when the power is supplied)When you apply power to the reader, it will sound a beep before entering Standby with the red indicator turn on .Using the cardPresent the card to the reader until you hear a beep and the red indicator turns green.When the reader has transferred the data to the controller, it returns to Standby with the red indicator turned on and waits for reading the next card.LED ControlYou can control the LED indicator of the device at your preference.Connect the LED control input line (yellow) to the NO port of the controller relay output, and GND to the COM port.Set the I/O of the controller so that you can change the color of the LED indicators. While the LED control is working, the green indicator stays solid.This function not only enables you to change the color representing Standby from red to green, but it can be also applied to make various modifi cations according to the different I/O settings of the controller.For more information about the I/O settings of the controller, refer to the user manual of the controller.Buzzer ControlYou can control the buzzer of the device at your preference.You can confi gure the I/O settings of the controller so that it sounds a beep. While the buzzer control is working, the product keeps sounding the beep.The controller can use the I/O settings to set the buzzer control so that it sounds an additional beep for authorized or unauthorized access upon user authentication.Furthermore, you can make various modifi cations according to the different I/O settings of the controller.For more information about the I/O settings of the controller, refer to the user manual of the controller.Card reading is not available while the buzzer control is sounding the buzzer.MCardXYZ[\]^_`lzj lzjWizzhTzYWWW
English _ 13OUTPUT FORMAToutput formatWIEGAND OUTPUTTiming DiagramData TypeBit 1 : Even Parity (bit2~bit17)Bit2~Bit33 : 4 byte ID numberBit34 : Odd Parity (bit18~bit33)•••100us1msDATA-0DATA-11235V0V0V5V0LOGIC 1 1 1 0 0n-2 n-1 n *n : 34
14_ output formatoutput formatRS-232 OUTPUTOutput WaveformData TypeStart (0X02H) Data (10 Char) End (0x03H) LRC START(0X02H) DATA (10 Char) END (0x03H) LRC Check the following settings:Baud Rate : 9600bpsDataBit : 8Parity : NoneStop Bit : 1LRC: This is the result of XOR operation of each byte from Start to End.M+15V 01 100000 0+3V-3V-15V0VData packet corresponding to ASCII character ‘A’8 Data BitsIndeterminateRegionStart Bit 2 Stop BitsSpace(=0)Mark(=1)LSB MSB
English _ 15TROUBLE SHOOTINGtroubleshootingTROUBLESHOOTINGIf the product does not function properly, please see the below for trouble shooting.PROBLEM SOLUTIONMy card is not read properly. 1) Check the rated voltage specifi ed in the user manual and the catalog.2) Ensure that you are using an ISO14443 Type A card. - Cards of 125 kHz format can not be used. 13.56 MHz cards of Type B, ISO15693 format can not be used. (Contact the card retailer regarding the card format.)3) If the problem persists, contact the nearest customer service for your assistance.When I turn on the product, it sounds a beep with dimly turned on indicator.1) Ensure that you are using a larger-capacity adaptor than specifi ed in the user manual or the catalog, which should cover the rated current consumption of the reader. If you are using multiple readers that are connected to one adaptor, make sure that the adaptor should be large enough to cover the current consumption multiplied by the reader count.2) Even with a large adaptor enough to supply adequate power, if the power cable is not a dedicated line (such as communication line or UPT cable), or if it’s so long to cause power loss, you’d better replace it with a dedicated line or reinforce it.3) If the problem persists, contact the nearest customer service for your assistance.The read range (R/R) of the card differs each time the product reads the card.1) The characteristics of a card are determined by the nature of the coils used and in the manufacturing process engaged by the card manufacturer. So what you do fi rst is to check that the cards in use are made by the same manufacturer.If you are using cards from different card makers, the read range (R/R) differs by the card, which is the result of normal operation.2) If you encounter a different read range (R/R) for each card that is made by the same manufacturer, please contact the nearest customer service.
product specifi cationsPRODUCT SPECIFICATIONSItem SSA-R1001V SSA-R1101VPower / Current DC 12V / Max.80mA Reading Time (Card) 30msInput Port 2ea : External LED Control, External Buzzer ControlOutput Port 34bit WiegandLED Indicator 2 Color LED (Red and Green) Beeper Piezo Buzzer Operating Temperature -25°C to +50°COperating Humidity 10% to 90% Relative Humidity Non-Condensing Color / Material Silver with Black/Polycarbonate & Aluminum Die casting Dimension (W x H x D(mm)) 47.0 x 120 .0 x 26.0 75.0 x 120.0 x 26.0Weight 250g ±10 340g ±10Correct disposal of batteries in this product(Applicable in the European Union and other European countries with separate battery return systems.)This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive 2006/66. If batteries are not properly disposed of, these substances can cause harm to human health or the environment.To protect natural resources and to promote material reuse, please separate batteries from other types of waste and recycle them through your local, free battery return system.Correct Disposal of This Product (Waste Electrical & Electronic Equipment)(Applicable in the European Union and other European countries with separate collection systems)This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal.16_ product specifi cations
P/No. : Z8100239401Awww.samsungsecurity.comwww.samsungtechwin.comSAMSUNG TECHWIN CO., LTD.Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745SAMSUNG TECHWIN EUROPE LTD. Samsung House, 1000 Hillswood Drive, Hillswood Business Park Chertsey, Surrey, UNITED KINGDOM KT16 OPSTEL : +44-1932-45-5300 FAX : +44-1932-45-5325SAMSUNG TECHWIN AMERICA Inc.1480 Charles Willard St, Carson, CA 90746, UNITED STATES Tol Free : +1-877-213-1222 FAX : +1-310-632-2195www.samsungcctvusa.comSALES NETWORK

Navigation menu